TILING,ROOFING, AC SHEET WITH FALSE CEILING AND CERTAIN OTHER CONNECTED B/R WORK IN ZONE B AREA AT FORT CANTT PRAYAGRAJ.

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

M&L for mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W (Gde-250 quality-B) complete all as specified & directed.

M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide including preparation of steel surfaces complete all as specified and directed.

S&F Stainless steel pipe as in drapery rod, 30 mm inner dia, Graded -304, fancy type including curtain ring , brakets, fancy type end cap, fixed to wall complete all as specified & directed.

Dismantling framed hardwood/soft wood timber scantlings 40 sq. cm and over in section, including removing bolt, nut etc in any position complete all as specified and directed.

M&L for 2nd class hard wood timber scantling clean swan fixed as girder, lintels, wall plates, joist purlin rafters etc complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed.

M&L for brickwork with old size sub class 'B' bricks, straight or curved on plain excn 6 m mean radius built in cement mortar 1:6 complete all as specified and directed

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified and directed.

M&L 15mm thick rendering on brick work or concreat surfaces of wall, in CM 1:4 mixed with water proofing compound (liquid) as per manufacture instruction, finish the surface even and fair in CM 1:4 Note : WPC shall be measured and paid saperately as supply only.

Supply only integral water proofing compound (ISI MARK) complete all as specified and directed.

M&L for preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of 1mm thick wall putty complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surfaces of wall in cement mortar 1:6 finished fair and even complete all as specified and directed.

M&L for three coats of white wash on newly plastered surface of walls including preparation of surface complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted including preparation of surface complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces on ceiling, finished fair & even complete all as specified and directed.

Material & labour for two coats of white wash on old plastered surface of ceilling after preparation of surface complete all as specified & directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, filling depressions of scrapped surfaces with wall care putty and applying a uniform layer of 1mm thick wall care putty (Make:- JK/Birla) including preparation of surfaces by rubbing with appropriate size of sand paper and applying two coats of oil bound distemper (approved colour/shed) complete all as specified and directed.

M&L for complete removal of existing treatment from wall (any numbers of layers)surfaces of wall including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coat of exterior acrylic weather proof paint (approved colour/ shade) including washing of floor, cleaning of glass , joinery,electrical fittings,wires etc. of drops & splash including 2mm thk wall care putty ( make J/K Birla) complete all as specified and directed.

Dismantling of AC sheet corrugated or semi corrugated including ridges as in roof or wall etc covering complete all as specified and directed.

S & F 6 mm thick asbestos cement, corrugated or semi- corrugated sheets fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed.

All as per item no 21 above but except AC sheet Note :- Old/serviceable AC sheet corrugated or semi corrugated obtained from item No. 20 here-in-before shall be re-used.

S&F 6 mm thick asbestos cement two piece adjustable plain wing ridge fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed.

S&F 2mm thick cloured fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F for 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts in lieu of screws and washer , in roof ,walls etc with grade of zinc coating 275 complete all as specified and directed.

S&F for 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

S & F prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed.

S & F prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with ‘L’ type or ‘J’ type or cranked hook bolts complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 sqm but not exceeding 4.0 Sqm each with shutter (without taking off shutters from the frames) complete all as specified and directed.

S&F in repairs aluminium anodised window (side hung type double shutter i.e glazed and guazed ) with aluminium anodized frame of aluminium section 62.5 mm x 37 mm x 1.5 mm thick with shutters having styles & rails of aluminium section 47.62 mm x 44.45 mm x 1.5 mm thick including jointing cleats, glazing clips, rubber packing, aluminium snap beading, screws anodized aluminium fittings such as hinges, tower bolts, handles etc. including 5.5 mm thick ordinary plain glass, aluminium designer grill and stainless steel wire mesh 0.36mm dia 1.40mm aperture etc complete all as apecified and directed.

S&F for pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. Note:- The quoted unit rate under this item shall deemed to be included one shop coat of primer.

S & F flush shutters 35 mm thick, factory made, kiln seasoned and ASCU treated solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and directed.

S&F second class hardwood glazed and skeleton door shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded,fitted with cut and mitred beads for securing glass, etc. size of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specifed and directed.

S&F in repair steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars dovetailed or welded including two coat of synthetic enamel paint over factory primed shop coat complete all as specified and directed. Note:- Red oxide primer coat have been cattered by factory.

S&F in repair steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars dovetailed or welded including two coat of synthetic enamel paint over factory primed shop coat all as specified and directed. Note:- Red oxide primer have been cattered by factory.

S&F in repair steel ventilators, fixed type, with glazing bars guaged bar complete all as spcified and directed.

S&F 2nd class hard wood (sall) plain solid straight chowhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as spcified and directed.

S & F in repair block board 18/19 mm thick , interior grade,commercial type , fixed with screws to timber frame work complete all as specified and directed.

S&F in repair 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified.

S&F 19mm width 1st class wooden Beads, straight (any size) for glazed or gauzed joinery, partical boards, renewed, including mitres etc. and removing old beads to Store complete all as specified and as directed.

S&F in repair continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S & F in repair stainless steel plate rack (utensil rack) of size(600mmx750mm) and depth 300 mm made with 0.63 mm thick stainless steel sheet fixed with brass screw including necessary fittings, nut/bolts , washer etc. complete all as specified and directed .( Sample of stainless steel plate rack shall be of approved by Accepting Officer )

S & F hasp and staple 100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified and directed.

M&L framed work as in grills ,grating etc with ends of bars shouldered and riveted,or forged in to spike frame guard bars, iron door hold fast etc confirming to Fe-41o-o or 310-0 complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in plinth protection, finished even and smooth without using extra cement, including making joints 10 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand mortar in 1:3 complete all as specified and directed.

M&L for providing 50mm thick cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in floor, (Laid in alternate pannel) finished the surface even and smooth without using extra cement complete all as specified and as directed

M&L for 20 mm thick wearproof topping as specified (incorporating an approved metallic floor hardner in ration of 1:4 ), laid on concrete floors and pavings, and finished the surface even and smooth and even (except metallic hardner) complete all as specified and directed. Note : Metallic floor hardner shall be measured and paid saperately as supply only.

Supply only metallic floor hardner complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete and removing rubbish off from the premises complete all as specified and directed.

M&L for joint free Non Skid ceramic tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic white tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles [premium quality] as in vertical surface of walls such as skirting / dado and risers to steps, size of tile 450x300mmx7mmm or 350x250x7mm thick set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles over and including 10 mm thick rendering as in backing of tiles in cement mortar in 1:4 complete all as specified and directed.

M&L for vitrified light shed tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floors, with set and jointed in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Vitrified Light shed tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm in skirting with set and jointed in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering as in backing of tiles in cm 1;4 complete all as specified and directed.

M&L for joint free non skid ceramic white tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm , in skirting as vertical surfaceetc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including10 mm thick rendering as in backing of tiles in cement mortar in 1:4 complete all as specified and directed.

M&L for 1st quality non skid coloured ceramic ENDURA tiles n exc 0.11 Sqm 10 mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for 25 mm thick cement concrete levelling course of type B-0 (1:2:4) finished complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006, 60 mm thick, M-35 grade with grey cement and pigment complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for providing cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in side of paver blocks boundingcomplete all as specified and as directed.

Material and labour for providing cement concrete 1:3:6 type C2 75 mm thick using 40mm graded aggregate as in sub base complete all as specified and as directed

Dismantling stone slabs laid and pointed in cement mortar of any description or thickness in floors, aprons etc.complete all as specified and directed.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and incluiding 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

M&L for 18 to 20 mm thick machine cut mirror polished kota stone slab as in landing, step flooring, over & including 20mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed with grey cement sluury mixed with pigment to match the shade of the slabe including rubbing and polishing complete all as specified and as directed.

M&L for 18 to 20 mm thick machine cut mirror polished kota stone slab in vertical surface of wall such as in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match stone, over and including 10 mm thick rendering or bedding layer in cement mortar 1:4 with grey cement sluury mixed with pigment to match the shade of the slabe including rubbing and polishing complete all as specified and as directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutters from the frames) complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of Mild Steel tubes for top & bottom rails. Mild Steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the Mild Stee frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in SSR Part-II 2010 and as directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F 125 mm size aluminium anodised handles, cast type complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal/wooden frame complete all as specified and directed.

S&F for 3 mm thick sheet glass of ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm each pane complete all as specified and directed.

S&F 4 mm thick figured sheet glass ordinary quality and glazing with oil putty or wooden beads in square area not exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples in repair complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10cm width or girth over a coat of pink primer including preparation of surfaces complete and all as specified and directed.

S&F galvanised mild steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples , complete all as specified and as directed.

S&F in repair ceiling using 'E' board of size 605 mm x 605mm x 4mm thick, white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanised steel sheet and of size 24mmx32mmx300 mm board spaced at 1200 mm maximum centre to centre. Hangers of GI wire 4mm dia to be fixed by approved rawal plug level and fasteners and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 1200mm longer cross tee (with double stitching) to be interlocked between main runners at 600mm centre to centre from 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm doubles to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee.(with double stitching) to be interlocked between main runners at 600mm centre to centre from 1200x600mm modules cross tee longer than 600mm to be supported independently. Tee perimeter wall angle shall be 0.45mm thick GS sheet of size 19 mmx19 mm and 300mm long of white colour all as per manufacture's instructions compete all as specified & directed.

S&F in repair mild steel tubing of 25mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings decorative holder and CP brass brackets (wall to wall or flush to wall) for securing to curtain rod complete all as specified and directed.

S & F in repair tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified and directed.

S&F in repair two way angle valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle for iron pipe or for unions 15 mm bore complete all as specified and directed.

S&F in repair bib taps fancy type cast copper alloy chromium plated with capstan head screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets, 32 mm bore PVC flush pipe 600mm long complete all as specified and directed.

S& F in repair PVC connections 15 mm size with PTMT, 450 mm length with brass nuts at both ends complete all as specified and directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) bedding, connection to trap, outgoing flushing pipe, anti sypohonage pipe,100 mm bore 'P' or 'S' trap etc complete all as specified and directed.

S&F in repairs vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc) with aluminium hinging device complete all as specified and directed. Note :- Plastic seat cover shall be measured separetly as supply only as considered under respective items.

Supply only plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F in repair vitreous China wash hand basin white, flat back of size 550mmx400mm fixed on and fixing of cantilever brackets of mild steel angle 35mmx35mmx5mm , 32mm dia brass waste coupling and 32 mm dia PVC waste pipe (rigid quality)and PVC connections 15 mm size with PTMT, 450 mm length including fixing of tap etc.complete all as specified and directed. Note :- Pillar tap/mixture shall be measured and paind separetely as supply only under respective item of BoQ.

Supply only pillar taps cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without lettered hot or cold letter with long screwed shank and fly nuts, screwed for iron pipe 15mm bore pipe complete all as specified and directed.

Supply only 32mm dia waste pipe of polythelene,flexible, for wash hand basin or urinals complete all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore including removing from site complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore including removing from site complete all as specified and directed.

S&F galvanised mild steel water tubes, 15 mm bore with all fittings, 'medium grade', ISI marked, galvanised, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F galvanised mild Steel water tubes, 20 mm bore with all fittings, 'medium grade', ISI marked, galvanised, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed fro iron pipe and fixed for 20mm bore size (minimum weight 210 gms) complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethene water storage tanks"ISI marked"double layered (Cylindrical vertical with closed top) hoisted and fixed in position including tank nipple etccomplete all as specified and as directed.

S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and directed.

S&F in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210gms) complete all as specified and directed.

S&F in repairs PVC (SWR) pipe 75 dia single socket in any length with rubber gasket cup washing, jointed fixed to wall including dismantling complete all as specified and directed.

S&F in repairs PVC (SWR) pipe 75 single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC (SWR) bends of 75mm dia fixed to pipes in wall making good with CM(1:4) or PCC 1:2:4 if required including dismentling complete all as specified and directed.

S&F in repair PVC (SWR) bends of 75 mm dia with oval access door fixed to PVC pipe joint with rubber solvant complete all as specified and directed.

S&F in repair 100mm dia CP greating fixed with coloured cement joint to match the existing surface of tile complete all as specified and directed.

M/s Rahul Kumar Agrawal

Shivagya Engineering

M/S Akhilesh Enterprises

ms shanti sons

KRISHNA BAHADUR

creative construction co.

shweta constructions