Providing safety arrangements, barricading, weldmesh partition and samiyana pandhal arrangements to the counting centre for the state election 2026 at Government college of Engineering(IRTT), Chithode in Erode District.

Dismantling clearing away and carefully stacking of materials useful for reuse of Brick / stone masonry in Cement mortar walls under 3m high as directed by the departmental Officer

Hire charges for Providing weldmesh using 7.5 X 2.5cm 10 gauge with silver scantling of varies length and size for vertival and horizontal supports and cross supports using C.W reepers of size 2"x1" including cost of materials and labour charges for fixing in postion with all necessary accessories etc., complete complying with standard specification as directed by the departmental officers.

Hire charges for providing weldmesh Door arrangements by using weldmesh of size 2.50 cm x2.50 cm and outer and inner frame 20x20mm square tube including cost of nails , screws and clamps and removing the same after the counting is over including conveyance and stacking as directed by the departmental officers.

Hire charges for closing the window opening with 12 mm thick water proof plywood using country wood reeper of size 50 x 25 mm including making necessary holes in the walls, fixing the reeper and plywood with nails, screws and binding wire and after the counting is over removing of all fitting materials and redoing the damages portion to the original condition etc complete as directed by the departmental officers

Dismantling clearing away and carefully stacking the materials for reuse of weldmesh and Plywood partitions etc., complete complying with standard specification and as directed by the departmental officers.

For Superstructure in Ground Floor

For Superstructure in First Floor

Manufacturing supplying and fixing of Fully panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided 6nos. of holdfasts 00 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 4nos. One the top of each shutter, one at lock rail and the other at the bottom are provided. 1no. Aldrop is provided at lock rail section in the door 3 Nos of handle are to be provided, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers. - Double leaf of size 1.20m x 2.10m.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.