Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹23.5 Cr
EMD Value
₹23.5 L
Closing Date
14 Sept 2023, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Construction of 40 Nos. Type-II Family Quarters and Administrative Block at Bolani Ores Mines, Keonjhar, Odisha
NBCC/ODISHA/SBG/NIT/23-24/008
NBCC/ODISHA/SBG/NIT/23-24/008
Open Tender-Domestic
Civil Works General
Dhenkanal, Odisha
₹11,800
₹23.5 L
14 Sept 2023
30 Aug 2023
14 Sept 2023
14 Sept 2023
25 Sept 2023
BILL OF QUANTITIES
Construction of 40 Nos. Type-ll (G+1) Family Quarters (2800 sqm built up area) & Administrative Block (2850 sqm built up area)
at Bolani Ores Mines.
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Earth work in excavation by mechanical means (Hydraulic
excavator)/manual means over areas (exceeding 30 cm in
1 2.6 depth, 1.5 m in width as well as 10 sqm on plan) including getting
out and disposal of excavated earth with all lead and lift, as
directed by Engineer-in-charge.
Earth work in excavation by mechanical means (Hydraulic
excavator) / manual means in foundation trenches or drains
(not exceeding 1.5 m in width or 10 sqm on plan), including
dressing of sides and ramming of bottoms, including getting
out the excavated soil and disposal of surplus excavated soil
as directed by Engineer-in-charge, with all lead and lift.
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers not
3 2.25 exceeding 20cm in depth, consolidating each deposited layer Cum 3597.69 270.03 971466.10
by ramming and watering, for all lead and lift as directed by
Engineer-in-charge
Excavating, supplying and filling of local earth (including royalty)
by mechanical transport upto a lead of 5km also including
ramming and watering of the earth in layers not exceeding 20 cm
in trenches, plinth, sides of foundation etc. complete.
Supplying and filling in plinth with sand under floors,
5 2.27 including watering, ramming, consolidating and dressing Cum 1658.13 2298.00 3810391.60
complete as directed by Engineer-in-charge
Extra for every additional lift of 1.5 m or part thereof in
Surface dressing of the ground including removing vegetation
7 2.28 and inequalities not exceeding 15 cm deep and disposal of
rubbish, lead up to 50 m and lift up to 1.5 m.
2.28.1 All kinds of soil Sqm 2500.00 29.93 74829.74
Clearing jungle including uprooting of rank vegetation, grass,
brush wood, trees and saplings of girth up to 30 cm measured at
a height of 1 m above ground level and removal of rubbish up to
a distance of 50 m outside the periphery of the area cleared.
Felling trees of the girth (measured at a height of 1 m above
ground level), including cutting of trunks and branches, removing
the roots and stacking of serviceable material and disposal of
unserviceable material.
2.33.1 Beyond 30 cm girth upto and including 60 cm girth Each 2.00 467.05 934.11
2.33.2 Beyond 60 cm girth upto and including 120 cm girth Each 6.00 2081.04 12486.23
B Concrete Work
Providing and laying in position cement concrete of
10 4.1 specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural
11 4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived Cum 168.86 7831.36 1322411.96
from natural sources)
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural
12 4.1.5 sources : 6 graded stone aggregate 20 mm nominal size derived Cum 211.67 7265.95 1537962.73
from natural sources)
1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded
stone aggregate 40 mm nominal size)
1:4:8 (1 cement : 4 manufactured sand derived from Recycled
14 4.1.8A Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm Cum 49.50 5014.10 248197.83
nominal size Recycled Aggregate (RA)
Providing and laying damp-proof course 40mm thick with cement
15 4.11 concrete 1:2:4 (1 cement : 2 coarse sand (zone- III): 4 graded Sqm 397.04 480.88 190927.57
stone aggregate 12.5mm nominal size)
Providing & applying a coat of residual petroleum bitumen of
grade of VG-10 of approved quality using 1.7kg per square
16 4.13 metre on damp proof course after cleaning the surface with Sqm 397.04 121.06 48064.35
brushes and finally with a piece of cloth lightly
soaked in kerosene oil.
Making plinth protection 50mm thick of cement concrete 1:3:6
(1 cement : 3 coarse sand : 6 graded stone aggregate 20
mm nominal size) over 75mm thick bed of dry brick ballast 40
17 4.17 mm nominal size, well rammed and consolidated and Sqm 497.04 724.80 360256.72
grouted with fine sand, including necessary excavation,
levelling & dressing & finishing the
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Brick edging in full brick width and half brick depth
including excavation refilling and disposal of surplus earth lead
upto 50 metres. With common burnt clay F.P.S.(non
modulur) bricks of class designation 75
With common burnt clay F.P.S. (non modular) bricks of
class designation 7.5
C Reinforced Cement Concrete
Centering and shuttering including strutting, propping etc.
and removal of form for :
Foundations, footings, bases of columns, etc. for mass
Walls (any thickness) including attached pilasters, buttereses,
plinth and string courses etc.
Suspended floors, roofs, landings, balconies and access
23 5.9.4 Shelves (Cast in situ)
Lintels, beams, plinth beams, girders, bressumers and
25 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 2981.30 855.16 2549485.60
26 5.9.7 Stairs, (excluding landings) except spiral-staircases Sqm 271.27 699.39 189720.93
27 5.9.16 Edges of slabs and breaks in floors and walls
28 5.9.19 Weather shade, Chajjas, corbels etc., including edges Sqm 548.80 866.54 475555.14
Steel reinforcement for R.C.C. work including
29 5.22 straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or
Steel reinforcement for R.C.C. work including
30 5.22A straightening, cutting, bending, placing in position and
binding all complete above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or
Add for plaster drip course/ groove in plastered surface or
moulding to R.C.C. projections. (40 mm x 6mm band)
Providing and laying in position machine batched and
machine mixed design mix M-25 grade cement concrete for
reinforced cement concrete work, using cement content as
per approved design mix, including pumping of concrete to
site of laying but excluding the cost of centering,
shuttering, finishing and reinforcement, including
33 5.33 admixtures in recommended proportions as per IS: 9103 to
accelerate, retard setting of concrete, improve workability without
impairing strength and durability as per direction of Engineer-in-
(Note :- Cement content considered in this item is @ 330
kg/cum. Excess/ less cement used as per design mix is
payable/recoverable separately).
5.33.1 All works upto plinth level Cum 615.07 9233.48 5679239.34
5.33.2 All works above plinth level upto floor V level Cum 1190.00 10958.58 13040713.13
Add for using extra cement in the items of design mix over and
above the specified cement content therein.
Providing and fixing of expansion joint system related with floor
location as per drawings and direction of Engineer-In Charge.
The joints system will be of extruded aluminum base members,
self aligning / self centering arrangement and support plates
etc. as per ASTM B221-02. The system shall be such that it
provides floor to floor /floor to wall expansion control system for
35 5.44 various vertical localtion in load application areas that
accommodates multi directional seismic movement without
stress to it's components. System shall consist of metal
profiles with a universal aluminum base member
designed to accommodate various project conditions and
The cover plate shall be designed of width and thickness
required to satisfy projects movement and loading
requirements and secured to base members by utilizing
manufacturer’s pre-engineered self- centering
arrangement that freely rotates / moves in all directions. The
Self - centering arrangement shall exhibit circular sphere
ends that lock and slide inside the corresponding aluminum
extrusion cavity to allow freedom of movement and flexure
in all directions including vertical displacement.
Provision of Moisture Barrier Membrane in the Joint System to
have watertight joint is mandatory requirement all as per the
manufactures design and as approved by Engineer -in-Charge.
(Material shall confirm to ASTM 6063).
5.44.1 Floor Joint of 100 mm gap Metre 44.00 6167.30 271361.18
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and fixing of expansion joint system related with wall
joint (internal/ external) location as per drawings and direction of
Engineer-In- Charge. The joints shall be of extruded
aluminum base members, self aligning / centering
arrangement and support plates as per ASTM B221- 02. The
material shall be such that it provides an Expansion Joints
System suitable for vertical wall to wall/ wall to corner
application, both new and existing construction in office
Buildings & complexes with no slipping down tendency
amongst the components of the Joint System. The Joint
System shall utilize light weight aluminum profiles exhibiting
minimal exposed aluminum surfaces mechanically snap
locking the multicellular to facilitate movement. (Material
shall confirm to ASTM 6063.)
5.45.1 Wall Joint of 100 mm gap Metre 86.40 5141.59 444233.13
Providing and fixing of expansion joint system of approved make
and manufactures for various roof locations as per approved
drawings and direction of Engineer-In-Charge. The joints shall
be of extruded aluminum base members with, self aligning and
self centering arragement support plates asper ASTM B221-
02. The system shall be such that it provides watertight roof to
roof/roof to corner joint cover expansion control system that
is capable of accommodating multidirectional seismic
movement without stress to its components. System shall
consist of metal profile that incorporates a universal aluminum
base member designed to accommodate various project
conditions and roof treatments.
The cover plate shall be designed of width and thickness
required to satisfy movement and loading requirements and
secured to base members by utilizing manufacturer’s
preengineered self-centering arrangement that freely
rotates / moves in all directions. The Self centering
arrangement shall exhibit circular sphere ends that lock and
slide inside the corresponding aluminum extrusion cavity to
allow freedom of movement and flexure in all directions
including vertical displacement. The Joint System shall
resists damage or deterioration from the impact of falling
ice, exposure to UV, airborne contaminants and
occasional foot traffic from maintenance personnel.
Provision of Moisture Barrier Membrane in the Joint System
to have water tight joint is mandatory requirement. (Material
shall confirm to ASTM
5.46.1 Roof Joint of 100 mm gap Metre 44.00 5767.55 253772.28
D Masonry Work
Brick work with common burnt clay F.P.S. (non modular) bricks
of class designation 7.5 in foundation and plinth in:
6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 20.00 7079.72 141594.34
Brick work with non modular fly ash bricks conforming to
IS:12894, class designation 10 average compressive
strength in super structure above plinth level up to floor V
6.34.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 980.00 8162.21 7998965.59
Half brick masonry with non modular fly ash bricks of
40 6.45 class designation 10, conforming IS :12894, in super
structure above plinth and upto floor V level.
6.45.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 4813.14 1031.03 4962486.18
Extra for providing and placing in position 2 Nos 6mm dia.
M.S. bars at every third course of half brick masonry.
E Cladding Work
Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills, facias and
similar locations of required size, approved shade, colour and
42 8.2 texture laid over 20 mm thick base cement mortar 1:4 (1 cement
: 4 coarse sand), joints treated with white cement, mixed with
matching pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high gloss finish etc.
complete at all levels.
8.2.2 Granite of any colour and shade
8.2.2.2 Area of slab over 0.50 sqm Sqm 10.00 4705.47 47054.75
Extra for fixing marble /granite stone, over and above
corresponding basic item, in facia and drops of width upto 150
mm with epoxy resin based adhesive, including cleaning
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Extra for providing opening of required size & shape for
wash basin/ kitchen sink in kitchen platform, vanity
counter and similar location in marble/ Granite/ stone work,
including necessary holes for pillar taps etc. including
moulding, rubbing and polishing of cut edges
Providing and fixing Ist quality ceramic glazed wall tiles
conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by
45 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, Sqm 1808.14 1130.77 2044583.93
over 12 mm thick bed of cement mortar 1:3 (1 cement : 3
coarse sand) and jointing with grey cement slurry @ 3.3kg
per sqm, including pointing in white cement mixed with
pigment of matching shade complete.
Providing edge moulding to 18mm thick marble stone
counters, Vanities etc. including machine polishing to edge to
give high gloss finish etc. complete as per design approved by
Engineer-in-Charge.
F Wood Work & PVC Work
Providing and fixing factory made uPVC white colour
casement/casement cum fixed glazed windows comprising of
uPVC multi-chambered frame, sash and mullion (where ever
required) extruded profiles duly reinforced with 1.60 ± 0.2 mm
thick galvanized mild steel section made from roll forming
process of required length (shape & size according to uPVC
profile), uPVC extruded glazing beads of appropriate dimension,
EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc
alloy (white powder coated) casement handles, G.I fasteners 100
x 8 mm size for fixing frame to finished wall, plastic packers,
plastic caps and necessary stainless steel screws etc. Profile of
frame & sash shall be mitred cut and fusion welded at all
corners, mullion (if required) shall be also fusion welded
including drilling of holes for fixing hardware's and drainage of
water etc. After fixing frame the gap between frame and adjacent
wall shall be filled with weather proof silicon sealant over backer
rod of required size and of approved quality, all complete as per
approved drawing & direction of Engineer-in-Charge. (Single /
double glass panes and silicon sealant shall be paid separately).
Variation in profile dimension in higher side shall be accepted but
no extra payment on this account shall be made.
Casement window double panels with top fixed with S.S.
friction hinges (350 x 19 x 1.9 mm) made of (small series)
frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm
all having wall thickness of 1.9 ± 0.2 mm and single glazing
bead of appropriate dimension. ( Area of window upto 2.50
Providing and fixing factory made uPVC white colour sliding
glazed door comprising of uPVC multi-chambered frame with in-
built roller track and sash extruded profiles duly reinforced with
1.60 ± 0.2 mm thick galvanized mild steel section made from roll
forming process of required length (shape & size according to
uPVC profile), appropriate dimension uPVC extruded glazing
beads, uPVC extruded interlock and uPVC extruded Inline sash
adaptor (if required), EPDM gasket, wool pile, zinc alloy
(white powder coated) handle with key on one side of extreme
panels along with zinc plated mild steel multi point locking having
transmission gear with keeps, zinc alloy (white powder coated)
cresent lock (if required), stainless steel (SS 304 grade) body
with adjustable double nylon rollers (weight bearing capacity to
be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to
finished wall and necessary stainless
steel screws etc. Profile of frame & sash shall be mitred cut and
fusion welded at all corners, including drilling of holes for fixing
hardware's and drainage of water etc. After fixing frame the gap
between frame and adjacent finished wall shall be filled with
weather proof silicon sealent over backer rod of required size
and of approved quality, all complete as per approved drawing &
direction of Engineer-in-Charge. (Single / double glass panes,
Two track two panels sliding door made of (big series) frame
67 x 50 mm & sash 46 x 82 mm both having wall thickness
9.147F.1 of 2.3 ± 0.2 mm and single glazing bead / double glazing Sqm 5.00 7318.06 36590.28
bead of appropriate dimension. (Area of door above 2.00
sqm upto 5.00 sqm)
Providing and fixing ISI marked flush door shutters
conforming to IS : 2202 (Part I) non-decorative type, core of
49 9.21 block board construction with frame of 1st class hard wood and
well matched commercial 3 ply veneering with vertical grains or
cross bands and face veneers on both faces of shutters:
35 mm thick including ISI marked Stainless Steel butt
hinges with necessary screws
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Extra for Providing and fixing flush doors with decorative
50 9.22 veneering instead of non decorative ISI marked flush door
shutters conforming to IS: 2202 (Part I)
Extra for providing lipping with 2nd class teak wood battens
51 9.23 25 mm minimum depth on all edges of flush door shutters (over Sqm 250.00 426.81 106702.16
all area of door shutter to be measured).
Extra for providing vision panel not exceeding 0.1 sqm in all type
52 9.24 of flush doors (cost of glass excluded) (overall area of door
shutter to be measured):
9.24.1 Rectangular or square Sqm 10.00 184.96 1849.61
53 9.7.7 Float glass panes
9.7.7.1 4 mm thick glass pane (weight not less than 10kg/sqm). Sqm 146.00 2017.19 294509.22
Extra for cutting rebate in flush door shutters (Total area
of the shutter to be measured).
Providing and fixing M.S. grills of required pattern in frames
of windows etc. with M.S. flats, square or round bars etc.
including priming coat with approved steel primer
9.48.1 Fixed to steel windows by welding kg 6164.00 192.46 1186306.80
Providing and fixing chromium plated brass 100 mm mortice
56 9.88 latch and lock with 6 levers and a pair of lever handles of Each 105.00 869.25 91271.01
approved quality with necessary screws etc. complete.
Providing and fixing IS : 12817 marked stainless steel butt
9.71 hinges (heavy
weight) with stainless steel screws etc. complete :
Providing and fixing bright finished brass tower bolts (barrel type)
necessary screws etc. complete :
Providing and fixing special quality bright finished brass
9.79 cupboard or ward robe locks with four levers of approved quality
including necessary screws etc. complete.
Providing and fixing chromium plated brass handles with
necessary screws etc. complete:
Providing and fixing bright finished brass hanging type floor door
stopper with necessary screws, etc. complete.
Providing and fixing bright finished brass casement
window fastener with necessary screws etc. complete.
Providing and fixing oxidised M.S. casement stays (straight peg
type) with necessary screws etc. complete.
9.68.1 300 mm weighing not less than 200 gms Nos 116.00 63.00 7308.06
Providing and fixing aluminium extruded section body
tubular type universal hydraulic door closer (having brand logo
with ISi, IS : 3564, embossed on the body, door weight upto
36 kg to 80 kg and door width from 701 mm to 1000 mm),
with double speed adjustment with necessary accessories
and screws etc. complete.
Providing and fixing nickel plated M.S. pipe curtain rods
with nickel plated brackets :
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and fixing factory made P.V.C. door frame of size
50x47 mm with awall thickness of 5 mm, made out of extruded
5mm rigid PVC foam sheet, mitred at corners and joined with 2
Nos of 150 mm long brackets of 15x15 mm M.S. square tube,
the vertical door frame profiles to be reinforced with 19x19 mm
M.S. square tube of 19 gauge, EPDM rubber gasket weather
seal to be provided through out the frame. The door frame to be
fixed to the wall using M.S. screws of 65/100 mm size, complete
as per manufacturer’s specification and direction of Engineer in-
Providing and fixing factory made panel PVC door shutter
consisting of frame made out of M.S. tubes of 19 gauge
thickness and size of 19 mm x 19 mm for styles and 15x15 mm
for top & bottom rails. M.S. frame shall have a coat of steel
primers of approved make and manufacture.
M.S. frame covered with 5 mm thick heat moulded PVC 'C'
channel of size 30 mm thickness, 70 mm width out of which 50
mm shall be flat and 20 mm shall be tapered in 45 degree angle
on both side forming styles and 5 mm thick, 95 mm wide PVC
sheet out of which 75mm shall be flat and 20 mm shall be
tapered in 45 degree on the inner side to form top and bottom rail
and 115 mm wide PVC sheet out of which 75 mm shall be flat
and 20 mm shall be tapered on both sides to form lock rail. Top,
bottom and lock rails shall be provided both side of the panel. 10
mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided
as gap insert for top rail & bottom rail, paneling of 5 mm thick
both side PVC sheet to be fitted in the M.S. frame welded/ sealed
to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide
PVC sheet beading on inner side, and joined together with
solvent cement adhesive. An additional 5 mm thick PVC strip of
20 mm width is to be stuck on the interior side of the 'C' Channel
using PVC solvent adhesive etc. complete as per direction of
9.120.2 30 mm thick pre laminated PVC door shutters Sqm 80.64 2610.51 210511.35
Providing and fixing fly proof stainless steel grade 304 wire
gauge, to windows and clerestory windows using wire gauge
65 9.135.2 with average width of aperture 1.4 mm in both directions Sqm 381.00 1118.33 426082.12
with wire of dia. 0.50 mm all complete. With 12 mm mild steel U
Providing and fixing in position collapsible steel shutters with
vertical channels 20x10x2 mm and braced with flat iron
diagonals 20x5 mm size, with top and bottom rail of T iron
66 10.3 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, Sqm 26.80 9992.20 267791.02
nuts, locking arrangement, stoppers, handles, including
applying a priming coat of approved steel
Providing and fixing factory made ISI marked steel glazed
windows and ventilators, side /top /centre hung, with
beading and all members such as F7D,F4B, K11 B and K12 B
etc. complete of standard rolled steel sections, joints mitred
67 10.11 and flash butt welded and sash bars tenoned and riveted,
including providing and fixing of hinges, pivots, including
priming coat of approved steel primer, but excluding the cost
of other fittings, complete all as per approved design, (sectional
weight of only steel members shall be measured for payment).
Fixing with 15x3 mm lugs 10 cm long embedded in cement
10.11.1 concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 kg 50.00 186.77 9338.43
coarse sand : 6 graded stone aggregate 20 mm nominal size)
Providing and fixing T-iron frames for doors of mild steel Tee-
68 10.13 sections, joints mitred and welded, including screws and
applying a priming coat of approved steel primer.
Fixing with 15x3 mm lugs 10 cm long embedded in cement
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3
coarse sand : 6 graded stone aggregate 20
mm nominal size).
Steel work in built up tubular (round, square or
rectangular hollow tubes etc.) trusses etc., including
69 10.16 cutting, hoisting, fixing in position and applying a priming coat of
approved steel primer, including welding and bolted with
special shaped washers etc. complete.
10.16.3 Electric resistance or induction butt welded tubes. kg 5.00 149.77 748.83
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Steel work welded in built up sections/ framed work,
including cutting, hoisting, fixing in position and applying a
priming coat of approved steel primer using structural steel
etc. as required.
In gratings, frames, guard bar, ladder, railings, brackets,
gates and similar works
Providing and fixing stainless steel (Grade 304) railing made
of Hollow tubes, channels, plates etc., including welding,
grinding, buffing, polishing and making curvature (wherever
required) and fitting the same with necessary stainless steel
nuts and bolts complete, i/c fixing the railing with necessary
71 10.28 accessories & stainless steel dash fasteners , stainless kg 940.00 651.01 611945.10
steel bolts etc., of required size, on the top of the floor or the
side of waist slab with suitable arrangement as per approval of
Engineer-incharge, (for payment purpose only weight of
stainless steel members shall be considered excluding fixing
accessories such as nuts, bolts, fasteners etc.).
Providing & fixing glass panes with putty and glazing clips
in steel doors, windows, clerestory windows, all complete with :
10.30.1 4.0 mm thick glass panes Sqm 213.00 999.82 212961.87
Providing and fixing hand rail of approved size by welding etc. to
steel ladder railing, balcony railing, staircase railing and similar
works, including applying priming coat of approved steel
primer. M.S. tube
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand
: 4 graded stone aggregate) finished with a floating coat of neat
cement, including cement slurry, but excluding the cost of
nosing of steps etc. complete.
74 11.3.1 40 mm thick with 20 mm nominal size stone aggregate Sqm 5.00 579.50 2897.49
Chequerred precast cement concrete tiles 22 mm thick in
footpath & courtyard, jointed with neat cement slurry mixed
with pigment to match the shade of tiles, including rubbing and
cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4
(1 cement: 4 coarse sand). Ordinary
cement without any pigment.
Marble stone flooring with 18 mm thick marble stone, as per
sample of marble approved by Engineer-in-charge, over 20
mm (average) thick base of cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with grey cement slurry, including
rubbing and polishing complete with : Note : Qty. shall be
executed in marble strips of width upto 50mm.
11.23.5 Udaipur green marble Sqm 20.00 2233.36 44667.11
11.24 Extra for pre finished nosing to treads of steps of marble stone. Rm 394.00 630.86 248557.22
Extra for marble stone flooring in treads of steps and risers using
single length up to 2.00 metre.
Providing and laying Vitrified tiles in floor in different sizes
(thickness to be specified by the manufacturer) with water
absorption less than 0.08% and conforming to IS:15622, of
approved brand & manufacturer, in all colours and shade, laid on
20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)
77 11.41A jointing with grey cement slurry @3.3 kg/sqm including grouting
the joints with white cement and matching pigments etc. The tiles
must be cut with the zero chipping diamond cutter only . Laying
of tiles will be done with the notch trowel, plier, wedge, clips of
required thickness, leveling system and rubber mallet for placing
the tiles gently and easily.
11.41A.1 Double charge vitrified tile polished finish of size
Providing and laying Vitrified tiles in different sizes (thickness to
be specified by manufacturer), with water absorption less than
0.08 % and conforming to I.S. 15622, of approved make, in all
78 11.46 colours & shade, in skirting, riser of steps, over 12 mm thick bed
of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with
grey cement slurry @ 3.3 kg/ sqm including grouting the joint
with white cement & matching pigments
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and laying rectified Glazed Ceramic floor tiles of size
300x300 mm or more (thickness to be specified by the
manufacturer), of 1st quality conforming to IS : 15622, of
approved make, in colours White, Ivory, Grey, Fume Red
Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4
Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm
including grouting the joints with white cement and matching
pigments etc., complete.
Providing and laying machine cut, mirror polished, Italian Marble
stone flooring laid in required pattern in linear portion of the
building all complete as per architectural drawings, with 18 mm
thick stone slab laid over 20 mm (average) thick base of cement
80 11.51 mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white
cement slurry @ 4.4 kg/sqm including pointing with white cement
slurry admixed with pigment to match the marble shade including
rubbing, curing and polishing etc. all complete as specified and
as directed by the Engineer-in-Charge.
18 mm thick Italian Marble stone slab, Perlato, Rosso verona,
Fire Red or Dark Emperadore etc.
Providing and laying Polished Granite stone flooring in required
design and patterns, in linear as well as curvilinear portions of
the building all complete as per the architectural drawings with
18 mm thick stone slab over 20 mm (average) thick base of
81 11.56 cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed
with cement slurry and pointing with white cement slurry admixed
with pigment of matching shade including rubbing, curing and
polishing etc. all complete as specified and as directed by the
Engineer-in-Charge.
Polished Granite stone slab colour of Black, Cherry/Ruby
Red or equivalent
Polished Granite stone slab of all colour and texture except
Black, Cherry/Ruby Red
Providing and fixing precoated galvanised iron profile sheets
(size, shape and pitch of corrugation as approved by Engineer-in-
charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc
coating 120 grams per sqm as per IS: 277, in 240 mpa steel
grade, 5-7 microns epoxy primer on both side of the sheet
and polyester top coat 15-18 microns. Sheet should have
protective guard film of 25 microns minimum to avoid
scratches during transportation and should be supplied in single
length upto 12 metre or as desired by Engineer-in-charge. The
sheet shall be fixed using self drilling /self tapping screws of size
(5.5x 55 mm) with EPDM seal, complete upto any pitch in
horizontal/ vertical or curved surfaces, excluding the cost of
purlins, rafters and trusses and including cutting to size and
shape wherever required.
Providing ridges or hips of width 60 cm overall width plain
G.S. sheet fixed with polymer coated J or L hooks, bolts and
nuts 8 mm dia G.I. limpet and bitumen washers complete
0.80 mm thick with zinc coating not less than 275 gm/m²
12.4.1 0.80 mm thick with zinc coating not less than 275 gm/m² Rm 28.00 874.19 24477.38
Providing and fixing 15 cm wide, 45 cm overall semi-
circular plain G.S. sheet gutter with iron brackets 40x3mm size,
84 12.7.1 bolts, nuts and washers etc., including making necessary Rm 30.00 863.24 25897.20
connections with rain water pipes complete.
0.80 mm thick with zinc coating not less than 275 gm/m²
Providing and fixing tiled false ceiling of specified materials of
size 595x595 mm in true horizontal level, suspended on inter
locking metal grid of hot dipped galvanized steel sections (
galvanized @ 120 grams/ sqm, both side inclusive) consisting of
main "T" runner with suitably spaced joints to get required length
and of size 24x38 mm made from 0.30 mm thick (minimum)
sheet, spaced at 1200 mm center to center and cross "T" of size
24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm
long spaced between main "T" at 600 mm center to center to
form a grid of 1200x600 mm and secondary cross "T" of length
600 mm and size 24x25 mm made of 0.30 mm thick (minimum)
sheet to be interlocked at middle of the 1200x600 mm panel to
form grids of 600x600 mm and wall angle of size 24x24x0.3 mm
and laying false ceiling tiles of approved texture in the grid
including, required cutting/making, opening for services like
diffusers, grills, light fittings, fixtures, smoke detectors etc. Main
"T" runners to be suspended from ceiling using GI slotted cleats
of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia
and 50 mm long dash fasteners, 4 mm GI adjustable rods with
galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced
at 1200 mm center to center along main T, bottom exposed width
of 24 mm of all T-sections shall be pre-painted with polyester
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
GI Metal Ceiling Lay in perforated Tegular edge global white
color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop;
made of GI sheet having galvanizing of 100 gms/sqm (both sides
inclusive) and 20% perforationarea with 1.8 mm dia holes and
12.52.2 having NRC (Noise Reduction Coefficient ) of 0.5, electro Sqm 2400.00 1856.79 4456290.30
statically polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending and
perforation, and backed with a black Glass fiber acoustical
Providing and fixing false ceiling at all height including providing
and fixing of frame work made of special sections, power
pressed from M.S. sheets and galvanized with zinc coating of
120 gms/sqm (both side inclusive) as per IS : 277 and consisting
of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of
27 mm and 37mm, at 1200 mm centre to centre, one flange fixed
to the ceiling with dash fastener 12.5 mm dia x 50mm long with
6mm dia bolts, other flange of cleat fixed to the angle hangers of
25x10x0.50 mm of required length with nuts & bolts of required
size and other end of angle hanger fixed with intermediate G.I.
channels 45x15x0.9 mm running at the spacing of 1200 mm
12.45 centre to centre, to which the ceiling section 0.5 mm thick bottom
wedge of 80 mm with tapered flanges of 26 mm each having lips
of 10.5 mm, at 450 mm centre to centre, shall be fixed in a
direction perpendicular to G.I. intermediate channel with
connecting clips made out of 2.64 mm dia x 230 mm long G.I.
wire at every junction, including fixing perimeter channels 0.5
mm thick 27 mm high having flanges of 20 mm and 30 mm long,
the perimeter of ceiling fixed to wall/partition with the help of rawl
plugs at 450 mm centre, with 25mm long dry wall screws @ 230
mm interval, including fixing of gypsum board to ceiling section
and perimeter channel with the help of dry wall screws of size
12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 350.00 1382.82 483987.58
85 13.1 12 mm cement plaster of mix
15 mm cement plaster on rough side of single or half brick
87 13.16 6 mm cement plaster of mix
Providing and applying white cement based putty of average
thickness 1 mm, of approved brand and manufacturer, over the
plastered wall surface to prepare the surface even and smooth
Distempering with 1st quality acrylic distemper (ready mixed)
having VOC content less than 50 gms/litre, of approved
manufacturer, of required shade and colour
complete, as per manufacturer’s specification.
13.42.1 Two or more coats on new work Sqm 796.00 98.62 78502.38
Applying one coat of water thinnable cement primer of
approved brand and manufacture on wall surface :
13.43.1 Water thinnable cement primer Sqm 32478.18 68.53 2225719.58
Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade:
New work (Two or more coats applied @ 1.43 ltr/10 sqm
13.47.1 over and including priming coat of exterior primer applied @ 2.20 Sqm 7958.42 172.63 1373835.36
92 13.50 Applying priming coat:
With ready mixed pink or Grey primer of approved brand and
manufacture on wood work (hard and soft wood)
With ready mixed red oxide zinc chromate primer of
93 13.50.3 approved brand and manufacture on steel galvanised iron/ Sqm 642.29 59.01 37903.44
Finishing with Epoxy paint (two or more coats) at all
locations prepared and applied as per manufacturer's
specifications including appropriate priming coat,
preparation of surface, etc. complete. On steel work.
Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade :
13.61.1 Two or more coats on new work Sqm 973.95 139.77 136129.76
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Washed stone grit plaster on exterior walls height upto 10 metre
above ground level, in two layers, under layer 12 mm cement
plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer
with scratching tool, applying cement slurry on the under layer @
2 Kg of cement per square metre, top layer 15 mm cement
96 13.72 plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 Sqm 240.00 1047.83 251478.96
mm nominal size), in panels with groove all around as per
approved pattern, including scrubbing and washing the top layer
with brushes and water to expose the stone chippings ,complete
as per specification and direction of Engineer-in-charge
(payment for providing grooves shall be made separately).
Wall painting with premium acrylic emulsion paint of interior
grade, having VOC (Volatile Organic Compound ) content less
97 13.83 than 50 grams/ litre of approved brand and manufacture, Sqm 19264.00 129.24 2489758.63
including applying additional coats wherever required to achieve
even shade and colour
13.83.2 Two coats
K Dismantling & Demolishing
Demolishing R.C.C. work manually/ by mechanical means
including stacking of steel bars and disposal of unserviceable
material within 50 metres lead as per direction of Engineer - in-
Demolishing brick work manually/ by mechanical means
including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead as per direction of
Engineer-in-charge.
15.7.4 In cement mortar Cum 45.00 1796.39 80837.65
Dismantling cement asbestos or other hard board ceiling or
100 15.41 partition walls including stacking of serviceable materials and Sqm 120.00 49.44 5933.21
disposal of unserviceable materials within 50 metres lead.
L Water Proofing
Providing and laying water proofing treatment in sunken
portion of WCs, bathroom etc., by applying cement slurry mixed
with water proofing cement compound consisting of
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with
water proofing cement compound @ 0.253 kg/ sqm. This layer
will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed
with water proofing cement compound @ 0.126 kg/sqm. This
layer will be allowed to air cure for 4 hours
followed with water curing for 48 hours.
The rate includes preparation of surface, treatment and
sealing of all joints, corners, junctions of pipes and Sqm 519.98 549.30 285625.42
masonry with polymer mixed slurry.
Providing and laying water proofing treatment on roofs of slabs
by applying cement slurry mixed with water proofing cement
compound consisting of applying: (a) after surface
preparation, first layer of slurry of cement @
0.488 kg/sqm mixed with water proofing cement
compound @ 0.253 kg/sqm.
(b) laying second layer of Fibre glass cloth when the first
layer is still green. Overlaps of joints of fibre cloth should not be
less than 10 cm.
(c) third layer of 1.5 mm thickness consisting of slurry of cement
@ 1.289 kg/sqm mixed with water proofing cement
compound @ 0.670 kg/sqm and coarse sand @
1.289 kg/sqm. This will be allowed to air cure for 4 hours
followed by water curing for 48 hours. The entire
treatment will be taken upto 30 cm on parapet wall and
tucked into groove in parapet all around.
(d) fourth and final layer of brick tiling with cement mortar (which
will be paid for separately. For the purpose of measurement Sqm 1286.95 622.62 801274.78
the entire treated surface will be measured.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and laying integral cement based water
proofing treatment including preparation of surface as
required for treatment of roofs, balconies, terraces etc
consisting of following operations:
a) Applying a slurry coat of neat cement using 2.75 kg/sqm
of cement admixed with water proofing compound conforming to
IS. 2645 and approved by Engineer-in- charge over the RCC
slab including adjoining walls upto 300 mm height including
cleaning the surface before treatment.
b) Laying brick bats with mortar using broken bricks/brick bats 25
mm to 115 mm size with 50% of cement mortar 1:5 (1 cement :
5 coarse sand) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge
over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5
coarse sand ) admixed with water proofing compound
conforming to IS : 2645 and approved by Engineer-in-charge
to required slope and treating similarly the adjoining walls upto
300 mm height including rounding of junctions of walls and slabs.
c) After two days of proper curing applying a second coat of
cement slurry using 2.75 kg/ sqm of cement admixed with
water proofing compound conforming to IS : 2645 and
approved by Engineerin-charge.
d) Finishing the surface with 20 mm thick jointless cement mortar
of mix 1:4 (1 cement :4 coarse sand) admixed with water
proofing compound conforming to IS : 2645 and approved
by Engineerin-charge including laying glass fibre cloth of
approved quality in top layer of plaster and finally finishing the
surface with trowel with neat cement slurry and making pattern
of 300x300 mm square 3 mm deep.
e) The whole terrace so finished shall be flooded with water
for a minimum period of two weeks for curing and for final
test.“All above operations to be done in order and as directed
and specified by the Engineer-in-Charge :
With average thickness of 120 mm and minimum
thickness at khurra as 65 mm.
Making khurras 45x45 cm with average minimum thickness of 5
cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m
x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1
cement : 3 coarse sand) and a coat of neat cement, rounding the
edges and making and finishing the outlet complete.
105 22.14 Grading roof for water proofing treatment with
Cement concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 20mm nominal size)
Providing and applying integral crystalline slurry of
hydrophilic in nature for waterproofing treatment to the RCC
structures like retaining walls of the basement, water tanks, roof
slabs, podiums, reservior, sewage & water treatment plant,
tunnels / subway and bridge deck etc., prepared by mixing
in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts
water) for vertical surfaces and 3 : 1 (3 parts integral crystalline
slurry : 1 part water) for horizontal surfaces and applying the
same from negative (internal) side with the help of synthetic
fiber brush. The material shall meet the requirements as
specified in ACI- 212-3R-2010 i.e by reducing permeability of
concrete by more than 90% compared with control concrete
as per DIN 1048 and resistant to 16 bar hydrostatic pressure on
negative side. The crystalline slurry shall be capable of self-
healing of cracks up to a width of 0.50mm. The work shall be
carried out all complete as per specification and the direction
of the engineer-in-charge. The product performance shall
carry guarantee for 10 years against any leakage.
22.23.1 For vertical surface two coats @ 0.70 kg per sqm Sqm 55.00 431.97 23758.11
22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 47.00 331.22 15567.24
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and laying in situ five course water proofing treatment
with APP (Atactic Polypropylene) modified Polymeric
memberane over roof consisting of first coat of bitumen primer
@ 0.40 litre per sqm, 2nd & 4th courses of bonding material @
1.20 kg/sqm, which shall consist of blown type bitumen of grade
85/25 conforming to IS : 702, 3rd layer of roofing membrane APP
modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm
weight consisting of five layers prefabricated with centre core as
107 14.87 100 micron HMHDPE film sandwiched on both sides with Sqm 100.00 483.59 48358.88
polymeric mix and the polymeric mix is protected on both side
with 20 micron HMHDPE film. 5th, the top most layer shall be
finished with brick tiles of class designation 10 grouted with
cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2%
integral water proofing compound by weight of cement over a 12
mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for
Providing and laying 60mm thick factory made cement
concrete interlocking paver block of M-30 grade made by block
making machine with strong vibratory compaction, of approved
108 16.68 size, design & shape, laid in required colour and pattern over Sqm 1140.00 1011.20 1152766.06
and including 50mm thick compacted bed of coarse sand,
filling the joints with line sand etc. all complete as per the
direction of Engineer-in-charge.
Providing and laying at or near ground level factory made kerb
stone of M-25 grade cement concrete in position to the required
line, level and curvature, jointed with cement mortar 1:3 (1
cement: 3 coarse sand), including making joints with or without
grooves (thickness of joints except at sharp curve shall not to
more than 5mm), including making drainage opening
wherever required complete etc. as per Providing and laying
at or near ground level factory made kerb stone of M-25 grade
cement concrete in position to the required line, level and
curvature, jointed with cement mortar 1:3 (1 cement: 3
coarse sand), including making joints with or without grooves
(thickness of joints except at sharp curve shall not to more
than 5mm), including making drainage opening wherever
required complete etc. as per
Providing and laying C.C. pavement of mix M-25 with ready
mixed concrete from batching plant. The ready mixed
concrete shall be laid and finished with screed board vibrator
, vacuum dewatering process and finally finished by
floating, brooming with wire brush etc. complete as per
specifications and directions of Engineer-incharge. (The panel
shuttering work shall be paid for separately).
(Note:- Cement content considered in this item is @ 330 kg/cum.
Excess/less cement used as per design mix is payable/
recoverable separately).
Deduct for using of M-20 grade concrete instead of M-25
grade concrete in C.C. pavement.
Providing and fixing pre-moulded joint filler in expansion joints of
RCC roads / CC pavements after making the joints dust free with
high pressure air jet cleaners, all complete as per direction of the
Engineer-in-Charge. (Pre-moulded joint fillers shall be made of
hot sealing compound impregnated fibre board having
more than 35%, conforming to IS:1838 for fibre board and IS:
for hot sealing bitumen compound grade A.)
N Aluminium Work
Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard tubular
sections/ appropriate Z sections and other sections of approved
make conforming to IS: 733 and IS: 1285, fixing with dash
fasteners of required dia and size, including necessary filling up
the gaps at junctions, i.e. at top, bottom and sides with required
113 21.1 EPDM rubber/ neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap
beading for glazing / paneling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling and dash
fasteners to be paid for separately) :
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
21.1.1 For fixed portion
Powder coated aluminium (minimum thickness of powder coating
For shutters of doors, windows & ventilators including providing
and fixing hinges/ pivots and making provision for fixing of fittings
wherever required including the cost of EPDM rubber / neoprene
gasket required (Fittings shall be paid for separately)
Powder coated aluminium (minimum thickness of powder coating
Providing and fixing glazing in aluminium door, window,
ventilator shutters and partitions etc. with EPDM rubber /
114 21.3 neoprene gasket etc. complete as per the architectural drawings
and the directions of engineer-in-charge . (Cost of aluminium
snap beading shall be paid in basic item):
With float glass panes of 8 mm thickness (weight not less than
Filling the gap in between aluminium frame & adjacent RCC/
Brick/ Stone work by providing weather silicon sealant over
backer rod of approved quality as per architectural drawings and
direction of Engineer-in-charge complete.
21.8.1 Upto 5mm depth and 5 mm width Sqm 2602.20 90.65 235879.87
Providing and fixing stainless steel (SS 304 grade) adjustable
116 21.11 windows stays of approved quality with necessary stainless steel
screws etc. to the side hung windows as per direction of
Engineer in-charge complete.
Providing and fixing Brass 100mm mortice latch and lock with 6
levers without pair of handles (best make of approved quality) for
117 21.13 aluminium doors including necessary cutting and making good Each 93.00 478.01 44454.61
O STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL
Providing and fixing 12mm thick frameless toughened glass
door shutter of approved brand and manufacture, including
and fixing top & bottom pivot & double acting hydraulic floor
type fixing arrangement and making necessary holes etc. for
required door fittings, all complete as per direction of Engineer in
(Door handle, lock and stopper etc. to be paid separately)
Providing and supplying aluminium extruded tubular and other
aluminium sections as per the architectural drawings and
approved shop drawings , the aluminium quality as per grade
6063 T5 or T6 as per BS 1474,including super durable powder
coating of 60-80 microns conforming to AAMA 2604 of required
119 25.1 colour and shade as approved by the Engineer-in-Charge. ( The Kg 2500.00 393.90 984748.71
item includes cost of material such as cleats, sleeves, screws
etc. necessary for fabrication of extruded aluminium frame work.
Nothing extra shall be paid on this account). The weight of
aluminium extruded section shall be taken for purpose of
Designing, fabricating, testing, protection, installing and fixing in
position semi (grid) unitized system of structural glazing (with
open joints) for linear as well as curvilinear portions of the
building for all heights and all levels, including:
(a) Structural analysis & design and preparation of shop
drawings for the specified design loads conforming to IS 875 part
III (the system must passed the proof test at 1.5 times design
pressure without any failure), including functional design of the
aluminum sections for fixing glazing panels of various
thicknesses, aluminium cleats, sleeves and splice plates etc.
gaskets, screws, toggles, nuts, bolts, clamps etc., structural and
weather silicone sealants, flashings, fire stop (barrier)- cum-
smoke seals, microwave cured EPDM gaskets for water
tightness, pressure equalisation & drainage and protection
against fire hazard including:
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
(b) Fabricating and supplying serrated M.S. hot dip galvanised /
Aluminium alloy of 6005 T5 brackets of required sizes, sections
and profiles etc. to accommodate 3 Dimentional movement
for achieving perfect verticality and fixing structural glazing
system rigidly to the RCC/ masonry/structural steel framework of
building structure using stainless steel anchor fasteners/
bolts, nylon seperator to prevent bimetallic contacts with nuts
and washers etc. of stainless steel grade 316, of the required
capacity and in required numbers.
(c) Providing and filling, two part pump filled, structural silicone
sealant and one part weather silicone sealant compatible with
the structural silicone sealant of required bite size in a clean
and controlled factory / work shop environment, including double
sided spacer tape, setting blocks and backer rod, all of approved
grade, brand and manufacture, as per the approved
sealant design, within and all around the perimeter for
(d) Providing and fixing in position flashings of solid aluminium
sheet 1 mm thick and of sizes, shapes and profiles, as required
as per the site conditions, to seal the gap between the building
structure and all its interfaces with curtain glazing to make it
(e) Making provision for drainage of moisture/ water that enters
the curtain glazing system to make it watertight, by incorporating
principles of pressure equalization, providing suitable gutter
profiles at bottom (if required), making necessary holes of
required sizes and of required numbers etc. complete. This item
includes cost of all inputs of designing, labour for fabricating and
installation of aluminium grid, installation of glazed units, T&P,
scaffolding and other incidental charges including wastages etc.,
enabling temporary structures and services, cranes or cradles
etc. as described above and as specified. The item includes the
cost of getting all the structural and functional design including
shop drawings checked by a structural designer, dully approved
by Engineer-in-charge. The item also includes the cost of all
mock ups at site, cost of all samples of the individual
components for testing in an approved laboratory, field tests on
the assembled working structural glazing as specified, cleaning
and protection till the handing over of the building for occupation.
In the end, the Contractor shall provide a water tight structural
glazing having all the performance characteristics etc. all
complete as required, as per the Architectural drawings, as per
item description, as specified, as per the approved shop
drawings and as directed by the Engineer- in-Charge.
Providing, assembling and supplying vision glass panels (IGUs)
comprising of hermetically-sealed 6-12- 6 mm insulated glass
(double glazed) vision panel units of size and shape as required
and specified, comprising of an outer heat strengthened float
glass 6mm thick, of approved colour and shade with reflective
soft coating on surface # 2 of approved colour and shade, an
inner Heat strengthned clear float glass 6mm thick, spacer tube
12mm wide, dessicants, including primary seal and secondary
seal (structural silicone sealant) etc. all complete for the required
121 25.3 performances, as per the Architectural drawings, as per the
approved shop drawings, as specified and as directed by the
Engineer-in-Charge. The IGUs shall be assembled in the factory/
workshop of the glass processor.
(Payment for fixing of IGU Panels in the curtain glazing is
included in cost of item No.25.2)
For payment, only the actual area of glass on face # 1 of the
glass panels (excluding the areas of the grooves and weather
silicone sealant) provided and fixed in position, shall be
measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with reflective
soft coating on face # 2, + 12mm Airgap + 6mm Heat
Strengthened clear Glass of approved make having properties
as visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10 to 20 %, Sqm 390.00 3591.30 1400605.34
shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2
degree K etc. The properties of performance glass shall be
decided by technical sanctioning authority as per the site
Extra for openable side / top hung vision glass panels (IGUs)
including providing and supplying at site all accessories and
hardwares for the openable panels as specified and of the
approved make such as heavy duty stainless steel friction
122 25.4 hinges, min 4 -point cremone locking sets with stainless steel Sqm 60.00 3518.51 211110.77
plates, handles, buffers etc. including necessary stainless steel
screws/ fasteners, nuts, bolts, washers etc. all complete as per
the Architectural drawings, as per the approved shop drawings,
as specified and as directed by the Engineer- in Charge
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
P New Technologies and Materials
Providing and fixing factory made single extruded WPC (Wood
Polymer Composite) solid door/window/Ceosetory windows &
other Frames/Chowkhat comprising of virgin PVC polymer of K
value 58- 60 (Suspension Grade), calcium carbonate and natural
fibers (wood powder/ rice husk/wheat husk) and non toxic
additives (maximum toxicity index of 12 for 100 gms) fabricated
with miter joints after applying PVC solvent cement and screwed
with full body threaded star headed SS screws having minimum
123 26.86 frame density of 750 kg/ cum, screw withdrawal strength of 2200
N (Face) & 1100 N (Edge), minimum compressive strength of 58
N/mm2, modulus of elasticity 900 N/mm2 and resistance to
spread of flame of Class A category with property of being
termite/borer proof, water/moisture proof and fire retardant and
fixed in position with M.S hold fast/lugs/SS dash fasteners of
required dia and length complete as per direction of Engineer-In-
Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid
for separately).
Note: For WPC solid door/window frames, minus 5mm tolerance
in dimensions i.e depth and width of profile shall be acceptable.
Variation in profile dimensions on plus side shall be acceptable
but no extra payment on this account shall be made.
Providing and fixing factory made single extruded WPC (Wood
Polymer Composite) solid decorative type flush door shutter of
required size comprising of virgin polymer of K value 58-60
(Suspension Grade), calcium carbonate and natural fibers (wood
powder/ rice husk/wheat husk) and non toxic additives
(maximum toxicity index of 12 for 100 gms) having minimum
density of 650 kg/cum and screw withdrawal strength of 1800 N
(Face) & 900 N (Edge), minimum compressive strength 50 N/
mm2, modulus of elasticity 850 N/mm2 and resistance to spread
of flame of Class A category with property of being termite/ borer
proof, water/moisture proof and fire retardant. WPC to be
laminated with PVC foil of minimum 14 microns thick of approved
design pasted with hot melt adhesive on both faces of shutter
and fixing with stainless steel butt hinges of required size with
necessary full body threaded star headed counter sunk S.S
screws, all as per direction of Engineer-In- Charge.
(Note: stainless steel butt hinges and necessary S.S screws
shall be paid separately)
Providing and fixing 15 mm thick false ceiling tiles at all heights
with integral densified calcium silicate reinforced with fibre and
natural filler false ceiling tiles of Size 595x595 mm of approved
texture, design
and patterns having NRC (Noise Reduction coefficient) of 0.50
(minimum) as per IS 8225:1987, Light reflectance of 85%
125 26.25 (minimum). Non combustible as per BS:476 (part-4), fire Sqm 40.00 1508.82 60352.91
performance as per BS:476 (part 6 &7), humidity resistance of
100%, thermal conductivity
< 0.043 W/m K as per ASTM 518:1991,in true horizontal level on
the existing frame work consisting of T-sections and Lsections
suitably fixed according to tile size as per direction of Engineer-in-
Q Non-Schedule Items - Civil & Misc.
Providing signage viz display/name plate and like of required
size made out of 20 guage thick stainless steel (304
grade) including engraved subject matter, message (
Odia/Hindi/English or Trilingual), symbols, borders and logo
etc. The engraved letter, borders etc. to be furnished with
paint etc. of reqyured colour scheme and the plate to be fixed
to wooden/wall surface with 25mm long stainless steel
spacer/stud all complete as per direction of Engineer in Charge.
Providing & fixing G.I. chicken wire mesh of nominal size upto
20mm having 24 gauge thick with G.I. nails etc. to wall
surface of dissmilar material viz RCC and brick work etc.all
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Diluting and injecting chemical emulsion for POST-
CONSTRUCTIONAL anti-termite treatment (excluding the cost of
chemical emulsion) Along external wall where the apron is not
provided using chemical emulsion @ 7.5 litres / sqm of the
vertical surface of the substructure to a depth of 300mm
including excavation channel along the wall & rodding etc.
complete including Supplying chemical emulsion in sealed
containers including delivery as specified.
Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Sqm 3358.90 129.80 435985.22
Providing and laying weather and Ultravoilet Resistant, Water
Repellent, Dust, Dirt and Stain Resistant, Fungus and Algae
Resistant natural none pigmented crushed granite Chips (100%
natural crushed Granite chips/powder) of approved make with
final coat of texture with stone chips (attainable thickness: 0.70 to
0.90mm to offer grooved finish) applied with Spray over a coat of
129 MR 4 texture without chips (attainable thickness: 0.50 to 0.70mm to Sqm 3876.00 1239.15 4802945.40
offer smooth surface as base coat) over a repair check with
exterior grade cement mixed with acrylic primer over a coat of
acrylic primer mixed with wall sealer in the ratio of 1:1 complete
as approved by Engineer-in-charge. Finally one coat of water
base acrylic protection coat applied with roller and brush to make
surface streak resistance.
Providing and placing various wooden & Brass statue and wall
pannel of approved design and colour shade having the
130 MR 5 minimum height of 183cm including all cost of transportation and Each 2.00 275600.00 551200.00
labour, complete as direction of Engineer-In-Charge-74" Large
Wooden Statue 188cm height X 157.7cm Width X 27cm depth
Providing, Installing and testing of customized stainless steel
letter and logos with led lighting works ( Odia/Hindi/English or
Trilingual), symbols, borders and logo etc. The engraved
131 MR 6 letter, borders etc. to be furnished with paint etc. of reqyured Sqft 80.00 1069.50 85560.00
colour scheme and the plate to be fixed to wooden/wall surface
with 25mm long stainless steel spacer/stud all complete as per
direction of Engineer in Charge.
Providing and fixing IS : marked stainless steel heavy duty
weight) of required size and shape with stainless steel screws
etc. complete :
SUB-TOTAL 163643475.35
ELECTRICAL WORKS
1 SH-I (WIRING)
Wiring for light point/ fan point/ exhaust fan point/ call bell point
with 1.5 sq.mm FRLS PVC insulated copper conductor single
core cable in surface/ recessed steel conduit, with modular
switch, modular plate, suitable GI box and earthing the point with
1.5 sq.mm. FRLS PVC insulated copper conductor single core
cable etc as required.
Wiring for twin control light point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface /
recessed steel conduit, 2 way modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm. FRLS
PVC insulated copper conductor single core cable etc. as
Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated
copper conductor single core cable in surface/ recessed steel
conduit along with 1 No 4 sq. mm FR PVC insulated copper
conductor single core cable for loop earthing as required.
Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated
copper conductor single core cable in surface/ recessed steel
conduit along with 2 Nos 4 sq. mm FR PVC insulated copper
conductor single core cable for loop earthing as required.
Wiring for circuit/ sub main wiring along with earth wire with the
following sizes of FR PVC insulated copper conductor, single
core cable in surface/ recessed steel conduit as required.
1.5.2 1.7.4 ii)2 X 6 sq. mm + 1 X 6 sq. mm earth wire (Type-II submain ) Mtr 750.00 626.28 469712.78
iii)2 X 10 sq. mm + 1 X 6 sq. mm earth wire (Dormitory Submain)
Supplying and drawing following pair 0.5 mm dia FRLS PVC
insulated annealed copper conductor, unarmored telephone
cable in the existing surface/ recessed steel/ PVC conduit/Floor
raceways complete as required.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm
solid copper conductor PE insulated, shielded with fine tinned
copper braid and protected with PVC sheath in the existing
surface/ recessed steel/ PVC conduit as required
Supplying and fixing of following sizes of steel conduit along with
accessories in surface/recess including painting in case of
1.8 surface conduit, or cutting the wall and making good the same in
case of recessed conduit as required. ( For LAN, Telephone, TV)
Supplying and fixing following modular switch/ socket on the
1.9 existing modular plate & switch box including connections but
excluding modular plate etc. as required.
1.9.1 1.24.6 Telephone socket outlet Each 40.00 157.37 6294.74
1.9.2 1.24.7 TV antenna socket outlet Each 120.00 157.37 18884.21
1.9.3 MR 25 amp socket outlet Each 80.00 663.00 53040.00
1.9.4 MR 25 Amps AC Starter Each 80.00 534.00 42720.00
Supplying and fixing following size/ modules, GI box along with
1.1 modular base & cover plate for modular switches in recess etc
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providing and
1.11 1.31 fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps Each 80.00 507.19 40575.53
modular switch, connection etc. as required. (For light plugs to
be used in non residential buildings).
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providing and
fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16
amps modular switch, connection etc. as required.
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providng and
1.13 1.56 fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A Each 160.00 718.79 115006.53
modular switch, connections etc. as required. (For light plugs to
be used in non residential buildings)
Supplying and fixing 3 pin, 5 amp ceiling rose on the existing
1.14 1.33 junction box/ wooden block including connection etc as required. Each 300.00 92.51 27752.13
Supplying and fixing call bell/ buzzer suitable for single phase,
230 volts, complete as required.
Supplying and fixing PVC batten/ angle holder including
connection etc. as required.
2 SH-II (FAN & FITTINGS)
Supplying,installation,testing and commissioning of energy
efficient T8 LED batten luminaries with 20 watt LED lamp
2.1 MR separately, made of aluminium die cast housing complete with Each 320.00 1632.00 522240.00
electronic driver and all other accessories suitable for operation
on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of energy
efficient surface/recess mounted 15 watt LED downlight having
lumen output not less than 100 lumen/watt,surface/recess
2.2 MR mounted luminaire having extruded diecast aluminium with an Each 70.00 3261.00 228270.00
efficient diffuser complete with electronic driver i/c
connectionsuitable for operation on 230v,50 Hz supply etc
complete as required.
Supplying,installation,testing and commissioning of LED 10 watt
mirror light fitting With extruded polycarbonate housing, High
optically efficient diffuser, above wash basin complete with all
accessories etc. directly on wall, including connection with 1.5
sq. mm FRLS PVC insulated, copper conductor, single core
cable and earthing etc. as required.
Supplying,installation,testing and commissioning on Surface/wall
2.4 MR mounted type 10 watt bulk head LED light fitting complete with Each 50.00 2037.00 101850.00
all accessories as required.
Supplying,installation,testing and commissioning of decorative
2.5 MR LED wall light fitting i/c one number 10 watt LED bulb B22 base
type suitable for 230 volts, 50 Hz AC supply as required.
Supplying, installation of 300 mm sweep 900 RPM heavy duty
exhaust fan with metal louver shutter of suitable size in the
existing opening suitable for 230 V 50 Hz AC supply connection,
testing, commissioning etc. as reqd.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supply, Installation, Testing and Commissioning of 1200 mm
sweep, BEE 5 star rated, ceiling fan with Brush Less Direct
Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30
cm long down rod, 2 nos. canopies, shackle kit, safety rope,
copper winding, Power Factor not less than 0.9, Service Value
(CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350
2.7 19.1 RPM (tolerance as per IS : 374- 2019), THD less than 10%, Each 120.00 2902.81 348337.08
remote or electronic regulator unit for speed control and all
remaining accessories including safety pin, nut bolts, washers,
temperature rise=75 degree C (max.), insulation resistance more
than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC
Supply, earthing etc. complete as required.
Supplying and fixing two module stepped type electronic fan
2.8 1.25 regulator on the existing modular plate & switch box including Each 120.00 392.36 47082.92
connections but excluding modular plate etc. as required.
Supplying,installation,testing and commissioning of energy
efficient surface/recess mounted 6 watt LED downlight having
lumen output not less than 100 lumen/watt,surface/recess
2.90 mounted luminaire having extruded diecast aluminium with an
efficient diffuser complete with electronic driver i/c
connectionsuitable for operation on 230v,50 Hz supply etc
complete as required.
Supplying, installation,testing and commissioning of energy
efficient LED flood light luminaries having wattage not more than
150 watt and lumen output not less than 110 lumen/watt, made
2.10 MR of aluminium die cast housing with IP66 protection complete with Each 10.00 22531.00 225310.00
electronic driver and all other accessories suitable for operation
on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of Energy
efficient surface/recess mounted LED luminaire made up of Die
cast Aluminium of 600 X 600 mm size not less than 36 Watt and
2.11 lumens output 100 lumens/watt, with Highly efficient PMMA
diffusers with electronic driver and all other accessories suitable
for operation on 230 V, 50 Hz supply as required.
3 SH-III(DB & SWITCHGEARS)
Supplying and fixing following way, single pole and neutral, sheet
steel, MCB distribution board, 240 V, on surface/ recess,
3.1 complete with tinned copper bus bar, neutral bus bar, earth bar,
din bar, interconnections, powder painted including earthing etc.
as required. (But without MCB/RCCB/Isolator)
Supplying and fixing following rating, 240/415 volts, "C" curve,
miniature circuit breaker suitable for inductive load of following
poles in the existing MCB DB complete with connections, testing
and commissioning etc. as required.
4 SH-IV (EARTHING)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and eatering pipe of 2.7
metre long etc. with charcoal/ coke and salt as required.
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including
accessories, and providing masonry enclosure with cover plate
having locking arrangement and watering pipe etc. with charcoal/
coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia
G.I. pipe from earth electrode including connection with brass
nut, bolt, spring, washer excavation and re-filling etc. as
Providing and fixing 25 mm X 5 mm copper strip on surface or in
recess for connections etc. as required
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.
4.5 5.11 pipe from earth electrode including connection with G.I. nut, bolt, mtr 25.00 750.69 18767.25
spring, washer excavation and re-filling etc. as required.
Providing and fixing 25mm x 5 mm GI strip on surface or in
recess for earth connection as reqd.
Providing and fixing 6 SWG dia GI wire on surface or in recess
4.7 5.18 for looping earthing along with the existing surface / recess mtr 200.00 44.66 8931.72
conduit / submain / cable as reqd.
Providing and laying earth connection from earth electrode with 6
SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode
including connection with G.I. thimble excavation and re-filling as
Providing and fixing 6 SWG dia G.I. wire on surface or in recess
for loop earthing as required.
Providing, laying and fixing following dia G.I. pipe (medium class)
4.10 in ground complete with G.I. fittings including trenching (75 cm
deep) and re-filling etc as required.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
5 SH-V ( CABLING)
Supplying of following size PVC insulated and PVC sheathed /
5.1 XLPE aluminium conductor armoured power cable of 1.1 kV
grade etc. as required.
Laying of one number PVC insulated and PVC sheathed / XLPE
power cable of 1.1 kV grade of following size direct in ground
including excavation, sand cushioning, protective covering and
refilling the trench etc. as required.
5.2.2 7.1.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 250.00 430.64 107659.13
Laying of one number PVC insulated and PVC sheathed / XLPE
power cable of 1.1 KV grade of following size in the existing
RCC/ HUME/ METAL pipe as required.
5.3.2 7.5.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 50.00 60.61 3030.41
Laying of one number PVC insulated and PVC sheathed / XLPE
5.4 power cable of 1.1 KV grade of following size in the existing
masonry open duct as required.
5.4.2 7.6.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 50.00 47.85 2392.43
Laying and fixing of one number PVC insulated and PVC
5.5 sheathed / XLPE power cable of 1.1 KV grade of following
size on wall surface as required.
5.5.1 7.7.1 i)Upto 35 sq. mm(clamped with 1mm thick saddle) mtr 10.00 58.48 584.82
ii)Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
Supplying and making end termination with brass compression
gland and aluminium lugs for following size of PVC insulated &
PVC sheathed / XLPE aluminium conductor cable of 1.1KV
Providing of set of 4 Nos. 9.5 litres capacity G.I. buckets along
with fire bucket stand suitable 4Nos buckets painted in post
5.7 MR office red colour with prior coat of red -oxide paint and written job 5.00 5180.00 25900.00
with white paint "FIRE" including filling sand etc, as required.
Supplying & storing (at site) of 11 KV grade Rubber Hand Glove
Supplying and Storing (at site) of 11 KV grade Discharge Rod
along with necessary wires etc as reqd
Providig and fixing MV danger notice plate of size 200mm x 150
mm made of mild steel,at least 2mm thick, and vitreous
enameled white on both sides and with inscription in single red
colour on front side as reqd.
6 SH-VI (LIGHTNING ARRESTER)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and eatering pipe of 2.7
metre long etc. with charcoal/ coke and salt as required.
Providing and fixing of lightning conductor finial, made of 25 mm
dia 300 mm long, G.I. tube, having single prong at top, with 85
mm dia 6 mm thick G.I. base plate including holes etc. complete
Jointing copper / G.I. tape (with another copper/ G I tape, base of
6.3 6.4 the finial or any other metallic object) by riveting / nut bolting / Each 100.00 120.15 12015.29
sweating and soldering etc as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or
6.4 6.7 surface of wall for lightning conductor complete as required. (For Mtr 400.00 133.98 53590.32
horizontal run)
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or
6.5 6.8 surface of wall for lightning conductor complete as required. (For Mtr 50.00 209.47 10473.51
Providing and fixing testing joint, made of 20 mm X 3 mm thick
6.6 6.12 G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts Each 10.00 128.66 1286.59
and spring washers etc. complete as required.
Providing and laying G.I. tape 32 mm X 6 mm from earth
electrode directly in ground as required.
7 SH-VII(LT PANELS)
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supplying, installation, testing & commissioning of cubical type
LT Indoor Panel Board for 415V, 3 Phase, 4 Wire, 50 Hz AC
supply system of suitable size fabricated in compartmentalized
design from CRCA sheet steel of 2 mm thick for frame work and
covers, 3mm thick for gland plates i/c cleaning & finishing
complete with 7 tank process for powder coating in approved
7.1 shade, having 300 A capacity extensible type four strip
aluminium bus bars of high conductivity, DMC / SMC bus bar
supports, bottom base channel of MS section not less than 75
mmx 50 mm x 5 mm thick, entire panel shall have a common GI
earth bar 25mm x 5mm at the rear with 2 Nos. earth stud, solid
from main bus bar to switch gears with required size of
aluminium bus bars and control wiring with 2.5 sq. mm. PVC
insulated copper conductor S/C cable, cable alleys, cable gland
plates in two half, i/c providing and fixing of following switchgear
and components complete as required.
1) 125 A, FP, 25 kA, thermo magnetic release type MCCB with
spreader link & ROH - 01 No.
2)1 set of 150/5 A ratio CTs
3)1 Set of LED type indicating lamps(RYB) with 2 Amps SP
MCBs for Instrument Protection
4)Multi Function Meter -1 no
(II) Busbars and their ratings
150 A 4 strip aluminum busbars - 100 % Neutral
1)40 A, DP, MCB 10 kA - 10 Nos
MR 2)1 Phase Energy Meter- 08 Nos job 5.00 95934.00 479670.00
8 SH-VIII(FIRE EXTINGUISHERS)
Supplying, installing, testing and commissioning of 4.5 kG
capacity stored pressure type carbon dioxide type fire
extinuishers made from brand new seamless drawn steel
8.1 MR cylinder as per IS 7285 with ISI mark, fitted with wheel valve as each 10.00 8649.00 86490.00
per IS 3224 with ISI mark, with discharge bend and horn and
complete with initial charge as per IS 15683 with ISI mark and
wall bracket complete as required.
Supplying, installation, testing and commissioning of ABC stored
pressure type Fire extinguishers of 4 KG capacity fitted with
discharge control valve and pressure gauge, filled with mono
ammonium phosphate powder as per EN 3615 approved and
supplied complete with initial charge as per IS: 15683 with ISI
mark and wall bracket complete as required.
Supplying, installation and testing of 2 kG capacity Eco Friendly,
Stored pressure type filled with HFC 134 A ( clean agent fire
extinguishant having Zero Ozone depletion potential ) Clean
8.3 MR Agent Fire Extinguishers with safety seal, pressure guage, each 10.00 12097.00 120970.00
controllable discharge mechanism, helium leak detection tested
and conforming to IS 15683 complete with initial charge as
ADMINISTRATIVE BLOCK
1 SH-I (WIRING)
Wiring for light point/ fan point/ exhaust fan point/ call bell point
with 1.5 sq.mm FRLS PVC insulated copper conductor single
core cable in surface/ recessed steel conduit, with modular
switch, modular plate, suitable GI box and earthing the point with
1.5 sq.mm. FRLS PVC insulated copper conductor single core
cable etc as required.
Wiring for twin control light point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface /
recessed steel conduit, 2 way modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm. FRLS
PVC insulated copper conductor single core cable etc. as
Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated
copper conductor single core cable in surface/ recessed steel
conduit along with 1 No 4 sq. mm FR PVC insulated copper
conductor single core cable for loop earthing as required.
Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated
copper conductor single core cable in surface/ recessed steel
conduit along with 2 Nos 4 sq. mm FR PVC insulated copper
conductor single core cable for loop earthing as required.
Wiring for circuit/ sub main wiring along with earth wire with the
following sizes of FR PVC insulated copper conductor, single
core cable in surface/ recessed steel conduit as required.
1.5.2 1.7.4 ii)2 X 6 sq. mm + 1 X 6 sq. mm earth wire (Type-II submain ) Mtr 500.00 626.28 313141.85
iii)2 X 10 sq. mm + 1 X 6 sq. mm earth wire (Dormitory Submain)
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supplying and drawing following pair 0.5 mm dia FRLS PVC
insulated annealed copper conductor, unarmored telephone
cable in the existing surface/ recessed steel/ PVC conduit/Floor
raceways complete as required.
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm
solid copper conductor PE insulated, shielded with fine tinned
copper braid and protected with PVC sheath in the existing
surface/ recessed steel/ PVC conduit as required
Supplying and fixing of following sizes of steel conduit along with
accessories in surface/recess including painting in case of
1.8 surface conduit, or cutting the wall and making good the same in
case of recessed conduit as required. ( For LAN, Telephone, TV)
Supplying and fixing following modular switch/ socket on the
1.9 existing modular plate & switch box including connections but
excluding modular plate etc. as required.
1.9.1 1.24.6 Telephone socket outlet Each 80.00 157.37 12589.47
1.9.2 1.24.7 TV antenna socket outlet Each 50.00 157.37 7868.42
1.9.3 MR 25 amp socket outlet Each 130.00 663.00 86190.00
1.9.4 MR 25 Amps AC Starter Each 130.00 534.00 69420.00
Supplying and fixing following size/ modules, GI box along with
1.1 modular base & cover plate for modular switches in recess etc
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providing and
1.11 1.31 fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps Each 30.00 507.19 15215.82
modular switch, connection etc. as required. (For light plugs to
be used in non residential buildings).
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providing and
fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16
amps modular switch, connection etc. as required.
Supplying and fixing suitable size GI box with modular plate and
cover in front on surface or in recess, including providng and
1.13 1.56 fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A Each 350.00 718.79 251576.78
modular switch, connections etc. as required. (For light plugs to
be used in non residential buildings)
Supplying and fixing 3 pin, 5 amp ceiling rose on the existing
1.14 1.33 junction box/ wooden block including connection etc as required. Each 250.00 92.51 23126.78
Supplying and fixing call bell/ buzzer suitable for single phase,
230 volts, complete as required.
Supplying and fixing PVC batten/ angle holder including
connection etc. as required.
2 SH-II (FAN & FITTINGS)
Supplying,installation,testing and commissioning of energy
efficient T8 LED batten luminaries with 20 watt LED lamp
2.1 MR separately, made of aluminium die cast housing complete with Each 30.00 1632.00 48960.00
electronic driver and all other accessories suitable for operation
on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of energy
efficient surface/recess mounted 15 watt LED downlight having
lumen output not less than 100 lumen/watt,surface/recess
2.2 MR mounted luminaire having extruded diecast aluminium with an Each 400.00 3261.00 1304400.00
efficient diffuser complete with electronic driver i/c
connectionsuitable for operation on 230v,50 Hz supply etc
complete as required.
Supplying,installation,testing and commissioning of LED 10 watt
mirror light fitting With extruded polycarbonate housing, High
optically efficient diffuser, above wash basin complete with all
accessories etc. directly on wall, including connection with 1.5
sq. mm FRLS PVC insulated, copper conductor, single core
cable and earthing etc. as required.
Supplying,installation,testing and commissioning on Surface/wall
2.4 MR mounted type 10 watt bulk head LED light fitting complete with Each 20.00 2037.00 40740.00
all accessories as required.
Supplying,installation,testing and commissioning of decorative
2.5 MR LED wall light fitting i/c one number 10 watt LED bulb B22 base Each 10.00 1192.00 11920.00
type suitable for 230 volts, 50 Hz AC supply as required.
Supplying, installation of 300 mm sweep 900 RPM heavy duty
exhaust fan with metal louver shutter of suitable size in the
existing opening suitable for 230 V 50 Hz AC supply connection,
testing, commissioning etc. as reqd.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supply, Installation, Testing and Commissioning of 1200 mm
sweep, BEE 5 star rated, ceiling fan with Brush Less Direct
Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30
cm long down rod, 2 nos. canopies, shackle kit, safety rope,
copper winding, Power Factor not less than 0.9, Service Value
(CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350
2.7 19.1 RPM (tolerance as per IS : 374- 2019), THD less than 10%, Each 170.00 2902.81 493477.53
remote or electronic regulator unit for speed control and all
remaining accessories including safety pin, nut bolts, washers,
temperature rise=75 degree C (max.), insulation resistance more
than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC
Supply, earthing etc. complete as required.
Supplying and fixing two module stepped type electronic fan
2.8 1.25 regulator on the existing modular plate & switch box including Each 170.00 392.36 66700.81
connections but excluding modular plate etc. as required.
Supplying,installation,testing and commissioning of energy
efficient surface/recess mounted 6 watt LED downlight having
lumen output not less than 100 lumen/watt,surface/recess
2.90 MR mounted luminaire having extruded diecast aluminium with an Each 150.00 2399.00 359850.00
efficient diffuser complete with electronic driver i/c
connectionsuitable for operation on 230v,50 Hz supply etc
complete as required.
Supplying, installation,testing and commissioning of energy
efficient LED flood light luminaries having wattage not more than
150 watt and lumen output not less than 110 lumen/watt, made
2.10 MR of aluminium die cast housing with IP66 protection complete with Each 4.00 22531.00 90124.00
electronic driver and all other accessories suitable for operation
on 230v,50 Hz supply etc complete as required.
Supplying,installation,testing and commissioning of Energy
efficient surface/recess mounted LED luminaire made up of Die
cast Aluminium of 600 X 600 mm size not less than 36 Watt and
2.11 MR lumens output 100 lumens/watt, with Highly efficient PMMA Each 250.00 5262.00 1315500.00
diffusers with electronic driver and all other accessories suitable
for operation on 230 V, 50 Hz supply as required.
Supplying,installation,testing and commissioning of 7Mtr GI
2.12 MR octagonal pole coplete with Junction box, MCBs, Connector, Each 12.00 35705.00 428460.00
Wire, Including Faundation of Pole as required.
Supplying,installation,testing and commissioning of 45W LED
Street light luminaire Which lumens output 100 lumens/watt,
with electronic driver and all other accessories suitable for
operation on 230 V, 50 Hz supply as required.
Supplying,installation,testing and commissioning of 11Watt LED
Bollards luminaire with electronic driver and all other accessories
suitable for operation on 230 V, 50 Hz supply as required.
3 SH-III(DB & SWITCHGEARS)
Supplying and fixing following way, Horizontal type three pole
and neutral, sheet steel, MCB distribution board, 415 V, on
surface/ recess, complete with tinned copper bus bar, neutral
bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc. as required. (But without
MCB/RCCB/Isolator)
Supplying and fixing of factory made following ways surface/
recess mounting, vertical type, Double Door, 415 volts, Power
distribution board suitable with tripple pole/four pole MCCB as
incomer and tripple MCB outgoing distribution, sheet steel, dust
3.2 protected, duly powder painted, inclusive of 250 amps tinned
copper bus bar, common neutral link, earth bar, din bar for
mounting MCB's (but without MCCB's in incomer and outgoing )
as required.( Note : Vertical type MCB TPDB is normally used
where 3 phase outlets are required.)
Providing and fixing following rating and breaking capacity
3.3 MCCB in existing cubicle panel board/DBs including drilling
holes in cubicle panel, making connections, etc. as required.
Supplying and fixing following rating, 240/415 volts, "C" curve,
miniature circuit breaker suitable for inductive load of following
poles in the existing MCB DB complete with connections, testing
and commissioning etc. as required.
3.4.2 2.10.3 ii) Double pole
4 SH-IV (EARTHING)
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and eatering pipe of 2.7
metre long etc. with charcoal/ coke and salt as required.
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including
accessories, and providing masonry enclosure with cover plate
having locking arrangement and watering pipe etc. with charcoal/
coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia
G.I. pipe from earth electrode including connection with brass
nut, bolt, spring, washer excavation and re-filling etc. as
Providing and fixing 25 mm X 5 mm copper strip on surface or in
recess for connections etc. as required
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.
4.5 5.11 pipe from earth electrode including connection with G.I. nut, bolt, mtr 20.00 750.69 15013.80
spring, washer excavation and re-filling etc. as required.
Providing and fixing 25mm x 5 mm GI strip on surface or in
recess for earth connection as reqd.
Providing and fixing 6 SWG dia GI wire on surface or in recess
4.7 5.18 for looping earthing along with the existing surface / recess mtr 300.00 44.66 13397.58
conduit / submain / cable as reqd.
Providing and laying earth connection from earth electrode with 6
SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode
including connection with G.I. thimble excavation and re-filling as
Providing and fixing 6 SWG dia G.I. wire on surface or in recess
for loop earthing as required.
Providing, laying and fixing following dia G.I. pipe (medium class)
4.10 in ground complete with G.I. fittings including trenching (75 cm
deep) and re-filling etc as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and watering pipe of 2.7
meter long etc. with charcoal/ coke and salt as required.
5 SH-V ( CABLING)
Supplying of following size PVC insulated and PVC sheathed /
5.1 XLPE aluminium conductor armoured power cable of 1.1 kV
grade etc. as required.
5.1.4 MR iv)4 x 16 sq.mm(Wardens Quarters Boys and Girls) Mtrs 150.00 272.00 40800.00
Laying of one number PVC insulated and PVC sheathed / XLPE
power cable of 1.1 kV grade of following size direct in ground
including excavation, sand cushioning, protective covering and
refilling the trench etc. as required.
5.2.2 7.1.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 70.00 430.64 30144.56
Laying of one number PVC insulated and PVC sheathed / XLPE
power cable of 1.1 KV grade of following size in the existing
RCC/ HUME/ METAL pipe as required.
5.3.2 7.5.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 20.00 60.61 1212.16
Laying of one number PVC insulated and PVC sheathed / XLPE
5.4 power cable of 1.1 KV grade of following size in the existing
masonry open duct as required.
5.4.2 7.6.2 ii)Above 35 sq. mm and upto 95 sq. mm mtr 10.00 47.85 478.49
Laying and fixing of one number PVC insulated and PVC
5.5 sheathed / XLPE power cable of 1.1 KV grade of following
size on wall surface as required.
5.5.1 7.7.1 i)Upto 35 sq. mm(clamped with 1mm thick saddle) mtr 10.00 58.48 584.82
ii)Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
Supplying and making end termination with brass compression
gland and aluminium lugs for following size of PVC insulated &
PVC sheathed / XLPE aluminium conductor cable of 1.1KV
Providing of set of 4 Nos. 9.5 litres capacity G.I. buckets along
with fire bucket stand suitable 4Nos buckets painted in post
5.7 MR office red colour with prior coat of red -oxide paint and written job 1.00 5180.00 5180.00
with white paint "FIRE" including filling sand etc, as required.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supplying & storing (at site) of 11 KV grade Rubber Hand Glove
Supplying and Storing (at site) of 11 KV grade Discharge Rod
along with necessary wires etc as reqd
Providig and fixing MV danger notice plate of size 200mm x 150
mm made of mild steel,at least 2mm thick, and vitreous
enameled white on both sides and with inscription in single red
colour on front side as reqd.
6 SH-VI (LIGHTNING ARRESTER)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and eatering pipe of 2.7
metre long etc. with charcoal/ coke and salt as required.
Providing and fixing of lightning conductor finial, made of 25 mm
dia 300 mm long, G.I. tube, having single prong at top, with 85
mm dia 6 mm thick G.I. base plate including holes etc. complete
Jointing copper / G.I. tape (with another copper/ G I tape, base of
6.3 6.4 the finial or any other metallic object) by riveting / nut bolting / Each 30.00 120.15 3604.59
sweating and soldering etc as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or
6.4 6.7 surface of wall for lightning conductor complete as required. (For Mtr 100.00 133.98 13397.58
horizontal run)
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or
6.5 6.8 surface of wall for lightning conductor complete as required. (For Mtr 50.00 209.47 10473.51
Providing and fixing testing joint, made of 20 mm X 3 mm thick
6.6 6.12 G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts Each 4.00 128.66 514.64
and spring washers etc. complete as required.
Providing and laying G.I. tape 32 mm X 6 mm from earth
electrode directly in ground as required.
7 SH-VII(LT PANELS)
Supplying, installation, testing & commissioning of cubical type
LT Indoor Main Panel Board for 415V, 3 Phase, 4 Wire, 50 Hz
AC supply system of suitable size fabricated in
compartmentalized design from CRCA sheet steel of 2 mm thick
for frame work and covers, 3mm thick for gland plates i/c
cleaning & finishing complete with 7 tank process for powder
7.1 coating in approved shade, having 300 A capacity extensible
type four strip aluminium bus bars of high conductivity, DMC /
SMC bus bar supports, bottom base channel of MS section not
less than 75 mmx 50 mm x 5 mm thick, entire panel shall have a
common GI earth bar 25mm x 5mm at the rear with 2 Nos. earth
stud, solid connections
from main bus bar to switch gears with required size of
aluminium bus bars and control wiring with 2.5 sq. mm. PVC
insulated copper conductor S/C cable, cable alleys, cable gland
plates in two half, i/c providing and fixing of following switchgear
and components complete as required.
1) 800 A, FP, 50 kA,EDO Type ACB- 01 No.
2)1 set of 800/5 A ratio CTs
3)1 Set of LED type indicating lamps(RYB) with 2 Amps SP
MCBs for Instrument Protection
4)Multi Function Meter -1 no
1)250 A, FP, Change Over Switch- 01 No.
2)1 set of 250/5 A ratio CTs
3)1 Set of LED type indicating lamps(RYB) with 2 Amps SP
MCBs for Instrument Protection
4)Multi Function Meter -1 no
(II) Busbars and their ratings
800 A 4 strip aluminum busbars - 100 % Neutral
250 A 4 strip aluminum busbars - 100 % Neutral
1)400 A, FP, 36 kA thermo magnetic release type MCCB with
spreader link & ROH -2 Nos
2)150 A, FP, 25 kA thermo magnetic release type MCCB with
spreader link & ROH -3 Nos
3)80 A, FP, 25 kA thermo magnetic release type MCCB with
spreader link & ROH -3 Nos
4)63 A, FP, 25 kA thermo magnetic release type MCCB with
spreader link & ROH - 06 Nos
8 SH-VIII(DG SET)
8.1 Supply, installation, testing and commissioning of silent type,
turbo-charged, water cooled 150 kVA DG set with AMF panel
conforming to latest environment protection regulations for
emission and noise level comprising of radiator, governor, multi-
cylinder diesel engine equipped with flywheel etc. having Prime
Power Rating of 150 KVA at 0.8 lagging power factor, 415 volt
50 Hz, 3 phase power at 1500 RPM suitable for 0.85 Load Factor
and consisting of the followings:
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
4 stroke, radiator water cooled, electric start , In line fuel pump
with electronic gonerner (Class A1) of suitable BHP at 1500
RPM suitable for above output of alternator at 40 Degree C, 50%
R/H & at 1000 Meter MSL and conforming to
BS:5514/BS:649/IS:10000, capable of taking 80% block load at
the start and 10% over loading for one hour after 12 hours of
continuous operation. The engine shall be fitted complete with all
the required accessories.
Engine mounted instrument Panel fitted with digital display for
Start-stop switch push button type/ with key
Water temperature indication
Lubrication oil pressure indication
Lubrication oil temperature indication
Battery charging indication
Over speed indication
Low lub. Oil trip indication
Engine Hours indication
Synchronous alternator rated for 150 kVA, 415 Volts at 1500
RPM , 3 phase 50 Hz, AC supply with 0.8 lagging power factor at
40 Degree C. The alternator shall be having SPDP enclosure,
brushless, continuous duty, self-excited and self-regulated
through electronic AVR, IP-23 environment protection,
conforming to IS:4722/ IEC:34/ BS:2613 as ammended upto
date, suitable for tropical conditions and with class 'H' insulation.
Base Frame & Foundation :
Both the engine and alternator shall be mounted on suitable
base frame made of MS channel with necessary reinforcement
with AVM. The DG set is to be installed in the indoor/ outdoor
conditions having existing CC flooring and roofing. Necessary
civil work (Foundation) shall be carried out as per requirement of
the site within the scope of work.
Daily service fuel tank of minimum 300 litre capacity, fabricated
out of 3 mm thick M.S. sheet complete with all standard
accessories and fuel piping between fuel tank and diesel engine
with MS class 'C' pipes of suitable dia. Complete with valves,
level indications & accessories as required as per specifications.
Dry exhaust mainfold with hospital exhaust silencer and without
catalytic convertor.
Starting System
12/24V DC starting system comprising of starter motors: voltage
regulator and arrangement for initial excitation complete with
suitable number and AH of batteries (capacity as per the
recommendation of the OEM). Control Cabling from ATS to DG
Set is included in the scope of work for which nothing extra shall
Accoustic Enclosure
Acoustic and weather proof enclosure with arrangement for fresh
air intake for cooling of the engine & alternator, extraction,
discharging hot air into the atmosphere as per specifications.
Automatic mains failure control including auto by pass panel
suitable for 150 kVA silent type DG set complete with MCCB,
MR Contactor, Timer, Voltage monitoring relays, Auxillary relays, Set 1.00 1933773.00 1933773.00
MCBs, battery charger, control cabling from AMF panel to Diesel
engine etc as per OEM recommendation.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing, fixing, & installation of SUKRANTI 13 Passenger Lift
of 884Kgs, 1 Speed 2 Floors, 2 Stops access sides inlin/thru
type 1(one), In front only.
II.MACHINE & CONTROLLER DETAIL :- Machine Room Less-
Drive System- Micro Processor Based VVVF-Closed Loop,
Control System-Microprocessor Based Simplex Selective
Collective Control With / Without Attendent.
Main Power Supply- AC 3 Phase, 50 Cycles, 415 Volts ±10%,
Light Power Supply- 220 Volts 50Hz LNE
III. SHAFT DETAILS Set 1.00 2047000.00 2047000.00
Shaft Type- Reinforced Cement Concrete With Red Brick
Shaft Width mm X Shaft Depth mm- 2450 X 1800
Overhead mm-- 4200
Pit Depth mm-- 1600
Travel Height (in Meters)= 3.4
Shaft Reduction Channel- Not Required
Shaft Reduction Channel Weight (in Kgs) -- No
Pit Ladder = Yes
IV. CABIN DETAILS
Car Width mm X Car Depth mm-- 1500 X 1400
Providing, fixing, & installation of SUKRANTI 13 Passenger Lift
of 884Kgs, 1 Speed 2 Floors, 2 Stops access sides inlin/thru
type 1(one), In front only.
II.MACHINE & CONTROLLER DETAIL :- Machine Room Less-
Drive System- Micro Processor Based VVVF-Closed Loop,
Control System-Microprocessor Based Simplex Selective
Collective Control With / Without Attendent.
Main Power Supply- AC 3 Phase, 50 Cycles, 415 Volts ±10%,
Light Power Supply- 220 Volts 50Hz LNE
III. SHAFT DETAILS Set 1.00 2265500.00 2265500.00
Shaft Type- Reinforced Cement Concrete With Red Brick
Shaft Width mm X Shaft Depth mm- 2450 X 1800
Overhead mm-- 4200
Pit Depth mm-- 1600
Travel Height (in Meters)= 3.4
Shaft Reduction Channel- Not Required
Shaft Reduction Channel Weight (in Kgs) -- No
Pit Ladder = Yes
IV. CABIN DETAILS
SUB TOTALmm X Car Depth mm-- 1500 X 1400 35213537.42
Supply of modular type Variable Refrigerant Flow/Variable
Refrigerant Volume air cooled Outdoor units suitable for cooling
only, having all hermetically sealed inverter type Scroll
Compressor(s), minimum two compressors for above 14 HP
modules, microprocessor based Controller, top discharge type
condensing unit(s), with R 410 A Refrigerant, vibration isolators,
with suitable foundation etc. with refrigerant-cooled PCB for
better performance complete as required. The unit shall deliver
the rated capacity at AHRI Conditions and work even at 49°C
ambient temperature without tripping. The unit shall be suitable
1 to work on 380-415 V, 3 Phase, 50Hz AC power supply. The unit
shall be filled with first charge of the refrigerant and ready for use
as required. MS/GI powder coated stand with vibration isolation
The ODU shall have low noise condenser fans with external
static pressure of the outdoor unit shall be more then 75 Pa to
avoid hot air recirculation, auto address setting, auto check
function for connection error and complete with indoor and
outdoor units with individual controller and with fittings etc. The
compressor and VRV/VRF Outdoor make should be same
having compressor motor of 6 pole. The unit shall also have
20 HP to automatically modulate the evaporative temperature Nos. 10.00 529068.00 5290680.00
ii) ODU Connecting Kit Nos. 6.00 15000.00 90000.00
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supply of following minimu capacity 4-way/ round flow VRV
Cassette Type Indoor ceiling mounted unit equipped with corded
remote , synthetic washable media pre-filter, fan section with low
noise fan/dynamically balanced blower, multispeed motor, coil
section with DX copper coil, electronic expansion valve, outer
cabinet, drain pan, drain pump, cassette grill, insulation,
necessary supports, vibration isolation etc, suitable for operation
on 230 V ± 10%, 50 Hz single phase AC supply, complete as
2 required. The unit shall have automatic force shut down
provision in case of fire. All indoor Units should have force shut
option to connect with fire alarm adaptor, so that the unit
automatically stops in case or fire. The cooling capacity of indoor
unit will be at air inlet conditions of 27 degree C DBT and 19
degree C WBT. All 4 louvers of the unit shall be independently
adjustable for positiion as per user preference
MR Nominal Capacity 1 TR Nos. 76.00 60430.00 4592680.00
MR Nominal Capacity 1.5 TR Nos. 22.00 65766.00 1446852.00
MR Nominal Capacity 2 TR Nos. 14.00 67146.00 940044.00
MR Nominal Capacity 2.5 TR Nos. 9.00 73586.00 662274.00
MR Nominal Capacity 3 TR Nos. 3.00 74874.00 224622.00
MR Nominal Capacity 4 TR Nos. 2.00 76254.00 152508.00
Supplay, Installation, Testing & Commissioning of the Copper
3 refrigerant pipes with 19mm with nitrile rubber tube insulation of
following sizes.
Gas line and Liquid Line with 19mm thick insulation
MR 41.3mm (Hard Drawn with 1.62 mm Thick Tube) Mtr 96.00 2800.00 268800.00
MR 38.9mm (Hard Drawn with 1.62 mm Thick Tube) Mtr 28.00 2200.00 61600.00
MR 34.9mm (Hard Drawn with 1.62 mm Thick Tube) Mtr 118.00 2100.00 247800.00
MR 31.8 mm (Hard Drawn with 1.62 mm Thick Tube) Mtr 68.00 1500.00 102000.00
MR 28.58mm (Hard Drawn with 1.2 mm Thick Tube) Mtr 110.00 1650.00 181500.00
MR 25.4mm (Hard Drawn with 1.2 mm Thick Tube) Mtr 72.00 1400.00 100800.00
MR 22.2mm (Hard Drawn with 1.2 mm Thick Tube) Mtr 82.00 1450.00 118900.00
MR 19.05mm (Hard Drawn with 1.2 mm Thick Tube) Mtr 120.00 1260.00 151200.00
MR 15.9mm (Soft Drawn with 1.2 mm Thick Tube) Mtr 390.00 1100.00 429000.00
MR 12.7mm (Soft Drawn with 1.2 mm Thick Tube) Mtr 86.00 1040.00 89440.00
MR 9.52mm (Soft Drawn with 1.2 mm Thick Tube) Mtr 480.00 980.00 470400.00
MR 6.4 mm (Soft Drawn with 1.2 mm Thick Tube) Mtr 10.00 720.00 7200.00
Supply & Installation Testing and Commission of Control wiring
4 of 2 core x 1.0 sqmm copper cable through suitable conduits in Mtr 820.00 195.00 159900.00
between indoor and outdoor units.
Supply, Installation, Testing and Commissioning of hard PVC
5 drain pipe with 9mm thick nytrile tube insulation.(With necessary
Lbow, Sockets & Reducers.)
MR 25mm inner dia Rmt 120.00 180.00 21600.00
MR 32mm inner dia Rmt 380.00 210.00 79800.00
MR 40mm inner dia Rmt 180.00 280.00 50400.00
Supply and Commissioning of VRF systems including additional
6 referigernt R410A in all respect to complete the system as per Kgs 180.00 1200.00 216000.00
site requirements
SUB TOTAL 16156000.00
FIREFIGHTING WORK
A PUMPS AND APPURTENANCES
Supplying, installation, testing and commissioning of Electric
Motor Driven Pressurization Terrace Pump having discharge of
1 450 LPM at 35 Mtr head complete with Pump Set, Electric Motor Nos 1.00 73544.00 73544.00
suitable for operation on 415 V ,3 ph, 50 c/s AC supply , Base
Supply, installation, testing and commissioning of Floor/Wall
mounted sectionalised, front operated top entry dust and vermin
proof M.V.Panel Boards suitable for operation at 415V, 3 phase,
2 4 wire, 50Hz distribution system fabricated out of 2.0 mm thick Set 1.00 45000.00 45000.00
CRCA sheet, insulated busbar with heat shrienkable PVC
sleeve, base frame, complete with all accessories including
interconnections, earth bus etc as required.
B PIPE & VALVES ETC.
Supply,Installation,Testing & Commissioning of 'C' Class heavy
duty MS pipe (as per IS 1239 upto 100 mm NB and IS 3589 for
above 100 mm 6.33mm thick) with flanges and fitting such as
bends, tees, reducers, rubber insertions and galvanized nuts and
bolts of following size on surface along wall / shaft with MS
1 bracket, suspended from ceiling/ beam with suspenders duly
painted with two coats of primer and finished with enamel paint
of approved colour laid through pipe or in trench after wrapping
with hassen cloth after applying coal tar primer as required as
per direction of Engineer-in- charge.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing, fixing, testing and commissioning of following size
manually operated hand lever type cast iron double flanged slim
seal wafer type Butterfly valves with EPDM iron disc as per IS-
13095 having pressure ratting PN -1.60 including fixing the same
3 with supply of required jointing materials like rubber insertion, MS
nuts & bolts, paint etc. and testing the joints with required water
pressure etc. all complete as per specification & direction of
Providing, fitting & fixing of following size cast iron double
flanged type dual plate Non return Valve as per IS- 5312 (Part 1):
2004 with ISI mark of pressure ratting PN-1.60 including fixing
4 the same with supply of required jointing materials like flanges,
rubber insertion, MS nuts & bolts, paint etc. and testing the joints
with required water pressure etc. all complete as per
specification & direction of Engineer-in-charge.
Supply,Installation,Testing & Commissioning of Pressure gauge
of 0-16 Kgf/sq.cm. range with cut-off bronze ball valves of
suitable size with all accessories as per direction of Engineer-in-
Supply,Installation,Testing & Commissioning of Pressure Switch
with cut-off bronze ball valves with integral strainer & flare nut
(mixed ends) of suitable size with all accessories as per direction
of Engineer-in-charge.
C DOWN COMER SYSTEM
Supply,Installation,Testing & Commissioning of Stainless steel
Hydrant Valve / Landing valve, of 63 mm NB size, type-A, single
headed , oblique type, as per IS :5290/93 and as per direction of
Engineer-in-charge.
Supply,Installation,Testing & Commissioning of SS short branch
2 pipe with 63 mm male inlet and 19 mm outlet nozzle, as per Nos 2.00 4032.00 8064.00
IS:903 and as per direction of Engineer-in-charge.
Supply,Installation,Testing & Commissioning of 63 mm NB and
15meter long RRL Fire Hose fitted with 63mm intstantaneous
3 stainless steel male & female SS coupling, complete by GI wire Nos 4.00 7077.00 28308.00
binding for Internal Hydrant as per direction of Engineer-in-
Providing supply & fixing of MS Hose Box for of suitable
size(750X600X250mm) to accomodate 2 nos. of 15/ 1 no of 30
mtr long fire hose and a branch pipe, wall mounted type as per
direction of Engineer-in-charge.
Supply,Installation,Testing & Commissioning of Swinging pattern
wall fixing first aid hose reel made from MS sheet and waterways
and moving parts with rubber hose of 20 mm dia. and 30 mtrs.
long with ABS(Plastic) shut-off nozzle as per IS: 444/IS: 12585
Type-I., complete with all accessories as per direction of
Engineer-in-charge.
Providing, fitting and fixing of C.I. 25 MM single air relief valve
with stop cock confirming to IS:14845/2000 with ISI mark for
water works purpose including fixing the same with hydrant riser
including testing & commissioning the system etc. all complete
as per approved specification & direction of Engineer-in-charge.
Providing, fitting & fixing of 2-Way GM fire brigade connection
consisting of 63 mm dia instantaneous type male couplings with
built-in check valves, 150mm dia flanged outlet complete with
bolts, nuts and rubber insertions confirming to IS:904 with ISI
mark including testing & commissioning the system etc. all
complete as per apporoved specification & direction of EIC.
D EXTINGUISHER SYSTEM
Supply,Installation,Testing and Commisioning of ISI marked
1 (IS:2878) Fire Extinguisher ,Carbon di-oxide type capacity 4.5kg Nos 4.00 12133.00 48532.00
with all accessories (Ever safe/Fire shield)
Supply,Installation,Testing and Commisioning of ISI marked
2 (IS:2878) Fire Extinguisher ,ABC type capacity 6kg with all Nos 10.00 5563.00 55630.00
accessories (Ever safe/Fire shield)
Fire buckets (FILLED WITH SAND) round bottom type enamel
3 painted, white inside & Red out side and Letter "FIRE" in black Nos 2.00 4238.00 8476.00
out side and handle with mounting bracket.
E AUTOMATIC FIRE ALARMING SYSTEM
Supply,Installation,Testing and Commisioning of Microprocessor
based 2 zone main fire alarm control panel with LCD
display,Integral System Power Supply unit including Battery
Charger with mounting chasis & lockable type Hinged Door
Complete with sealed Lead Acid maintenance free Battery
Backup.(Agni/system sensor)
Supply,Installation,Testing and Commisioning of Manual call
point with inbuilt isolator module ,test key complete with
base,mounting box,and all other required accessories and as
required.(Agni/system sensor)
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Supply,Installation,Testing and Commisioning of Hooter
3 complete with base,mounting box,and all other required Nos 5.00 7034.00 35170.00
accessories and as required.(Agni/system sensor)
Supply & Fixing of 2 core 1.5 sq.mm, multi strand, copper
conductor, FRLS (Fire Retardent Low Smoke)-PVC insulated GI
Screened Armoured cable with saddle and required
accessories.& Power Cable.
Providing and fixing the signages "In case of fire pull down - with
Manual call point symbol ". Size 6" x 6"
Providing and fixing the signages "In case of fire pull down - with
Fire Extinguisher". Size 6" x 6"
Providing and fixing the signages "Main fire alarm panel." Size 4"
Providing and fixing the signages "Assembly point - with symbol
( A2 Size)" - Size 12" x 12"
5 Providing and fixing the signages "Entry/Exit".Size-4"x12". Nos 10.00 650.00 6500.00
SUB TOTAL 624696.00
Sanitary Installation
Providing and fixing water closet squatting pan (Indian type
W.C. pan ) with 100 mm sand cast Iron P or S trap, 3/6
litre low level white P.V.C. flushing cistern, including flush
1 17.10 pipe, with manually controlled device (Push Button,
low/high) conforming to IS : 7231, with all fittings and fixtures
complete, including cutting and making good the walls and floors
wherever required:
White Vitreous china Orissa pattern W.C. pan of size 580x440
mm with integral type foot rests
Providing and fixing white vitreous china pedestal type water
closet (European type W.C. pan) with seat and lid, 10 litre
low level white P.V.C. flushing cistern, including flush pipe,
with manually controlled device (handle lever), conforming to IS :
7231, with all fittings and fixtures complete, including cutting and
making good the walls and floors wherever required.
17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 75.00 5891.27 441845.01
3 17.34 Providing and fixing toilet paper holder :
Providing and fixing C.P. brass long nose bib cock of approved
4 18.50 quality conforming to IS standards and weighing not less than
Providing and fixing wash basin with C.I. brackets, 15 mm C.P.
5 17.7 pillar taps, 32 mm C.P. brass waste of standard pattern,
including painting of fittings and brackets, cutting and making
good the walls wherever require:
White Vitreous China Wash basin size 630x450 mm with a pair
of 15 mm C.P. brass pillar taps
Providing and fixing CP Brass 32mm size Bottle Trap of
6 17.22A approved quality & make and as per the direction of Engineer-in- Each 116.00 942.35 109312.56
Providing and fixing white vitreous china flat back or wall
corner type lipped front urinal basin of 430x260x350 mm and
340x410x265 mm sizes respectively with automatic flushing
7 17.4 cistern with standard flush pipe and C.P. brass spreaders with
brass unions and G.I clamps complete, including painting of
fittings and brackets, cutting
and making good the walls and floors wherever required :
Range of two urinal basins with 5 litre white P.V.C.
automatic flushing cistern
Range of three urinal basins with 10litre white P.V.C. automatic
flushing cistern
Providing and fixing PTMT soap Dish Holder having length of
8 18.65 138mm, breadth 102mm, height of 75mm with concealed fitting Each 142.00 11968.93 1699588.08
arrangements, weighing not less than 106 gms.
Providing and fixing S.S towel ring minimum distances of
9 MR 37 mm from wall face with concealed fittings arrangement of Each 75.00 266.11 19958.25
approved quality and colour,.
10 18.16 Providing and fixing brass stop cock of approved quality Each 200.00 323.08 64616.74
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen
sink as per IS:13983 with C.I. brackets and stainless steel plug
40 mm, including painting of fittings and
brackets, cutting and making good the walls wherever required
17.10.1 Kitchen sink with drain board
17.10.2 Kitchen sink without drain board
Providing and fixing BRASS Waste Coupling for wash basin
and sink, of approved
quality and colour. Waste coupling 38 mm dia of 83 mm
length and 77mm breadth, weighing not less than 60 gms
Providing and fixing P.V.C. waste pipe for sink or wash basin
including P.V.C. waste fittings complete. Flexible pipe
Providing and fixing uplasticised PVC connection pipe with brass
Providing and fixing uplasticised PVC connection pipe with brass
16 18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
Providing and fixing S.S grating with 125 mm nominal dia with 25
mm waste hole of approved quality and colour.
Providing and fixing 600 x 450 mm beveled edge mirror of
superior glass (of approved quality) fixed with stainless steel
studs, complete with cutting, making holes, studs, all fittings,
screws, washers and making good the walls.
Providing and fixing wash basin with C.I. brackets, 15 mm dia CP
Brass single hole basin mixer of approved quality and make,
including painting of fittings and brackets, cutting and making
good the walls wherever required:-
(a) White Vitreous China Wash basin size 550x400 mm with a 15
mm CP Brass single hole basin mixer
Providing and fixing of approved make and model for
Chrome plated Grab Bar,for Physically challenged toilet, The
20 MR1 work shall include the cutting of walls or floors & making
good,complete as per direction of Engineer in Charge (Make :
MR2 Grab Bar Model : Viking : 1162 or Equivalent Each 50.00 2228.00 111400.00
Providing & fixing C.P. Brass health faucet for ablution with 1
21 MR3 meter long PVC tube, hand shower, couplings, wall hook and Each 75.00 1831.00 137325.00
other accessories.
Providing and fixing 600 mm long C.P.brass Single towel rail
with C.P. brass brackets of approved design fixed with
expandable fasteners of specified size (minimum 25 mm long)
with necessary pla
Internal Drainage Installations
Providing and fixing on wall face unplasticised Rigid PVC rain
water pipes conforming to IS : 13592 Type A, including jointing
24 12.41 with seal ring conforming to IS : 5382, leaving 10 mm gap for
thermal expansion,
(i) Single socketed pipes.
Providing and fixing on wall face unplasticised - PVC
moulded fittings/accessories for unplasticised Rigid PVC rain
water pipes conforming to IS : 13592 Type A, including
jointing with seal ring conforming to IS : 5382, leaving 10
thermal expansion.
12.42.1.2 Coupler -110 mm diameter Each 195.00 127.54 24870.85
26 12.42.6 Shoe (Plain)
Providing and fixing UPVC, P or S trap of self cleaning design
with / without vent arm setting in cement concrete 1:2:4 mix
complete including cost of cutting & making good the wall and
floors wherever required.
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
110 mm inlet & 110 mm outlet Each 115.00 408.00 46920.00
Providing & fixing UPVC Floor trap of self cleansing design
28 MR5 without grating complete
in all respects.
Providing & fixing of Floor Cleanout, round or square with rubber
29 MR seal and flat round cover with screws and other required fitting Each 60.00 1001.00 60060.00
complete as required.
Providing, fixing, jointing and testing in position of ISI marked UV
stabilized uPVC pipes for soil, waste, and vent, Type-B as
per IS : 13592 suitable for rubber ring joints, including all
neccessary specials and fittings (confirming to IS:14735) i.e.
bends, tees, junctions (with or without doors), reducers,
WC connectors, couplers, expansion joints / bellows, cowels,
clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor
level supported by clamp & hangers etc. in concealed /
inside duct / under floor & basement ceiling / external work
etc. including chase cutting as required, excavation and back
filling in all kind of soils, suspended from floor under false ceiling
or embedding the pipes laid under floors / building in 75 mm.
alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) including cost of
shuttering for proper completion of the work, breaking and
making good the walls and floors etc. after pipes have been duly
laid and tested. The rubber ring shall confirm to IS:5382. The
Pipes will be supported with threaded G I rods & U clamps with
nuts, washers etc on 50x50x5 mm slotted angle. The cost will
include all support arrangements. The work includes
commissioning of all pipes lines as per drawings and
specifications and as directed by engg-in-charge at site.
MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) Metre 337.50 536.00 180900.00
MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) Metre 168.75 416.00 70200.00
Providing, fixing, jointing and testing in position ISI marked
(IS:4985) UPVC pipes of min 6 Kg/ Sqcm rating with fitting for
waste pipe from fixtures to floor trap including reduces, enlarger,
31 MR socket, couplers, bends, tees etc including fixing at wall/
ceiling level supported by clamp & hangers etc. cutting
holes in wall/ floors/ slabs and making good the same with
cement concrete 1:2:4 complete as required.
Water Supply Installations
Providing and fixing in position 25 mm diameter mosquito
proof coupling of approved municipal design.
Providing and fixing CPVC pipes having the material stability for
hot and cold water supply including all CPVC plain and brass
threaded fittings including fixing the pipe with clamps at 1.00 mt
33 18.7 spacing. this includes jointing of pipes and fittings with one step
CPVC solvent cement and testing of joints complete as per
direction of engineer
Internal work -Exposed on Wall
18.7.2 20 mm nominal outer dia pipes Metre 244.60 345.68 84552.00
18.7.3 25 mm nominal outer dia pipes Metre 300.00 434.41 130323.36
18.7.4 32 mm nominal outer dia pipes Metre 190.00 532.66 101205.43
18.7.5 40 mm nominal outer dia pipes Metre 255.00 717.04 182844.27
18.7.6 50 mm nominal outer dia pipes Metre 320.00 985.68 315417.31
Providing and fixing CPVC pipes having the material stability for
hot and cold water supply including all CPVC plain and brass
threaded fittings including fixing the pipe with clamps at 1.00 mt
34 18.8 spacing. this includes jointing of pipes and fittings with one step
CPVC solvent cement and the cost of cutting chases and making
good the wall same including testing of joints complete as per the
direction of engineer incharge
concealed work including cutting chases and making good the
18.8.2 20 mm nominal outer dia pipes Metre 269.60 546.27 147272.85
Providing and fixing G.I. pipes complete with GI fittings and
35 18.10 clamps including cutting and making good the walls etc. (internal
18.10.3 25 mm dia, nominal bore Metre 185.00 522.29 96624.20
18.10.4 32 mm dia, nominal bore Metre 301.50 599.28 180681.68
18.10.5 40 mm dia, nominal bore Metre 265.00 771.05 204328.78
18.10.6 50 mm dia, nominal bore Metre 175.00 949.74 166204.42
Providing and fixing G.I. pipes complete with G.I. fittings
36 18.12 including
trenching and refilling etc.
18.12.7 65 mm dia, nominal bore Metre 30.00 817.25 24517.57
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
18.12.8 80mm nominal bore Metre 30.00 977.28 29318.37
Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade
13.61.1 Two more coast on new work sqm 80.00 139.77 11181.66
Providing and fixing gun metal non- return valve of approved
quality (PN 1.6)
18.19.6.2 80 nominal bore
Providing and fixing PTMT Ball cock of approved quality, colour
and make complete with Epoxy coated aluminium rod with L.P./
18.62.3 25 mm nominal bore, 152mm long, weighing not less Each 12.00 488.48 5861.76
Providing and fixing C.P.V.C. ball valve in C.P.V.C. pipe
including jointing of pipes & fittings with one step CPVC solvent
cement and testing of joints complete as per direction of
Engineer in Charge. (Astral/Prince/Prakash make or equivalent)
MR 25mm dia, nominal bore Each 54.00 348.90 18840.60
MR 32 mm dia, nominal bore Each 11.00 525.05 5775.55
MR 40 mm dia, nominal bore Each 40.00 917.05 36682.00
MR 50 mm dia, nominal bore Each 1.00 1693.35 1693.35
EXTERNAL SEWERAGE SYSTEM
Constructing brick masonry manhole in cement mortar 1 : 4 (1
cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1
cement : 2 coarse sand : 4 grade stone aggregate 20mm
nominal size); foundation concrete 1:4:8 mix (1 cement : 4
coarse sand : 8 graded stone aggregate 40 mm nominal
40 19.7 size) inside plastering 12 mm thick with cement mortar 1:3
(1cement 3 coarse sand ) finished with a floating coat of neat
cement and making channels in cement concrete 1:2:4
(1cement : 2 coarse sand: 4 graded stone aggregate 20 mm
nominal size) finishd with a floating coat of neat cement
complete as per standard design
Inside size 90 x 80 cm & 45 cm deep including CI cover with
frame (light duty) 455 x 610mm internal dimensions, total weight
of cover & frame to be not less than 38 kg (weight of cover 23
kg and weight of frame 15 kg)
With common burnt clay F.P.S.(non modular) bricks of classic
designation 7.5
Inside size 120x90 cm and 90 cm deep including C.I. cover with
frame (medium duty) 500 mm internal diameter, total weight of
cover and frame to be not less than 116 kg (weightof cover 58 kg
and weight of frame 58 kg)
With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5
43 19.8 Extra for depth for manholes:
19.8.1 size 90 X 80 cm
With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5
With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5
Providing and fixing square mouth S. W. Gully trap class SP-1
complete with C.I. grating brick masonry chamber with water
45 19.4 tight CI cover with frame of 300 x 300 mm size (inside) the
weight of cover to be not less than 4.50 kg and frame to be not
less than 2.70 kg as per standard design
19.4.3 180 x 150 mm. size P type
With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5
Excavating trenches of required width for pipes, cables, etc
including excavation for sockets, and dressing of sides,
ramming of bottoms, depth upto 1.5 m including getting out
46 2.10 the excavated soil, and then returning the soil as required,
in layers not exceeding 20 cm in depth, including consolidating
each deposited layer by ramming, watering, etc. and disposing of
surplus excavated soil as directed, within a lead of 50 m :
2.10.1 All Kind of Soil
Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Extra for excavating trenches for pipes, cables etc. in all
kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m.
corresponding basic item for depth upto 1.5 metre).
Constructing brick masonry circular manhole 1.22 m internal dia
at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement
:4 coarse sand) inside cement plaster 12 mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating
coat of neat cement foundation concrete 1:3:6 (1 cement : 3
coarse sand : 6 graded stone aggregate 40 mm nominal
size) and making necessary channel in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat cement, all
complete as per standard design :
1.68 m deep with SFRC Cover and frame (heavy duty HD-20
grade designation) 560 mm internal diameter conforming to
I.S. 12592, total weight of cover and frame to be not less than
182 kg. fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal
size) including centering, shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster at the
external surface shall be paid for separately) :
19.11.1.2 With Sewer bricks conforming IS : 4885 metre 0.00 23885.86
Extra depth for circular type manhole 1.22m internal dia (at
49 19.12 bottom) beyond 1.68 m to
19.12.2 With Sewer bricks conforming IS : 4885 Metre 0.00 9235.93
Providing laying and jointing glazed stoneware pipes grade „A‟
50 19.1 with stiff mixture of cement mortar in the proportion of 1:1 (1
cement : 1 fine sand) including testing of joints etc. complete.
Providing and laying cement concrete 1:5:10 (1 cement : 5
coarse sand : 10 graded stone aggregate 40 mm nominal
size) up to haunches of S.W. pipes including bed concrete
as per standard design :
19.3.1 100 mm diameter S.W. pipe Metre 1455.00 452.54 658446.40
19.3.2 150 mm diameter S.W. pipe Metre 0.00 733.41
Constructing brick masonry circular type manhole 0.91 m internal
dia at bottom and 0.56m dia at top in cement mortar 1:4 (1
cement : 4 coarse sand), inside cement plaster 12 mm thick
with cement mortar 1:3 (1 cement : 3 coarse sand) finished with
a floating coat of neat cement, foundation concrete 1:3:6 mix (1
cement : 3 coarse sand
: 6 graded stone aggregate 40 mm nominal size), and
making necessary channel in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) finished with a floating coat of neat cement,
all complete as per
standard design :
0.91 m deep with S.F.R.C. cover and frame (heavy duty,
HD-20 grade designation) 560 mm internal diameter
conforming to I.S. 12592, total weight of cover and frame to be
not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement :
2 coarse sand : 4 graded stone aggregate 20 mm nominal
size) including centering, shuttering all complete. (Excavation,
foot rests and 12mm thick cement plaster at the external
surface shall be paid for separately) :
With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5
Extra depth for circular type manhole 0.91m internal dia (at
53 19.10 bottom) beyond 0.91 m to
With common burnt clay F.P.S. (non modular) bricks of class
designation 7.5
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Providing orange colour safety foot rest of minimum 6 mm thick
plastic encapsulated as per IS : 10910, on 12 mm dia steel bar
conforming to IS : 1786, having minimum cross section as 23
mmx25 mm and over all minimum length 263 mm and width as
165 mm with minimum 112 mm space between protruded legs
having 2 mm tread on top surface by ribbing or chequering
besides necessary and adequate anchoring projections on
tail length on 138 mm as per standard drawing and
suitable to with stand the bend test and chemical resistance
test as per specifications and having manufacture's
permanent identification mark to be visible even after fixing,
including fixing in manholes with 30x20x15 cm cement
concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) complete as per design.
Making connection of drain or sewer line with existing manhole
including breaking into and making good the walls, floors with
cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded
54 19.21.1 stone aggregate 20mm nominal size) cement plastered on both Each 21.00 726.98 15266.54
sides with cement mortar 1:3 (1cement : 3 coarse sand) finished
with a floating coat of neat cement and making necessary
channels for the drain etc. complete for pipes 100 to 230mm dia.
Providing, fixing, testing and commissioning of uPVC SWR
soil, waste pipe confirming to IS : 13592 and IS : 14735
of Type-B pipe, Excavating trenches of required width for
pipes including sockets and dressing of sides, ramming of
bottoms, for all depth including getting out the soil as required
and refilling, consolidating in layers and stacking neatly the
surplus excavated soil including transport and all lead. The
work includes commissioning of all pipes lines as per
drawings and specifications and as directed by engg-in-charge
Providing, fixing, testing and commissioning of uPVC SWR
soil, waste pipe confirming to IS : 13592 and IS : 14735
of Type-B pipe, Excavating trenches of required width for
pipes including sockets and dressing of sides, ramming of
bottoms, for all depth including getting out the soil as required
56 MR and refilling, consolidating in layers and stacking neatly the
surplus excavated soil including transport and all lead. The
work includes commissioning of all pipes lines as per
drawings and specifications and as directed by engg-in-
charge at site.( for gully trap to manhole
SUB TOTAL 9326906.72
HORTICULTURE & SITE BEAUTIFICATION WORK
Uprooting rank vegetation and weeds by digging the area to a
depth of 60 cm, removing all weeds and other growth with roots
by forking repeatedly, breaking clods, rough dressing, flooding
with water, uprooting fresh growths after 10 to 15 days and then
fine dressing for planting new grass, including
disposal of all rubbish with all leads and lifts.
Preparation of beds for hedging and shrubbery by excavating 60
cm deep and trenching the excavated base to a further depth of
30 cm, refilling the excavated earth after breaking clods and
mixing with sludge or manure in the ratio of 8:1 (8 parts of
stacked volume of earth after reduction by 20% : one part of
stacked volume of sludge or manure after reduction by 8%),
flooding with water, filling with earth if necessary, watering and
finally fine dressing, leveling etc. including stacking and disposal
of materials declared unserviceable and surplus earth by
spreading and leveling as directed, within a lead of 50 m, lift up
to 1.5 m complete (cost of sludge, manure or extra earth to be
paid for separately)
Plantation of Trees, Shrubs, and Hedge at site i/c watering and
3 2.57 removal of unserveiceable material’s as per direction of officer in
charge (excluding cast of plant & water)
Trees Plant Each 82.00 7.76 636.49
Shrubs Plant Each 265.00 3.88 1028.48
Hedge Plant / Ground Cover Each 170.00 2.61 442.86
Digitally signed by Rakesh
S. No. DSR 2021 Description Unit Quantity Rate Amount (In Rs)
Digging holes in ordinary soil and refilling the same with the
excavated earth mixed with manure or sludge in the ratio of 2:1
by volume (2 parts of stacked volume of earth after reduction by
18 2.14 20% : 1 part of stacked volume of manure after reduction by 8%)
flooding with water, dressing including removal of rubbish and
surplus earth, if any, with all leads and lifts (cost of manure,
sludge or extra good earth if needed to be paid for separately)
Holes 90 cm dia, and 90 cm deep Each 82.00 152.16 12476.97
Holes 60 cm dia, and 60 cm deep Each 265.00 46.52 12327.63
Holes 45 cm dia, and 45 cm deep Each 170.00 19.88 3380.23
Providing and laying Neelgiri/Mexican grass turf with earth 50mm
to 60mm thickness of existing ground prepared with proper level
and ramming with tools wooden (Dhurmos) and than rolling the
surface with light roller make the surface smoothen and light
waterning with sprinkler and maintenance for 30 days or more till
the grass establish properly, as per direction of officer-in-charge.
Providing and displaying of Raphis Palm having ht. 75 cm to 90
cm with 15 to 18 equal suckers, well developed, full of fresh and
healthy leaves from bottom to top in 35 cm PVC Pots/C.Pots &
as per direction of the officer-in-charge
Providing and stacking of Ficus panda of height 90-105 cm. with
22 8.28 branches and healthy foliage, well formed in cement pots of size Each 250.00 239.24 59810.63
per direction of the officer-in-charge.
Providing and Displaying Ficus Long Island topiary well
developed with fresh & healthy 5 to 6 ball specific size and
shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of
the officer-in-charge.
Providing and Displaying Bougainvillea named variety, Sobhra,
Thima, Marry palmar, Cherry Blossom etc. well developed with
fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm
Cement Pot as per direction of the officer-in-charge.
Providing and stacking of Ipomea (Golden leaves),with fresh and
25 6.15 healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per Each 25.00 21.27 531.65
direction of the officer-in-charge.
Providing and stacking of Wedelia trilobata,full of leaves in 15
cm size of Poly bags & as per direction of the officer-in-charge.
Providing and stacking of Tradescantia, full of leaves in Earthen
28 6.29 Pot/Plastic Pot of size 15 cm. as per direction of the officer-in- Each 50.00 22.33 1116.47
Providing and stacking of Plumeria rubra of height 120-150 cm.
32 7.72 with 3-4 branches and thick stem in big size HDPE bags as per Each 15.00 425.32 6379.80
direction of the officer-in-charge.
Providing and stacking of Bottle palm of ht. 270-300 cm bottom
33 7.12 girth 40-50 cm well developed in big HDPE bags as per direction Each 32.00 584.82 18714.08
of the officer-in-charge.
Providing and stacking of Foxtail palm of ht. 240-270 cm bottom
34 7.44 40 cm well developed in big size HDPE bags as per direction of Each 10.00 691.15 6911.45
officer-in-charge.
Providing and stacking of Polyalthia pendula (Ashok Pendula) of
150-165 cm. in earthen pots of size 25 cm as per direction of the
officer-in-charge.
SUB TOTAL 735577.38
Supplying WORKModular table in completely knock down
conditions with an overall size 2000mm X 2300mm X 750mm
that is to be assembled at site. The construction of the main table
shall be free standing structure constructed with the help of
minifix dowels and pins. The table top shall have the size
2000mm X 900mm made up of 70mm thick Medium density fibre-
board with black & red veneer polished. The top profile shall be
in rectangle shape with both side round edges. The table top
shall be supported on MDF base gable end. The end wall of the
table on the side shall be topped by gable end. The gable end
shall have the size 900mm X 662mm. The gable end shall be
1 made up of 70mm thick Medium density fibre-board and the Each 1.00 44420.34 44420.34
profile shall be in linear shape with black veneer polished. The
table shall be clad with 18mm thick modesty panel which provide
structural support for the table. The modesty panel shall have the
size 1860mm X 500mm with 18mm thick Medium density fibre-
board with black veneer polished connected with both end.
There shall be leg provided of MDF base red veneer having size
150mm X 70mm X 18mm. The table shall have one side unit for
storage purpose with an overall size 1400mm X 450mm X
650mm. The side unit shall be made up of Medium density fibre-
board with black & red veneer polished with top and side 25mm
Digitally signed by Rakesh
S. No. DSR 2021 Providing and supplying a highDescription
back chair with ergonomic Unit Quantity Rate Amount (In Rs)
design, comfortable & aesthetically appealing. The seat and
back shall be made of double layered moulded natural wood and
combination of (18+6)mm thick hot pressed commercial plywood
padded with high resilience polyurethane foam (50+25)mm thick
having density 40kg/m³ in seat and (40+25)mm thick having
density 32kg/m³ in back. The seat and back shall be upholstered
with pure leather tapestry 1mm thick and 573 GSM. The backrest
shall be made by keeping the natural curvature of the spine
which helps to provide full back support as well as head support.
The chair shall be supplied with aluminium arm having polished
2 wooden top completely joint with seat and back. For seating Each 1.00 11389.84 11389.84
durability the chair shall have torsion bar 360 degree revolving
mechanism with upright position locking and tilt tension
adjustment which provides back strength for the chair. The
pneumatic seat height adjustment for healthy seating, user can
adjust seat height up to 65mm with BIFMA standard class-3 gas-
lift to suit them using the lever under the seat. The gas-lift
mechanism should be tested as per ANSI/BIFMA X5.1-2011
standards. The Pedestal should have five legged made of die
cast aluminium having pitch circle dia. 700 mm fitted with 5 nos.
twin wheel castors. The castors of the chair should be injection
Providing and supplying a high back chair with ergonomic
design, comfortable & aesthetically appealing. The seat shall be
made of 15mm thick hot pressed commercial plywood padded
with high resilience polyurethane foam (50+25)mm thick having
density 40kg/m³ and the back shall be made of (15+6)mm thick
double layered moulded plywood padded with high resilience
polyurethane foam 40mm thick having density 32kg/m³. The seat
and back shall be upholstered with leatherite tapestry 0.8mm
thick and 535 GSM. The backrest shall be made by keeping the
natural curvature of the spine which helps to provide full back
support as well as head support. The chair shall be supplied with
3 Chrome plated with cushion arm having leatherite top completely Each 18.00 10915.26 196474.68
joint with seat. For seating durability the chair shall have synchro
knee tilt 360 degree revolving mechanism with four position
locking and tilt tension adjustment which provides back strength
for the chair. The pneumatic seat height adjustment for healthy
seating, user can adjust seat height up to 65mm with BIFMA
standard class-3 gas-lift to suit them using the lever under the
seat. The gas-lift mechanism should be tested as per
ANSI/BIFMA X5.1-2011 standards. The Pedestal should have
five legged made of die cast aluminium having pitch circle dia.
Supplying with 5 Modular
& Placing nos. twintable
wheelin castors. Theknock
completely castors of the
conditions with an overall size 1800mm X 1730mm X 750mm
that is to be assembled at site. The construction of the main table
shall be free standing structure constructed with the help of
minifix dowels and pins. The table top shall have the combination
of 18mm PLPB and 25mm MDF board. The top shall have the
size 1800mm X 830mm made up of 18mm thick Pre-laminated
particle board of grade II of IS 12823 with one side laminate and
finish as per approved shade. The base top shall have the size
1800mm X 830mm made up of 25mm thick Medium density fibre-
board with deco painted. The top profile shall be in rectangle
4 shape with front half round shape and particle board edges shall Each 63.00 11484.65 723532.95
be sealed with 2mm thick thin strip of impermeable PVC that is
cut to fit the size of board panel and duly pasted with the
assistance of edgebander machine at 200 0C and MDF board
with half round post form. The table top shall be supported on
75mm MS powder coated U-clamp. The end wall of the table on
the side shall be topped by gable end. The gable end shall have
the size 730mm X 634mm. The gable end shall be made up of
36mm thick Pre-laminated particle board and profile shall be in
linear shape with appropriate PVC edge banding. The table shall
be clad with 18mm thick modesty panel which provide structural
Digitally signed by Rakesh
S. No. DSR 2021 Descriptiondesigned, comfortable &
Supplying and placing ergonomically Unit Quantity Rate Amount (In Rs)
aesthetically appealing High back chair. The seat shall be made
of 15mm thick hot pressed commercial plywood upholstered with
high resilience polyurethane foam (25+19)mm thick having
density (40, 40)kg/m³ with foam net tapestry 0.9mm thick and
300 GSM and the back shall be made of polypropylene net cover
with breathable mesh tapestry. The backrest shall be made by
keeping contoured lumbar support which helps to provide full
back support and maintain the natural curvature of the spine.
Cushion headrest shall be provided for comfort of head. The
chair shall be supplied with PP arm completely joint with seat.
5 The chair shall have synchro tilt 360 degree revolving Each 63.00 10440.68 657762.84
mechanism with upright position locking and tilt tension
adjustment. The pneumatic seat height adjustment for healthy
seating, user can adjust seat height upto 100mm with BIFMA
standard class-3 gaslift to suit them using the lever under the
seat. The gas-lift mechanism should be tested as per
ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made
up of injection moulded black nylon having pitch circle Dia 700
mm fitted with 5 nos. twin wheel castors which shall be made of
injection moulded black nylon 30% glass filled having self-
lubricating property for friction free movement. The seat size
Supplying & Placing Visitor Chair ergonomically designed for
user comfort & shall have aesthetically appealing design. The
seat shall be made of 15mm thick hot pressed plywood
upholstered with high resilience polyurethane foam (25+19)mm
thick having density (40, 32)kg/m³ with black foam net tapestry
0.9mm thick and 300 GSM and the back shall be made of MS
powder coated frame and hot pressed Malaysian plywood 15mm
thick on edges upholstered with high resilience polyurethane
6 foam 12mm thick having density 23kg/m³ with breathable green Each 150.00 5457.63 818644.50
mesh tapestry. The seat and back shall be fixed with plywood &
metal frame and the armrest shall be used PU arm completely
joint with back. The frame structure shall be cantilever support
type made up of MS CRCA powder coated with 50μ~60μ (DFT)
round pipe of Dia 25.4mm with 2mm thick. There shall be PPCP
shoe provided at the base to avoid scratches on the floor. The
Seat size shall be 475±10 mm(D)X465±10 mm(W) and back size
shall be 440±10 mm(W)X465±10 mm(Ht) from seat. Overall
height shall be = 900±10 mm, overall depth = 475±10 mm &
Supplying = 560±10
Conference table in completely knock down
conditions with an overall size 7500mm X 1500mm X 750mm
that is to be assembled at site. The construction of the main table
shall be free standing structure constructed with the help of
minifix dowels and pins. The table top shall have the combination
of 18mm thick PLPB as top and 25mm thick MDF board as base
top. The top shall be made of 18mm thick pre-laminated particle
board of grade II of IS 12823 with one side laminate and finish as
per approved shade. The base top shall be made of 25mm thick
Medium density fibre-board with deco matt finish. The table top
profile shall be boat like shape with round corners. The top PLPB
7 board edges shall be sealed with 2mm thick thin strip of
impermeable PVC that is cut to fit the size of board panel and
duly pasted with the assistance of edgebander machine at 200
degree Celsius. The base top MDF board shall be half round
post form with groove. Single sided Flip-up box should be
enclosed at table top that houses video, audio, data and power
connection discretely. The table shall be supported by particle
board base gable end. The end wall of the table on the side shall
be topped by gable end. The gable end shall be made up of
36mm thick Pre-laminated particle board and profile shall be in
linear shape with appropriate PVC edge banding 1mm thick. The
Conference table 15 -20 person Each 4.00 18337.63 73350.52
Conference table 50-60 person Each 1.00 68766.10 68766.10
Digitally signed by Rakesh
S. No. DSR 2021 Descriptiondesigned, comfortable &
Supplying and placing ergonomically Unit Quantity Rate Amount (In Rs)
aesthetically appealing Medium back chair. The seat shall be
made of 15mm thick hot pressed plywood upholstered with high
resilience polyurethane foam 50mm thick having density 40kg/m³
with black leatherite tapestry 0.8mm thick and 535 GSM and the
back shall be supported by MS CRCA metal frame upholstered
with black leatherite tapestry 0.8mm thick and 535 GSM with
contoured lumbar support which helps to provide full back
support and maintain the natural curvature of the spine. The
armrest shall be used MS chrome plated PU arm completely joint
with seat and back. The chair shall have swivel tilt 360 degree
8 revolving mechanism with upright position locking and tilt tension Each 11.00 11654.69 128201.59
adjustment. The pneumatic seat height adjustment for healthy
seating, user can adjust seat height upto 100mm with BIFMA
standard class-3 gaslift to suit them using the lever under the
seat. The gas-lift mechanism should be tested as per
ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made
up of MS CRCA chrome plated having pitch circle Dia 700 mm
fitted with 5 nos. 50mm twin wheel castors which shall be made
of injection moulded black nylon 30% glass filled having self-
lubricating property for friction free movement. The Seat size
shall be 480±10
Supplying mm (W)X460±10
and placing mm(D)
ergonomically and back
designed, size shall&be
aesthetically appealing Medium back chair. The seat shall be
made of 15mm thick hot pressed plywood upholstered with high
resiliance moulded polyurethane foam 40mm thick having
density 40kg/m³ with leatherite tapestry 0.8mm thick and 535
GSM and the back shall be made of metal pipe frame
upholstered with breathable mesh and leatherite tapestry 0.8mm
thick and 535GSM. The chair shall be supplied with MS chrome
plated arm with PU top completely joint with seat & back. The
chair shall have synchro tilt 360 degree revolving mechanism
with upright position locking and tilt tension adjustment. The
9 pneumatic seat height adjustment for healthy seating, user can Each 143.00 11654.69 1666620.67
adjust seat height up to 100mm with BIFMA standard class-3 gas-
lift to suit them using the lever under the seat. The gas-lift
mechanism should be tested as per ANSI/BIFMA X5.1-2011
standards. The Pedestal should have five legged MS CRCA
chrome plated having pitch circle dia. 650 mm fitted with 5 nos.
twin wheel castors which shall
be made of injection moulded black nylon 30% glass filled,
confirming to ANSI/BIFMA standard. The Seat size shall be
470±10 mm(W)X475±10 mm(D) and back size shall be 550±10
mm(H) from seat & overall height = 960±10 mm.
Supplying & placing modular table in completely knock down
conditions with an overall size 1800mm X 750mm X 750mm that
is to be assembled at site. The construction of the main table
shall be free standing structure. The table top shall have the size
1800mm X 750mm made up of 25mm thick pre-laminated
particle board of grade II of IS 12823 with one side laminate and
finish as per approved shade. The table top profile shall be in
rectangle shape and the edges shall be sealed with 2mm thick
thin strip of impermeable PVC that is cut to fit the size of board
panel and duly pasted with the assistance of edge banding
machine at 200 degree celsius. The table top shall be supported
10 on metal base powder coated rectangle pipe with cross-section Each 143.00 12220.62 1747548.66
area 40mm X 20mm. The table shall be clad with modesty panel
which provide structural support for the table. The modesty panel
shall have an overall size 1330mm X 380mm with 1mm thick
CRCA silver grey powder coated star perforated sheet
connected with both end. The table understructure shall have
metal base C-type leg having size 730mm X 695mm with cross-
sectional area 60mm X 30mm. There shall be PPCP shoe
provided to avoid scratches on the floor. The manufacturer shall
have basic quality and safety certifications like ISO-9001:2015,
ISO-14001: 2015, ISO-18001:2007, BIFMA Membership &
Digitally signed by Rakesh
S. No. DSR 2021 Supplying & Placing Reception Description
table in completely knock down Unit Quantity Rate Amount (In Rs)
conditions with an overall size 2400mm X 820mm X 1000mm
that is to be assembled at site. The construction of the main table
shall be free standing structure constructed with the help of
minifix dowels and pins. The top shall have the size 2300mm X
695mm made up of 49mm thick Pre-laminated particle board of
grade II of IS 12823 with both side laminate and finish as per
approved shade. The upper top shall have the size 1400mm X
300mm with 49mm thick. The top profile shall be in rectangle
shape with 2mm thick thin strip of impermeable PVC that is cut to
fit the size of board panel and duly pasted with the assistance of
10 edgebander machine at 200 0C. Aluminium profile shall be Each 1.00 15281.36 15281.36
inserted in the side edges. The table top shall be supported on
particle board base strip and upper top shall be on Particle board
base strip having size 200mm X 125mm. The table shall have a
front panel having size 1390mm X 750mm with 49mm thick Pre-
laminated particle board. A wire manager cap shall be provided
on the top of the table for power connection. The end wall of the
table on the side shall be topped by gable end. The gable end
shall have the size 750mm X 850mm. It shall be made up of
49mm thick Pre-laminated particle board and profile shall be in
Supplying with onestorage
& placing clippedunit
withand covered
an overall by 1500mm
size Aluminium
450mm X 750mm. Storage shall be made up of Pre-laminated
particle board of grade II of IS 12823 with both side laminate and
finish as per approved shade. All profile i.e. side, back, top,
shutter, facia, shelf, skirting shall be 18mm thick and base 9mm
thick. The top and side shall be full round post form at front and
other edges shall be sealed with thin strip of impermeable PVC
that is cut to fit the size of board panel and duly pasted with the
assistance of edge banding machine at 200 degree celsius. The
storage shall have 8 nos. of drawer having size 360mm X
163mm, 1 nos. of adjustable shelf having size 710mm X 385mm
12 and 2 nos. of shutters shall be provided for opening and closing Each 8.00 9852.64 78821.12
the storage with the size 360mm X 668mm. The drawer and
shutter shall be operated with 350mm roller base bottom channel
having load capacity 20kg and concealed crank hinge
respectively with SS D-handle. The drawer shall have central
locking mechanism in which all the drawer shall be synchronized
lock with one single key and shutter shall have MP lock. To
protect the wall from kicks, abrasion and serve as a decorative
moulding, skirting shall be provided at bottom with size 1460mm
X 50mm. There shall be buffers provided at the bottom to avoid
Supplying the floor.
& Placing The manufacturer
Modular shall have
table in completely basic
conditions with an overall size 1800mm X 2000mm X 750mm
that is to be assembled at site. The construction of the main table
shall be free standing structure constructed with the help of
minifix dowels and pins. The table top shall have the size
1800mm X 800mm made up of 50mm thick Pre-laminated
particle board of grade II of IS 12823 with one side laminate and
finish as per approved shade. The table top profile shall be in
rectangle shape and sealed with 2mm thick thin strip of
impermeable PVC that is cut to fit the size of board panel and
duly pasted with the assistance of edge banding machine at 200
13 degree celsius. Two wire manager cap shall be provided on top Each 18.00 42469.69 764454.42
for power connection. The table top shall be supported on
particle board base gable end. The end wall of the table on the
side shall be topped by gable end. The gable end shall have the
size 795mm X 690mm. The gable end shall be made up of
25mm thick Pre-laminated particle board and profile shall be in
linear shape with appropriate PVC edge banding. The table shall
be clad with 18mm thick modesty panel which provide structural
support for the table. The modesty panel shall have the size
1750mm X 400mm with 18mm thick pre-laminated particle board
in linear shape with appropriate PVC edge banding connected
Supplying and placing a three seater sofa that shall be
constructed from natural hard wood and commercial plywood
having inner frame. The thickness of the wood should allow for
the heavy tension webbing. The sofa shall have spring attached
and also be padded separately. The frame shall be padded with
high resilience polyurethane foam 100mm thick having density
40Kg/m³ in seat and 68mm thick having density 32Kg/m³ in back.
There shall be cushion arm provided padded with high resilience
polyurethane foam 49mm thick having density 32Kg/m³. The
14 complete structure shall be upholstered with black leatherite Each 4.00 14357.24 57428.96
tapestry 0.8±0.1 mm thick and 535 GSM. The understructure
shall have SS leg with shiny chrome finish having Dia. 38mm.
There shall be shoe provided at the bottom to avoid scratches on
the floor. The seat size shall be 540±10 mm(D) X 1540±10
mm(W), seat height = 430±10 mm, overall width = 1920±10 mm,
overall depth = 760±10 mm & overall height = 750±10 mm. The
manufacturer shall have basic quality and safety certifications
like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA
Membership & AIOTA certification
Digitally signed by Rakesh
S. No. DSR 2021 Description
Supplying & Placing workstation table in completely knock down Unit Quantity Rate Amount (In Rs)
conditions with an overall size 1560mm X 1560mm X 1200mm
that is to be assembled at site. The main top shall have the size
1500mm/600mm X 1500mm/600mm made up of 25mm thick Pre-
laminated particle board of grade II of IS 12823 with one side
laminate and finish as per approved shade. The top profile shall
be in curvilinear shape and the edges shall be sealed with 2mm
thick thin strip of impermeable PVC that is cut to fit the size of
board panel and duly pasted with the assistance of edge banding
degree celsius. The top shall be supported on particle board
15 base gable end. The end wall of the top shall be topped by gable Each 150.00 14357.24 2153586.00
end. The gable end shall be made up of 25mm thick Pre-
laminated particle board with an overall size 590mm X 715mm.
The profile of the gable end shall be in linear shape with
appropriate PVC edge banding. The workstation shall have
panel based partition of 60 mm thick with overall height 1200mm.
The partition shall be linear in profile and provided in the front
side of user as well as on the sides of the user. The top trim, top
bar, mid bar, vertical bar, raceway, skirting shall be made up of
aluminium extrusions (pre-treated) and duly powder coated with
40μ-60μ thick. The trims shall have the size 60mm X 19mm with
Supplying & Placing three seater bench. The seat and back shall
be made up of high quality cold rolled MS perforated sheet of
1.2mm thick, pressed and welded to form the shape. The seat
and back electrostatically coated with epoxy powder and then
cured under heat to allow it to form a skin. The armrest shall be
16 made up of mild steel powder coated tube with 1.2mm thick. The Each 5.00 8067.80 40339.00
base structure shall be supported by MS powder coated with
50μ~60μ (DFT). There shall be PPCP shoe provided at the base
to avoid scratches on the floor. The Seat size shall be 440±10
mm(D) X 405±10 mm(H) from ground. Overall height shall be =
775±10 mm, overall depth = 710±10 mm & overall width =
Providing, placing and installing a slotted angle rack with an
overall size 900mm (W) X 300mm (D) X 1800mm (H). The panel
shall have 5 nos. of shelves made up of 0.8mm thick high yield
strength CRCA sheet of grade ‘D’ confirming to IS: 513. CRCA
17 slotted angle shall be supplied with 2mm thick having size 40mm Each 20.00 4256.38 85127.60
X 40mm. All steel components shall be 50-60μ thick (DFT)
powder coated after 7 tank pre-treatment process flow. Corner
plate (gussets) and fasteners shall be provided for complete
assembly. The manufacturer shall have basic quality and safety
certifications like ISO-9001:2015, ISO-14001: 2015, ISO-
18001:2007, BIFMA Membership & AIOTA certification
SUB TOTAL 9331751.15
GRAND TOTAL 235031944.03
GRAND TOTAL 235031944.03
Digitally signed by Rakesh
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
NIT.pdf
Tender Document
GCC with upto date amendments.pdf
Tender Document
SCC.pdf
Tender Document
MAKE LIST.pdf
Tender Document
Signed IP.PDF
Tender Document
Physical Milestone.pdf
Tender Document
BOQ.pdf
Tender Document
Drawings.pdf
Tender Document
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .