SITC of Bhabani Bhawan main building Lift

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to relevant IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd.

Make : Lift manufacturers approved under Category-I (as per Memorandum of PWD/Govt. of W.B vide memo no. 75-W(C)/1M-20/15 dt. 03/03/2015)

Type: Passanger Lift .

Load : 10 Passenger / 680 Kg

Control: Microprocessor based with serial communication controller in shaft and user interface in landing ,AC variable voltage & variable frequency ( VVVF) (Closed loop)

Machine:- Energy efficient machine, Gearless, without Machine Room

Position of Machine Room: MRL

Speed: 1 Mtrs./ Sec

Floor served: G + 4

Landing: 5, all on same side

Total Rise : 17.6 Mtr

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator. COP & LOP must have stainless steel face plate silver brushed with surface mounted button. Button : All buttons on car & landing shall be luminous, on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendent mode of operation. Display type :Colour LCD / Segmented LCD/LED. Operation Push Button for lift maintenance & service should be on top of the car.

Leveling accuracy:± 5 mm(Micro levelling arrangement )

Car inside :1350mm ( W ) x 1300mm ( D ) x 2200mm (H) or as per OEM standard.

Car Entrance:Clear Opening:- 800 mm (W) x 2000 mm (H ) protected with car door or as per OEM standard.

Car Finish & Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

a) Rear Mid Panel ---- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

b) Rare corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

c) Side Mid Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

d) Side corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

e) Front Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4)

Car Ceiling & Lighting: Stainless Steel with hairline finish (#4) with LED lighting and Fan

Car Ventilation: Cross flow Pressure fan with anodised aluminium grill.

Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening automatic door provided with AC V3F controlled door drive system with 2D infrared curtain of light and mechanical force limiting device,with fire rating of minimum 120 minutes.

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system, with fire rating of minimum 120 minutes.

Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor/infrared detector .

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room

Emergency Alarm: Battery operated alarm bell system in lift car and control room

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - As per manufacturer's standard conforming to respective applicable IS

Hand Rail-Stainless steel mirror finish Hand rail on rear car panels .

Auto fan cut off .

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension: 2050 mm (W) X 1865 mm (D)

Pit Depth :1600 mm as per site condition(Bidder Should visit the site )

Available Overhead : 4020 mm as per site condition (Bidder Should visit the site )

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

N.B. Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish.

Dismantling of existing old Lift materials etc. with owns tools & takles incl. mending good damages and clearing/removing from the site as directed by EIC.

(-) Less cost of old dismantled Lift materials

Please Enable Macros to View BoQ information