Construction of Panchayat Office Building at Makkamabapuram Panchayat at R.K.Pet Union Thiruvallur Dist

Amount

Construction of Panchayat Office Building at Makkamabapuram Panchayat

Earth work excavation and depositing on banks with initial lead and lift in gravelly soil stiff clay, hard stiff clay, murram, boulders mixed with gravel as per SS 20-B for foundation.

Supplying and Filling foundation and basement with M.sand in layers not more than 15cm Thick well ramed, watered and compacted Complete complying with stanard specification.

Filling in Basement with carted Earth in layers of not more than 15cm. Thick well rammed, watered and consolidated complying with standard specifications etc., complete.

Plain Cement Concrete 1:4:8 mix using 40 mm ISS HBG metal including cost and conveyace of all materials and all labour charges, etc.

Brick work in CM 1:5mix using country bricks ground molded of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. i) Below

Brick work in C.M 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc., complete as per standard specification.(Above Base)

Supplying and Fabricating and placing in position MS steel or Ribbed Tor Steel for all Reinforced Cement Concrete works as per the design given including cost of steel and binding wire in all floors etc, Complete complying with stanard specification.(MS rod or RTS bar will be supplied departmentally at section stores and cost will be recoverd at issue rate). the binding wire shall supplied by the contactor.

Supplying & Erecting centering for sides & soffits including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casuarinas props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items i) Below

Supplying & Erecting centering for sides & soffits including necessary supports & strutting up to 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casuarinas props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items ii) Above

Reinforced Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcemeat and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary and bearing surfaces of walls , sides and bottom of the slabs, beams etc., shall be finished smooth with cement mortar 1:3, 12mm thick. and with Kraft paper without claiming extra as directed by the departmental officers complete complying with standard specifications i) Below

Reinforced Cement concrete 1:1.5:3 using 20mm ISS HBG metal for all RCC item of works excluding cost of Rein forcemeat and fabricating charges, centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary and bearing surfaces of walls , sides and bottom of the slabs, beams etc., shall be finished smooth with cement mortar 1:3, 12mm thick. and with Kraft paper without claiming extra as directed by the departmental officers complete complying with standard specifications.ii) Above

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone M.Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing Granolithic pattern floor finish with Plain Cement concrete 1 : 2 : 4 mix using 10-12mm ISS HBG metal and the top rubed smooth etc., complete complying with standard specification as directed. Rate for 10 m3

Paving the Floor with Antiskid tiles of size 305x305x6mm laid in CM 1;2,10mm thick and pointing with white cement 0.40kg per sqm mixed with colouring pigment to suit the colour of the tiles including cost and conveyance of all materials to site and all labour charges etc complete

Dadooing walls with Glazed tiles of any colour and any size laid in CM 1:2, 10mm thick. and pointing with white cement 0.4 Kg per sqm mixed with colouring pigment to siut the colour of the tiles including finishing the joints neatly complying with the standard specifications and as directed by the departmental officers. The Glazed tiles should be got approved from the Departmental officers before execution.

Paving the Top of roof with Solar reflective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three M.Sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Providing Interlocking Paver block of 60mm thick

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with CM 1:5, 12mm thick.over the cement concrete for floor finish including curing etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Painting two coats with approved Exterior Emulsion Paint over one priming coat of cement plastered wall surface and ceiling including cleaning preparing the surface and curing etc, complete

Painting new iron works for doors, windows and Ventilators, Iron bars, Weldmesh, wiremesh, screen, steel bars, flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard

Fabrication and supply of Mild Steel Door of any required size with double leaf,outter frame of 35x35x 5mm equal MSL angle and shutter frame made of 25x25x5mm equal MSL angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 2Nos.horizontal and 3 Nos. diagonal for each shutter using M S flat of size 20x5mm fully covered with 18 gauge plain M S full sheet welded with shutter frame neatly and also fixin by welding 6 Nos. of hold fasts,2 Nos. wind appliances,3 Nos. tower bolts,1 No. aldrop2 Nos. handles, fixing shutterwith6 Nos.of hinges with outter frame of the door including painting the whole unit with one coat best quality of red oxide primer. DOORS

Fabrication and supply of Mild Steel Window of any required size with Three leaf.Outter frame of 35x35x 5mm equal MSL angle, Mullion section made of 35x 35x5mm equal T-section, shutter frame made of 25x25x5mm equal MSL angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 1No.horizontal for each shutter using M S flat of size 20x5mm fully covered with 18 gauge plain M S full sheet welded with shutter frame neatly and also fixin by welding.Protective grill with 12 mm squqre M S rods at an intervel of not grater than 10 cm centre to centre to the outter frame.2 Nos of peg stays with hole for keeping the windows open in different positions,2 Nos. of locking handles fixing the shutters with 4 Nos. of hinges hold fasts, 6 Nos.of hinges with outter frame of the window including painting the whole unit with one coat best quality of red oxide primer. WINDOWS

Fabrication and supply of Mild Steel Window of any required size with Three leaf.Outter frame of 35x35x 5mm equal MSL angle, Mullion section made of 35x 35x5mm equal T-section, shutter frame made of 25x25x5mm equal MSL angle for horizontal and vertical members and the shutter frame strengthened by stiffeners of 1No.horizontal for each shutter using M S flat of size 20x5mm fully covered with 18 gauge plain M S full sheet welded with shutter frame neatly and also fixin by welding.Protective grill with 12 mm squqre M S rods at an intervel of not grater than 10 cm centre to centre to the outter frame.2 Nos of peg stays with hole for keeping the windows open in different positions,2 Nos. of locking handles fixing the shutters with 4 Nos. of hinges hold fasts, 6 Nos.of hinges with outter frame of the window including painting the whole unit with one coat best quality of red oxide primer. WINDOW 2

Fixing of Steel rolling shutters including cost and conveyence to work site and labour cherges etc complete

Solid PVC Door using 19 guage 19mm MS sq. tubes for styles and outer frames, 15mm MS sq. tubes for top, lock and bottom rails. The steel tubes shll be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable suitable rabate for housing the shutter.

Providing and fixing PVC Rainwater Downfall pipes of 110 mm dia with necessary shoes, bends and other speicals, clamps, screws, nails, teakwood plugs etc., complete including cost of all materials complete complying with standard specification.

Wiring with 2 x 1.50 sqm ( 22/0.3 ) PVC insulated unsheathed single core Copper Conductor of 1100 v Grade in suitable PVC Rigid Pipe on wall and ceiling with PVC accesseries with TW Switch box with 5 A F . T . Switch with painting of suitable colour for Light Point and Fan Point ( For Electronic Regulator ) SD 23

Supply and Fixing of 11 W CFL in the existing light point SD 80

Suplying and Fixing of 1200mm (48") AC ceiling fan complete with stepped Regulator as per standard specifications. SD 107

Supply and Fixing of Water TIGHT Bulk Head fitting with Guard for incandescent lamp with 60 w Bulb SD 83

Wiring with 2x1.50 sqm PVC insulated unsheated Sc.alu Cable of conductor of 1100V grade insulated for open plug point . SD 39

Supply and fixing of 32 Amps DPIC Switch of 50 w with Metal Clad with fuse and neutral with Main SD 144

Supply and fixing of TNEB meter Board Suitable For 32 A Single Phase sc .With 32 A Fuse Unit etc., SD 125

Supply and fixing run off 2x1.50sqm PVC insulated Sc . Un sheated Sc conductor of 1100 v grade on 7/20 GI Bearer wire for Service Main SD 69

Supply and run off 4x6 sqm PVC unsheated Sc unsheated , Copper Conductor of 1100V grade for Service Main SD 68

Supplying and fixing of PVC water storage tank of best approved quality and make of super thick with lid of capacity of 500 litres with accessories including giving necessary connection etc., complete as directed by the departmental officer.

Supplying & Fixing in position of Indian type Water closet 580x440mm of approved quality

Supplying & Fixing in position of Eroppiyan Water closet f approved quality

Supplying and Fixing inposition of best quality make White glazed wash basin of size 550x 400mm - 1 No.

Supply and fixing of hand Rail including all other charges

GST Amount for providing Service to Government Contract Works for the above Construction & Maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (Both Construction and Maintenance) above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

A Venu (BID ID -1301385)