GEMC-511687795611180
Awarded to REPUBLIC HARDWARE STORES
₹2.1 L
Products
| Product | Brand / Model | HSN | Quantity | Unit Price | Amount |
|---|---|---|---|---|---|
| Duplex webbing slings | indigenous / Duplex webbing slings for various lifting applications. Strong, flexible & lightweight Polyester construction Lighter than chain & less likely to cause damage Easy to inspect for damage Shock absorbing High resistance to abrasion Webbing sling ends in Becket Eyes End Fittings Eye to Eye Flat Eyes Length 3000 mm Safe Working Load (Choke Hitch) 4 Tons Material PET Safety Factor 7:1 Standards EN 1492-1 Operating Temperature -40 to +100T*C | HSN not specified by seller | 4 No | 1,297 | 5,188 |
| Lever Pulley Hoist It shal | INDEF/ RAJA / Lever Hoist) - It must be portable and easy tooperate fitted with load chain & operated by a lever through ratchet mechanism - Lifting capacity - 6 Ton - All hooks shall confirm to IS:3815-1969 and shall be fitted with safty catches. - Chains shall be of suitable grade and comply with requirements of relevent standard. - Terminal chain stop shall be provided at the free end of the chain - Load chain shall be provided for 7 Meter lift capacity normally. - Operating lever shall be of adequate strength, easy to grip. - Provision for quick winding under no-load should be provided. - The manufacturer shall provide a certificate that it has been tested according to this standard | 73151210 | 1 No | 19,466 | 19,466 |
| Single Part Wire rope sling | Usha Martin/ vardhman / Single Part Wire rope sling IS 2762 (2009) Length 10000 mm Rope dia(D) 32 mm Safe Working Load (Choke Hitch) 8.00 Tons Reeving Thimbles at Both Ends ONE-LEG WIRE ROPE SLING (MECHANICALLY SPLICED | 7312 | 4 No | 10,029 | 40,116 |
| Duplex webbing slings | INDEF/ RAJA / Pulley blocks Hook - The hook shall be forged in one piece and shall be special trapazoidal section point hook with shank as given in Table-3 of IS 15560 (reaffirmed in 1991) BeSpecification for point hooks with shank for 160TBe. The shank of the head fittings shall have thread as specified in IS 4218 (part-3)-1999 BeISO metric screw thread; part-3 Basic dimensions for design profile (first revision)Be and shall be hot clinched after fixing the cross head and the round neck Cross head Be The cross head shall be neatly and cleanly dressed. Holes for the shank of the hook and through pin shall be incorrect alignment and at right angle to each other. Beckets Be The beckets shall be forged in one piece After proof testing, all parts of the block shall be thoroughly examined. The shank of the hook and the sheave shall be rotated freely by hand, and block shall be free from deformation, cracks, flaws and any other defects. The becket shall be tested 1/3 of the proof load applied to the block and there shall not be any visible permanent distortion at t | 73151210 | 4 No | 1,120 | 4,480 |
| D shackles suitable for lifting or securing loads | indigenous / Duplex webbing slings for various lifting applications. Strong, flexible & lightweight Polyester construction Lighter than chain & less likely to cause damage Easy to inspect for damage Shock absorbing High resistance to abrasion Webbing sling ends in Becket Eyes End Fittings Eye to Eye Flat Eyes Length 10000 mm Safe Working Load (Choke Hitch) 16 Tons - one leg lifting Material PET Safety Factor 7:1 Standards EN 1492-1 Operating Temperature -40 to +100�C | HSN not specified by seller | 4 No | 413 | 1,652 |
| Single Part Wire rope sling | Usha Martin/ vardhman / Single Part Wire rope sling IS 2762 (2009) Length 15000 mm Rope dia(D) 38 mm Safe Working Load (Choke Hitch) 11.5Tons Reeving Thimbles at Both Ends ONE-LEG WIRE ROPE SLING (MECHANICALLY SPLICED) | 7312 | 4 No | 18,289 | 73,156 |
| Duplex webbing slings | INDEF/ RAJA / Pulley blocks Hook - The hook shall be forged in one piece and shall be special trapazoidal section point hook with shank as given in Table-3 of IS 15560 (reaffirmed in 1991) �YeSpecification for point hooks with shank for 160T�Ye. The shank of the head fittings shall have thread as specified in IS 4218 (part-3)-1999 �YeISO metric screw thread; part-3 Basic dimensions for design profile (first revision)�Ye and shall be hot clinched after fixing the cross head and the round neck Cross head �Ye The cross head shall be neatly and cleanly dressed. Holes for the shank of the hook and through pin shall be incorrect alignment and at right angle to each other. Beckets �Ye The beckets shall be forged in one piece After proof testing, all parts of the block shall be thoroughly examined. The shank of the hook and the sheave shall be rotated freely by hand, and block shall be free from deformation, cracks, flaws and any other defects. The becket shall be tested 1/3 of the proof load applied to the block and there shall not be any visible permanent distortion at t | 73151210 | 4 No | 590 | 2,360 |
| D shackles suitable for lifting or securing loads | indigenous / D-shackles suitable for lifting or securing loads - High tensile galvanised steel shackles with screw pin to BS3032: 1987 - Safe working load : 8 Ton - Standard : BS 3032:1958 | HSN not specified by seller | 8 No | 648 | 5,184 |
| Single Part Wire rope sling | Usha Martin/ vardhman / Single Part Wire rope sling IS 2762 (2009) Length 2000 mm Rope dia(D) 10 mm Safe Working Load (Choke Hitch) 0.80 Tons Reeving Thimbles at Both Ends ONE-LEG WIRE ROPE SLING (MECHANICALLY SPLICED) | 7312 | 2 No | 330.4 | 660.8 |
| Pulley blocks | INDEF/ RAJA / Pulley blocks Hook - The hook shall be forged in one piece and shall be special trapazoidal section point hook with shank as given in Table-3 of IS 15560 (reaffirmed in 1991) leSpecification for point hooks with shank for 160Tle. The shank of the head fittings shall have thread as specified in IS 4218 (part-3)-1999 leISO metric screw thread; part-3 Basic dimensions for design profile (first revision)le and shall be hot clinched after fixing the cross head and the round neck Cross head le The cross head shall be neatly and cleanly dressed. Holes for the shank of the hook and through pin shall be incorrect alignment and at right angle to each other. Beckets le The beckets shall be forged in one piece After proof testing, all parts of the block shall be thoroughly examined. The shank of the hook and the sheave shall be rotated freely by hand, and block shall be free from deformation, cracks, flaws and any other defects. The becket shall be tested 1/3 of th | 73151210 | 3 No | 2,536 | 7,608 |
| D shackles suitable for lifting or securing loads | indigenous / D-shackles suitable for lifting or securing loads - High tensile galvanised steel shackles with screw pin to BS3032: 1987 - Safe working load : 12.5 Ton - Standard : BS 3032:1958 | HSN not specified by seller | 6 No | 1,474 | 8,844 |
| Pulley blocks | INDEF/ RAJA / Pulley blocks Hook - The hook shall be forged in one piece and shall be special trapazoidal section point hook with shank as given in Table-3 of IS 15560 (reaffirmed in 1991) �/eSpecification for point hooks with shank for 160T�/e. The shank of the head fittings shall have thread as specified in IS 4218 (part-3)-1999 �/eISO metric screw thread; part-3 Basic dimensions for design profile (first revision)�/e and shall be hot clinched after fixing the cross head and the round neck Cross head �/e The cross head shall be neatly and cleanly dressed. Holes for the shank of the hook and through pin shall be incorrect alignment and at right angle to each other. Beckets �/e The beckets shall be forged in one piece After proof testing, all parts of the block shall be thoroughly examined. The shank of the hook and the sheave shall be rotated freely by hand, and block shall be free from deformation, cracks, flaws and any other defects. The becket shall be tested 1/3 of the proof load applied to the block and there shall not be any visible permanent distortion at this load The manufacturer/supplier shall supply a Test Certificate for compliance of each pulley block with the provisions of this standard. For Double sheave pulley blocks : Sheave Size : 65-150 mm Nominal size of fibre rope : 10-40 | 73151210 | 2 No | 4,660 | 9,320 |
| Duplex webbing slings | indigenous / Duplex webbing slings for various lifting applications. Strong, flexible & lightweight Polyester construction Lighter than chain & less likely to cause damage Easy to inspect for damage Shock absorbing High resistance to abrasion Webbing sling ends in Becket Eyes End Fittings Eye to Eye Flat Eyes Length 5000 mm Safe Working Load (Choke Hitch) 10 Tons- one leg lifting Material PET Safety Factor 7:1 Standards EN 1492-1 Operating Temperature -40 to +100��C | HSN not specified by seller | 4 No | 5,663 | 22,652 |
| Single Part Wire rope sling | Usha Martin/ vardhman / Single Part Wire rope sling IS 2762 (2009) Length 15000 mm Rope dia(D) 18 mm Safe Working Load (Choke Hitch) 2.5 Tons Reeving Thimbles at Both Ends ONE-LEG WIRE ROPE SLING (MECHANICALLY SPLICED) | 7312 | 2 No | 4,837 | 9,674 |