Construction of Baba Basukinath Ring Road and Approach of Helipad (with Construction of Inspection Benglow) (Total Length-2.975 Km) for the year 2022-23.

Amount

Clearing and grubbing road land (Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.) RCD SOR - 2.03 (i)A

Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres.(Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m) RCD SOR - 3.06

Construction of Embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300-2. RCD SOR - 3.17

Construction of Embankment with Material obtained from Borrow pits. (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. RCD SOR - 3.16

Construction of Subgrade and Earthen Shoulders (Construction of sub-grade and earthen shoulders with approved material obtained from Borrow pits with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2.) RCD SOR - 3.18

Granular Sub-Base with Graded Material (Table:- 400-2) (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.) RCD SOR - 4.01 B (v)

Wet Mix Macadam (Plant Mix Method) (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.) RCD SOR - 4.14 B

Prime Coat over WMM/WBM (Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.) RCD SOR - 5.01 A (I)

Tack Coat on Bituminous surfaces (Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.) RCD SOR - 5.02 (I)

Tack Coat on Granular surfaces treated with primer (Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.) RCD SOR - 5.02 (II)

Dense graded Bituminous Macadam Grading-II With VG-30 Bulk Bitumen (Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @4.5 percent by weight of total mix and filler, transporting the hot mix to work site laying with a hydrostatic paver finisher with sensor control to the required grade level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 505 complete in all respects with VG-30 Bulk Bitumen.) RCD SOR - 5.04 AB

Bituminous concrete Grading- II With VG-30 Bulk Bitumen (Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 507 complete in all respects with VG-30 Bulk Bitumen.) RCD SOR - 5.05 AB

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-C Type XI retro reflective sheeting fixed over 2mm thick aluminium sheeting vide clause 801.3, 3/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.(x)80 cm x 60 cm rectangular RCD SOR - 8.04 B(x)

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-C Type XI retro reflective sheeting fixed over 2mm thick aluminium sheeting vide clause 801.3, 3/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.B(viii)60 cm equalateral triangle RCD SOR - 8.04 B(iv)

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-C Type XI retro reflective sheeting fixed over 2mm thick aluminium sheeting vide clause 801.3, 3/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.(ii) 90 cm octagonal RCD SOR - 8.04 B(xv)

Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-C Type XI retro reflective sheeting fixed over 2mm thick aluminium sheeting vide clause 801.3, 3/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67. (xii)60 cm x 45 cm rectangular RCD SOR - 8.04 B(xii)

Direction and Place Identification Signs with size Less than 0.9 sqm size Board.(Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with not exceeding 0.9 sqm fixed over back support frame of min 40 x 40 x 5 mm Angle mounted on two nos. of mild steel circular pipe 65 NB, 3.2mm thickness and 4.5m meter total height firmly fixed to the ground by means of properly designed foundation with M 25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing) RCD SOR - 8.05

Solar Powered Road Marker (Solar Stud) Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode.The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280.The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinkikng in 1 Hz.There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours.The height, width and length of the marker shall not be less than 10mmx100mmx100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively.The weight of the marker shall not exceed 0.5 Kilograms.Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer.) RCD SOR - 8.35 Suggestive

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) RCD SOR - 8.13

Kilo Meter Stone Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. (ii) Ordinary kilometre stone (precast) RCD SOR - 8.14 (II)

Boundary pillar (Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting) RCD SOR - 8.16

Cast-in-Situ Cement Concrete M20 Kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-15 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409).PCC M20 for Kerb cast in situ. RCD SOR - 8..01(ii)

Providing and laying factory made chamfered edge Cement Concrete,paver blocks in footpath, parks, lawns, drive ways or light traffic,parking etc, of required strength, thickness & size/ shape, made by,table vibratory method using PU mould, laid in required colour &,pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand,bedding layer through vibratory compaction by using plate vibrator,,filling the joints with sand and cutting of paver blocks as per required,size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade,with approved colour, design & pattern. DSR 16.91.1

Dismantling of Structure (Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres.) (iii) (B) Stone Masonry Structures in Cement mortar RCD SOR - 2.04 (iii) B

Excavation for strucutres Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. (i)Ordinary soil (A) Mechanical Means (i) up to 3m RCD SOR - 12.01 (i) B(i)

Plain/Reinfoced Cement concrete in open foundation complete as per drwaing and technical specifications. A)PCC Grade M15 (i)PCC Grade M15 using batching plant & Concrete pump RCD SOR - 12.08 A case-i

Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and technical specifications. (B) Random Rubble masonry (coursed/uncoursed) RCD SOR - 12.07 (B)

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and technical specifications (A)Random Rubble Masonry (Coursed/uncoursed) RCD SOR - 13.04 A

Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. RCD SOR - 16.01

Providing and laying pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications.(A) Stone/Boulder RCD SOR - 16.04 A

Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification RCD SOR - 16.05

Laying Reinforced cement concrete pipe NP4 / prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets . 1200 mm dia RCD SOR 9.04 B

Pointing with cement mortar (1:3) on brick work in substrucutre as per technical specifications RCD SOR - 13.02

Back filling behind abutment, wing wall, return wall complete as per drawing and technical specifications (A) Granular Material . RCD SOR - 13.09 A

Brick masonry work in 1:3 in substructure complete excluding pointing and plastering, as per drawing and Technical Specifications RCD SOR - 13.01

Plastering with cement mortar (1:3) on brick work in substructure as per technical specifications RCD SOR - 13.03

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces) RCD SOR - 8.08

Furnishing and Placing Reinforced/ Prestressed cement concrete in super-structure as per drawing and Technical Specification (B) RCC Grade M-25 Batching Plant, Transit Mixer and Concrete Pump (i) For solid slab super-structure (p) Height upto 5m RCD SOR - 14.01 B(i) p

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications RCD SOR - 14.04

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications (B)PCC Grade M20 (p)Height upto 5m RCD SOR - 13.05 B(p)

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and technical specifications RCD SOR - 14.02

Providing weep holes in Brick masonry/ Plain/Reinforced concrete abutment , wing wall/ returen wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20 H towards drawing face. Complete as per drawing and technical specifications. RCD SOR - 13.08

Providing and laying of filter media with granular materials/stones crushed aggregates satisfying the requirements laid down in clause 2504.2.2 of MoRT&H specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wing wall and return wall to the full height compacted to a firm condition complete as per drwaing and technical specification. RCD SOR - 13.1

Providing Tar Phelt Cushion under the Deck Slab RCD SOR - N/S

Filler joint Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans not exceeding 10 m to cater for a horizontal movement upto 20 mm, covered with sealant complete as per drawing and technical specifications. RCD SOR 14.17 (iii)

Filler joint Providing and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight RCD SOR 14.17 (iv)

Number and Writing The Culvert no etc….. NS

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications (G) RCC Grade M30 (p) Height upto 5m, RCC Grade M30 using batching plant, transit mixer & concrete pump RCD SOR - 13.05 G(p)

Providing and laying Flooring complete as per drawing and Technical specifications laid over cement concrete bedding. Rubble stone laid in cement mortar 1:3 RCD SOR 16.08 A

PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification (i) PCC Grade M15 using batching plant & Concrete pump RCD SOR - 14.10 case-i

Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification RCD SOR - 14.11

Drainage Spouts complete as per drawing and Technical specification RCD SOR - 14.09

Reinforced Cement Concrete Crash Barrier (Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with Reinforced Cement Concrete with HYSD reinforcement conforming to MoRT&H specification and as per details given IRC-5 (Fig.-5, b) including dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board etc., as per approved drawing and at locations directed by the Engineer, all as specified. (Area- 0.243 sqm./meter, single face)) M-30 Grade Concrete RCD SOR - 8.22 A (ii)

PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.) RCD SOR - 12.04

Plain/Reinfoced Cement concrete in open foundation complete as per drwaing and technical specifications. RCC Grade M20 RCC Grade M20 using batching plant, transit mixture & Concrete pump RCD SOR 12.08 C I

Plain/Reinforced cement concrete in sub-strucutre complete as per drawing and Technical specifications RCC Grade M20 Height upto 5m RCC Grade M20 using batching plant, transit mixer & concrete pump RCD SOR 13.05 E p

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. RCD SOR - 12.42

Supplying, fitting and placing HYSD bar reinforcement in sub structure complete as per drawing and technical specifications RCD SOR - 13.06

Overhead Signs (Providing and erecting overhead signs with a corrosion resistant 2mm thick aluminium alloy sheet reflectorised with high intensity retro-reflective sheeting of encapsulated lense type with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans & as per IRC: 67) (A) Truss and Vertical Support RCD SOR - 8.07 A

Fixing Of Reflective Sheeting Including all Cost Of Materials and Fitting Charge Complete Work. RCD SOR - NS

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. SOR - 5.1.1

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) SOR - 5.1.2

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) SOR - 5.1.7

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) SOR - 5.1.8

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) SOR - 5.1.10

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. SOR - 5.2.3

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.2.11

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. SOR - 5.2.23

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) SOR - 5.3.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) SOR - 5.3.1.4

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) SOR - 5.3.9.1

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). SOR - 5.3.11

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) SOR - 5.3.10

Providing and laying damp proof course (DPC) 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). SOR - 5.3.5

Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). SOR - 5.3.20

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete SOR - 5.3.17.1

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform SOR - 5.3.17.3

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers SOR - 5.3.17.5

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts SOR - 5.3.17.6

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases SOR - 5.3.17.7

Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges SOR - 5.3.17.19

Supplying, fitting and fixing good quality, well dressed and well seasoned teak wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I. SOR - 5.4.2

Supplying, fitting and fixing 38mm , thick good quality well dressed and well seasoned teak wood fully paneled shutter in doors and window with 25mm, thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding door, bolts, tower bolts, handled or rings, hooks and eyes, cleats, sand blocks as per schedule, taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.4.9

Supplying, fitting and fixing 38mm , thick good quality well dressed and well seasoned sal wood wire netted shutter in doors and windows with fly proof screen of 18 S.W.G. X12 to 16 mesh per cm2 with oxidised iron fittings such as hinges, sliding doors boltes tower bolts handles or rings, hooks and eyes, cleats, sand blocks as per schedule and 3mm thick plain glass panes fitted with teak wood beads and taxes all complete as per building specification and direction of E/I. SOR - 5.4.30

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. SOR - 5.4.32

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. SOR - 5.4.39

providing ply wood partion up to 2.5 m hight with 4mm thick commerical ply wood of standerd make fitted and fix both sides over sal wood frame of 50x50mm horiz members including cost of anchoring the partitior to floors and wall properly and provinding 2 coats of senthetic enamel paint over a coat of priming of approved shade and make and leaving space for doors if necessary all complete as per drawing specification and direction of E/I. SOR - 5.4.47

Providing reinforcement (Round bars confirming to IS. 432 dia.in mm (I.S. 2062 Gr.A) of 6 & 8mm dia rods as per approved design and drawing excluding carriage of bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. SOR - 5.5.1

Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 {only valid for Tata (Tiscon),SAIL, JSPL, Electrosteel ltd. Bokaro and Vizag (RINL)} SOR - 5.5.4

Providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (a) 10mm (TMT coil Fe 500) {only valid for Tata (Tiscon),SAIL, JSPL, Electrosteel ltd. Bokaro and Vizag (RINL)} SOR - 5.5.5 a

Providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (b) 12mm (TMT coil Fe 500) {only valid for Tata (Tiscon),SAIL, JSPL, Electrosteel ltd. Bokaro and Vizag (RINL)} SOR - 5.5.5 b

Providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (c) 16mm (TMT coil Fe 500) {only valid for Tata (Tiscon),SAIL, JSPL, Electrosteel ltd. Bokaro and Vizag (RINL)} SOR - 5.5.5 c

Providing Tor steel reinforcement of 20mm,25mm, 28mm & 32mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. SOR - 5.5.6

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) SOR - 5.5.12

Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.) SOR - 5.5.13

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. SOR - 5.6.3

Providing 25mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layers 19mm. Thick (1:2:4)with 12mm to 6mm. Size graded stone chips and top layer 6mm. Thicks (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I. SOR - 5.6.7

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.7.1

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.7.3

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.7.6

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. BCD SOR 5.7.11

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. SOR - 5.7.14

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface includingpreparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I. SOR - 5.8.21

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. SOR - 5.8.32

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly, scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. SOR - 5.8.45

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. SOR - 5.10.33

Feeling trees of the girth (measured at a height of 1 m above ground level) , including cutting of trunks and branches , removing the roots and stacking of serviceable material and disposal of unserviceable material. SOR - DSR 2.33.1

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade.8mm thick (mirror polished and machine cut edge)Area of slab over 0.50 Sqm SOR - DSR 7.38.1.1

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. SOR - DSR 8.31

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to1000 mm), with double speed adjustment with necessary accessories and screws etc. completeHydraulic door closer SOR - 9.84 DSR

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopperaluminium hanging floor door stopper, SOR - 9.101.2 DSR

30 mm Thk. Factory made POLYVINYL Choride PVC Door Shutter made of Styles and rains of a UPVC hollow Section of size 60x30mm and wall thickness2mm(+-0.2mm) with inbuilt decorative moulding edging on one side.The styles and rails mitred and joint at the corners by means of ms .galvanised/plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screw.The styless of the shutter reainforced by inserting galvanised M.S tube of size 25x20 mm and 1mm(+-0.1MM) Wall thickness. The lock rail made up of h section a upvc hollow section of size 100x30 mm and 2 mm (+ 0.2 mm) wall thickness fixed to the shutter styles by means of plastic galvanised M.S.u cleats the shutter frame filled with a upvc multi chambred single panel of size not less than 620mm having over all thickness of 20mm and 1 mm (+0.1mm) wall thickness the panels filled vertically and tie bar at two places by inserting horizantally 6 mm galvanised M.S road and fastened with nuts washers complete as per manufacture's specification and direction of Engineer -in-charge.POLYVINYL Choride PVC Door Shutter made SOR - DSR 9.118.2

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5 mm, made out of extruded 5mm extrude rigid pvc foam sheet, mitred at corners and joimed with 2 nos of 150 mm long brackets of 15x15mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm MS.square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame.The door frame The door frame to be fixed to the wall using M.S. screws of 65/100mm size, complete as per manufacture specification and direction of Engineer-in-charge. SOR - DSR 9.119

Providing and fixing prestressed steel door frames conformingto IS 4351 manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges jamb,lock jamb,bead and if required angle threshold of mild steel angle of section 50x25 mm or base ties of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanical means including M.S . pressed butt hinges 2.5 mm thick with morter guards lock strike-plate and shock absorbers as specified and applying a coat of apporved steel primer after pre-treatment of the surface as direction ofEngineer-in-chare.FIXING WITH ADJUSTABLE LUGE WITH SPLIT END TALL TO EACH JAMB SOR - DSR 10.14.1.1

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works SOR - 10.25.2 DSR

Providing and fixing fly proof wire gauze to windows, clerestory windows & doors with MS Flat 15 x 3 mm and nuts & bolts complete. Stainless steel ( grade 304) wire gauze of 0.5mm dia wire and 1.4mm apertute on both sides SOR - DSR 10.29.2

chequerred precast cement concrete tiles 22mm thk in footh path & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles Dark shade pigment using ordinary cement SOR - DSR 11.20.3

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacture) of 1st quality conforming to IS 15622 of approved make in all colours shades except white lvory, Grey Fume red brown laid on 20 mm thick cement mortor 1:4 (1 cement: 4 coarse sand), jointing wth grey cement slurry 3.3kg /sqmm including pointing the joints with white cement and matching pigments etc, complete. SOR - 11.40 DSR

Providing and laying polished granite stone flooring in required design and patterns in linear as well as curvilinera portion of the building all complete as per the architectural drawings with 18 mm thick stone slabs over 20 mm (average) thick base of cement mortar 1:4( 1 cement : 4 coarse sand) laid and jointed with cement. slury and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing tc. all complete as specified and as directed by the Engineer-in-charge.polished granite stone slab jet black, cherry red, elite brown, cat eye or equivalent SOR - DSR 11.56.1

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . SOR - 5.6.28

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socket ed pipes. 110 mm dia P.V.C. rain water pipes SOR - DSR 12.41.2

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion PVC Single Tee with door of 110 x 110 x 110 mm SOR - DSR 12.42.3.2

110x110x110mm SOR - 12.42.4.2

PVC Bend 110 mm SOR - 12.42.5.2

PVC Shoe(plain) 110 mm SOR - 12.42.6.2

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. SOR - SR 12.43.2

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms SOR - 12.46 DSR

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete . SOR - DSR 13.26

Providing and applying white cement based putty of average thickness 1mm , of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. SOR - 13.8

Finishing walls with textured exterior paint of required shade new work ( two more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) SOR - 13.46.1

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement mixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin- Charge : SOR - 22.7.1 DSR

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) SOR - 21.1.1.2 DSR

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge With float glass panes of 4.0 mm thickness SOR - 21.3.1 DSR

Providing double layer Naria- tiles in roof including cost of all labour and materials, taxes, all coplete as per building specification and direction of E/I. SOR - 5.9.7

Brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever handles SOR - DSR 0413

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200mm Nominal size dia. SOR - 23.3.3 D.S.R.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. SOR - 23.12/ D.S.R.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia. SOR - 23.13.3/ D.S.R.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. SOR - 23.14.3/ D.S.R.

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I SOR - 18.12.6/ D.S.R.

Supplying and fitting of 2.0 HP submersible pump set having head of 100m, including all taxes, royalty etc all complete job as per direction of E/I SOR - 139-M1055 /DWSD RATES

Copper conductor, three core , XLPE/PVC insulated & armoured cable. Supplying XLPE/PVC insulated cable 1100 V grade with ISI mark. Three core, soild/stranded copper conductor with 6mm thick 25mm width M.S. spacer with G.I. earth wire 6 sqmm complete in an approved manner 3 core 4 sq mm SOR - Jsr Srl.No.143, Pg 44(xi) CB 6-3

Brick -8km SOR -

sand-5 km SOR -

Chips-75 km SOR -

Metal-69 km SOR -

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I. Horizontal 32 mm dia SOR - 3.1.7

Vertical 32 mm dia SOR -

40 mm dia SOR -

25 mm dia SOR -

Cutting chhajja or corince for laying G.I. / C.P.V.C pipe and restoring the same with R.C.C. (1:2:4) brick work in cement mortor (1:4) as per specification and direction of E/I. SOR - 3.1.17

Making holes in walls for laying G.I. / C.P.V.C pipe and restoring the same after pipe laying as per specification and direction of E/I.125 mm thick wall SOR - 3.1.18

250 mm thick wall SOR -

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. Mirror (600 x 450mm) SOR - 3.1.21

C.P. brass dish container medium quality with screw and hinges etc. SOR - b

Angular Stop Cock (long Thread) SOR - vi

Toilet Paper holder SOR - xxv

Glass self 22" SOR - xxvi

C.P. brass tower rail SOR - xxi

C.P. brass soap dish SOR - xxiii

Providing and fixing CP brass bib cock of approved quality conforming to IS :8931 15mm nominal bore SOR - DSR 18.49.1

Providing and fixing CP brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15mm nominal bore SOR - DSR 18.51.1

S/F/F viterous white glazed earthenware I.W.C 580mm long With 10 Liter Low Level P.V.C. cistern SOR - 3.2.1 c

With 'P' trap - 10 ltr. Low level PVC cistern SOR - 3.2.2 b

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of exacavted earth within initial lead and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I. 50x 0.450 x 0.600 SOR - 3.3.1(ii)

Lbour for alying, fitting and fixing NP2 R.C.C. spun pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leakproof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complet as per specification and direction of E/I. 150mm dia R.C.C. spun pipe SOR - 3.3.6.2

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I. SOR - 3.3.8

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. SOR - DSR 18.48

Supplying NP2 R.C.C. hume pipe with collar as as per I.S.S. 458-1971. 150mm dia SOR - JSR Sl. No.118 Page 30.(ii)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm witha pair of 15 mm C.P. brass pillar taps SOR - DSR 17.7.1

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brazsckets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x460 mm bowl depth 200 mm Kitchen sink without drain board SOR - DSR 17.10.2.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including jointing of pipes and fittings with one step CPVC solvent cement trenching , refilling and testing of joints complete as per direction of Engineer in Charge.Internal w 25 mm nominal outer dia Pipes SOR - DSR 18.9.3

32 mm nominal outer dia Pipes SOR - 18.9.4

40 mm nominal outer dia Pipes SOR - 18.9.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.15 mm nominal outer dia Pipes SOR - 18.8.1

20 mm nominal outer dia Pipes SOR - 18.8.2

25 mm nominal outer dia Pipes SOR - 18.8.3

C.P. Gratings Circular type - 100mm dia SOR - 18.58.1.1

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 SOR - DSR 19.32.1

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion. 110 mm diameter SOR - DSR 12.41.2

110x110x110mm SOR - 12.42.3.2

i) Single tee without door 110 x 110 x 110 mm SOR - 12.42.4.2

110mm shoe SOR - 12.42.6.2

110mm bend SOR - 12.42.5.2

110mm bend SOR - 12.42.5.2

110mm SOR - 12.42.1.2

sw gully trap p type 150x100 SOR - 1902 dsr

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.Make-Schneider(LIVIA) /Legrand (Ardear/Woods)/Havells/ABB/ROMAGr-B SOR - 1.3.3

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required. SOR - 1.31

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required. SOR - 1.32

Supply & fixing 20A SPN MCB Industrial Socket Outlet: Supply and fixing of 20A, 240V, SPN insustrial type socket outlet with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required. SOR - 2.18

Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. SOR - 1.5

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. Make-Polycab/ Havells/RK Kabel/KEI 2x1.5 Sqmm + 1x1.5 sqmm earth wire SOR - 1.7.1

2x2.5 Sqmm + 1x2.5 sqmm earth wire SOR - 1.7.2

4x6 Sqmm + 2x6 sqmm earth wire SOR - 1.7.10

4x10 Sqmm + 2x10 sqmm earth wire SOR - 1.7.11

S/F TP MCB DB: Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR). 4 ways (4+12 ways) double door ( Power=2 nos+ 2 nos=Lighting)Make-Schneider/Legrand/L&T/ABB/Siemens SOR - 2.9.4

S/F TPN RCCB: Supplying & fixing following rating, TP&N 415 V, residual current circuit breaker(RCCB) , having a sensitivity current upto 300mA in existing MCB DB complete with connections, testing and commissioning etc. as required.40 Amps SOR - 2.17.2

63 Amps SOR - 2.17.3

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. 6/32A Single Pole SOR - 2.12.1

40A TPN MCB - for Lighting DBs SOR - 2.12.9

50/63A TPN MCB SOR - 2.12.10

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.5/6 AMPS, one way switch SOR - 1.24.1

5/6 Amps, 3 pin socket outlet SOR - 1.24.4

S/F Ceiling Rose: Supplying and fixing 2 pin 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. SOR - 1.33

Supplying and fixing Modular type blanking plate-Supplying and fixing modular blanking plate on existing modular plate switch box excluding modular plate etc. as required. SOR - 1.26

S/F Batten Holder: Supplying and fixing batten/angle holder including connection etc. as required. SOR - 1.34

S/F Electronic Musical Call bell: Supplying and fixing electronic musical call bell suitable for D.C/A.C, single phase 230 volt, complete as required. SOR - 1.37

ITC fluorescent fitting directly on surface :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper cond. SOR - 1.41

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required. SOR - 1.44

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required. SOR - 1.25

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required. SOR - 1.48

Telephone Wiring in Existing Conduit: Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.2 pair SOR - 1.16.2

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.Telephone socket outlet SOR - 1.24.6

TV antenna socket outlet SOR - 1.24.7

S/F PVC Conduit: Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, RJ45 Cat 6 data outlet for computer network.25 mm( for telephone+TV) SOR - 1.21.2

Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required. Lightning Conductors=2 nos + Panels=1 no). SOR - 3.6

P/F 25 x 5mm copper earth strip in pipe:- Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required. SOR - 3.11

Extra Salt & Charcoal for Copper Earth Plate Elecrode:- Providing and fixing salt and charcoal or cock for copper earth plate elecrode complete etc as required. SOR - 3.8

P/F 25 x 5mm copper earth strip in ground :- Providing and fixing 25mmx5mm cpper earth strip in surface / recess as earth strip electrode including soldering welding etc. as required. SOR - 3.14

Providing and Fixing G.I Lightning Conductor Finial : P/F of lighting conductor finial, made of 25mm dia 300mm long G.I tube, having single prong at top, with 85mm dia 3mm thick G.I base plate including holes etc. complete as required. SOR - 4.2

GI lightning conductor tape in horizontal run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required. SOR - 4.7

GI lightning conductor tape in Vertical run - Providing and fixing of GI tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required. SOR - 4.8

Supply of Decorative Ceiling Fan: Supplying and fitting of 1200 mm Sweep regular/ decorative model AC ceiling fan , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC. SOR - JSR M-778

Supply of Ceiling Fan: Supplying and fitting of 1200 mm Sweep regular AC ceiling fan , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC. SOR - JSR M-772

Supply of Exhaust metal Fan(15"): Supply and fitting of 380mm(15"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/ Havells/Crompton) SOR - JSR M-776

Supply of Exhaust metal Fan: Supply and fitting of 230mm, 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/ Havells/Crompton) SOR - JSR M-774

Double LED tube light fitting made of die cast Aluminium Housing 2x20 W Bettal Tube Light suitable for surface mounted. SOR - JSR M-1555

LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required. ( Make -Bajaj / Havells/ Philips) SOR - JSR M-855

Supply and fixing following size / modules GI box along with modular base and cover plate for mudular switches in recess etc as required (1 or 2 module 78mmx78mmx45mm). SOR - JSR 2018 1.27.1

Cat6 Indoor 23 AWG Cable 2 Run CAT6 UTP Cable: SITC of CAT6 UTP LAN Cable in the existing surface/ recessed steel/ PVC conduit as required for Network only . Make-Legrand/Panduit/Ortronics) ; SOR - DSR 2018; 1.53.2

PVC Conduit Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preffered Make- AKG/NORPACK/Polycab/Dauphin 25 mm SOR - 1.21.2

Providing and ejecting chemical emulsion for pre constructional anti treatment and creating a chemical barrier under and alround the column, pits, wall trenches, basement excavation,top surface of plinth fillling junction of walls and floor along with external permeter of exterior building joint, surrounding of pipe etc. SOR - NS

Polyester vertical blinds :Luxurious metal hardware profiles deliver long lasting, high quality product with Multi-level light control, multi-level privacy control, Lightweight fabric to allow maximum light diffusion. Excellent UV protection, insulation and energy savings. Fabric treated to resist stains and minimize dust built up. Gentle Wash SOR - NS

Supplying , fitting and fixing pasting 2 mm thick sunmica on both sides of single leaf flush door shutter , colour to be decided by engineer in charge at site with taxes all complete and all labour charges all complete as per specification and direction of E/I. SOR - NS

Supplying UPVC casing pipe of 125mm dia to use as 4" dia -do -complete jobAdd 10 % CP SOR - 122/ DWSD RATESPg 42

Labour charge for filling good quality metal fiter (50mm to 100mm size ) with all lift as per specification and direction of E/I. 22/7(3.0x3.0)/4 SOR - NS-X

Labour charge for filling good quality of stone metal fiter (20mm to 63mm size) 22/7(3.0x3.0)/4 SOR - NS

Supplying and laying 150mm Coir mat in nylon net. 22/7(3.0x3.0)/4 SOR - N.S

Providing and laying of 150mm dia P.V.C. pipe for outlet of water from Catch Besin to water Recharging Pit all accessories l.e lubricants, solvent cement, clamp, ring, sockets, Bends etc. (SUPREME SW.R.) SOR - N.S

HYDT: Cost of drilling 200mmx165mmx125 meter deep borewell in all kinds of soil and rock in rural area for installation for pump set with hydraulic DTH rig machin all complete includin supplying all material tools drilling rig. Air compressure and equipments as well as fuel,lubricants and cost of transportation of rig machine and other vehicles upto the site. a. from 0 to 50 m SOR - 119/M1035 DWSD RATES

HYDT: Cost of drilling 200mmx165mmx125 meter deep borewell in all kinds of soil and rock in rural area for installation for pump set with hydraulic DTH rig machin all complete includin supplying all material tools drilling rig. Air compressure and equipments as well as fuel,lubricants and cost of transportation of rig machine and other vehicles upto the site. a. from 0 to 50 m(b) From 51.00 M to 125.00 M SOR - 119/M1035 DWSD RATES

Supplying and fitting of standared make starter pannel board with arrangement of all necessory protection ,including all taxes , royalty etc all complete job as per direction of E/I SOR - NS

Ceiling light(Bathroom): Supply and fixing of white and glass, steel with , Torando lamp basesuitable for LED 12W with protection-IP44 bathroom safe. Make Philips-12NC CODE-915002702002/ Bajaj/Havells SOR - Analysis Rate

Mirror Light(bathroom and dress room): supply ,installation, of wall light,Stain nickel and glass, metal, lamp base suitable for LED 6W with protection-IP21 bathroom safe. Make Philips-12NC CODE-915004471601/ Bajaj/Havells SOR - Analysis Rate

Surface Light(Veranda/balcony/staircase) Square: Surface LED downlighter, warm white aluminium with lamp base LED 15W, lumen 900lm. Make Philips-12NC CODE-919215850239/ Bajaj/Havells SOR - Analysis Rate

LED Bed Side Light: Supply, installation commissioning of wallmounted adjustable neck to direct light of LED bedside light white metal & synthetics with lamp base LED 3W, lumen 150lm. Make Philips-12NC CODE-91925850349/ Bajaj/Havells SOR - Analysis Rate

LED Picture Light: Supply, installation commissioning of wallmounted LED picture light aluminium with silver finish with lamp LED 6W. Make Philips-12NC CODE-919215850143/ Bajaj/Havells SOR - Analysis Rate

Inverter Split AC-1.5 Te : Supply, installation , testing and commissioning of 1.5 Te , 230 V, 50Hz , inverter AC. Make- Hitachi/Mistubishi/ Daikin SOR - Analysis Rate

Supply & fixing of refrigerant pipes in copper class 1 with 12 mm Nytrol Tube insulation- For Split AC SOR - Analysis Rate

SITC of Drain Water pipe with insulation -20mm dia SOR - Analysis Rate

Length - 2053.0 mm.Width - 1875.0 mm Height - 1134.0 mm SOR - CHOCOLATE KING BED

Depth - 450.0 mm.Width - 450.0 mm .Height - 517.0 mm SOR - CHOCOLATE BEDSIDE TABLE

Dressing Table:Depth - 450.0 mm Width - 450.0 mm Height - 1710.0 mm Dressing Stool – Depth - 320.0 mm Width - 350.0 mm Height - SOR - CHOCOLATE PREMIUM DRESSING TABLE

Width - 1100 mm Depth - 605 mm Height - 1005 mm SOR - CHOCOLATE STUDY UNIT

1200 x 600 x 750-MAIN DESK 900 x 450 x 750-ERU 390 x 435 x 529-PEDESTAL SOR - MAYFAIR MAIN DESK+ERU+PEDESTAL

Thick Cushion, Centre-Tilt Mech, Upright Position Locking, Soft Top Fixed Arms, Tilt Tension Adj, Nylon Pedestal SOR - REGENCY HIGH BACK

Upholstered with fabric, High resilience Polyurethane foam, one-piece armrests, Tubular frame. SOR - REGENCY VISITOR WITH ARMS

Ergonomic designed Back & Wide Seat,Round Edged Seat Shell,Easy to Adjust for Floor Levelling, 32 Possible SOR - MATRIX 3 SEATER WITH COMMON ARMS

1981H x 916W x 486D SOR - STORWEL PLAIN

BROADWAY V2 1 SEATER SOR - BROADWAY SOFA 3+1+CORNER

BROADWAY V2 3 SEATER SOR - NS

BROADWAY V2 SMALL CORNER SOR - NS

BROADWAY V2 LH SOR - NS

BROADWAY V2 RH SOR - NS

135cm(W) 80cm(D) 75cm(H) SOR - BRAWN DINING TABLE

CHAIR- 45cm(W)52cm(D)99cm(H) SOR - TIA DINING CHAIR

124cm(W) 57cM(D) 42cm(H) SOR - CAFERIA COFFEE TABLE

MS Powder Coated U/S, Fixed Arm Rest SOR - BEAT VISITOR

2 DOOR WARDROBE-201.3cm(H) 45cm(W) 58.2cm(D) 450W DRAWER- 201.3cm(H) 45cm(W) 60cm(D) 2 DOOR OHU-60cm(H)90cm(W) 60cm(D) SOR - KALISTA 2 DOOR WARDROBE+KALISTA 2 DOOR+KALISTA 450W DRAWER

Online UPSSITC of Single Phase Online 2 KVA UPS with required nos.of external batteries, rack and interconnecting cables for battery for 30 Min backup; Prefered Make-Emerson/Numeric SOR - Market Rate Analysis

16 Port POE SwitchSupply, fitting, fixing, connecting and testing of switch with 16- 10/100/1000T POE port eco-friendly WebSmartswitch delivering up to 30 Watts(upto minimum 6 ports) per port (PoE+) to support video surveillance and security cameras, wireless access points, IP phones and other PoE powered devices having total power budget of 185 watt with 2 SFP combo ports, Switching Capacity 32 Gbps and Forwarding Rate 23.80 Mpps, operating temperature 0ºC to 45ºC, Performance:- 14,880pps for 10Mbps Ethernet,148,800pps for 100Mbps Ethernet1,488,000pps for 1000Mbps Ethernet, MAC addresses: 8K,VLAN IDs available: 4K,Max VLANs: 256,Packet buffer: 1MB,DRAM: 64MB,Flash: 16MB ,Warranty 5 year from Day 1 . L2 Smart Managed Data Switch consists of : Power cord India, right angle,1 year free service pack,Preffered Make-CISCO Model-WS 2960x-24PS-L, Allied Telesis-GS950/16PS HP_ARUBA- 2530-24G. SOR - Market Rate Analysis

Bullet/ Dome Network CameraSITC of 2 MP IR Metal Bullet/ Dome Network Camera,1/3" Progressive Scan CMOS,1920x1080 @30fps,Color: 0.01 Lux @ (F1.2, AGC ON),0.018 Lux @ (F1.6, AGC ON), 0 Lux with IR,H.265+, H.265, H.264+, H.264,Three streams,120dB WDR, 2 behavior analyses, and face detection, BLC/3D DNR/ROI,IP67, IK10,Built-in micro SD/SDHC/SDXC card slot, up to 128 GB,3-Axis adjustment, Up to 50 Mtr IR Range, 3D DNR; ICR; EXIR, up to 50m; DC12V&PoE; Built-in micro SD/SDHC/SDXC slot; cloud service, should have protection level of IP67, IK10 TVS 2000V Lightning Protection, Surge Protection and Voltage Transient Protection, should support ONVIF (PROFILE S, PROFILE G), ISAPI,Preffered Make- Axis/Hikvision/Pelco SOR - Rate Analysis

Surveillance Hard DiskSITC of 4TB WD Surveillance Hard Disk storage; Preffered Make- WD/Seagate SOR - Rate Analysis

43 Inch LED Panel 43" Full HD Panel with Native Resolution1,920 x 1,080 (FHD), Brightness(Typ.,cd/m²)-350, LED Panel,Input-HDMI (2), DVI-D, RGB, Audio, USB, Output-Audio (Off/Fixed/Variable),Speaker-20 W (10 W x 2), Preffered Make-LG/Samsung SOR - Rate Analysis

Patch Panel-24 Port Fully LoadedSITC of 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). Preffered Make-Legrand/Panduit/Ortronics SOR - Rate Analysis

HDMI CableSITC of HDMI Cable-2 Mtr;Make- Krammer/Wyrestorm SOR - Rate Analysis

HDMI CableSITC of HDMI Cable-2 Mtr;Make- Krammer/Wyrestorm SOR - Rate Analysis

Wall Mounted 9U Outdoor RackSITC of 9 U Wall Mounted Rack : SITC of Fully Loaded 9U Wall Mounted Rack 600 x 500; Preffered Make-Legrand/APW/Dlink/Comrack/ Valrack/ President SOR - Rate Analysis

Add 18 % GST (in Basic Rate must fill 18)

Add 1% Labour Cess (in Basic Rate must fill 1)

M/S SATYA CONSTRUCTION

HARI NANDAN CHOUDHARY

M/s CHITRA CONSTRUCTION

SUJATA UDIT BUILDERS PVT LTD

MANOJ KUMAR SINGH