Special repair to toilets and bathrooms at Bldg No P-321 and P-322 under GE (West) Jalandhar Cantt

Amount

Demolition of cement concrete at any position and removing surplus spoil/debris out of Defence Land complete all as specified and directed

M&L for cement concrete type E-2 type 1:5:10 (40mm graded aggregate) as in sunken flooring complete all as specified and directed.

M & L for 15 mm thick rendering on concrete surfaces finished even and smooth without using extra cement in cement mortar 1:3 as in sunken floors using WPC 3% by wt of cement complete all as specified Note : WPC shall be measured and paid separately under respective item.

Supply only Integral water proofing compound conforming to IS-2645 complete all as specified.

M&L for painting the plastered/concrete surface with a coat of hot blown paving industrial bitumen 85/25 at the rate of 1.20 kg/sqm including cleaning the surface complete all as specified and directed.

M&L for cleaning the side/bottom of sunken floor before applying 25mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in padding of sunken floor finishing the surface even and smooth by using extra cement complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc and removing surplus spoil/debris out of Defence Land complete all as specified and directed

M & L for 15 mm thick rendering on concrete surfaces finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified

M & L for 15 mm thick rendering on concrete surfaces finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified

M&L for 5mm thick plastering in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified.

M&L for repairing of RCC projections, chajjas , roofs, facia etc. by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced with welded mesh of weight exc 2kg per sqmtr but n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling surface all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces and applying one coat of white wash on ceiling surface all as specified and directed by Engr-in-Charge.

M&L for preparing new plastered or unplastered wall surfaces and applied two coats of cement base paint over one priming coat all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatments on wall surfaces and applied two coats of cement base paint complete all as specified and directed by Engr -in-charge.

M&L for preparation of new plastered surfaces or unplastered surfaces of walls and applying two coats of white wash all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces or unplastered surfaces of walls and applying two coats of white wash all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and disposal of rubbish outside MD land complete all as specified

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded aggregate as in sub floor , sub base concrete surface finished even & rough to receive topping floor/tiles finish/layer complete all as specified.

M&L for non skid joint free ceramic coloured tiles of size not less than 300mmx300mm, 6-7 mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for coloured glazed tiles of size not less than 300mmx450mm, 6 - 7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10 mm thick rendering in CM 1:4, all as specified and directed

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies , canopies , deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel high yield strength TMT bars 10 mm dia and over cut to length bent to shape require including, cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

All as per item no. 25 above but area exc 1.5 Sqm and not exc 4 Sqm each complete all as specified.

Material and labour for Steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mmx25mm single rebated comprises of glazed skeleton shutter EWR Sec 50mmx20mm and 1mm thick and two openable leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1 using 20mm graded stone aggregate. (Four Nos for each window) including following fittings welded to framed shutter :- (a) Holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) MS tower bolt 150mm long per leaf -02 Nos, (d) ‘Z’ sec 20mm x 25mm, 100mm long stopper per leaf -01 No, (e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (f) MS pintal hinges of size 75mmx12mm per leaf -02 Nos, (g) Fabrication and fixing arrangement as per drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3. Note: Wire gauge/glass shall be measured and paid for separately.

All as per item no. 27 above but as in gauged windows. Note for item No 27 & 28 :- (i) Wire gauge/glass/painting/Grill shall be measured and paid for separately. (ii) Drg No CEJZ/TD-1019 & 1020, Sheet 1/3 to 3/3 are not being uploaded and the same can be seen in this HQ on any working day

M & L for steel ventilator with top hung shutter including hinges, steel peg stay fixed type complete all as specified and directed

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified.

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as specified.

M&L for preparation of new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, supplying and fixing in opening as per specification and drawing.

Supply & Fixing 100mm size butt hinges extruded aluminum alloy with galvanised mild steel hinge plate complete all as specified.

S&F aluminum anodized barrel tower bolt of extruded section of size 150mm complete all as specified.

S&F extruded aluminum alloy handle fabricated of size 150mm complete all as specified.

Taking up of or down steel tubing and connections 15mm bore and connections, including cleaning for refixing or removing to store yard complete all as specified and directed,

Taking up of or down steel tubing and connections 20 mm bore and connections, including cleaning for refixing or removing to store yard complete all as specified and directed,

Refixing old steel tubbing & connection in new or old position (walls ceiling/floors etc) of 15mm bore pipe all as specified.

All as per Srl item No 41above but 20mm bore pipe all as specified.

S&F 15mm bore galvanized iron tubes medium grade with all fitting and fixed complete to walls, ceiling or laid in floor complete all as specified.

All as per description of item No 43 above but for 20mm bore tube complete all as specified.

M&L for cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sun shades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth in brick walls complete all as specified and directed.

S&F stop cock/angle cock, 15 mm cast copper alloy with long shank & cup with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 20mm bore iron fixed complete all as specified.

S&F bib tap fancy type cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete fixed complete all as specified. .

S&F squatting pan WC orrisa pattern size 580 x 440 mm white with integral foor rest with P or S trap incl provn of lime concrete bedding incl breaking up existing damaged WC seat and connecting flush pipe etc and make good to floor complete all as specifed.

S&F PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle incl brackets and flush pipe of polyethylene of low or high density with flush pipe 10 Ltr capacity complete all as specified.

S&F vitreous china urinal half stall urinals (back or corner wall type) complete incl providing and fixing plugs bedding urinal against wall in CM(1:2) securing urinal to plugs with and incl 60cm long bras screws, pointing aroung urinal back in cement incl and fixing and flush pipe, grating with coupling and union for discharge with urinal spreader complete all as specified.

M&L for PVC connection fiber, reinforced 450 mm long with brass check nut and PVC washers at both ends complete all as specified.

S&F 1000 ltr rotational moulded polythylene water storage tank double layer (Cylindrical vertical with closed top) hosted and fixed in position incl dismantling of existing tank of any description complete all as specified.(ISI marked)

S&F 20mm for ball valve brass high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified.

S&F brass chromium plated shower rose of 125mm size, with or without swivel joints including fixing to steel pipe or union complete all as specified.

Supply & fix in repairs brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges complete all as specified and directed.

Supply and fixing square grating of PTMT of size 150mm dia with centre hole fixed in cement mortar 1:3 complete all as specified.

Supply and fixing PTMT shelf fixed with and including chromium plated brass screws and wooden/plastic cleats (min wt 300gm) including taking down old one complete all as specified and as directed.

Dismantling of 100 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Dismantling of 75 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Material & labour for cast iron soil, waste and vent pipe of bore 100mm, sand cast type in any length with or without ears with cement joints fixed to wall/laid in trenches complete all as specified and directed.

Material & labour for cast iron soil, waste and vent pipe of bore 75mm, sand cast type in any length with or without ears with cement joints fixed to wall/laid in trenches complete all as specified and directed.

Material & labour for cast Iron bends (any radius) ducks foot rest or heal rest of size 100mm complete all as specified and directed.

Material & labour for cast Iron bends (any radius) ducks foot rest or heal rest of size 75mm complete all as specified and directed.

Material & labour for CI branch pieces single (equal or unequal) ordinary or inverted fitted with oval access door of size 100mm complete all as specified and directed.

Material & labour for CI branch pieces single (equal or unequal) ordinary or inverted fitted with oval access door of size 75mm complete all as specified and directed.

Material & labour for cast iron bends (any radius), diminishing pieces or tapers of size 100mm with inspection eye complete all as specified and directed.

Material & labour for cast iron bends (any radius), diminishing pieces or tapers of size 75mm with inspection eye complete all as specified and directed.

Material & labour for cast iron floor trap outlet diameter 100mm, plain with grating including jointing with solvent & cement concrete 1:2:4 complete all as specified and directed.

Supply and fix galvanised iron tubes 32mm bore 450mm long beveled cut at both ends as in GI spout in sunken portion for insertion in the sunken floor through walls and finishing the surfaces in cement mortar 1:2 to match with the existing surfaces complete all as specified and directed.

Supply & fix in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in trenches including necessary cutting chasing etc. complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth without using extra cement complete all as specified.

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down carefully existing point wiring aluminum/ copper conductor for light or fan or socket or power etc on wooden batten or in conduit including fittings and accessories like switches, sockets, lights fitting, regulator, wooden board and making good disturbed portion to match with existing complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white/ coloured top sheet cover 3.0 mm thick , for One light point controlled by one way switch complete all as specified and directed.

All as per item No. 75 above but one 3 pin socket outlet 5 amps on independent board with other switches, complete all as specified and directed. .

All as per item No. 75 above but one 3 pin socket outlet 5 amps on same board with other switches, complete all as specified and directed. .

All as per item No. 75 above but with 2.5 sqmm multistranded copper conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board, complete all as specified and directed.

Taking down old unserviceable sub main wiring 6/4.00 Sqmm 1100 volts grade two runs of single core PVC insulated, unsheathed copper conductor, including taking down casing/capping/PVC conduit complete all as specified and directed

Material & labour for submain wiring with two runs of single core 6 Sqmm (nominal area) PVC insulated multistranded copper conductor cable (FRLS) drawn through and including 20 mm dia. PVC rigid concealed conduit and conduit accessories and 6 sqmm PVC insulated copper wire for continuous earth continuity conductor all as specified and directed by Engr-in-charge. Note : Two run of 6 sqmm cable and one run of 6 sqmm along with 20mm dia PVC conduit will be measured as one unit.

Supply and fix switch piano flush button type, 5 Amps, 230V AC, single pole, one way complete all as specified and directed

Supply and fix switch piano flush button type, 5 Amps, 230V AC, single pole, two way complete all as specified and directed

Supply and fix socket out let 5 pin 5 Amp flush type, 230/250 volts complete all as specified.

Supply and fix socket out let combination multi purpose, universal type 6 pin 5/15 Amp 230/250 volts on independent board complete all as specified.

Supply and Fix batton holder, PVC/Polycarbonate type insulated body along with LED lamp 15 watt complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 65 x 50 mm three terminal PVC / Polycarbonate isolated body complete all as specified.

Taking down main switch/DBs of any size and making good disturb surface of wall/floor complete all as specified and directed

Supply and fix DB, double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar complete all as specified and directed.

Supply & fix MCB SPN, 63 amps, DP 240 Volts complete all as specified and directed.

Supply & fix MCB SP, 6 to 32 amps, 240 Volts complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continuous earth wire on pole, testing the earthing after completion complete all as specified and directed. Note :- (I) Earth pit shall be constructed 50cm from the side of excavation to avoid sinking of pit (II) PCC chamber shall be (1:3:6) using 20mm graded stone aggregate and 50mm thick RCC (1:2:4) type B-1 cover slab reinforced with 8mm dia TMT steel bars @ 100mm c/c both ways complete all as specified and directed. .

Supply & fix in replacement LED batten light fitting 20W(double side) including LED lamp with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type with retrofit LED rod 20 watt and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed. Make :Havells cat part No.LHFYBWP1TB1W020 & Tube rod cat pt No. LHLDCLXNUL8x020 or equivalent as mentioned in appendix 'B'

Supply & fix in replacement LED street light fitting 20W including LED lamp pressure die cast aluminium IP66 with surge protection device of 10KV, IK7 LED (SEOUL) 6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed incl bracket and fixing clamps. Make :Havells cat part No.LHETBXU7PA6W048 HSN Code-9405 or equivalent as mentioned in appendix 'B'

Taking down and refixing of serviceable fittings complete all as specified and directed.

M/S Vinod Kumar

HYLAND CONSTRUCTION COMPANY

B.P CONSTRUCTION CO

M/S RAJESH CONSTRUCTION COMPANY

siddharthenterprises

SINGH AND SONS

G S TRADERS