SPECIAL REPAIR TO BLDG NO P 13 MORTUARY STORAGE ACCOMADATION BLDG NO TO 289 JCOs LIVING ACCN BLDG NO T 74 AND SR TO OR TOILETS AND BATHROOM BLDG NO T 840 AND T 653 UNDER AGE B R II OF GE 865 EWS LEH

Amount

Taking down chowkhat or frames with shutters (without taking off shutters from frame) area n.exc 1.50 Sqm each complete all as specified and directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed by Engr-in-Charge.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

All as per Srl item No 3 here-in-above but on ceiling complete all as specified and as directed

M&L for 2nd class soft wood clean sawn as in scantling fixed with nails (timber framed and fixed) including dismantling of timber scantling over 40 Sqcm as in section in any position (framed work).complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section including dismantling of timber in fillets, rails, posts, rafters purlins etc under 40 Sqcm as in section in any position (framed work).complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) as directed

M&L for Cement concrete type D-2, 1:4:8 (using 40mm graded aggreate) 100 mm thick as in sub -floors ,sub- bases, etc complete all as specified and directed by Engr-in-charge.

M&L for 100 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in floors, hardstanding, concrete roads including brooming complete all as directed by Engr-in-charge.

M&L for precast cement concrete block masonary type C-1 , (using crushed stone 20mm graded aggregate) set and jointed in cement mortar 1:6 exc 10cm in width including demolition brick work / block masonry or stone/ boulder masonry, built in built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick/pcc block or conc surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and direced by Engineer-in-Charge.

M&L rendering 15mm thick in CM 1:6 on other than fair faces of concrete or brick surfaces as in wall finishes even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L rendering 15mm thick in CM 1:4 on fair faces of concrete or brick surfaces as in wall finishes even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for prepration of new plaster surface of wall and applying two coat of cement base paint over a coat of primer including complete removal of balance area complete all as specified and direced by Engineer-in-Charge.

M&L for preparation of new plastered surface of wall by complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer including 3 mm thick wall care putty to obtain smooth finish complete all as specified and as directed by Engr-in-Charge.

Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern complete all as specified and directed by Engr-in-Charge.

S&F MS works as of angles or tees,fixed independently cut to shape drilled incl. bending and welding angles of grade 410-FE including dismantling of existing steel work complete all as specified and directed

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S&F Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick as in ridges, valley gutters drip etc of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws as specified

Taking down chowkhat or frames with shutters (without taking off shutters from frame) area exc 1.50 Sqm but n.exc 4 Sqm each complete all as specified and directed by Engr-in-Charge

S&F for 30 mm thick flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides, supply and fixed to chowkats, complete all as directed by Engr-in-charge.

S&F IInd class softwood as in plain solid straight chowkhats wrought framed rebated on the solid put together with glue pinned at joints complete all as specified and direced by Engineer-in-Charge.

S & F steel windows with side hung shuter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars complete all as specified and directed by Engr-in-Charge

S & F steel windows with side hung shuter including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars complete all as specified and directed by Engr-in-Charge

S & F 35 mm thick 2nd class hardwood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and direced by Engineer-in-Charge.

S&F mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and direced by Engineer-in-Charge.

M&L PCC 1:3:6 type C1 (using 20mm graded aggregate) as in anchoring hold fast, bed block and like complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with beading to wooden frames complete all as specified and directed by Engr-in-charge.

M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

M&L for preperation of new or previously untreated wooden surface of any description over 10cm in width or girth and applying two coats of synthetic enamal paint over a coat of Pink primer complete all as specified and as directed by Engr-in-Charge.

M&L for preperation of new surface of steel of any description over 10cm in width or girth and applaying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L Non-Skid ceramic Coloured Tiles 7 to 8mm thick(squre/rectanglar) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors over 15 mm screed bed or bedding layers in cement mortar 1:6 Set and Jointed in neat Cement Slurry and Pointed in Colour Cement to match, complete all as specified and as directed.

M & L glazed (coloured) ceramic tiles of size 450x350x7 mm thick, as on vertical surfaces, over 10 mm thick rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement as in dado, skirting etc to match with the shade of tiles all specified and directed

Dismantling posts or struts (Wood, steel or RCC) any section, including taking out embedded portion, posts embedded in concrete, brick work, masonary etc and making good disturbed portion, complete all as specified and directed by Engr-in-Charge.

Dismantling fencing wire mesh, any type complete all as specified and directed by Engr-in-charge.

S & F, Rolled tubular sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.and similer work conforming to Fe-410 Gde E-250 .complete all as specified and directed.

M&L for one coat of oil bound distamper on old decorated surfaces of walls incl preperation complete all as specified and directed.

M&L for preparation of old untreated steel surface of any description over 10cm in width or girth and change of existing colour including removal of scaled paint and applying one coat of synthetic enamal paint complete all as specified and as directed by Engr-in-Charge.

M&L Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, laying UG cables, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out as specified and directed

Returning, filling in ,including spreading,levelling ,watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed by Engr-in-charge

Removing excavated soil material n, exc 50m and depositing where directed at a level n, exc 1.5 m above the starting point complete all as specified and directed by Engr-in-charge

M&L PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in foundaion, filling and mass concrete. complete all as specified and directed by Engr-in-charge.

M& L, Plain cement concrete , type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates) as in coping, cills, steps, in lintels upto 1.5m clear span and similar other works like bands, plinth courses, lacing courses, bed plates, water troughs and the like incl weathring, slightly rounded or chamfered angles and throating, incl necessary form work, complete all as specified and directed by Engr-in-Charge. (Note - Reinforcement if provided, shall be measured and paid separately under relevent items).

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-charge.

Removing excavated material to a distance exc. 500 mtr but n. exc 1.5 Km above the starting point and depositing where directed at a level n exc. 1.5 m, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engr-in-charge.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including incl screed bed or bedding layer of cement Mortar (1:6), 20 mm thick for laying floor finishes, necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish all as specified and directed by engr in charge.

M&L for hardcore of gauge n.exc 63mm , deposited , spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-charge

M&L Forming Contraction (Dummy) joints 35mm deep x 10mm wide, filled with sealing compound Grade `B', complete all as specified and as directed by Engr-in-Charge.

M&L Forming 20mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `B', as in 100 mm thick slab, complete all as specified and as directed by Engr-in-Charge.

M&L for painting lines, dashes, arrows, letters, etc. on roads, pavements and the like exc 10cm wide with road marking paint, white or golden yellow complete all as specified and as directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement, M & L, concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L Machine pressed precast concrete coloured interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade , complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base complete all as specified and as directed by Engr-in-Charge.

M&L for two coats of Synthetic enamel paint of any description on new plastered surfaces or concrete surface or kerb stone surface of any description over 10cm girth or width not other wise described over a coat of primer.complete all as specified and directed by Engineer-in-Charge.

M&L for Preparing newly plastered surfaces of walls including Chalk whiting, on plastered surfaces and applying two coats of distemper oil emulsion, complete all as specified and as directed.

M & L Non - skid coloured Ceramic tiles 7 to 8 mm tick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. over screed bed 15mm thick in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed

M&L for factory made brown colour solid WPC (wood particle composite) door frame of size 100mm x 63mm single rebate 100% lead free made from single extruded process material with density 0.78 Kg/RM , complete all as specified and as directed.

Providing and fixing 28mm factory made solid WPC (wood particle composite) moulded door shutter single panel design with wood grain texture. The density of the door shutter not less than 600 Kg/Cum should be 100% lead free door complete all as specified and directed

S&F in repair 200mm long aluminium anodised barrel tower bolt of extruded section in old or new position complete all as specified and direced by Engineer-in-Charge.

S&F 200mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direced by Engineer-in-Charge.

S&F in repair 150mm extruded aluminium alloy handles, cast type, anodised complete all as specified and direced by Engineer-in-Charge.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

M&L one coat of white wash on wall surface including preparation of old decorated surfaces of walls complete all as specified and directed by Engineer-in-Charge.

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections and set aside for re-use or removal to store complete all as specified and directed by Engr-in-charge.

Taking up or down 25/32 mm bore steel tubing and connections and set aside for re-use or removal to storecomplete all as specified and directed by Engr-in-charge.

S & F 20mm 3-layer PP-R (polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as per manufacture instructions and as directed by Engineer in Charge.

S & F 25 mm 3-layer PP-R (polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as per manufacture instructions and as directed by Engineer in Charge.

Dismantling of CI or reinforced concrete /PVC of bore jointed in cement mortar and taking out of trenches complete all as specified and directed by Engr-in-charge.

M&L for PVC (SWR) pipe single socketed, 75mm dia soil, waste, in any length with rubber joints, laid in trenches or in floor complete all as specified and directed

S&F 110mm bore PVC (SWR) pipe single socked in any length with rubber ring joint, laid in trenches or in floor complete all as specified and directed by Engr-in-charge.

S/F 75 mm dia (SWR) bend any radius complete all as specified and directed by Engr-in-charge.

S/F 110 mm dia (SWR) bend any radius complete all as specified and directed by Engr-in-charge.

M&L PVC (SWR) multi floor trap 75mm dia plain with grating including jointing with solvant cement complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) 'S’ trap of 125/110 mm bore complete all as specified and directed by Engr-in-Charge.

S & F in repair grating doom 125MM dia with waste hole of PTMT complete all as specified and directed by Engr-in-charge.

S&F in repairs Vitreous China squatting pan 'Orissa' pattern,size 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) with PVC (SWR)110 MM 'S' trap and all as directed by Engineer-in-Charge.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with linlet,ball valve, float and handle including brackets,flushing pipe including of brackets complete all as specified and directed by Engr-in-charge.

S & F in repairs 20mm bib taps with chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-charge.

S&F 20mm bore stop cock, fancy type, chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule complete all as directed by Engr-in-charge.

S&F in repairs Soap dish fixed with Chromium plated brass screws complete all as specified and directed by Engr-in-Charge

S&F PVC connectons 15 size with PTMT nuts (length 600mm) complete all as specified and directed.

S & F in repair towel rail 600mm long or PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (min wt 190 Grm) complete all as specified and directed by Engr-in-charge.

S&F in repair 20mm PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and directed by Engr-in-charge.

S&F in repair 25mm PPR ball (brass insert), conforming to ISO 2000 screw down end for PPR pipe or for union and fixed complete for size of 20mm bore all as specified and directed by Engr-in-charge.

M & L 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregated) as in flooring and finishing surfaces to receive tiles complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (light shade) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and screed bed 15mm thick in CM 1:4 for laying floor tiles all as specified and directed.

M&L for 75mm bore PVC (SWR) Junction single (Single T) Equal or unequal complete all as specified and directed by Engr-in-Charge.

M & L for providing and fixing 6 mm thick prelaminated board as in ceilings fixed with screws as per manufacturers instructions including anodised aluminium powder coated snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ 'T' (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design complete all as specified and directed by Engr-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and directed by Engr-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long - 01 Nos, hinges type B-21 100mm long - 02 Nos, suitable handle - 01 Nos etc in each shutter complete all as specified and directed.

M&L for 3 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed by Engr-in-Charge.

M&L for 12 mm thick Prelaminated particle board, interior grade, prlaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work or aluminium door or windows etc complete all as specified and directed by engr-in-Charge.

S&F in repair Door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of up to 700 mm in width and weight not more than 35 Kg and fixed complete all as specified and directed.

M&L for wind ties as in framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel' complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors and gates of any description.

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as spfd and directed by Engr-in-Charge.

M&L for Point wiring complete with 1.5Sq.mm nominal area of copper conductor FRLS multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC Casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead all as specified and directed for the followings:-

One light/exhaust fan/Bell point point controlled by one way switch

One 3 pin socket out let 5 Amp on independent board complete all as specified and directed.

One 3 pin socket out let 5 Amp on the same board with other switches complete all as specified and directed.

M&L for point wiring for 3 pin 15 Amps socket outlet independent with FRLS copper conductor cable PVC insulated multistandard 2.5 sqmm with incl one run of 2.5 Sqmm PVC copper conductor cable for earth continuity connected to earth dolly and including PVC casing caping fixed on wall including PVC box 2mm complete all as specified and directed by Engr-in-Charge.

Supply and replacement of socket outlet flush type 3/5 pin, pole 5/6 Amps 230 volts one way complete all as specified and directed.

Supply and replacement of Switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed.

Supply and fixing in replacement of switch Socket combination 5 pin 5 & 15 Amps flush type 230 volts complete all as specified and directed.

Supply and fixing in replacement of switch Socket combination flush type 3/5 pin 5/6 Amps 230 volts complete all as specified and directed.

Supply and replacement of Ceiling rose, surface Bakelite three terminals complete all as specified and directed.

Supply and replacement of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F in replacement of old U/S decorative durable LED batten fitting of 18W/20W , 4 feet long with decorative and caps, powder coated CRCA decorative for LED tube of any capacity, 4 feet long (white colour) tube having driver ,connector block etc complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core all as required at site or directed by Engr in Charge.

S&F in replacement of LED lamp 7 /9 Watt, 230volts 50 Hz AC complete all as specified and directed.

S&F in replacement of bulk head fitting 6.5 watt LED complete all as specified and as directed by Engr-in-Charge. Make as per PS.

Supply and fix in replacement of sheet metal enclosure SPN for DBs double door when MCB's to be used single pole & neutral 240 Volt 8 Ways all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of MCB SP 5 to 32 Amp 240 Volts AC ISI marked all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of MCB SPN 40 to 63 Amp 240 Volts AC ISI marked all as specified and directed by Engr-in-Charge.

S&F 36W 2'x2' recess mounting low depth White LED luminairies white powder coated CRCA sheet housing LEDs front frame with translucent cover fixed to the housing fixed in front frame 36W LED extruded aluminium heat sink projected in false ceiling and connection of 3 core coppper wire with all acessessories complete all as specified and directed by Engr-in-Charge.

M & L for Sub main wiring with two run of 6.00 Sqmm (2x6 Sqmm) 1100 volts grade single core FRLS PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x6.0 sq. mm + 1x 6.0 sq. mm unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6.00 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6 Sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit.

Supply and Fixing in Replacement LED bollard light water proof fully heavy metal built warm white (Garden Light) and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and Fixing in Replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rosecomplete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm, 2 core complete all as specified and directed by Engr-in-Charge.

R B TRADERS

M/S RIGDOL CONSTRUCTION

M/S Praveen Kumar and Sons