PROVN OF GALVALUME SHEET AND FLOORING AT STATION CAFETERIA AND IMPROVEMENT UPGRADATION TO STATIC WATER TANK AND UPGRADATION OF BLDG NO P 94 P 95 AT AF STN CHANDINAGAR

Amount

Surface dressing n. exc 15 cm deep in soft/loose soil complete all as specified and directed by Engr-in-Charge

Excavation in post holes each n.exc 0.5 Cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25Cm watering and removing surplus soil to a distance n.exc 50m and making good surface in soft/loose soil complete all as specified and directed by Engr-in-Charge

M&L for cement concrete 1:3:6 type C1 (Using 20mm graded stone agrregate ) as in foundation of posts, railing and similar work complete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class "B" brick (using old size bricks)straight or curved on plain exc 6m mean radious built in cm 1:6 complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:6) on brick wall or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed by Engr-in-Charge

Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a thin layer of wall care putty complete all as specified and directed by Engr-in-Charge

S&F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flate sections) including distance pieces, cleats etc conforming to Fe410-W (Gde-E-250) quality-A complete all as specified and directed by Engr-in-Charge

Prepartion of steel surfaces over 10 Cm width or girth and applying two coats of synthetic enamel paint over coat of red oxide zinc chrome primer complete all as specified and directed by Engr-in-Charge

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed by Engr-in-Charge

M&L for providing cement concrete 1:4:8 type D2 (Using 40mm graded stone aggregate) , 100mm thick as in sub base in floor/paving etc complete all as specified and directed by Engr-in-Charge

M&L machine cut kota stone slab flooring 18-20mm thick over and including 15mm thick screed bed of cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engr-in-Charge

Demolition cement concrete in ground floor and paving n. exc 15 cm thick below or above ground level complete all as specified and as directed by Engr-in-Charge

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar complete all as specified and as directed by Engr-in-Charge

Taking down cement or cement lime plaster on brick or stone walls including raking out joints/hacking for key, scrubbing down with water etc complete all as specified and as directed by Engr-in-Charge

Material supply only MS galvanised chain link fencing any size or type complete all as specified and as directed by Engr-in-Charge

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards rails, straining bolts, etc, including provision of binding wire complete all as specified and as directed by Engr-in-Charge

M&L for rendering 10 mm thick in CM 1:6 backing coat and 5mm thick in CM 1:4 mixed with water proofing compound as finished coat on brick wall surface to be finished even and smooth without using extra cement on fair faces of brick wall complete all as specified and as directed by Engr-in-Charge

Supply only water proofing compound approved make complete all as specified and as directed by Engr-in-Charge

M&L for preparation of old surface and applying one coats of painting with synthetic enamel paint on old steel surface complete all as specified and as directed by Engr-in-Charge

M&L for PCC 1:3:6 type C2 (using 40 mm grade aggregate) 75 mm thick as in pavings finished even and smooth top layer and as directed by Engr-in-Charge

M&L 80mm thick machine pressed pre cast concrete interlocking paver blocks any shape and size (M-40) grade with grey cement and pigment of approved design & pattern as approved by GE, laid over & including 25mm thick layer of sand complete all as specified and as directed by Engr-in-Charge

M&L sand filling under floor on in foundation in layers not exceeding 25cm each layer including watering and well ramming complete all as specified and as directed by Engr-in-Charge

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed by Engr-in-Charge

Material and labor for cutting chasis and point wiring with 1.5 sq mm PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 Volts grade, drawn through and including 19 mm / 20 mm dia rigid non-metallic PVC concealed conduit (medium grade) along with 1.5 sq mm continuous PVC insulated unsheathed solid/stranded copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in pressed steel sunken boxes (having wall thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type, covered with 3.0 mm thick bakelite sheet (Make: Hylum or equivalent) for mounting switches, sockets, fan regulators etc including testing on completion complete making good the disturbed surface complete all as specified and as directed by Engr-in-Charge. (a) One light/ fan point controlled by one switch.

All as per item No 25 but One 3 pin socket outlet, 5 Amps independent socket controlled by one switch complete all as specified and as directed by Engr-in-Charge.

All as per item No 25 but One 3 pin socket outlet, 5 Amps on the same board with other switches complete all as specified and as directed by Engr-in-Charge

All as per item No 25 but One bell point controlled by one push button on the same board with other switches or independent complete all as specified and as directed by Engr-in-Charge

All as per item No. 25 above but with 2.5 sqmm cable for one three pin 15 Amps socket out let controlled by one switch complete all as specified and as directed by Engr-in-Charge Note:- (For item No 24 to 29) Cost making good disturbed surface below existing point wiring taken out vide item No 25 and cutting chases and making good of disturbed surfaces by cement & sand mortar (1:3) and surface finish as per adjustment surface conduit and all accessories as required for concealed point wiring vide item No 24 to 29 as applicable shall be deemed to be included in the unit rate quoted against these items.

Supply and fixing switch socket combination 2-in-1, 5 Pin, 15 Amps, flush type complete all as specified and as directed by Engr-in-Charge

Supply and fixing switch socket combination 2-in-1, 5 Pin, 5 Amps, flush type complete all as specified and as directed by Engr-in-Charge

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified and as directed by Engr-in-Charge

Supply and fixing switch piano flush type, single pole one way 5 Amps 230 Volts complete all as specified and as directed by Engr-in-Charge

Supply and fixing bell push, flush type, 5 Amps complete all as specified and as directed by Engr-in-Charge

Supply and fixing ceiling rose, surface bakelite with three terminals complete all as specified and as directed by Engr-in-Charge

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engr-in Charge

Single pole and neutral enclosure with a two pin and earth plug top and socket complete with one single pole 20 Amps MCB 230 volts complete all as specified and as directed by Engr-in-Charge

S&F of LED tube light fitting single tube, industrial battern CRCA body along with 20W LED tube surface mounted complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engr-in-Charge

S&F LED Bulb 9W, 230 volt complete all as specified and as directed by Engr-in-Charge

Supply & fix bulk head fitting with 10 Watt LED Lamp complete all as specified and as directed by Engr-in-Charge

S&F connecting up testing and commissioning highly efficient LED security light with lense made up of presure die castaluminium housing and enclosed with toughned glass IP 66 of capacity 45W 230 Volts complete all as specified and as directed by Engr-in-Charge of Make: Halonix Cat Ref No. HLSLD-14-45-CWL

S&F bell Ding Dong AC. 230 volts, single pole complete all as specified and as directed by Engr-in-Charge

Supply & Fixing of exhaust fan 250mm sweep with louvers including fixing material grouting of bolts in wall and cutting of walls for making hole/brickwork/masonarywork and make the disturbed surface good as per existing wall complete all as specified and as directed by Engr-in-Charge

Supply & Fixing of water hater (geyser) 25 ltrs capacity including mounting on board supply and connecting inlet and outlet pipes to existing water supply pipe line with suitable size fastener and associated works complete all as specified and as directed by Engr-in-Charge

Supply & Fixing of Meter box sheet metal enclosure concealed type made of metal of size 32 x 25 x 14 cm having suitable incoming and outgoing openings for cables complete all as specified and as directed by Engr-in-Charge

S&F Sheet metal enclosure DB 12 way double door with 200amps rated bus bar complete all as specified and as directed by Engr-in-Charge

S&F Sheet metal enclosure DB 4 way double door with 200amps rated bus bar complete all as specified and as directed by Engr-in-Charge

S&F Isolator Double pole 40A complete all as specified and as directed by Engr-in-Charge

S&F MCB SP 6-32 Amp, 10 KA, 230 Volt complete all as specified and as directed by Engr-in-Charge

S&F Wiring for circuit/submain wiring alongwith earth wire of 2x4.0 sq. mm and 1x2.5 sq. mm earth wire sizes of FR PVC insulated copper conductor, single core cable in surface/recessed in PVC conduit complete all as specified and as directed by Engr-in-Charge

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below round level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point complete all as specified and as directed by Engr-in-Charge or indicated including testing on completion

Taking down old roof treatment in any description incl scrube and loose concrete, plaster, bitumen, oil grases and any other materials that might effect adhesion by wire brushing the surface and cleaning of the surface throughly with water and disposed off old materials complete all as specified and as directed by Engr-in-Charge

Providing water proofing treatment to old RCC roofs surface with polymer based liquid water proofing solution by using any of the following proprietary products or equivalent approved by E-in-C’s branch all as directed. Notes:- 1. List of products (a) Brushbond roofgaurd manufactured by M/s Fosroc Chemicals (India) Pvt Ltd. (b) Dr. Fixit New Coat manufactured by M/s Pidilite Industries Limited. (c) Sikalastic – 560 in combination with Sikafab1 or Sika Reemat manufactured by M/s Sika India Pvt Ltd. 2. Removal of existing roof treatment shall be measured and paid separately vide item No 1 here-in-above.

Note:- Item No 2 Contd…/- 3. All the listed products are of proprietary nature and shall be applied strictly as per manufacturer instructions in 3 coat system. The work shall be executed through authorised service representative of the manufacturer after obtaining approval from the GE by providing requisite proof of service representation of the manufacturer. All works shall be carried out in presence if the authorised representative of the department entreated with the work. Record in this regard shall be maintained. 4. Mixing of two brands in single location is strictly prohibited. 5. Primer to be applied before applying roof treatment coating shall be of the same manufacturer as per manufacturer advice. Requisite repair to subcrete, if necessary, shall be done as per manufacturer instruction and cost thereof shall be deemed to be included in the quoted rate.

Note:- Item No 2 Contd…/- 6. Screed bed in CM (1:3) shall be applied over top coating (3rd coat) which will be measured and paid separately under item No 3 here-in-after. However clean dry coarse sand shall be sprinkled over top coating before providing the screed and cost of the same shall be deemed to be included in unit rate quoted against this item. 7. Before commencement of the work, a brochure containing details of the product and application process duly certified by the manufacturer shall be submitted for record purpose. The contractor shall also be responsible to produce Purchase Voucher of total quantity of the proprietary materials incorporated in this item before claiming any payment. No payment against item No 2 and 3 shall be allowed in parts for the quantity involved in a single building and also before satisfactorily water tightness test is carried out on ground.

Note:- Item No 2 Contd…/- 8. The contractor shall furnish a guarantee for effectiveness of roof treatment work for a period of 10 years from the date of completion of this contract and shall be responsible to redo the complete roof treatment work for the complete building (if any leakage/seepage is noticed in any building receiving the treatment within the guarantee period) without any extra cost to the Government by complete removal of the executed roof treatment work (item No 2 and 3 of Sch ‘A’/BOQ) and stand guarantee for further 10 years from the date of physical completion of the roof treatment repair work. An amount equal to 2.50 % (Two Point Five Zero Percent) of the total cost of roof treatment work executed (item No 2 & 3 of Sch ‘A’/BOQ) subject to a minimum amount of Rs 5,000/- shall be retained from the final bill of the contractor a security deposit against efficacy of roof treatment which shall be released after expire of the guarantee period subject to no defect is notified to the contractor within the guarantee period. However, if any rectification work is notified to the contractor but not attended by the contractor, within the stipulated guarantee period, the total amount of security deposit shall be forfeited and shall be at the disposal of the President of India. No claim whatsoever on this account shall be entertained at a later date.

Note:- Item No 2 Contd…/- 9. Further, in the event of any rectification work carried out by the contractor, the security deposit shall continue to be retained by the department till expiry of a period of 10 years from the date of completion of rectification work. This additional period shall be known as extended guarantee period. However, this extended guarantee period shall not be applicable for the work in building not notified for rectification work within the original guarantee period of 10 years from the date of completion of the contract. 10. Same procedure as required for release of Performance Security deposit shall be applicable for seeking release of the security deposit against roof treatment work after expiry of guarantee period/extended guarantee period (as applicable for the instant case). 11. The contactor may, if so desired, furnish the guarantee amount in the same format as applicable for the performance security deposit.

M&L for Rendering 10mm thick on concrete surfaces in CM 1:3 with liquid WPC and finishing the surface fair and even complete all as specified and as directed by Engr-in-Charge

M&L for Non-skid Ceramic colour tiles of size 400mmX400mmX7 to 8 mm thick in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer or mortar 15 mm thick for laying floor finished in CM 1:6 incl dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for Glazed Ceramic colour tiles in vertical surfaces of size 450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl backing coat or bedding layer or mortar 10 mm thick for vertical surfaces in CM 1:4 incl dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge

M&L for Rendering 15mm thick in cement mortar 1:4 in two coats (10mm thick under coat & 5mm thick finishing coat) on fair faces of brick work or concrete surfaces in CM 1:4 and finishing the surface fair and even including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge.

M&L for Rendering 15mm thick in cement mortar 1:4 in two coats (10mm thick under coat & 5mm thick finishing coat) on fair faces of brick work or concrete surfaces in CM 1:4 and finishing the surface fair and even incl taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 and finishing the surface fair and even incl taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge

M&L for Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM 1:3 and finishing the surface fair and even incl taking down cement plaster on brick, concrete or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by Engr-in-Charge

S&F for Mild steel, plain, black sheet 1.25mm in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed by Engr-in-Charge

Taking down chowkats or frames not exc1.5 Sqm each with shutter (without taking off shutter form the frame) complete all as specified and as directed by Engr-in-Charge

–ditto- but exc 1.5 Sqm but not exc 4 Sqm each complete all as specified and as directed by Engr-in-Charge

S&F for Pressed steel frames of size 125 x 60mm for doors , windows and ventilators etc, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed by Engr-in-Charge

S&F for Pressed steel frames of size 105 x 60mm for doors , windows and ventilators etc, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and as directed by Engr-in-Charge

S&F in opening, solid PVC Frame of size 50mm x 47mm for door made out of 5mm plain colour PVC Sheet reinforced with MS Square tube complete all as specified and as directed by Engr-in-Charge

S&F Factory made 35mm 2nd class hardwood Plain, framed panelled shutters(any No of panels) with panels of timber flat on both side (feather edged) or of veneered particle board medium density wood particle board with commercial face veneers fixed to chowkats complete all as specified and as directed by Engr-in-Charge

S&F Factory made 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as per SSR-Part-I Section-8, Clause 8.24 (a) etc complete all as specified and as directed by Engr-in-Charge

All as per item No 69 but 25mm thick for window, ventilations etc. complete all as specified and as directed by Engr-in-Charge

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC’C’ channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, and bottom rail: on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile and rail with suitable PVC sheet beading, and joined to gather with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed by Engr-in-Charge

S&F 12 mm Prelaminated particle Board , exterior grade pre laminated one side with decorative choice lamination and other side balancing white lamination fixed with nails in pulmet Boxes complete all as specified and as directed by Engr-in-Charge

Preparation of old plastered surfaces and applying one coat of cement base paint in any colours on wall incl washing, rubbing down or by steel wire brushing complete all as specified and as directed by Engr-in-Charge.

Preparation of new plastered surfaces and applying two coats of distemper oil emulsion in any colours on wall over a coat of primer complete all as specified and as directed by Engr-in-Charge

Preparation of old plastered surfaces and applying one coat of distemper oil emulsion in any colours on wall incl washing, rubbing down or by steel wire brushing complete all as specified and as directed by Engr-in-Charge

Preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed by Engr-in-Charge

Preparation of old plastered surfaces and applying one coats of white wash on ceiling including washing, rubbing down or by steel wire brushing complete all as specified and as directed by Engr-in-Charge.

Preparation of new steel surfaces in any description not other wise described over 10cm width or girth and applying two coat of synthetic enamel paint in any colours over coat of red oxide zinc chrome primer complete all as specified and as directed by Engr-in-Charge

Preparation of new surfaces of wooden any description not other wise described over 10cm width or girth and applying two coat of synthetic enamel paint over coat of primer complete all as specified and as directed by Engr-in-Charge

All as per item No 79 but preparation of old surfaces and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge

S&F 3mm thick sheet glass, ordinary quality and glazing fixed with beading complete all as specified and as directed by Engr-in-Charge

S&F for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed by Engr-in-Charge.

S&F Butt hinges 100 mm long aluminium alloy anodised and fixed complete all as specified and as directed by Engr-in-Charge

S&F 150mm aluminium extruded alloy handles fabricated type complete all as specified and as directed by Engr-in-Charge

S&F 100mm aluminium extruded alloy handles fabricated type complete all as specified and as directed by Engr-in-Charge

S&F 150 mm alumunium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-Charge

S&F 100 mm alumunium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-Charge

S&F 300 mm long aluminium alloy anodised, sliding door bolt with hasp ,staple(bolt type) and fixing clips of sheet cast of extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge

S&F Tubular towel 20mm dia D type 60 CM long between flanges, aluminium anodised complete all as specified and as directed by Engr-in-Charge

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engr-in-Charge

S&F Vitreous China wash basin pedestal pattern, white flat back in any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed by Engr-in-Charge

S&F for 10 litres capacity PVC valve less, symphonic action type flushing cistern; low level, white, with inlet, ball valve, float and handle including bracket complete all as specified and as directed by Engr-in-Charge

S&F for Aluminium harrison curtain rail with fixing brackets, stops, rollers etc complete all as specified and as directed by Engr-in-Charge

S&F for 20mm dia medium grade galvanized water tubing with all necessary fittings and fixed complete walls incl taking up or down steel water tubing galvanised complete all as specified and as directed by Engr-in-Charge

All as per item No 95 but 15 mm dia complete all as specified and as directed by Engr-in-Charge

S&F Rotetional moulded HDPE water storage tanks (cylindrical vertical with closed top three layer type) of Capacity in litres 500, hoisted and fixed in postion derected by Engr-in-Charge

S&F for Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests,traps, bends etc (excluding flushing cistern and flush pipe) fixed in repairs complete all as specified and as directed by Engr-in-Charge

S&F Pillar taps fancy type cast copper alloy with capstain heads chromium plated screwed down high presser, with or without lettered’ hot or clod ‘ with long screwed shanks and fly – nuts, screwed for iron pipe and fixed in repair to 15mm dia complete all as specified and as directed by Engr-in-Charge

S&F Stop valves cast copper alloy screwed down high pressure with crutch on butterfly handle screwed both ends for union and fixed in repair to 15 mm dia complete all as specified and as directed by Engr-in-Charge

All as per item No 100 but fancy type chromium plated with long shank and cup concealed type 15 mm dia complete all as specified and as directed by Engr-in-Charge

S&F Bib taps fancy type cromium plated alloy with crutch or butterfly, Handle, Screwed down, screwed for Iron pipe or for brass ferrule and fixed in repair to 15 mm dia complete all as specified and as directed by Engr-in-Charge

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in repair. (Minimum weight 15mm-142gms/2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed by Engr-in-Charge

S&F PVC connection 15 mm size with nuts of length 600 mm complete all as specified and as directed by Engr-in-Charge

S&F for Brass chromium plated shower rose 125 mm fixed in repair complete all as specified and as directed by Engr-in-Charge

S&F PVC (SWR) single socketed Rain water pipe 110mm bore (OD) in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-Charge

All as per item No 106 but 75mm dia complete all as specified and as directed by Engr-in-Charge

S&F PVC (SWR) bends of 110mm dia complete all as specified and as directed by Engr-in-Charge

All as per item No 108 but 75mm dia complete all as specified and as directed by Engr-in-Charge

36SHRI RADHEY ASSOCIATES

H.B. Traders

imran construction company