SPECIAL REPAIR TO BLDG NO EOR-27 (08 Qtrs) AND SPECIAL REPAIR FOR REPLACEMENT OF LT OVER HEAD LINE TO LT UG CABLE AT CERTAIN LOCATION AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting/vertical surfaces etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 10mm thick screed bed in CM (1:4), complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:4), complete all as specified and and as directed.

Dismantling of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc., complete all as specified and as directed.

M&L for granite (of any type) 18 to 20mm thick (Table rubbled and polished ) in skirting,kitchen plateform/dado etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in flooring, laid over and including 20mm thick screed in cm (1:6), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed.

M&L for 20 to 25mm thick Machine cut kota stone slabs as in riser of step, skirting, dado etc. laid over and including 10mm thick backing layer in cm (1:4), set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed .

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary provision of lugs, locks strike plate, hinges etc, applying one shop coat of Zinc Chromate primer after prepation of the surfaces, complete all as specified and as directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing and as directed. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life .

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & show on drawing for SI NO 8101 on Sr. Page No181 of SSR Part -II and as directed.

S&F Factory made 30mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and as directed.

S&F Factory made 25mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides, one face iscovered with decorative face veneer with lipping/frame to match, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F standard aluminium anodised aluminium section as in frame, shutters for doors, windows / ventilators, Fixed/ Openable / side hung/ sliding two or three track or in any pattern, partitions, kitchen cabinet/almirah etc, cut to size, jointed with cadmium plated steel screws, including Aluminium beading & rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered for payment. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth shall be measured and paid separately under respective items.

S&F 4mm thick plain sheet glass of frosted one side and and glazing for Aluminium Joinery, in squares exc 0.50 sqm in each pane, complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 200 mm long of extruded section, complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt, 100 mm long of extruded section, complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S&F 150 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

S&F ball catches with 8mm dia steel ball, and brass body for cupboard shutter and striking plate including letting in and fixed, complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings), complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering/ cladding to wall fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to aluminium frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process. (ii) Aluminium frame work shall be measured and paid for separately.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteneners 12.5mm dia and 40mm long, complete all as specified and as directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F mild steel rolled sections & plates [Fe 410-W (Gde E-250) quality - B] as in main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, hold-fasts, lugs, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 41 above but 20 mm bore

All as per item No 41 above but 25 mm bore

Supplying and laying of 20mm (Outer Diameter) of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings,on the walls & ceiling or laid in floors, complete all as specified and as directed.

Supplying and laying of 25mm (Outer Diameter) of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings,on the walls & ceiling or laid in floors, complete all as specified and as directed.

Supplying and laying of 32mm (Outer Diameter) of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings,on the walls & ceiling or laid in floors, complete all as specified and as directed.

S&F of 20mm (Outer Diameter) of CPVC brass elbow, complete all as specified and as directed.

S&F of 25mm (Outer Diameter) of CPVC brass elbow, complete all as specified and as directed.

S&F of 20mm (Outer Diameter) of CPVC brass Tee, complete all as specified and as directed.

S&F of 20mm (Outer Diameter) of CPVC male brass threaded adep (MTA/MBTA), complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tank 500ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 210 grms), complete all as specified and as directed.

S&F hard drawn steel wire fabric (weight not exc.4kg/Sqm) cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) as in benching, cover fillets, roof kerbs, kerbs PCC padding over roof and of any description & in any position not otherwise specifically provided-for, including taking down existing un-servicable waterproofing treatment from roof slab surfaces, roughening of old concrete surfaces by picking, cleaning the surfaces by wire brush and also including disposing off the retrieved debris outside the premises / site, complete all as specified and as directed by Engineer-in-Charge.

M&L for 40mm thick cement concrete type B0 (1:2:4) (Using 12.5 mm crushed stone aggregates) admixed with admixture Conplast WL Xtra (of Make FOSROC or equvilant brand of other manufracturer) at the rate of 125ml/ 50 kg Bag of Cement and Vergin ploypropylene Fibre (Recron) (of Make RELIANCE or equvilant brand of other manufracturer) at the rate of 125gm per 50 kg Bag of Cement, as in padding over roof etc, finsihed even and smooth without using extra cement, complete, all as specified and directed by Engineer-in-Charge under the guidence of authorised applicator of the manufracturer.

M&L for waterproofing coating with polyurethane based water proofing liquid membrane to be applied by brush with three coats miniumum dry film of total thickness 1mm thick and shall be cured by reaction with atmospheric moisture to give a tough elastomeric waterprrofing memebrane, complete all as specified and and as directed by Engineer-in-Charge. Note: Item No. 50 shall be excuted through authorised applicator of the manufacturer as approved by GE.

Coving treatment to be done at all junctions of coving size (50mm X 50mm ) with Nitobond SBR latex (of Make FOSROC or equvilant brand of other manufracturer) to be mixed with cement, complete all as specified and and as directed by Engineer-in-Charge.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for brick work with fly ash Bricks, straight or curved on plan to any radius built in CM (1:4) as in half brick thick walls, complete all as specified and as directed.

M&L for Brickwork with fly as Bricks, straight or curved on plan exc 6m mean radius built in Cement morter (1:6), complete all as specified and directed

S&F in repair vitreous china wash basin, 1st quality, white, flat back, approx size 550x400mm excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repair sink made of 0.80 mm thick sheet of stainless steel (Bronze range super steel 204 : Matt) for kitchen or laboratory with and including plugs, washers, 40mm bore brass chromium plated waste fittings, 40mm bore PVC waste pipe, also including bedding in cement mortar (1:3) on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 495mm x 420mm x 178mm with bowl size 405mmx 355mm, complete all as specified and as directed.

S &F stainless steel kitchen plate rack of overall approx size 24’’ x 36’’ x 10’’, complete all as specifiied and directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, , white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, complete all as specified and as directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed.

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints (including Shower Arms) to 15mm bore steel pipe or union, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, long swan neck, cast copper alloy, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed.

S & F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed.

S&F in repair angle cock/stop cock, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed.

S&F in repairs Pillar taps with Aerator, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm, complete all as specified and directed.

Supplying and laying of 32mm bore low density polyethylene (LDPE) pipe of pressure rating 6kgf/sq .cm, on the walls & ceiling or laid in floors including taking down of old ones, complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 75mm (diameter of outlet), plain with grating including jointing with solvent cement, complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and as directed.

S & F in repair 75 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints laid in floors/ trenches etc, complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints laid in floors/ trenches etc, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends (any radius), disminishing pieces or tapers complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends (any radius), with oval access door disminishing pieces or tapers complete all as specified and directed.

S&F 75mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary standard PVC stay clamps etc, complete all as specified and directed. Notes : (i) Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM (1:3) to match with the existing surfaces.

S&F 110mm bore PVC (SWR) bends (any radius), disminishing pieces or tapers complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) of any description & in any position, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded chrushed stone aggrgates) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded crushed stone aggrgates) as in slabs supported on walls, beams and and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. Note :- Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded crushed stone aggrgates) as in Chajjas, complete all as specified and directed. Note: Reinforcement and Form work shall be measured and paid for seperately.

M&L for prelaminated particle board 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

M&L for cement concrete (1:2:4) type, B1 (using 20 mm graded crushed stone aggregates) as in copings, Chajja, kerbs, roof padding, staging of water tank, for sealing of chases for fixing of pipes upto DB etc, including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

S&F in repair mild steel helical door spring 300mm long, ordinary rat tail rod pattern springs including roller and roller plate fixed with screw to wooden frame or with welding to steel frame, complete all as specified and as directed.

M&L for brushing neat cement slurry with 1.00 kilogram of cement per square metre over roof surfaces etc, providing 20 mm thick plastering in cement mortar (1:3) mixed with liquid water proofing compound, finished even and smooth, complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid separately under the respective Item.

M&L for applying evenly bituminous tack coat @ 1.20Kg/Sqm of industrial bitumen blinded with 0.006 cum of coarse sand per Sqm on the surfaces of the sunken floor , complete all as specified and as directed.

M&L for cement concrete (1:5:10) type E-2 using 40mm graded brick aggregate as in sunken portion of WC etc, complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

Cutting chases, pinning in. making good to facings of brickwork, where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for oncealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth , complete all as specified and as directed.

S&F in repair stainless steel decorative curtain rod of 25 mm bore with wood finishes, complete all as specified and as directed.

S&F brackets and fancy type funnel caps suitable for the curtain rod to be provided under item No 105 above, complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls, applying two coats of wall care Putty (minimum thickness of two layers shall be 1.5mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment from the internal surfaces of wall etc, applying two coats of wall care Putty (minimum thickness of two layers shall be 1.5mm) and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white washing, complete all as specified and directed .

M&L for washing, rubbing down and stopping of painted surfaces thereafter preparation of plaster or unplaster surfaces ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

M&L preparation of old painted surfaces of wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces of any description duly applied with shop coat of primer, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in this item.

M&L preparation of old painted surfaces of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of newly surfaces of walls, applying one coat of cleaning solution to prevent future fungal growth, thereafter applying two coats of wall care Putty (minimum thickness of two layers shall be 1.50mm) and Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm, complete all as specified and directed.

M&L for complete removal of existing treatment from the old decorated surfaces of walls, preparing the surfaces, applying one coat of cleaning solution to prevent future fungal growth, thereafter applying two coats of wall care Putty (minimum thickness of two layers shall be1.50mm) and Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqmr, complete all as specified and as directed.

M&L for second class hard-wood in scantlings as in timber framed and fixed clean swan including dismantling, complete all as specified and as directed.

M&L for second class hard-wood plain fillets sectional area exc 3 sq.cm and n.exc 6sq.cm as in square,rectangular or tringular in section, clean sawn, secure with nails or brads including dismantling, complete all as specified and as directed.

S&F 15mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, laid in trenches and including taking down of old one, complete all as specified and as directed.

S&F 20mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, laid in trenches and including taking down of old one, complete all as specified and as directed.

S&F 25mm bore medium grade, galvanised steel tubing (including in short lengths) with and including all fittings, laid in trenches and including taking down of old one, complete all as specified and as directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 50 mm bore, complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 40 mm bore, complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 25 mm bore, complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 15 mm bore, complete all as specified and directed.

Taking down carefully existing aluminium point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

M&L for point wiring for one light point/ one fan point/ one exhaust fan controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces , complete all as specified and as directed.

All as per item No.130 here - in - before but for one light point controlled by two, 2- way switch with 1.5 sq mm single core mulistandered copper conductor cable (FRLSH) alongwith 1.5 Sqmm continious PVC insulated unsheathed single core multisheaded copper conductor (FRLSH) cable for earth continuty wire, complete all as specified and directed.

All as per item No 130 here-in-before but for one socket with other switch/switch socket outlet 5 amps on the same board, complete all as specified and as directed

All as per item No 130 here-in-before but for one 3pin 5 Amp switch socket outlet, indepent board 1.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

All as per item No130 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

S&F switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

S&F switch piano flush type, single pole, one way, 15 amps, complete all as specified and as directed.

S&F switch piano flush type, two way, 5 amps, complete all as specified and as directed.

S&F switch socket , 2 in 1, 5pin, 5 Amp, complete all as specified and as directed.

S&F switch socket outlet, 2 in 1,6pin, 5 and 15 amp, complete all as specified and as directed.

S&F ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

S&F electronic fan regulator, flush type (Delux model), rotary step type, 5 step, not less than 100 watt, complete all as specified and directed.

S&F call bellding dong, 230V single pole, complete all as specified and directed.

S&F Bell, AC, 230volts, single pole, complete all as specified and as directed.

M&L for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLHS cable of size 6.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces and including taking down old one, complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

S&F sheet metal enclosure for MCBs DBs, TPN, 4 way with 200Amps rated bus bar 240 volts, Double Door with magnetic locking system, Powder coated including necessary provision for inserting the DBs in wall by cutting the bricks/stone masonary etc and making good of disturbed surfaces to match with existing colour of wall, complete all as specified and as directed.

S&F sheet metal enclosure for MCBs DBs, SPN, 12 way with 200Amps rated bus bar 240 volts, Double Door with magnetic locking system, Powder coated including necessary provision for inserting the DBs in wall by cutting the bricks/stone masonary etc and making good of disturbed surfaces to match with existing colour of wall, complete all as specified and as directed.

S&F sheet metal enclosure for MCBs DBs, SPN, 8 way with 200Amps rated bus bar 240 volts, Double Door with magnetic locking system, Powder coated including necessary provision for inserting the DBs in wall by cutting the bricks/stone masonary etc and making good of disturbed surfaces to match with existing colour of wall, complete all as specified and as directed.

S & F MCB, 'C' curve, TPN, 240 volts breaking capacity 10KA, 40 to 100 Amps, breaking capacity 10KA, complete all as specified and directed.

S & F MCB, 'C' curve, SPN, 240 volts breaking capacity 10KA, 40Amps, breaking capacity 10KA, complete all as specified and directed.

S & F MCB, 'C' curve, SP, 240 volts breaking capacity 10KA, 5 to 32Amps, breaking capacity 10KA, complete all as specified and directed.

S &F for wall mounted LED tube lingh fitting 10 watts batten for surface, anodized extruded aluminium housing, high transmisivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories interially pre-wired and necessay mounting arrangements, provision of new 3 core multistranded copper counductor of size 23/0.193 form ceiling rose to fiting complete all as specified as directed.

S &F for wall mounted LED tube lingh fitting 20 watts batten for surface, anodized extruded aluminium housing, high transmisivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories interially pre-wired and necessay mounting arrangements, provision of new 3 core multistranded copper counductor of size 23/0.193 form ceiling rose to fiting complete all as specified as directed.

S & F in repair energy saving new generator enviromental friendly long life versatile presure die cast aluminium IP 66 for securty ligh fitting luninaire with high power LEDs as ligh source (100 Im/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre-wared and necessary mounting arrangements and provison of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade braket 1.5 mtr long bend to requred shape with clamps, nut botls including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer , complete all as directed by Engineer-in-charge.

S & F Decorative wall lingh fixture, brushed nickel finish, suitable for 9 W LED lamp (B22) including 9/10 W LED Bulb etc, complete with all accessories internally pre-wired and including connecting up with twin core twisted fiexible copper conductor cable suitable size, complete all as specified and directed.

S & F replacement light fitting, 1 X10W LED bulk head luminaries IP65, Min- 50,000 burning Hrs. Diffuser made of high grade polycarbonate. High pressure die cast aluminium housing. CCT-5700K, 240 Volt complete with all accessories and including connection up with twin core twisted flexible copper conductor cabe with suiable size of 230V, 50HZ.. Make-Philips/Havells/Crompton/HPL

Taking down ceiling fan/exhaust fan any sweep, keeping with safe custody and refixing the same with replacement of unsv 3core PVC insulated sheathed multistanded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal, complete all as specified and directed by the Engineer-in-charge.

S&F energy saving BLDC ceiling fan; 5 star rating, Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, Voltage- 90-300V AC, 50Hz, single phase, RPM - 340 to 375 rpm, Blades- Decorated, Sweep - 1200 mm, Air delivery - Not less than 210 CMM with service value 6.00 BEE and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE, complete all as specified and as directed.

S & F for energy Exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to esiting brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted).

S & F for energy Exhaust fan of 250 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaut fan for connection and making suitable size of hole to esiting brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaut fan is deemed to be included in overall rate quoted).

S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed.

S&F Single pole and neutral enclosure with & including a two pin and earth plug and socket, also with and including one number single pole, MCB, 20 Amps, 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 40 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, including dismantling old unsv ones complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,laying of cable, pipe etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out, complete all as specified and directed.

Returning, filling in, including spreading, watering and well ramming in layers not exc 25cm thick in layers, complete all as specified and directed.

Removal of surplus spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Dismantling of ACSR or AAC conductor , complete all as specifed and directed.

Dismantling of cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, complete all as specified and directed.

Dismantling of insulators of any grade, description and size from the poles etc, complete all as specified and directed.

Dismantling of GI earth wire or copper conductor, service feeder or distribution span, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanized steel strip, heavy duty, wire armoured electric LT power cable with stranded aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm x 4 core in trenches /along poles/on wall etc, complete all as specified and as directed Notes : - (i) Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately. (ii) Unless otherwise directed by the GE, the cable shall be procured by the contractor in single length (as manufactured) to meet the actual length of cable as required at site. However, for payment purpose, the length actually ordered & laid shall be measured and paid for.

All as per item No 170.00 here-in-before but LT Cable of size 16 Sqmm x4 Core.

All as per item No 170.00 here-in-before but LT Cable of size 35 Sqmm x 3.5 Core.

All as per item No 170.00 here-in-before but LT Cable of size 50 Sqmm x 3.5 Core.

All as per item No 170.00 here-in-before but LT Cable of size 70 Sqmm x 3.5 Core.

Material and labour for well burnt Sub-class 'B' old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

M& L for Sand cushioning in trenches for cushioning of underground cable including spreading, levelling, well ramming in layers , complete all as specified and directed. Note: Punned thickness 18cm shall be considered for payment as per para 19.75 of SSR Part-I)

Supply and fixing GI tubing, light grade, 50mm bore for protection of cable under road crossing, across drain, along electric pole or floor /wall etc, complete all as specified and directed. Note for Item No. 177 to 179: Excavation & Earthwork/Boring/ Drilling shall be measured & paid for separately. However the cost for provision of clamps made from mild steel flat of required size, bolts, nuts, washers etc (including painting of mild steel surfaces with 2 coats of aluminium paint over 1 coat of red oxide primer) for fixing of G.I. pipes with poles etc shall be deemed to be included in the quoted rate of above item.

All as per item No 177 above but 40 mm bore tubing.

All as per item No 177 above but 15 mm bore tubing.

M & L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of preparation of exposed surfaces, application of one coat of red oxide primer and thereafter 2 coats of alluminiuam paint, complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, connected to GI strip 25mmx4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, PCC (1:3:6) type C-1 with 50 mm thick Pre-cast RCC (1:2:4) type B-1 cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 40 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 m and necessary testing on completion, complete all as specified and as directed.

Boring/Drilling (horizontally) using ultrasound technique and necessary machine for passing 40mm to 80mm bore pipe for protection of the cable at 1 metre depth in soil below existing road, pavement, hard standing etc without damaging the existing surfaces, getting out & disposal of soil to a distance not exceeding 50 metre from the site of work, complete all as specified and directed. Note : Cost for provision of pipes & cable not included in the scope of above item.

Supply,laying & fixing double wall corrugated (DWC) pipes of size 63 mm outer dia conforming to IS 16205 (Part-24) including all accessories( joints, Sockets, Elbows, bends and End caps etc), all complete as specified and as directed.

Supply, installation, testing and commissioning 3 phase and neutral, 415 volts outdoor type, double door, LT panel board size 1000 mm height X 700 mm width X 500 mm depth (over all dimension) confirming to IS 8623, CPRI approved, factory fabricated & factory assembled , waterproof,dust and vermin proof cubical type with locking arrangement , LT Panel made out of suitable size angle iron, channel and fabricated from 3.00 mm thick CRCA sheet with anti corrosive coating and finally epoxy polyester powder coating of flint Grey shade (RAL-7032), independently housing for each control switch gear and indicating lamps with & including busbars made of pure copper duly insulated with heat retardent fire proof (HRFR) heat shrinkable sleeves of relevant colours.Bus bar shell be properly supported/mounted on epoxy insulators.All live parts and joints shall be insulated with (HRFR) shrouds, conforming to IS, including provn for cable gland and lugs for incoming and out going cable and connecting suitable earth strips .Suitable openable doors shall be provided of all operational switchgear and MCCBs and detchable cover shall be provided on all other accessories. Grouting the panel board in ground with & including suitable size foundation & plinth of PCC 1:3:6 (type C-1 using 20 mm grade crushed stone aggregate) complete.Panel shall be manufactured suitable for housing and including the following duly control wiring with multistranded copper condutor FRLSH with colour coding incl connection with copper lugs complete for 3 phase 50 Hz electric supply. Incoming:-(a) Copper strip busbar of current carrying capacity 200 Amps wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 nos. (b) MCCB 100 Amp, 4 Pole, 415 Volts, 25 KA rating with thermal magnetic trip unit, overload, short circuit fault protection 3 phase, Ics = 100% of Icu and shall have roto operative double break mechanism along total break time less than equal to 10 ms with Spreader terminal of both end side - 01 No. Make: Schneider Cat no - LV510317 / Legrand Cat No: 420055 / Siemens, Cat: 3VA1110-3GE42-0AA0/ ABB, Cat No: 1SDA067406R1.

Supply, fabrication, installation and testing of LT factory made (CPRI approved) water and vermin proof protection pedestal type feeder pillar box of minimum size 900mm x 600mm x 400mm (overalls), outdoor type, double door made out of 3.15 mm thick CRCA sheet with frame and legs of mild steel angle iron of size 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable single higed door/shuter with locking arrangement complete painted with Powder Coated paint of approved shade , including PCC (1:3:6) (type C-1 using 20 mm grade crushed stone aggregate) complete as in foundation of size 0.80m x 0.60m x 0.90m depth (30 cm below ground level & 60 cm above ground level) and connection all outgoing/incomming existing cable of any size drawing/digging out cable from loop in trenches including necessary excavation and earth work complete all as specified and as directed alongwith comprising of the following accessories: Incoming (a) Alluminium bus bar o size 50mmx6mmx400mm long wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 nos. (b) Enamelled iron danger noticed plate of 1.6mm thick mild steel sheet of size 200mmx150mm white with letters, figures, and conventional skull and bones in signal re and fixed with nuts and bolts on door/shutter of JB for LT-01No. Note : For item No. 183 to 186:- The drawings and specifictions of the Panel and its components shall be got approved by the contractor from the GE before procurement.

Supply, providing and testing PVC Insulated, weather proof, FRLSH, PVC sheathed cables with multistranded bright annealed copper conductor of size 1.5 Sqmm 3 core for connection of light fittings to Steel pole light junction box, cable laid through steel pole & including driling work for making hole wire entry in steel pole, complete all as specified and directed.

S&F in repair and testing of factory made thermoplastic weather proof, junction box of size 205(L) x 255 (B) x 112 (D) mm with IP-65 protection having 01 Number DIN Rail for mounting of MC, also provided with 01 Number MCB, SP, 6 Amps, 10 KA breaking capacity, "C" curve & two openings with & including cable glands for termination of cable & fixing with the provision of suitable sized MS clamps etc to poles, complete all as specified and as directed.

S&F in repair street light bracket made out of 40 mm bore GI medium grade pipe 1.2 M length bent to the shape and reduced to size at top upto 1.5m length as required for steet light fittings pronded with two pairs of MS Flat Iron 40mm x 6mm and clamps of required suitable length and shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete, complete all as specified and directed.

CHAKRABORTY AND SONS (BID ID -3172734)

SHRI S K BHATTACHARJEE (BID ID -3174099)

M/S R. K. INDUSTRIES (BID ID -3173282)

MS ORIENT ENGINEERING WORKS (BID ID -3172223)

M/S B D ENTERPRISE (BID ID -3174462)

M/S SEN CONSTRUCTION (BID ID -3173076)

NEO BUILDERS (BID ID -3175257)