REPAIR TO ROOF SHEETS FALSE CEILING FLOORING JOINERIES AND REPLACEMENT OF PLUMBING SANITARY FITTINGS AT TAMULPUR AND DARRANGA MIL STN

Amount

Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc. 4 sq. m each, complete all as specified and as directed by Engineer-in-charge.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each, complete all as specified and as directed by Engineer-in-charge.

Taking down Shutters of any description not exc 1 sq. m each, complete all as specified and as directed by Engineer-in-charge.

Taking down Shutters of any description exc 1 sq. m and not exc 2 sq. m each, complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

M&L for resecuring or easing & adjusting without taking down of aluminium door Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws, aluminium snap beading, rubber gasket, etc. (If required), complete all as specified and as directed by Engineer-in-charge.

M&L for resecuring or easing & adjusting without taking down of wooden door Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws (If required), complete all as specified and as directed by Engineer-in-charge.

M&L for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed by Engineer-in-charge.

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge.

S&F of Solid PVC moulded Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face; complete all as specified and as directed by Engineer-in-charge.

S&F of 35mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides; complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and both faces are covered with decorative face veneer with lipping/frame to match; complete all as specified and as directed by Engineer-in-charge.

S&F of 35mm thick factory made second class hard wood Glazed and skeleton shutters, divided into squares and prepared to receive glass, gauze, etc. with rebated sash bars, edges of framing plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in-charge.

S&F of 30mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters and provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b); complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Anodised aluminium door using 96.6x44.8x1.5mm thick powder coated Anodised aluminium section as in chowkhat, 84.0x44.7x1.5mm thick powder coated aluminium section as in vertical styles and 101.6x44.88x1.5mm thick powder coated aluminium section as in rails, glazing with 5.5mm thick tinted/ black reflective glass exc. 0.5 Sqm in each pane with and including necessary joining cleats, glazing clips, ruber neoprene packing, 200mm long aluminium handles 2 Nos in each door leaf, 100mm long medium grade stainless steel butt hinges of 4 Nos/ leaf, 1 No/ leaf aluminium (extruded section) body Door closer hydraulically regulated suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, 1 No/ leaf aluminium body 150mm long double legged floor door stopper, 1 No brass body 6-lever Mortice lock, vertical type, size 100 mm, anodised aluminum snap beading screws etc., complete all as specified and as directed by Engineer-in-charge. (Note- Cost of powder coated Aluminium section, beads, gasket, glazing and all builder hardware shall deemed to be included in Unit Quoted Rate.)

S&F in-repair of Anodised aluminium three track sliding window and ventilator using 62x29.5x1.5mm thick powder coated Anodised aluminium section as in chowkhat, 38.0x20.0x1.5mm thick powder coated Anodised aluminium section as in shutter, two panel shall be glazed with 3mm thick tinted/ black reflective glass n. exc. 0.5 Sqm in each pane and one panel shall be gauged with 0.56mm thick stainless steel wire cloth with width of apparture 1.18m with and including necessary sliding and locking arrangements, joining cleats, glazing clips, ruber neoprene packing, anodised aluminum snap beading screws etc., complete all as specified and as directed by Engineer-in-charge. (Note- Cost of Aluminium section, beads, gasket, gauge/ glazing and all builder hardware shall deemed to be included in Unit Quoted Rate.)

S&F of 100 mm long Butt hinges, medium weight, stainless steel, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 100 mm long Butt hinges, medium weight, stainless steel, complete all as specified and as directed by Engineer-in-charge.

S&F of 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F of 150 mm long Extruded aluminium alloy handles, febricated type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 150 mm long Extruded aluminium alloy handles, febricated type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F of Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F of 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20 mm dia mild steel, chromium plated curtain rail with fixing brackets, stops, rollers etc., complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Mild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 150 mm Overall length of cover plate, double legged Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and rubber end, fixed in floor, complete all as specified and as directed by Engineer-in-charge.

S&F of 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of aluminium (extruded section) body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hard wood in scantling wrought timber unframed and fixed, including dismantling the existing old damaged scantling, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of second class soft wood plain fillets in square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc. 6sqcm but not exc.13sqcm, complete all as specified and as directed by Engineer-in-charge.

S&F of Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, including dismantling the existing old damaged steel structure,complete all as specified and as directed by Engineer-in-charge.

S&F of TMT bars 8-10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

M&L for Reinforced Cement Concrete, M-20 (Nominal Mix) 1:1½:3, type A-1 (20mm graded stone aggregate) in Columns, pillars, posts, beam, lintel, chajja, cantilever with and including necessary formwork and demolition of existing old damaged RCC structure of any type, complete all as specified and as directed by Engineer-in-charge. NOTE : Reinforcement will be measured and paid separately under relevant Item.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius built and set in cement mortar 1:6, including demolition of the existing old damaged B/W, complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, including demolition of the existing old damaged B/W, complete all as per specified and as directed by Engineer-in-charge.

M&L for Rendering (Internally) 10mm thick in cement morter 1:6 on fair faces of brick work, concrete surfaces, one side of lathing, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering (Externally) 15mm thick in Cement Mortar 1:4 on other than fair faces of brick work, concrete surfaces, other side of lathing, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer-in-charge.

M&L for providing 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and fair and demolition of existing old damaged PCC of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling of existing old damaged tiles of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for Machine cut kota stone slab flooring 14-16mm thick over 20mm thick cement screed base 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including dismantling of existing old damaged stone slab of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Vitrified Ceramic light shade tiles 8 to 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling of existing old damaged tiles of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Glazed ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 300x 450x 7 mm thick, over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match, including dismantling of existing old damaged tiles of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for 20mm thick Granite work (of any type, table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including dismantling of existing old damaged stone slab of any type, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing 40 mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and fair including demolition of existing old unserviceable concrete, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of Synthetic enamel paint (1st quality) of any tint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of Creosote oil, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper oil emulsion of any shade over a coat of chalk whitening, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated steel/iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of black japan paint (1st quality) over a coat of red oxide primer, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of laminated PVC Kitchen Cabinet of 400mm depth made out of 18mm thick one side decorative lamination & other side white lamination sheet & provision of shelves and shutters made out of 18 mm thick one side decorative laminated PVC sheet including all required brackets, SS screws, SS knobs, SS Handles, etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90º edge bent finish, completer all as specified and as directed by engineer-in-charge. (NOTE:- Only front face shall be measured and paid.)

S&F in-repair of solid PVC wall panneling consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement, 5mm thick PVC sheet fillet of width 35mm and fixing at site on PVC frame as per specification, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of exposed powder coated GI snap grid frame work (600x600 mm) for false ceiling comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with suspended hangers of 2 mm dia. G.I. (upto 1200mm length) adjusting level fixed to any type of roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size with and including fixing/ laying/ inserting of pre-painted (white) 4mm thick designer classic E-boards (595x595 mm) to GI frame work, complete all as specified and as directed by Engineer-in-charge.

S&F of 6mm thick asbestos cement, corrugated or semi-corrugated sheets with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc., complete all as specified and as directed by Engineer-in-charge.

S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 4mm thick Asbestos cement plain building boards, fixed to any type of timber frame work with screws, including applying two coats of distemper oil emulsion of any shade over a coat of chalk whitening, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China oval counter top fancy type designer wash basin, white, with brackets, flat back, size 560x400x205mm including cutting for and pinning in ends of brackets or erecting stand including providing 32mm dia CP Waste fittings, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China wash basin, white, with brackets, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including providing 32mm dia CP Waste fittings, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Wash down couple water closet (Cistern mounted) pan and S/P trap of 670x365x740mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Wash down water closet (Pedestal pattern) pan and S/P trap of 540x375x415mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white with and including grating, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long CP brass screws, pointing around urinal back in putty; complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm dia, with and including making necessary connections, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair for 32mm dia PVC flexible waste/ discharge pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 32mm dia PVC flush pipe suitable for flushing cistern, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated Soap Dish of 160x160x90mm in size, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type Brass CP telephonic wall mixer (without hand shower and hose) for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type Brass CP basin mixer without pop up waste for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated shower rose of 125mm dia of rose, fixing to existing pipe or union of 15 mm dia, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type, chromium plated Stop valves/ Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 76 here-in-above, but for 20mm dia GI tubing, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 76 here-in-above, but for 25mm dia GI tubing, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20mm dia (Outer) CPVC pipes SDR 13.5 & Plain CPVC SDR 13.5 fittings fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 79 here-in-above, but for 25mm dia GI tubing, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 79 here-in-above, but for 32mm dia GI tubing, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Rotational Moulded Polyethylene Water Storage Tank 500 Litre capacity (Cylindrical Vertical with Closed Top), 3 layered, hoisted and fixed in position, all as specified in MES Schedule Part-I with and including providing 20 mm dia float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 82 here-in-above, but for 1000 Litre tank, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20 mm dia float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 84 here-in-above, but for 25 mm dia float valves (Minimum weight 455gm), complete all as specified and as directed by Engineer-in-charge.

S&F of 20 mm bore (dia), gun metal gate valves with iron wheel head, screwed both ends for iron pipe, ISI Marked, as per IS: 778 and including taking out old unserviceable gate valves complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 86 here-in-above, but for 25 mm dia gun metal gate valves, complete all as specified and as directed by Engineer-in-charge.

M&L for cleaning of GI/CPVC water pipe line of 15-25 mm dia through specialized in researching and manufacturing the multi-functional water pipe cleaner which utilizes advance TRIC technology, multi-pulse and Citric acid aleaning technology, without replacing pipes, but removing all clogges in water pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of PVC connection pipe 15mm dia with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated swan neck Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Bib tap with wall flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Bib taps 2-in-1 (2-way), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated towel ring, square type, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated towel rack/ shelf, 225mm wide, 600mm long between flanges with lower hanger, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Grating doom of 100 mm dia with waste hole of PTMT (Minimum weight 25gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 32 mm bore (dia), Waste coupling of PTMT (half or full threaded) (Minimum weight-45gms) complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 40 mm bore (dia), Waste coupling of PTMT (half or full threaded) (Minimum weight-45gms) complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.0 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of PVC Mirror cabinet with shelf of size 540 x 340 x 130mm with and including CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in repair PVC water tank cover suitable for any capacity PVC water tank 6mm dia MS bar hinging device and S type locking arrangements, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of corner Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of plate rack/ kitchen rack made of stainless steel 1mm thick overall size 900mm x 600mm x 250mm, fixed to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

formation inside the tank by using TERBAC G5/NB-10/Inchlor-5( lab tested chemical) including fixing sticker mentioning "TANK CLEANED ON' with date, month and year, complete all as specified and as directed by Engineer-in-charge. The cleaning process would follow following stages as under: (a) To drain out the water by using exit valve or high capacity dewatering system (b) Cleaning all the algae formation inside the tank by using TERBAC G5/NB-10/Inchlor-5 chemical. (c) Scrubbing the walls with mechanised scrubber & fresh water cleaning by high speed jet pump. (d) 1st stage of bacteria screening by degermification by using TERBAC G5 halogen compound. (e) Cleaning the floor of the water tank by industrial vacuum cleaner. (f) 2nd stage of bacteria screening & sterilizing method by using UV ray within the tank & killing all suspended bacteria. (g) 3rd stage of bacteria screening by sterilizing the floor of water tank by using strong oxidizing agent TERBAC-G65/NB-60/Inoxi-60. Note: The quoted rate to include for removal of mud, grits and deposits etc properly from site of work and on completion of wk, sterilisation certificate to be submitted to Engineer in Charge. NOTE: (i)Cleaning needs to be done mechanically by authorized dealer/agent as approved by GE. (ii) Chemical shall be approved by GE

All as per Item No. 109 here-in-above, but for tank capacity exceeding 1000 Litre, complete all as specified and as directed by Engineer-in-charge.

M/S Bhaskar Construction

M/S S.S. Construction

M/s SHARMA BUILDERS & ENGINEERS

MS Gautam Construction and CO

MUKUL CHOUDHURY

Shiva Builders

M/S NARAYAN ENTERPRISE

M/S Rajkamal Enterprise