Development of Disabled Park in Swami Vivekanand Park, Ward No.12 M. C. Karnal. (Only for L/c societies )

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including trengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Providing and laying 15mm thick synthetic jogging track EPDM (9mm SBR Crumb Rubber as track bottom Cushion Layer 6mm EPDM Colour Granules top layer) of approved make COLORSPACEF/COLORPLAY/BSG/NOVAL with test reports of certified NABL lab, origin Of EPDM USA and EUROPE and equivalent. EPDM Granules shall have following minimum properties 00 Polymer content )22%, (u) Hardness of 55-65 Shore A [per ASTM D2240): (ii) Tensile Strength of )5 MPa (per ASTM D412): (iv) Elongation )500% (as per ASTM D412): (v) Density of 1.6 kg/cum (per ASTM D792). (vi) High UV rating of 3-5 on grayscale, (vi) VOC less than 3.0.0ww/1 [viii] Combustibility less than40 mm /m: (ix) Anti-Microbial and Anti-Fungal Tested material, and shall be laid in three layers.[1] First step shall be the application of single component Polyurethane based primer coating Layer, PU binder shall have a specific gravity of 1.05 the appearance of clear pale yellow and viscosity of 350-2900 cps and shall be from the original manufacturer from the list of approved makes. 2. The second layer shall be an impact attenuating cushion layer of 9mm thick black crumb rubber/SBR adhered with a polyurethane binder and PU binder shall have a specific gravity of 1.05: the appearance of clear pale yellow and viscosity of 350- 2900 cps and shall be from the original manufacturer from the list of approved makes of to form a resilient porous layer. Crumb rubber /SBR shall be mixed with a minimum of 14% -16% of single-component PU base binder so as to ensure that PU binder provides 100% coating of the SBR/crumb rubber particles. The third step shall be laying a 6mm 18% binder of single EPDM GRANULES top layer with at minimumcomponent polyurethane and shall provide 100% coating of the EPDM granules particles Design on the base top layer by a specialized team of installers according to the specification of approved material and shade. The detailed technical specifications of EPDM flooring testing. material properties, application procedure, etc. are attached herewith for compliance. The documentary evidence has to be produced. for the procurement of material for manufacturer`s test certificate. An undertaking is to be furnished by the agency that surface system is tested EN 1177 For shock absorption report of SPORTS LAB approved by IAAF WORLD Athletics` company has not been World blacklisted by IAAF/Sports Authority of India/ Athletics `IAAF the means earlier `international Association of Athletics Federations or World Athletics now. The work shall be carried out by the manufacturer`s approved applicator and the prospective bidder should produce a letter from the approved strictly to manufacturer prior to submission of bid and satisfaction of the technical specifications and the engineer-in- charge. (Guarantee Period Five years)

SIT `N` SNICKER SWING - Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6–2.0 mm thick) Manufacturing: CNC laser- cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform. Swing Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.

CHEERFUL CHURN Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6–2.0 mm thick) Manufacturing: CNC laser- cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform. mgr Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.

WHEELCHAIR Providing and supplying standard manual wheelchair made of high-quality powder- coated/mild steel tubular frame with durable, corrosion-resistant finish. The wheelchair shall be foldable type for easy storage and portability. Technical Specifications: Frame: Mild Steel/Aluminum, powder-coated finish Seat Width: Approx. 18 inches (450 mm), made of durable, washable canvas or PVC upholstery Backrest: Fixed/Foldable with reinforced support Wheels: Rear wheels: 24` solid rubber with hand rims for self-propelling Front wheels: 8` PU/solid rubber caster wheels Brakes: Manual parking brakes on both rear wheels Footrests: Foldable/Detachable, height-adjustable with heel support strap Armrests: Fixed or flip-up cushioned armrests Load Capacity: Minimum 100 kg Foldable Design: For convenient storage and transportation Warranty: Minimum 1 year against manufacturing defect

Sea-Saw Main Structure Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Handle and Leg rest Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 25 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Seat : designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for Spring: Heavy-duty coil spring, High-carbon steel or alloy spring steel, 18 mm – 20 mm wire thickness, Coil height: Approx. 300

FISHY FUNNY SEE SAW Main Structure Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Handle and Leg rest Material: Galvanised Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 25 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating(min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Seat : designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for Spring: Heavy-duty coil spring, High-carbon steel or alloy spring steel, 18 mm – 20 mm wire thickness, Coil height: Approx. 300 mm.

DUET Main Structure Material: Stainless Steel 304 Grade, 1.5–2.5 mm thick pipe or tube Dimensions: Minimum 60–32 mm outer diameter (OD), 1.5–2.5 mm thickness Cap HDPE Heigh dencity polyetheline 20mm thickness. Fasteners Material: Stainless steel fasteners are specified to BS EN ISO 3506. Part 1 covers bolts, screws and studs. Safety Compliance Standards: EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended.

XOXO PANEL Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 114 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Play panel LLDPE (Linear Low-Density Polyethylene), roto-moulded Thickness: 6–8 mm wall thickness. Finish Seamless, anti-static, smooth surface UV Resistance. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts.

GONDOLA SWING Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60 – 80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6–2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform. Swing Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut. Pins: are made up of M.S bright bar. Bearing bushes: 089mm OD seamless pipe. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. 130000Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60–80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilized Safety Compliance Standards: EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended.

ARM REVOLVE ASSIST Main Frame: 0114 *3 mm thick M.S pipe and subordinate tube is of 088*3.0 large thickness M.S pipe. Handle: is made of 088 *3 mm thick Pipe and 025 mm round M.S bright bar in bending design. All remaining frame is made by 088 *3mm thick MS pipe. Weight plates: Rubberized moulding round weight plates are used. Weight Plates Holder with spring lock and spare weights holder: is made by hard chrome plated mild stee!048 D!A pipe open front covered with half round cap and holder end is covered with heavy quality rubber ring of OD-68 mm and ID-48 mm with 10mm wall thickness for free weight noiseless operations. Bearing: Lubricated high grade6305 `2RS`steel ball bearing. Base plate: is OD166, ID 116, and 6 mm thick. Pins: are made up of M.S bright bar. Bearing bushes: 075mm OD seamless pipe. Weight plate mounting pipe is of 048 mm MS pipe. Seat Frame: made up of hard chrome plated mild steel 48 DIA round pipe. Hardware All hardware`s uses button heads bolts and nuts made up of high tensile steel. Hand grips: Hand grips is used on handles wherever necessary made up of high-quality rubber and handle ends are covered with aluminum/pp/nylon caps with grub screw for long endurance. Closing caps: are of PP/NYLON/HDPE materia!. Laser cutting: profiles of 6mm and 4mm thick M.S sheet are used for connecting subordinates with each other. Rubber: Safety base pads: Anti-skid safety base pads made up superior rubber to prevent slippery and damage to floor. Heavy duty 20mm thick rubber pads are placed for resting handles for noise less operations. 36000Powders Coating: All components are chemically treated to seal exterior and interior surfaces against corrosion. The components are electro statically powder coated at minimum 80-100-micron thickness to make it resistant to scratch, corrosion and humidity in dual color combination. Safety Instructions and Exercise chart on machine - start and finish position chart stick on 5mm

MERRY-GO-ADAPT Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor- grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6–2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform. mgr Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut. Pins: are made up of M.S bright bar. Bearing bushes: 089mm OD seamless pipe. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60–80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilized Safety Compliance Standards: EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended.

PLAYFUL PANEL Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 114 mm outer diameter (OD), 2.0–3.0 mm thickness Surface Finish Zinc primer plus outdoor- grade polyester powder coating (min. 60–80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Play panel designed for outdoor playgrounds. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut for engaging graphics through play. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic. Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60–80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades, UV-stabilized Safety Compliance Standards: EN 1176 (Europe)ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention: No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M20 grouting Installation: Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended.

Providing and fixing Octagonal FRP Gazebo made of fiber-reinforced polymer (FRP) with MS/GI structural support frame, includingroofing,columns, flooring, seating, painting, hardware and complete installation at site. The gazebo shall be durable, weather-resistant, UV-protected,corrosion-free and suitable for outdoor public spaces.

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

[10.42]Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. [Through Rate]

[11.6.1]15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) [Through Rate]

[11.60]Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. [Through Rate]

[11.67.1]Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 1. Water thinnable cement primer [Through Rate]

[11.71.1]Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new work [Through Rate]

[13.29.2]Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works [Through Rate]

[26.122]Providing and displaying of Specimen Croton Petra Bangalore variety plant, having ht. 60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy foliage approximately 60-65 leaves in 30 cm size of Earthen pot/Plastic pot and as per direction of the officer-in-charge. [Through Rate]

[26.215]Providing and Displaying Marigold(Tagetes) inca hybrid different colour having 30 cm and above ht., with 6 to 8 flowers in bloom and blooming condition, well developed pot should be fully covered with fresh and healthy, foliage and flowers in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. [Through Rate]

[26.226]Providing and Displaying Petunia hybrid well developed with fresh and healthy foliage in full bloom 15-20 plants in 60x35 cm Earthen Tray and as per direction of the officer-in charge. [Through Rate]

[26.328]Providing and stacking of Iresine herbstii, of height 20-30 cm. full of branches well developed in 10 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge. [Through Rate]

[34.8.2]Informatory sign board 800x600 rectangular as per IRC 67- 2012 with retro reflective Sheeting as per ASTM D 4956 09 and as per IRC 67 2012 fixed over 4 mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.75m for vertical post complete as per clause 801 of MORTandH specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting and a certified copy of test reports from an independent test laboratory including three year outdoor weathering test report for sheeting tested in India condition conforming to clause 6.7 of IRC 67-2012 2. Using high intensity Microprisomatic grade retro reflective Sheeting Class B as per IRC 67 2012 [Through Rate]

[4.12.1]Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. 1. All kinds of soil [Through Rate]

[4.14.1]Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil. [Through Rate]

[4.33]Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. [Through Rate]

[6.1.1]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1. 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) [Through Rate]

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) [Through Rate]

[7.21.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: 1. Cement mortar 1:4 (1 cement : 4 coarse sand) [Through Rate]

[7.22.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand) [Through Rate]

[8.9.3.2]Stone work (machine cut edges) for wall lining etc. (veneer work) up to 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 3.2. Gang saw cut stone. 30mm thick Red sand stone [Through Rate]