REPAIRS TO JOINERY, FLOORING, ROOFING, CEILING PLUMBING WORK AND PERIODICAL SERVICES TO CERTAIN BLDGS AND REPAIRS TO DRAINS, COMPOUND WALLS, FENCING AND CLEANING/ REPAIRS TO SEWAGE LINES, MANHOLES, SOAKAGE WELLS AND SEPTIC TANKS AT NLP MIL STN UNDER

Amount

DEMOLITION & DISMANTLING

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Cement Concrete (Un-reinforced) in any Position not otherwise specifically Provided for and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Reinforced Cement Concrete in any Position not otherwise specifically Provided for and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Dismantling Posts or Struts (Steel or RCC) any Section, embedded in Natural Ground including Taking out embedded Portion of Posts or Struts and Making Good Disturbed Ground, complete all as specified and as directed. NOTE : Excavating in Post Hole will be Measured and Paid for separately under appropriate Items.

Dismantling Posts or Struts (Steel or RCC) any Section, embedded in Cement Concrete including Taking out embedded Portion of Posts or Struts and Making Good Disturbed Ground, complete all as specified and as directed. NOTE : Excavating in Post Hole will be Measured and Paid for separately under appropriate Items.

Taking down Damaged/ Unserviceable Jallies of any description, complete all as specified and as directed.

Demolition Brick Work, Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. including Serviceable Bricks keep in Safe custody for Re-use at Site, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Dismantling Timber Boarding of any description, fixed in any Position with Nails, etc., complete all as specified and as directed.

Taking down Chowkat or Frame (without Taking Off Shutter from the Frame) of any description, not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, not exc. 1.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Hacking out Old Broken Glass (any thickness, Size, quality or description) from Wooden or Metal Frame or Stone, Concrete or Brick surrounds including Hacking out old Putty or Removing Beads, etc., Punching or Drilling out Old Glazing Pins/ Spring Clips, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work of any description including Serviceable Wrought Iron or Mild Steel keep in Safe Custody for Re-use at Site (if any ordered), complete all as specified and as directed.

Dismantling Fencing Wire Mesh of any description including Serviceable Chain Link Fencing keep in Safe Custody for Re-use at Site (if any ordered), complete all as specified and as directed.

Dismantling Galvanised Steel Barbed Wire of any description including Serviceable Barbed Wire keep in Safe Custody for Re-use at Site (if any ordered), complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Plain or Corrugated Steel Sheeting and Stacking Properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers of any descriptions but except Wall and Ceiling Boards, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down PVC (SWR) Soil, Waste and Ventilating Pipe 75/110mm bore (dia) with Fittings of any description from any Situations, complete all as specified and as directed.

Demolition & Breaking up Drain/ Seware Pipe 100/110mm dia (Salt Glazed Ware, PVC (SWR), AC or Reinforced Concrete) including PCC Haunching (except Bed), set in Cement Mortar, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid separately under appropriate Items.

Demolition & Breaking up Drain/ Seware Pipe 150/160mm dia (Salt Glazed Ware, PVC (SWR), AC or Reinforced Concrete) including PCC Haunching (except Bed), set in Cement Mortar, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid separately under appropriate Items.

BLDG REPAIRS/ MAINT WORKS

M&L Machine Made & Pressed Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for Taking out/ Inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled Portion with Cement Concrete 1:3:6 (20mm graded stone aggregate) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Boarding 50mm thick (100x50mm) in Frame Work to Ceiling, etc., Planned on One Side, fixed in any Position with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Cleanswan, Square, Rect-angular or Triangular in Section, exc. 13.00 Sq Cm but not exc. 25.00 Sq Cm (50x50mm as STUDS), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Cleanswan, Square, Rect-angular or Triangular in Section, exc. 6.00 Sq Cm but not exc 13.00 Sq Cm (25x25mm as FORKING PIECE), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectan-gular or Triangular in Section, exc. 3.00 Sq Cm but not exc. 6.00 Sq Cm (40x12mm as COVER FILLET), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

S&F Flush Shutter 35mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open Rebated and Prepared to Receive Glass, Gauze, etc., Divided into Squares, with Plain, Chamfered or Rounded, Mitred and Rebated Sash Bars any Numbers fitted with Cut and Mitred Beads for Securing Glass, etc.; Sizes of Members of Shutters as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed.

S&F Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain Colour PVC Sheet Reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain Color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/ sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement and fixing in the Frame as per Site as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 125mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy anodized, Sliding Door Bolt 300mm Long with Hasp Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Section and fixing Bolts and Sliding Bolts of Extruded Section, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm (as approved), complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 125mm, Cast type, complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 150mm, Cast type, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and Fixed-in-repairs, complete all as specified and as directed.

S&F Door Closer Aluminium (Die-cast) Body, Hydraulically Regulated, Designation No. 2, Universal type, suitable for Door Shutters of 701mm to 850mm in Width and of Weight between 36.00 to 60.00 Kilogram and Fixed-in-repairs, complete all as specified and as directed.

S&F Mild Steel Cupboard Knobs 40mm dia, Bright Finished, fixing with Nut, Screw and Washer and Fixed-in-repairs, complete all as specified and as directed.

M&L Stainless Steel Curtain Rail/ Rod having 24mm Outer dia and 1.0mm Wall thickness including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed. NOTE :- (a) Stainless Steel Decorative Finials and Stainless Steel Brackets will be provided for Each Length of Curtain Rail/ Rod and Cost of the same will deemed to be included in the Quoted Unit Rate. (b) Only Length of Curtain Rail/ Rod will be Measured for Payment.

M&L Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed. NOTE : Cost of Second Class Hardwood Beading, etc. will be Measured and Paid under Item No. 2.010 here-in-before.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality, in Square not exc. 0.50 Sqm in Each Pane and Glazing with Oil Putty/ Beading, complete all as specified and as directed. NOTE : Cost of Second Class Hardwood Beading, etc. will be Measured and Paid under Item No. 2.010 here-in-before.

M&L Mild Steel Bands, Straps, Supports or Stays for Rain Water, Ventilating Pipes including Bolts (if required), Heavy Hooks (Stay) for Large Gates; Hook and Pintle Hinges, Large Hasps and Staples; Chains; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x4.0mm); Wall Ties; Hooks for Hanging Fans; Plain Angle Cleats for securing Purlins to Wood Trusses or Rafters; Knee Piece inserts; 2-way and 3-way Straps, Plate Washers and Similar Small Articles, conform to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Mild Steel Tublar Trusses including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Re-fixing only Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Sheet obtained from Item No. 1.019 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 275 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Re-fixing only Plain Mild Steel Sheeting 0.63mm thick (Serviceable Sheet obtained from Item No. 1.019 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

Re-fixing only Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet (Serviceable Galvalume Corrugated Steel Sheet obtained from Item No. 1.019 here-in-before) in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Exposed Suspended False Ceiling System with Powder Coated Anodised Aluminium Sections Snap Grid/ Frame Work of Size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for Adjusting Level, fixed to Roof Slabs, Trusses by means of Ceilling Cleats made out of GI Flat of Size 40x3.0mm, 60mm Long and Expansion Hold Fasteners having 40mm Long & 12.5mm dia, complete all as specified and as directed.

M&L GI Frame Work for Seamless Ceiling comprising of GI Perimeter Channnel 0.55mm thick with 2 Unequal Flanges of 20mm and 30mm and Web of 27mm fixed to surrounding Walls using Nylon Sleeves and Screws at 450mm Centre to Centre/ Inter-mediate Channel 0.9mm thick having 2 Equal Flanges of 15mm Each and Web of 45mm suspended from Soffit at approx 900mm Centre to Centre with GI Cleat and Steel Expansion Fasteners with and including Ceiling Section (not exc 1200mm length) of 0.55mm thickness having kurled Web of 50mm and Flange of 26mm Each with Lips of 10.5mm fixed to the Intermediate Channel with Connecting Clips across the Interme-diate Channel at 457mm Centre to Centre, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick in Ceiling, fixed to Timber Frame Work with Screws, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick in Ceiling, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Plywood Board 4.0mm thick (3 Ply), Grade BWR, Type BB, fixing with Mild Steel Screws to Timber Frame Work and Fixed-in-repairs, complete all as specified and as directed.

S&F Plywood Board 6.0mm thick (5 Ply), Grade BWR, Type BB, fixing with Mild Steel Screws to Timber Frame Work and Fixed-in-repairs, complete all as specified and as directed.

S&F Plywood Board 9.0mm thick (5 Ply), Grade BWR, Type BB, fixing with Mild Steel Screws to Timber Frame Work and Fixed-in-repairs, complete all as specified and as directed.

S&F Plywood Board 12mm thick (9 Ply), Grade BWR, Type BB, fixing with Mild Steel Screws to Timber Frame Work and Fixed-in-repairs, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.06 Sqm but not exc. 0.11 Sqm (1st quality) in Floors, Set and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Set and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Vitirified Ceramic Tiles 10mm thick (Square/Rectangular) in Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc., Set and Jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Vitirified Ceramic Tiles 10mm thick (Square/Rectangular) in Dark shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc., Set and Jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 300x200x7.0mm thick in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 Layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Surfaces of New Non-Asbestos Fibre Cement Building Boards in Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whiting (Priming Coat), complete all as specified and as directed.

M&L Complete Removal of Existing Surface Treatment from Plastered Surfaces of Walls including Washing, Rubbing down and Stopping of Surfaces and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whiting Priming, complete all as specified and as directed.

M&L Complete Removal of Existing Surface Treatment from Distempered Treated Walls and Applying Wall Care Putty 3.0mm thick in Two Coats (1.5mm thick in Each Coat) on Plastered Surfaces of Walls including Cutting/ Rubbing down to obtain an Even and Smooth Surface and Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing Previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and Treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing Previously Untreated Surfaces of any description and girth not otherwise described and Treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Steel Tubing 15mm bore (dia) and Connections, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Steel Tubing 20mm bore (dia) and Connections, complete all as specified and as directed.

S&F CPVC Pipes 20mm Outer Dia, SDR 13.5 & Plain CPVC SDR 11 Fittings on Walls/ Ceiling or laying in Floors including Taking up or down Steel Tubing 15mm bore (dia) and Connections, complete all as specified and as directed.

S&F CPVC Pipes 25mm Outer Dia, SDR 13.5 & Plain CPVC SDR 11 Fittings on Walls/ Ceiling or laying in Floors including Taking up or down Steel Tubing 20mm bore (dia) and Connections, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Long Body with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Cock/Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Angle Stop Cock 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 15mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylin-drical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, Hoisted and Fixed in Position all as specified in MES Schedule and Providing Water Connections including Lowering down Unserviceable Water Storage Tank of any description after disconnecting Water Connections, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylin-drical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, Hoisted and Fixed in Position all as specified in MES Schedule and Providing Water Connections including Lowering down Unserviceable Water Storage Tank of any description after disconnecting Water Connections, complete all as specified and as directed.

S&F Plastic Top Cover Assembly suitable for Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top and Fixed-in-repairs, complete all as specified and as directed.

S&F Plastic Top Cover Assembly suitable for Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Ball Valve 15mm bore (dia), having weight not less than 142 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Disconnecting all the Pipe Connections, Cleaning & Removal of all Scales, Dirts, etc. from the Tank of capacity exc. 250 Litre and not exc. 500 Litre and Mouths of Circulating Pipes, etc. Cleaning the Tank by scrubbing the deposits with Wire Brush after draining out Water from the Tank, Re-hoisting the Cleaned Tank in Original Position and Re-fixing/Re-connecting Inlet and Outlet Pipes and Writing Letters "CLEANED ON : DD.MM.YYYY" (i.e. Date of Cleaning of Tank) not less than 25mm in Height, complete all as specified and as directed.

M&L Disconnecting all the Pipe Connections, Cleaning & Removal of all Scales, Dirts, etc. from the Tank of capacity exc. 500 Litre and not exc. 1000 Litre and Mouths of Circulating Pipes, etc. Cleaning the Tank by scrubbing the deposits with Wire Brush after draining out Water from the Tank, Re-hoisting the Cleaned Tank in Original Position and Re-fixing/Re-connecting Inlet and Outlet Pipes and Writing Letters "CLEANED ON : DD.MM.YYYY" (i.e. Date of Cleaning of Tank) not less than 25mm in Height, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, SWG ‘P’ or ‘S’ Trap, Providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding Provision of Lime Concrete Bedding and Making Good to Floor/ Distrubed surfaces and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with SWG ‘P’ or ‘S’ Trap, Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Devices and Fixed-in-repairs, complete all as specified and as directed.

S&F Hand Shower (Health Faucet) with Wall Hook, Brass Chromium Plated having 1.20 Metre long with PVC Hose Pipe and Fixed-in-repairs, complete all as specified and as directed. MAKE : JAQUAR ALD-CHR-593 or equivalent Model in Make : GEM/ MARC (as approved by GE)

S&F Jet Spray with Connection Pipe 15mm bore (dia), Brass Chromium Plated (as approved) and suitable for Wash Down Water Closet Pan (Pedestal Pattern) and Fixed-in-repairs, complete all as specified and as directed.

S&F Toitet Paper Holder of Size 150mm (as approved), Brass Chromoum Plated with Rod to hold Paper Roll and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type, ISI Marked (IS:7231) with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted including PVC Flush Pipe 32mm dia with PVC Long Bend, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin of Size 550x400mm, Flat Back including Brass Chromium plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of Low or High density, a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but excluding Taps, Chain, Plug & Porocelain Stopper and Fixed-in-repairs, complete all as specified and as directed.

S&F Kitchen Sink with Drainage Board made of Stainless Steel l.0mm thick of Overall size 915x460mm having Bowl Size 410x330x160mm with Plugs, Washers and Stainless Steel Waste Fittings, etc. including bedding in Cement Mortar to dwarf Wall or including fixing Cantilever Brackets and connecting Union to Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Waste Coupling of size 32mm having Minimum Weight 45 Gram (Half or Full threaded) and fixed-in-repairs, complete all as specified and as directed.

S&F Basin Mixer 15mm bore (dia), Brass Chromium Plated for mixing Hot & Cold Water, screwed down for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Urinal, Half Stall type (excluding Flushing Cistern, Flush Pipe and Waste Pipe) including Providing and Fixing Plugs, Bedding Urinals against Wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, fixing Urinal Spreder of Brass Chromium plated, Flush Pipe, Grating and Union for Discharge Pipe (but Exclusive of fixing Supply Pipe to Flushing Cistern, Trap and Waste Pipe) and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Waste Pipes 32mm/40mm bore (dia) of suitable Length for Wash Hand Basin, Sinks, Urinals, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts and Fixed-in-repairs, complete all as specified and as directed.

S&F Chromium Plated Shower Rose with Shower Arm 125mm, Swival Joint including fixing to Steel Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Wall (Bath) Mixer 15mm bore (dia), Brass Chromium Plated, suitable for mixing Hot & Cold Water, screwed down for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Soap Dish not less than 150mm in size (as approved) Chromium Plated and fixing to Walls with Screws and Fixed-in-repairs, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair) and Fixed-in-repairs, complete all as specified and as directed.

S&F Glass Shelf Assembly (as approved) consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Grating Doom 100mm dia with Waste Holes, Chromium Plated (as approved) and Fixed-in-repairs, complete all as specified and as directed.

M&L Cast Iron Floor Trap with Grating having Diameter of Outlet in 75mm including Jointing to Waste Pipe fixing in Cement Concrete type 1:2:4 (20mm graded stone aggregate) and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Floor Trap 75mm bore (dia) with Chromium Plated Grating, Plain including Jointing to Waste Pipe with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Gully Trap 125/110mm bore (dia), Setting and Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

Attending Day-to-Day Complaint to Water Leakage from Taps, WCs, Flushing Cistern, Urinals, Wash Hand Basins, Bottle Traps, etc., any obstruction to Water Supply requiring Plumbing Work and Carry out Minor Repairs such like Replacement of Washers, Check Nuts, Tightening of Fittings, Adjustment of Float Valves, Syphon Fittings of Flushing Cistern, Cleaning of Bottle Traps, etc. in the Area of NLP MIL STN, complete all as specified and as directed. NOTE :- (a) The Complaints shall be Attended and Defects shall be rectified within 08 Hours i.e. from 0900 Hours to 1700 Hours excluding Sunday, Gazetted Holiday, commencing from Date & Time of notifying the Complaint Slip, failing which a Penalty @ Rs. 50.00 Per Complaint Per Day (08 Hours) shall be levied on/imposed on the Contractor and Recovery shall be made from his Dues. Any Materials which are required to be replaced shall be supplied by the Department, but Cost of the Labours/ Tradesmen Elements as required shall deemed to be included under Quoted Unit Rate of this Item. (b) In addition of above, Contractor shall arrange suitable T&P such as Die Set (½"-1"), Washers of all Sizes, Safeda, Thread (Soot), M-seal, Screws, Nails and the like including necessary Scaffolding and also Providing all Safety Measures to make it Smooth Functional and Leak Proof as directed. The above aspect shall be deemed to be included in the Quoted Unit Rate of this Item. (c) Contractor or His Authorised Represntitive will Report Daily at Complaint Cell for collection of Complaint Slip(s) from the concerned JE-in-Charge. The Complaint Slip(s) shall be deposited to Complaint Cell after obtaining Signature from the Users. In case after Checking and Attending the Defects, if it is not possible to Rectify the Defects within 08 Hours, the facts shall be brought to the Notice of JE-in-Charge/ Engineer-in-Charge by the Contractor or His Authorised Represntitive immediately. If the JE-in-Charge/ Engineer-in-Charge is satisfied with Contractor's view, no Rrecovery will be made on this Account.

Attending Day-to-Day Complaint of Carpentary Work (Wooden/ Steel/ Aluminium) such as Mild Steel/ Stainless Steel/ Aluminium Mongery, Palmet Box, Door Springs, Rolling Shutters, Venetion Blinds, etc., requiring Carpentry Work and Carrying out Minor Repairs such as Tighting of Screws/ Nails, Easening of Joinery, etc. in the Area of Flushing Cistern, Cleaning of Bottle Traps, etc. in the Area of NLP MIL STN, complete all as specified and as directed. NOTE :- (a) The Complaints shall be Attended and Defects shall be rectified within 08 Hours i.e. from 0900 Hours to 1700 Hours excluding Sunday, Gazetted Holiday, commencing from Date and Time of notifying the Complaint Slip, failing which a Penalty @ Rs. 50.00 Per Complaint Per Day (08 Hours) shall be levied on/imposed on the Contractor and Recovery shall be made from his Dues. Any Materials which are required to be replaced shall be supplied by the Department, but Cost of the Labours/ Tradesmen Elements as required shall deemed to be included under Quoted Unit Rate of this Item. (b) In addition of above, Contractor shall arrange suitable T&P and Minor Items such as Screws, Nails, Plugs, Grease, Putty and the like including necessary Scaffolding and also Providing all Safety Measures to make it Smooth Functional as directed. The above aspect shall be deemed to be included in the Quoted Unit Rate of this Item. (c) Contractor or His Authorised Represntitive will Report Daily at Complaint Cell for collection of Complaint Slip(s) from the concerned JE-in-Charge. The Complaint Slip(s) shall be deposited to Complaint Cell after obtaining Signature from the Users. In case after Checking and Attending the Defects, if it is not possible to Rectify the Defects within 08 Hours, the facts shall be brought to the Notice of JE-in-Charge/ Engineer-in-Charge by the Contractor or His Authorised Represntitive immediately. If the JE-in-Charge/ Engineer-in-Charge is satisfied with Contractor's view, no Rrecovery will be made on this Account.

Attending Day-to-Day Complaint of Blacksmith Work to Welding Work in Repais to Steel Windows/ Doors, Handles, Door Springs, Iron Frame of Doors, Rolling Shutter and Other Iron Misc Works, Repair by Welding Run or Spot welding complete as per Site requirement in the Area of NLP MIL STN, complete all as specified and as directed. NOTE :- (a) The Complaints shall be Attended and Defects shall be rectified within 08 Hours i.e. from 0900 Hours to 1700 Hours excluding Sunday, Gazetted Holiday, Commencing from Date and Time of notifying the Complaint Slip, failing which a Penalty @ Rs. 50.00 Per Complaint Per Day (08 Hours) shall be levied on/imposed on the Contractor and Recovery shall be made from his Dues. Any Materials which are required to be replaced shall be supplied by the Department, but Cost of the Labours/ Tradesmen Elements as required shall deemed to be included under Quoted Unit Rate of this Item. (b) In addition of above, Contractor shall arrange suitable T&P such as Hacksaw Bleades, Welding Machine, Hand Gloves, Welding Glass, Welding Rod, etc. and any other Tools required including necessary Scaffolding and also Providing all Safety Measures to make it Smooth Functional as directed. The above aspect shall be deemed to be included in the Quoted Unit Rate of this Item. (c) Contractor or His Authorised Represntitive will Report Daily at Complaint Cell for collection of Complaint Slip(s) from the concerned JE-in-Charge. The Complaint Slip(s) shall be deposited to Complaint Cell after obtaining Signature from the Users. In case after Checking and Attending the Defects, if it is not possible to Rectify the Defects within 08 Hours, the facts shall be brought to the Notice of JE-in-Charge/ Engineer-in-Charge by the Contractor or His Authorised Represntitive immediately. If the JE-in-Charge/ Engineer-in-Charge is satisfied with Contractor's view, no Rrecovery will be made on this Account.

PERIODICAL SERVICES TO CERTAIN BLDGS

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Ceiling and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing Old Distempered and Painted Surfaces of Walls by Washing, Rubbing down and Stopping of Surfaces and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Old Distempered and Painted Surfaces of Ceiling by Washing, Rubbing down and Stopping of Surfaces and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Cement Base Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description (i.e. Other than Roofing, Wall Cladding, etc.), over 10 Cm Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description (i.e. on Roofing, Wall Cladding, etc.), over 10 Cm Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description (i.e. on Roofing, Wall Cladding, etc.), over 10 Cm Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Asbestos Cement Building Boards Panel Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Painted/ Treated Brick, Stone, Concrete, Asbestos Cement or Plaster Surfaces, Area not exc. 0.25 Sqm and applying One Coat of Synthetic Enamel Paint (Black/ Red or as approved Tint) as Base Surface Area for Writing Letters, etc. , complete all as specified and as directed.

M&L Stencil Writing Letters or Figures (Block. Roman, Italic or Indian) of Height exc. 150mm and not exc. 200mm with White Synthetic Enamel Paint over Black/ Red Base Surfaces, complete all as specified and as directed.

M&L Stencil Writing Stops, Commas, Short Lines, Dashes, Hyphens, Brackets, etc. with White Synthetic Enamel Paint over Black/ Red Base Surfaces, complete all as specified and as directed.

EARTH WORKS

Excavating in Trenches, not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth; for Foundation, etc. or for Shafts, Wells, Cesspits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in approved Soft/Loose Soil including Spreading, Leveling, Watering and Well Ramming in Layers not exc. 25 Cm thick, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and Depositing where directed at a Level not exc. 1.50 Metre above the Starting Point including Spreading over Ground, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, Each not exc. 0.50 CUM, getting out and Removing Surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, Each not exc. 0.50 CUM, getting out, Returning, Filling in and Ramming Earth or Broken Rubble mixed with Earth around in layers not exc. 25 Cm, Watering and Removing Surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

REPAIRS/MAINT TO DRAINS, COMPOUND WALLS, FENCING & SEWAGE

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Surface Channels and Drains, etc. including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Extra for Forming Fair finished Drain or Channel not exc. 30 Cm Inner Girth in Cement Concrete, Using Extra Cement including Forms, Moulds, Stopped Ends, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregates) in Lintels upto 1.50 Metre Clear Span, Cills, Steps; Seismic and Other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings upto 600mm in Height, Copings, Kneelers, Apex Stones, Bed Plates, Water Troughs and the Like including Weathering, Slightly Rounded or Chamfered Angles and Throating, Finishing all Exposed Faces of Concrete including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. for embedding /fixing Fencing Posts or Struts including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including Use and Waste of Formwork as required/ ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and Setting in Cement Morter 1:6, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Fencing Posts, Struts, etc., average Sectional Area not exc. 100 Sq Cm, with or without Chamfered Angles and flat, splayed, rounded or mitred Tops and fixed, etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Fencing Posts, Struts, etc., average Sectional Area exc. 100 Sq Cm but not exc. 250 Sq Cm, with or without Chamfered Angles and flat, splayed, rounded or mitred Tops and fixed, etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (12.5mm graded stone aggregate) in Louvres and Jallies, 35mm thick (measured solid) with all mouldings including Reinforcement with 4.0mm dia Mild Steel Wire and setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Cost of Mild Steel Wire as Reinforcement will deemed to be included in the Quoted Unit Rate.

M&L Machine Made & Pressed Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick Work with Sub-class ‘B’ Bricks but except Bricks (Serviceable Bricks obtained from Item No. 1.007 here-in-before) including Removing Mortar from the Serviceable Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L TMT Bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia, cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Framed Work as in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., complete, drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for Hanging or Sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or Other Covering, Running Rails and Guides) and Hanging; also Fastening and fixing, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Works such as Posts and Struts in Fencing including cutting Tops to shape as directed, drilling holes, notching for Wire, etc.; including all necessary drilling, bolting or riveting, etc. and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x4.0mm (Fillet for securing Wire Mesh, etc.) cut to length including all necessary drilling, bolting or riveting, etc. and Similar Work, conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L Mild Steel Round Bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Screw Bolts (machine made) 11mm to 15mm diameter of Neck and length of Bolt exc. 5.0 Cm and not exc. 10 Cm with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal/Square Nut, complete all as specified and as directed.

Supply only Chain Link Fencing 75x75mm or 100x100mm mesh with 3.15/4.0mm dia Mild Steel Galvanised Wire, complete all as specified and as directed.

M&L for Fixing only New Chain Link Fencing including Line Wires, any mesh, size and type to any type of Standards, Rails, Straining Bolts, etc. including Provission of Mild Steel Binding Wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

S&F Galvanised 2 Strand, Steel Barbed Wire 2.24mm dia barbed with 2mm dia Barbs at 75mm spacings and straining and fixing to any type of Standard Rails straining Bolts, securing or tying at crossings with and provision of Galvanised Mild Steel Wire, Staples or Steel Pins, etc., complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

M&L Machine Pressed Pre-cast Concrete Coloured Interlocking Polished Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked in Floors, laid dry over Clean Dry Sand and grouted with Clean dry Sand, complete all as specified and as directed. NOTE : Clean Dry Sand will be Measured and Paid separately under appropriate Item.

M&L Sand Filling under Pre-cast Concrete Paver Blocks including Watering (if any ordered) and Consolidation, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:4 on Concrete Works, finished Plastered Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed.

M&L Preparing Newly Plastered or Concrete Surfaces of Walls and Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Concrete Surfaces of Jallies and Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Steel and Iron Surfaces of any description, over 10 Cm in Width or Girth, not otherwise described and applying Two Coats of Synthetic Enamel Paint (1st Grade/ Quality) over a Coat of Red Oxide Zinc Chrome Primer complete all as specified and as directed.

M&L Preparing New Steel and Iron Iron Surfaces of any description, not exc. 10 Cm in Width or Girth, not otherwise described and applying Two Coats of Synthetic Enamel Paint (1st Grade/ Quality) over a Coat of Red Oxide Zinc Chrome Primer complete all as specified and as directed.

M&L Preparing New Steel and Iron or Cement Concrete Surfaces of any description, over 10 Cm in Width or Girth, not otherwise described and applying Two Coats of Black Bituminous Paint (as approved), complete all as specified and as directed.

M&L UPVC Pipe (SCH-40) 75mm bore (dia), laid in/ fixing as Weep Holes with Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any Length with PVC/Rubber Ring Joints, with or without Ears, fixing to Walls, etc., complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Bends (any Radius), Diminishing Pieces or Tapers (Larger bore measured) Fittings, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Branch Pieces, Single (Equal or Unequal), Ordinary or Inverted (Spigot or Socket type) or with Parallel Branches Fittings with Access Door, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Junction, Single (Single T) Equal or Unequal with Access Door, etc. with Access Door, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia), Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any Length with PVC/Rubber Ring Joints, with or without Ears, fixing to Walls, etc., complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Bends (any Radius), Diminishing Pieces or Tapers (Larger bore measured) Fittings, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Branch Pieces, Single (Equal or Unequal), Ordinary or Inverted (Spigot or Socket type) or with Parallel Branches Fittings with Access Door, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Junction, Single (Single T) Equal or Unequal with Access Door, etc. with Access Door, Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any Length with PVC/Rubber Ring Joints, with or without Ears, laid in Trenches, etc., complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

S&F PVC (SWR) 160mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any Length with PVC/Rubber Ring Joints, with or without Ears, laid in Trenches, etc., complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 110mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and Tested; complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and Tested; complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cutting into Existing Manholes for Connecting New Drain Pipes of 160mm (Internal dia), Making Good to Pipe and Rendering, Cutting out Existing Benching for and Forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

CLEANING TO SEWAGE SYSTEMS

M&L Removing and/or Cleaning Blockage of Floor Trap, Nahani Trap, etc. of any description by any Means of Flushing with Water, complete all as specified and as directed. NOTE : The Item is Measurable/Operative upto THRICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department.

M&L Removing and/or Cleaning Blockage of Water Closet (WC) of any description of any description by any Means of Flushing with Water, complete all as specified and as directed. NOTE : The Item is Measurable/Operative upto THRICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department.

M&L Removing/Cleaning Blockage of Sewer Line 100/110mm bore (dia), Manually by Rodding from Manholes, Septic Tank, etc. and cleaning of Sewer Line by flushing with water, complete all as specified and as directed. NOTE : The Item is Measurable/Operative upto THRICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department.

M&L Removing/Cleaning Blockage of Sewer Line 150/160mm bore (dia), Manually by Rodding from Manholes, Septic Tank, etc. and cleaning of Sewer Line by flushing with water, complete all as specified and as directed. NOTE : The Item is Measurable/Operative upto THRICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department.

M&L Cleaning GULLY TRAP of Depth not exc. 0.50 METRE, by Opening Cover and Taking out accumulated Garbage, Silts, Sludge or any other Items, Re-fixing the Cover after cleaning of Gully Trap, Removing/ Carrying Garbage, Silts, Sludge or any other Items to a distance exc. 50 Metre but not exc. 100 Metre and burried into Earth Pit (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg Per Sqm at Top of deposited Garbage, Silts, Sludge or any other Items including Returning, Filling in, Dressing of Surplus Soils and Providing Ground to Slope, etc. (as required/ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative upto TWICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) Cost of Bleaching Powder, T&P, Labours, Excavation of Earth Pit, etc. as required for Cleaning will deemed to be included in the Quoted Unit Rate

M&L Cleaning MANHOLE of Depth not exc. 0.50 METRE, by Opening Cover and Taking out accumulated Silts, Sludge or any other Items, Re-fixing the Cover after cleaning of Manhole, Removing/ Carrying Silts, Sludge or any other Items to a distance exc. 50 Metre but not exc. 100 Metre and burried into Earth Pit (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg Per Sqm at Top of deposited Silts, Sludge or any other Items including Returning, Filling in, Dressing of Surplus Soils and Providing Ground to Slope, etc. (as required/ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative upto TWICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, T&P, Labours, Excavation of Earth Pit, etc. as required for Cleaning will deemed to be included in the Quoted Unit Rate.

M&L Cleaning MANHOLE of Depth exc. 0.50 METRE and not exc. 1.00 METRE, by Opening Cover and Taking out accumulated Silts, Sludge or any other Items, Re-fixing the Cover after cleaning of Manhole, Removing/ Carrying Silts, Sludge or any other Items to a distance exc. 50 Metre but not exc. 100 Metre and burried into Earth Pit (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg Per Sqm at Top of deposited Silts, Sludge or any other Items including Returning, Filling in, Dressing of Surplus Soils and Providing Ground to Slope, etc. (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative upto TWICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, T&P, Labours, Excavation of Earth Pit, etc. as required for Cleaning will deemed to be included in the Quoted Unit Rate.

M&L Cleaning MANHOLE of Depth exc. 1.00 METRE and not exc. 1.50 METRE, by Opening Cover and Taking out accumulated Silts, Sludge or any other Items, Re-fixing the Cover after cleaning of Manhole, Removing/ Carrying Silts, Sludge or any other Items to a distance exc. 50 Metre but not exc. 100 Metre and burried into Earth Pit (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg Per Sqm at Top of deposited Silts, Sludge or any other Items including Returning, Filling in, Dressing of Surplus Soils and Providing Ground to Slope, etc. (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative upto TWICE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, T&P, Labours, Excavation of Earth Pit, etc. as required for Cleaning will deemed to be included in the Quoted Unit Rate.

M&L Cleaning MANHOLE of Depth exc. 1.50 METRE and not exc. 2.00 METRE, by Opening Cover and Taking out accumulated Silts, Sludge or any other Items, Re-fixing the Cover after cleaning of Manhole, Removing/ Carrying Silts, Sludge or any other Items to a distance exc. 50 Metre but not exc. 100 Metre and burried into Earth Pit (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg Per Sqm at Top of deposited Silts, Sludge or any other Items including Returning, Filling in, Dressing of Surplus Soils and Providing Ground to Slope, etc. (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative upto ONCE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, T&P, Labours, Excavation of Earth Pit, etc. as required for Cleaning will deemed to be included in the Quoted Unit Rate.

M&L Cleaning SEPTIC TANK 10 USERS by opening Cover, Pumping out Sewage Water and taking out accumulated Night Soils, Sludges, Brick Bats or any other Items, re-fixing the Cover after cleaning of Septic Tank, removing and carrying Night Soils, Sludges, Brick Bats, etc. to a distance exc. 50 Metre but not exc. 100 Metre and burried (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg/Sqm on deposited Sludges at Earth Pit including Excavating of Earth Pits and Returning, Filling in, Dressing of surplus Soils and providing ground to Slope, etc., (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative only ONCE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, necessary Earth Works, Materials, T&P, etc. required for Cleaning will deem to be included in the Quoted Unit Rate.

M&L Cleaning SEPTIC TANK 25 USERS by opening Cover, Pumping out Sewage Water and taking out accumulated Night Soils, Sludges, Brick Bats or any other Items, re-fixing the Cover after cleaning of Septic Tank, removing and carrying Night Soils, Sludges, Brick Bats, etc. to a distance exc. 50 Metre but not exc. 100 Metre and burried (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg/Sqm on deposited Sludges at Earth Pit including Excavating of Earth Pits and Returning, Filling in, Dressing of surplus Soils and providing ground to Slope, etc., (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative only ONCE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, necessary Earth Works, Materials, T&P, etc. required for Cleaning will deem to be included in the Quoted Unit Rate.

M&L Cleaning SEPTIC TANK 50 USERS by opening Cover, Pumping out Sewage Water and taking out accumulated Night Soils, Sludges, Brick Bats or any other Items, re-fixing the Cover after cleaning of Septic Tank, removing and carrying Night Soils, Sludges, Brick Bats, etc. to a distance exc. 50 Metre but not exc. 100 Metre and burried (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg/Sqm on deposited Sludges at Earth Pit including Excavating of Earth Pits and Returning, Filling in, Dressing of surplus Soils and providing ground to Slope, etc., (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative only ONCE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, necessary Earth Works, Materials, T&P, etc. required for Cleaning will deem to be included in the Quoted Unit Rate.

M&L Cleaning SEPTIC TANK 100 USERS by opening Cover, Pumping out Sewage Water and taking out accumulated Night Soils, Sludges, Brick Bats or any other Items, re-fixing the Cover after cleaning of Septic Tank, removing and carrying Night Soils, Sludges, Brick Bats, etc. to a distance exc. 50 Metre but not exc. 100 Metre and burried (minimum 450mm below Normal Ground Level), Sprinkling Bleaching Powder @ 0.50 Kg/Sqm on deposited Sludges at Earth Pit including Excavating of Earth Pits and Returning, Filling in, Dressing of surplus Soils and providing ground to Slope, etc., (as required/ ordered at Site), complete all as specified and as directed. NOTE :- (a) The Item is Measurable/Operative only ONCE during the entire Contract Period. Any additional Cleaning if rquired, Contractor will Cleaning the same without any Extra Cost to the Department. (b) The Cost of Bleaching Powder, necessary Earth Works, Materials, T&P, etc. required for Cleaning will deem to be included in the Quoted Unit Rate.

D.D Construction

M/S CHANDAN ENTERPRISE

Kaushik Enterprises