PHC Birohar

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm. layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. (HSR 6.6)

Earth Filling Under Floors. (HSR 6.13) (a) earth filling under floors with surplus soil, excavated from foundation and taken only from outside the building plinth, in 15 cm layer including ramming, watering and consolidating lead upto 30 metres.

Dismantling Brick Wrok, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5) (b) In cement

Dismantlingg Concrete (HSR 8.6) (e) Reinforced cement concrete with cleaning and straightening and cutting of bars if required.

Dismantling Roofing (HSR 8.8) (g) demolishing mud phaska in tile terracing

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the wall is not to be dismantled (HSR 8.18) (a) Doors

Dismantling cement conglomerate / terrazzo-floors 25 mm to 50 mm thick including concrete base. (HSR 8.25)

Scrapping (HSR 8.32) (c) Cement plaster

Cement concrete 1:8:16 with brick ballast 40 mm nominal size in foundation and plinth (HSR 10.26)

Cement concrete 1:4:8 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.38)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respect. [HSR. 10.82 + 10.95 (a)].

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (Straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centring and shuttering, laid in position complete in all respects. [HSR. 10.86 + 10.95 (a)]

Cement concrete 1:1½:3 with stone aggregate 20mm nominal size for reinforced concrete work in footing, strips, foundation, rafts, pedestal and approach slabs of bridges etc. but excluding steel reinforcement and including centring and shuttering, laid in position, complete in all respects. (for work upto 1.5 Mtrs. below ground level.) [HSR. 10.90 + 10.95 (a)].

Providing and laying 60 mm thick ISI Marked interlocking paver blocks (conforming to IS 15658:2006) of all shapes and colours of design mix cement M-35 over a bed of 25 mm thick fine sand complete in all respect. (HSR 10.158)

First calss brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7)

Half Brick Masonry (HSR 11.48) (a) 11.43 cm thick brick wall laid in cement sand mortar 1:4 in spuer-structure.

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25mm mud mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Cement concrete 1:2:4 gola 10 cm X 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (HSR 13.64)

Providing & fixing PVC Rain Water pipe 6 Kg pressure of ISI mark in cement mortar during masonry work. (HSR 13.89) (a) 100 mm dia. PVC pipe 6 kg. pressure

(b) 150 mm dia. PVC pipe 6 kg. pressure

Providing & fixing PVC Bend ISI Mark (HSR 13.90) (a) 100 mm dia. PVC Bend

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, BELL, JOHNSONS, RAK, SIMPOLO & OASIS (HSR 14.89)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) (b) Size of ceramic Glazed tiles 300 x 450 mm

12 mm thick cement plaster 1:6 (HSR 15.7)

15mm Thick Cement Plaster 1:6 on the rough side of single or half brick wall. (HSR 15.12).

10 mm thick cement plaster 1:4 (HSR 15.52)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work. (HSR 16.57) (T.R.)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79) (T.R.) (b) 1st quality

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make) (HSR 16.81) (T.R.)

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (HSR 17.93) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35 mm thick

Providing and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming ot IS, 733 and IS: 1285 fixed with rawlplugs and screws orwith fixing clips or with expansion hold fasterners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat langle. Aluminium snap beading for glazing/paneling C.P. brass/ stainless steel screws, etc. complete. Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required including aluminium fitting. (HSR 17.96)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete. (HSR 17.97) (a) Pre-laminated particle board with decorative lamination on one side & balancing lamination on both side.

Providing and fixing glazing in aluminium door windows, ventilator shutter and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shallbe paid in basic items). (HSR 17.98) (a) With float glass panes of 4.00mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required embedding in floors and cover plates with brass pivot and single piece M.S.sheet outer box. (HSR 17.99) (b) With brass cover plate

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Fe -500 EQR TMT steel bars for RCC works where not included in the complete rate of RCC including bending , binding and placing in position complete (HSR 18.22)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent limer mortar 2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2;4 slab 100 mm thick./C.C. topping 50 mm thick with 455 mm x 455 mm 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint coplete as per standard design. (HSR 29.84) (a) Size 450 mm x 450 mm in side (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with C.C.topping)

(b) Size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping)

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described in item No. 30.1 (above) (HSR 30.2) (a) Size 580 mm (i) White

Providing and fixing in position best Indian make (as approved by the Engineer-in-charge) European type water closet suite, syphonic type consisting of (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH “P” or “S” TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND AKING GOOD THE WALLS AND FLOORS (HSR 30.5) (a) Single trap Syphonic W.C. Suite (ii) Single colour

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREIOUS CHINA WARE CISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings. (HSR 30.12) (i) White

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13) (i) White plastic seat (Solid)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as given below (to the approval of the Engineer-in-charge). (HSR 30.41) WHITE (v) Size 560 mm X 450 mm with one no. tap

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the walls etc. (HSR 30.70) (a) C.P.BRASS (i) Soap dish large

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71) (a) INDIAN MAKE (i) 600 mm X 450 mm

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). (HSR 30.75) (a) Bib cock long body

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge) (HSR 30.76) (a) 15 MM STOP COCK (ii) Concealed stop cock with flange

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION (HSR 30.82) (b) C.P. Brass (iii) 15 mm X 450 mm

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with ilet and outlet pipes, providing over flow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (Except civil work) (HSR 30.119) 1000 Ltr. Capacity

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (NS) (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

Providing, fixing and jointing union couplings in G.I. and W.I. pipelines. (NS) (a) 15 mm internal diameter

(b) 20 mm internal diameter

Sumit Kumar

R.S Enterprises

MAhaveer Sharma Contractor