Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.1 LAccepted-AOC | ₹1.1 L | L1 | Accepted-AOC QUOTED LOWEST |
| 2 | L2₹1.2 L+₹1,780 (1.56%)Rejected-Finance | ₹1.2 L+₹1,780 (1.56%) | L2 | Rejected-Finance QUOTED HIGHER THAN L1 |
| 3 | L3₹1.2 L+₹2,533 (2.22%)Rejected-Finance | ₹1.2 L+₹2,533 (2.22%) | L3 | Rejected-Finance QUOTED HIGHEST |
Tender Value
₹1.1 L
EMD Value
₹2,300
Closing Date
17 Feb 2026, 12:00 pmClosed
EE/WS/GRWW
GRWW, BIDHANGARH, KOL -66
SUPPLY AND INSTALLATION OF 600 MM DIA. NEW DISMANTLING JOINT IN THE DELIVERY SIDE PIPELINE OF V.T. PUMP NO-4 AT LLPS UNDER GRWW.
2026_KMC_1000022_1
KMC/WS/GRWW/PH-I/eT-29/2025-26
Open Tender
MECHANICAL
Percentage
GRWW
Please refer Tender documents.
3 documents required · 3 mandatory
₹0
₹2,300
8 Jul 2026
5 Feb 2026
19 Feb 2026
5 Feb 2026
17 Feb 2026
9 Feb 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | CHAPTER - III TAKING OUT PIPES AND SPECIALS Cast Iron /
Ductile Iron Pipes and SpecialsM.S. Pipes and Specials Taking out
M,S, Pipes with specials and valves including stacking the same
within a lead of 30M as per instruction of the Engineer-incharge(
Excavation. dewatering, earth filling etc. will be paid
separately).Pipe up to 750 mm diameter and depth of trench up to 2
Metre. | 1 | METER | 1,118 | ₹1,118 |
| 2 | CHAPTER - VII MISCELLANEOUS ITEMS Supplying including cost
of installation of cast iron Dismantling joint Double Flanged Flexible
Short piece with collapsible arrangement, flanged face drilled to IS:
1538-93 table 4 & 6, flat face conforming to IS: 210-85, GR 150 FG
complete with sealing rubber gasket made of EPDM quality with ISI
mark to 5382-1985, type 4, cast iron follower gland and mild steel
fastener with zinc coating. The whole assembly is to be mechanically
and hydraulically tested to provision in IS: 1533.93. Fitting and fixing
should be in proper position with proper care of main pipe line for leak
proof condition. Diameter in mm. with minimum barrel pipe length in
mm. 600mm with length 310 to 460mm. | 1 | EACH | 58,809 | ₹58,809 |
| 3 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I.
/ D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.1 Lowering
any type C I. pipes & specials and laying along trench at any depth as
per specification and direction of the Engineer-in-charge. [For laying over ground. the rates shall be reduced by 10 % and tile rates so reduced shall be inclusive of cost of holding arrengements) Diameter In mm 900mm dia. | 3 | METER% | 173.93 | ₹521.79 |
| 4 | CHAPTER - VIII SUPPLYING OF MATERIALS 8.4Supply of Flat
Rubber Gasket of EPDM Quality with ISI Mark to IS: 5382/1985
Type-4 suitable for flange joint, drilled to IS: 1538 (Table ... VI). The
gasket should have dual thickness 3/6mm with 6 mm thickness at the
sealing cross section.600mm dia | 2 | EACH | 618 | ₹1,236 |
| 5 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I.
/ D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.7Supplying
and fabricating 20 mm to 32mm thick (finished thickness) M.S flange.
properly ribbed, one face machined, including drilling holes as
perstandard table, fitting and fixing the same with M.S. pipe by
electric arc welding as per relevant I.S. specification using standard
electrodes and direction of the Engineer-in-Charge. [ The
Engineer-in-Charge shall approve the electrodes for arc welding
before use] 600mm dia | 2 | EACH | 14,285 | ₹28,570 |
| 6 | CHAPTER - VII MISCELLANEOUS ITEMS Coating of 'Epoxy' Resin
of thickness not less than 160 micron with a
lowviscosity,crystallization-resistant epoxy resin base with a reactive
diluents combined with high build epoxy amine adducts as per BS
5493 standard and a polyamide or amido polyamine or any other
suitable hardener. It shall react with epoxy resin at normal ambient
temperature, suitable for solvent-free coatings as per recommended
proportion for use on metal,concrete and wood surface to protect
from corrosion as well as damagefrom chemical reaction after making
the surface free from dust, oil and moisture etc. all complete as per
instruction and to the satisfaction of ElC. [This item will be operated
on prior permission from the concerned SE/Dy Chief Engineer] | 1.9 | SQUARE METER | 449 | ₹853.1 |
| 7 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS,
GATES ETC. A. ORIGINAL WORKS 7. Supplying, fitting, fixing bolts
with nuts, washer (ii) 20 to 25 mm dia bolt: (a) Length up to 75 mm
dia: | 40 | KILOGRAM | 115 | ₹4,600 |
| 200 | Estimated amount | - | - | - | - |
| 201 | Add: 9%SGST | - | LS | 13,091.41 | - |
| 202 | Add: 9%CGST | - | LS | 13,091.41 | - |
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.34 MB
BOQ_2449713.xls
BOQ • 0.23 MB
TBID.pdf
Tender Documents • 0.20 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .