GE/DE-60/2019-2020

Amount

Demolition of cement concrete, reinforced, of any type and in any position below or above ground level, complete all as specified and as directed.

Demolition, Cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness below or above ground level, complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc., to receive new plaster, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each and removing from site, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.50 Sqm and not exceeding 4 Sqm each and removing from site, complete all as specified and as directed.

Taking down shutters not exceeding 1.0 Sqm each and removing from site, complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0 Sqm and not exceeding 2 Sqm each and removing from site, complete all as specified and as directed.

Dismantling boarding, any description, fixed any position with with screws including cover fillets, complete all as specified and as directed.

Dismantling posts or struts(wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) & removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thickness including cover fillets, complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes including all fittings and accessories, 100/75 mm dia and in any position, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 15mm, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 25mm, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 32mm, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 40mmcomplete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 50mm, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for bore of pipe 80mm, complete all as specified and as directed.

Plain cement concrete 1:3:6, Type C-2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed.

Providing precast reinforced cement concrete 1:2:4 type B-0 using 12.50mm graded crushed stone aggregate in louvers and jallies, 35 mm thick (measured solid), including all mouldings but excluding frame (precast frame shall be measured separately) set in cement mortar 1:4, complete all as specified and as directed.

PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in packing in the sides/edges or other similar works, complete all as specified and as directed.

Precast cement concrete1:2:4 type B-0 using 12.50mm graded crushed stone aggregate, as in kerb stones, rounded and chamfered on edges and similar items, including necessary form work set in cement mortar 1:4, complete all as specified and as directed.

Providing PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in surface channels, complete all as specified and as directed.

Brick work with sub class “B” bricks straight or curved on plan exceeding 6mtr mean radius built in cement mortar 1:6 using old size bricks, complete all as specified and as directed.

All as per description of Srl Item No.- 27 here-in-before but except bricks, complete all as specified and as directed.

18-20mm thick Granite stone slab (table rubbed and polished) in steps, shelves, and the like not less than 1Sqm (in one piece), laid over 20mm thick layer of cement mortar 1:3 after rougheniung of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including moulding of edges, complete all as specified and as directed.

1st class Hard wood beading straight (any size) for glazed or gauzed joinery, renewed, including mitres etc., including removing old beading, complete all as specified and as directed.

19-20mm thick Block board, interior grade, commercial type, fixed with screws in cup boad shutter/pelmets/cabinet/wardrobe etc. or to timber frame work, fixed in repairs, complete all as specified and as directed.

Factory made flush shutter 35mm thick, Solid core construction with Block board and plywood face pannels, commercial type on both sides, complete all as specified and as directed.

Factory made 35mm thick second class hard wood for plain framed panelled shutters (any number of panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS: 1003(Part 1), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

Glazed and Skelton shutters using 2nd class hard wood, 35mm thick open rebated and prepared to receive glass or gauge etc., edges of framing plain and chamfered or fitted with cut or mitered beads for securing glass or gauze, size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square complete all as specified and as directed.

Glazed and Skelton shutters using 2nd class hard wood, 30mm thick open rebated and prepared to receive glass or gauge etc., edges of framing plain and chamfered or fitted with cut or mitered beads for securing glass or gauze, stiles and rails of window shutters to be provided as specified in SSR Part-I section 8, clause 8.23(b) and divided in square complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS squqre tube. complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail, lock on either side and gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointing together with solvent cement, supplying & fixing of frame at site, complete all as specified and as directed.

Continuous (Piano) hinges, brass body 30 mm width of flaps (when open), complete all as specified and as directed.

40mm dia cupboard knobs fixed with nuts, screw and washers of mild steel bright finished, powder coated, fancy type, complete all as specified and as directed.

125mm long Hasp and staple aluminium anodised including bolt to hinge plate and fixed with screws, complete all as specified and as directed.

Ball catches with 8mm dia steel ball, and bras body and striking plate including letting in and fixed, complete all as specified and as directed.

100mm size butt hinges (medium weight) colled rolled mild steel fixed with welding, complete all as specified and as directed.

75mm size butt hinges (medium weight) colled rolled mild steel fixed with welding, complete all as specified and as directed.

Extruded aluminium alloy handles fabricated type anodised of size 150mm size, complete all as specified and as directed.

Aluminium anodized 150mm size barrel tower bolt of extruded section and fixed, complete all as specified and as directed.

Aluminium anodized 100mm size barrel tower bolt of extruded section and fixed, complete all as specified and as directed.

Aluminium alloy anodised sliding door bolt with hasp, stape (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300mm size, complete all as specified and as directed.

Aluminium alloy anodised sliding door bolt with hasp, stape (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 250mm size, complete all as specified and as directed.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B- 21 of size 100mm, complete all as specified and as directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and as directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, and fixed with tinned tacks or galvanised mild steel staples, fixed in repairs, complete all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm, and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and as directed.

Mild steel mortice lock vertical type 150mm size 6 lever with all fittings and fixtures fixed in rapairs to wooden/Aluminium frames, complete all as specified and as directed.

Floor door stopper ( overall length of cover plate140 mm) of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in repairs in floors, complete all as specified and as directed.

Floor door stopper ( overall length of cover plate140 mm) of brass body and tongue, anodised with hard drawn steel spring fixed in repairs in floors, complete all as specified and as directed.

Aluminium ( Die cast ) body door closer hydraclically regulated designation No. 2 universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg, fixed in repairs, complete all as specified and as directed.

300mm size mild steel ordinary rat & tail rod pattern spring (Halical) including rollar & rollar plate fixed to wooden / MS frame, complete all as specified and as directed.

Curtain rod/rail with PVC coated mild steel rod fancy type 25 mm dia including bracket and fancy type end globes etc., complete all as specified and as directed.

Repair/ easing/ readjusting of aluminium / Glass door/ window shutters of any size, by taking down shutters from frame and dismantling members of shutters like, glass, rails and style by necessary cutting, grinding of members etc and refixing same including rubber gasket, hinges, handle screws etc, complete all as specified and as directed.

Repair/ easing/ readjusting of sliding glazed/gauzed shutters of any description, by taking down shutters from frame/channel and dismantling members of shutters like, glass, rails and style by necessary cutting, grinding of members etc and refixing same including rubber gasket, hinges, handle screws etc, complete all as specified and as directed.

Repair/ easing/ readjusting of steel garage shutters of any description by taking down of complete shutters from fixing arrangement/pintel hinges including necessary cutting, grinding, welding and greasing of members etc., inserting hold fasts in PCC blocks, and refixing the same in proper position with one coat of synthetic paint, complete all as specified and as directed.

Anodised aluminium doors (sliding/hanging type) with frame size 101.60X44.45X 2.00 mm thick and shutter aluminium anodised and top rail 47.62X 44.45 X 1.50mm and style 47.5 x 44.5 x1.5 mm , lock rail 83.50X 44.45 X 1.50 mm and bottom rail150.00X 44.50 X 2.50 mm incl necessary aluminium fittings like aluminium butt hinges 04 Nos , aluminium handles 150mm 02 Nos,aluminium tower bolts 200mm 01No, mortice lock 4 lever MS, hydraulic door closer of suitable capacity 01 No, aluminium door stoper 01 Nos, jointing cleats,glazing cleats,rubber packing , anodised aluminium shape beading, screws etc with panelling in two parts with 12mm thick prelaminated partical board in lower panel and 5mm thick tinted glass in upper panels incl all fittings& fixture, complete all as specified and as directed.

Anodised aluminium (hanging type) windows/ventilator with frame size 60x40x2.00mm thick and shutter with section bearing bottom 25x18x1.50, top 39.4x17.7 X1.50 mm fixed over top of frame work , top and side section of size 61.6 x 31.75x1.5mm and bearing bottom track of size 61.6x 31.75x1.5mm or fixing with hinges including necessary aluminium jointing cleats, glazing cleats, rubber packing anodised snape beading, screws etc with 4 mm thick tinted/ plain glass in panels incl all fitting and fixture, complete all as specified and as directed.

Aluminium anodized grills with 6mm-5mm thick aluminium section having square gap of 100mm size with fixing rails of channels 12-15mm, complete all as specified and as directed.

Box type Steel windows with double shutters (inside for wiremesh & out side for glass), including guard bar, hinges, steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded including a coat of red oxide after preparation of surface before fixing all as shown in drg No. TD-A sheet 1/3 to 3/3, complete all as specified and as directed.

Mild steel round bars 10mm dia bars cut to length, bend to shape as required including cranking, hooking ends for tying/tightening wire mesh, complete all as specified and as directed.

Mild steel angle iron post and struts in fencing incluidng cutting tops to shape, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe 290 Gde-E complete all as specified and as directed.

Galvanised mild steel chain link fencing, including line wires made from 3.15mm dia GI wire, mesh size 50mm x 50mm selvaged with one end of fabric knuckled and twisted on other end of tensile strength 550MPa conforming to IS : 280, fixed to standard rails, with straining bolts, etc., including provision of binding wire any fixed in repair, complete all as specified and as directed.

Fixing only chain link fencing, including line wires, any mesh, size and type to any type of standard rails, with straining bolts, etc., including provision of binding wire any, complete all as specified and as directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including hooks and hanging or sliding with and including hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rail and guides) and hanging, also fastening and fixing, complete all as specified and as directed.

Mild steel, 0.80mm thick plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and as directed.

0.50mm thick prepainted galvalume aluminium zinc coated GI based semi corrugated/profile steel sheeting of any colour, having tensile strength of 550MPA as in roof covering, wall cladding with self tapping screws as per manufacturers instructions, complete all as specified and as directed.

0.63mm thick plain black sheet in wall cladding, steel gates and similar works, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up with mitred angles etc., as required, complete all as specified and as directed.

Aluminium anodised snap grid frame work of size 605mm x 605mm for false ceiling with hanging arrangement of 6mm dia GI wire (upto 1200mm length) with level adjustable system provisioned, fixed to roof slab by means of ceiling cleats made out of GI flat 40mm x 3mm size and 60mm long, expansion hold fasteners 12.50mm dia 40mm long, complete all as specified and as directed.

4mm thick non-asbestos cement fibre based building boards fixed or laid/inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

75 mm thick plain cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub base finished even and fair, complete all as specified and as directed.

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 60mm thick, M-35 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with no pigments to match colour of blocks in floors laid over 30mm thick sand cushioning, complete all as specified and as directed.

Vibro compacted Precast concrete interlocking paver blocks, factory made,any shape and size conforming to IS- 15658- 2006 of 60mm thick, M-35 Grade set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors laid over 30mm thick sand cushioning, complete all as specified and as directed.

Pre-polished coloured chequered cement concrete tiles, factory made, Premium quality 200mm x 200mm x 25mm thick, set, jointed in neat cement slurry and pointed flush with grey cement and no pigments to match colour of blocks in floors over 15 mm thick screed bed or bedding layer in cementy mortar 1:4, complete all as specified and as directed.

Pre-polished coloured chequered cement concrete tiles, factory made, Premium quality 200mm x 200mm x 25mm thick, set, jointed in neat cement slurry and pointed flush with grey cement mixed with pigments to match colour of blocks in floors over 15 mm thick screed bed or bedding layer in cementy mortar 1:4, complete all as specified and as directed.

Plain cement concrete 40mm thick 1:2:4 type B- 1 using 20mm graded crushed stone aggregate as in floor finish and finishing the surface even and smooth without using extra cement and laid in alternate bays and provided with grooves complete all as specified and as directed.

Supply only glass dividing strips 38mm wide and 3mm thick, complete all as specified and as directed.

75mm thick plain Cement Concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays laid in alternate bays (not exceeding 2 Sqm each) finished even and fair without using extra cement, complete all as specified and as directed.

Stamped concrete 1:1.5:3 type A-1 (using 20mm grade crushed stone aggregate) as per manufacturer's instructions in sub base finished evern and fair, complete all as specified and as directed. Make : Unistone Large Ashlar stone or Adhlar Slate or Castle Stone.

75mm thick Stamped concrete 1:1.5:3 type A-1 (using 20mm grade crushed stone aggregate) laid on green concrete of approved design/pattern/size as floor set as per manufacturer's instructions, complete all as specified and as directed. Make : Unistone Large Ashlar stone or Adhlar Slate or Castle Stone

Non skid ceramic joint less coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18Sqm but not exceeding 0.38Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

Glazed Coloured Ceramic tiles in vertical surface 350mm x 250mm or 450mm x 300mm and 7mm thick set and joint in neat cement slury and pointed in white or colour cement to match laid over 10 mm thick screed bed in cement mortar 1:4, including dismantling of old tiles, complete all as specified and as directed.

Raking out joints/pointing in cement mortar provided to brick masonry in walls, bricks on edge in floors or surface channels etc., complete all as specified and as directed.

Flush pointing in cement mortar 1:3 provided to bricks on edge in paving, complete all as specified and as directed.

Rendering 5 mm thick in cement mortar 1:3 in ceilings finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement, complete all as specified and as directed.

Preparation of newly plastered external surfaces of walls and applying two coats of cement based paint, complete all as specified and as directed.

Preparing newly plastered surfaces of ceilings and applying two coats of oil bound distemper over a layer of 2mm thcik JK/Birla wall care putty for a even and fair surface, complete all as specified and as directed.

Providing and applying waterproof cement based putty over the plastered/ old painted wall after scrapping to prepare the surface even and smooth, complete all as specified and as directed. Step 1) Mix the putty with water as per requirement to mix properly. Step 2) Apply the prepared mix with the help of mechanically/manually as per site requirement. Step 3) Allow 6-8 hrs time to dry the putty surface.

Sanding of the putty surface manually/mechanically by skilled labour as per site requirement to prepare the surface and remove loose dust etc., before applying finishing coat, complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper, complete all as specified and as directed.

Preparing newly plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed.

Preparation of old decorated surfaces of walls including washing, rubbing, down and stopping of old painted surfaces and applying one coat of cement base paint, complete all as specified and as directed.

Preparation of old decorated surfaces of walls/ceilings including washing, rubbing, down and stopping of old painted surfaces and applying one coat of plastic emulsion paint, complete all as specified and as directed.

Preparation of old decorated surfaces of walls including washing, rubbing, down and stopping of old painted surfaces and applying one coat of weather proof exterior emulsion paint, complete all as specified and as directed.

Preparation of old decorated surfaces of walls including washing, rubbing, down and stopping of old painted surfaces and applying one coat of white wash, complete all as specified and as directed.

Preparation of new wooden surfaces and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint on surfaces of any description exceeding 10 cm width or girth over a coat of red oxide complete all as specified and as directed.

Preparation of new brick, stone, concrete or cement plastered surfaces and applying two coat of synthetic enamel paint over a coat of priming paint on surfaces of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

Hacking out old broken glasses any thickness size, quality or description from wooden frames fixed with putty or with beads, hacking to be done in buildings of any height, complete all as specified and as directed.

Hacking out old broken glasses any thickness size, quality or description from metal frames including punching or drilling out old glazing pins/spring clips and providing new ones, hacking to be done in buildings of any height, complete all as specified and as directed.

Sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm.in each pane, complete all as specified and as directed.

3.00mm thick figured glass, pin headed type, and glazing with oil putty in square not exceeding 0.5 Sqm.in each pane, complete all as specified and as directed.

5.00mm thick figured glass, pin headed type, and glazing with oil putty in square exceeding 0.5 Sqm.in each pane, complete all as specified and as directed.

Cutting chases for concealed water tubing girth exceeding 10cm but not exceeding 20cm girth and making good in cement mortar 1:3 in brick walls, complete all as specified and as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

25mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

32mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

40mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

50mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

80mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs, complete all as specified and as directed.

Vitreous china wash down closet pan (pedestal pattern), white with "S" trap, including plastic seat and cover and connecting to outgoing pipe, flush pipe and anti syphonage pipe, fixed in repairs, complete all as specified and as directed.

PVC valve less syphonic action type coloured flushing cistern, low level, 10 litres capacity including flush pipe PVC connection, float valve, PVC handle/button and connections complete including taking down old unserviceable flushing cistern any type, fixed in repairs, complete all as specified and as directed.

Health faucet with one metre long flexible tube in chrome finish fixed in position with brass chromium plated nuts for 15mm bore tubing, fixed in repairs, complete all as specified and as directed. (Make : Cat Part No. ALD-CHR593N of Jaquar/Cat part No. F160001 of Hindware/ Cat No F8030103 of Cera or equivalent in Somany).

Lead only for Health faucet one metre long flexible tube in chrome finish fixed in position with brass chromium plated nuts for 15mm bore tubing, fixed in repairs, complete all as specified and as directed.

CP brass soap dish, fixed in repairs, complete all as specified and as directed. Make Hindware Cat Part No F880011/ Cera Cat Part No. F5003106 or equavalent in /Somany/Jaquar.

Vitreous china wash basin under counter oval type size 560x450x175mm, fixed in repairs, Make :- Cera,jaquar, Hindware or eqvilent under granite slab with all fitting and fixture, fixed in repairs, complete all as specified and as directed.

Fancy type sink mixer for mixing hot and cold water with swinging port, screwed for iron pipe,15mm bore, fixed in repairs, complete all as specified and as directed. (Make : Cat Part No. 3002581 of Cera/Cat Part No. 200360061 of Somany/Cat Par No. 200023CP of Hindware or equivalent in Jaquar.

32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, complete all as specified and as directed.

Sand cast iron soil waste and vent pipes 100mm dia, in any length, with cement joints, laid in trenches including necessary excavation and earth work conforming to IS-1729, complete all as specified and as directed.

Sand cast iron soil waste and vent pipes 75mm dia, in any length, with cement joints, laid in trenches including necessary excavation and earth work conforming to IS-1729, complete all as specified and as directed.

CI bend for 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

CI bend for 75mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

CI branch piece equal or unequal (single 'T') 100mm bore any radius, diminishing pieces or tapers (larger bore measured), fixed to walls, complete all as specified and as directed.

CI floor trap, with grating including jointing to 100mm bore waste pipe fixed in cement concrete 1:2:4, type B-1, complete all as specified and as directed.

CI floor trap, with grating including jointing to 75mm bore waste pipe fixed in cement concrete 1:2:4, type B-1, complete all as specified and as directed.

PTMT Grating dome 125mm dia with or without hole for waste pipe fixed in repairs, complete all as specified and as directed.

Towel ring fixed in positon with and including chromium plated brass screws and wooden/plastic cleats, fixed in repairs, complete all as specified and as directed. Cat (Make : Part No. 5002109 of Cera or equivalent in Hindware/Jaquar/Somany).

Stop valve fancy type 15mm bore cast copper alloy, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipes or for unions, fixed in repairs, complete all as specified and as directed. (Make : Cat Part No. ALD-083, ALD-089, ALD081 of Jaquar/or equivalent in Cera/Somany/Hindware).

Wall mixer 3- in - 1 system (L-bend) with provision for overhead shower complete with 115mm long bend pipe connecting legs and over head shower with all fittings and fixtures, fixed in repairs, complete all as specified and as directed. (Make : Cat Part No : 5273 UPR of Jaquar/or equivalent in Cera/Somany/Hindware).

15mm bore bib tap chromium plated brass, Fancy type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

Angle valve 15mm bore dia or pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, fixed in repair, complete all as specified and as directed. (Make- Cera Cat part No 3002210/or equivalent in Jaquar/Hindware/Somany)

32 mm spring type PVC waste pipe fixed toWHB and urinals, ( Note minimum length of each pipe should not be less than 0.80RM), fixed in repairs, complete all as specified and as directed.

CP brass shower rose fancy type 150mm x 150mm size with shower arm 125mm size fixed in repair to 15mm bore pipe, complete all as specified and as directed. Make : Somany Cat Part No. 240406/Cera Cat Part No. F7010506/Hindware Cat Part No. 240806

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 15mm bore, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 25mm bore, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 32mm bore, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 40bore, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 50mm bore, complete all as specified and as directed.

Gun metal globe or gate valve screwed down high pressure with iron wheel head, screwed both ends for iron pipe 80mm bore, complete all as specified and as directed.

15mm bore PVC connection of size 450mm long with chromium plated brass end nuts, fixed in repairs, complete all as specified and as directed.

15mm bore PVC connection of size 600mm long with chromium plated brass end nuts, fixed in repairs, complete all as specified and as directed.

15mm bore brass chromium plated basin mixer of mixing 'Hot' and 'Cold' water with long shank, screwed down for iron pipe, fixed in repairs, complete all as specified and as dircted. (Make : Cat No 220912 of Somany/ Cat Part No F3001461 of Cera/Cat Part No. F330014 of Hindware or equivalent in Jaquar).

Sink made of stainless steel 1mm thick for kitchen or laboratory with plugs, washer and wastes, including in cement mortar to dwarf wall or including fixing cantilever brackets and connnecting union to pipe over all size 495mmx420mm bowl size 410mmx330mmx160mm with all fitting and fixture, fixed in repairs. complete all as specified and as directed.

Waste 40mm fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed, complete all as specified and as directed.

Waste 32mm fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed, complete all as specified and as directed.

PVC flushing cistern, float valve, PVC handle/button and connections complete including taking down old unserviceable flushing cistern any type, fixed in repairs, complete all as specified and as directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, fixed in repair, complete all as specified and as directed.

Brass spindle suitable for 15 mm bib cock / stop cock/ concealed stop cock/ angle cock, fixed in repairs, complete all as specified and as directed.

Brass spindle half turn suitable for 15 mm bib cock / stop cock/ concealed stop cock/ angle cock, fixed in repairs, complete all as specified and as directed.

Plastic water closet seat cover white, suitable for cascading or wall hung type WC closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixed in repairs, complete all as specified and as directed.

Plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixed in repairs, complete all as specified and as directed.

Removing of rubbish, mud, surbs, vegitation etc from existing drain including removing and replacing of covers, cleaning to make the drain serviceable completely including removing the taking out materials to a distance exc 50mtr or in suitable location complete all as specified and as directed.

Factory made Precast SFRC man hole covers of size 600mm x 450mm x 100 mm thick medium duty conforming to IS-12592 having weep holes for draining surface water, including frame with necessary lugs/hold fasts for embedding in concrete , complete all as specified and as directed.

NOTE:- For minimum fair wages, EPF and payment to labour employed, refer Sch A Note No-17,18 and Special Condition No 5 & 21.2 of this tender. Contractor must produce all the relevent record such as payment made to labour, EPF etc at the time of payment of RARs/Final bill. No payment will be released to contrator without producing the proper record.

NOTE:- Irrespective of whatever specified elsewhere in tender documents, all the debris/waste materials produced out of above mentioned work shall be removed out of Cantonement land and disposed off at locations notified by the Delhi Cantonment Board for disposal of waste building materials within NCR area, without any extra cost to Department under own arrangement of contractors. The rates quoted by the contractors against the items catered here-in-above in the BOQ are inclusive of said provision.

R. S. Associates

imran construction company

M/s Shubh Enterprises

M/s Durga Traders

GAUTAM ELECTRIC WORKS

sunil traders