GE(S) BTD TOKEN NO 01 OF 2022-23 REPAIR MAINTENANCE OF WOODEN AND STEEL FURNITURE ARTICLES AT BATHINDA MIL STN UNDER GE(S) BATHINDA

Amount

M & L to repairs Bed plywood top by replacing the following unserviceable parts with first class teakwood. Rest all as per drawing and directed by Engr-in-charge. (Drg No. FD-246/247/213)

Long leg.

Short leg.

Long rail.

Stiffener.

M & L 3.5 thick teak face plywood, including half round teakwood beading if broken, of both side of head rest complete.

M & L 3.5 thick teak face plywood, including half round teakwood beading if broken, of both side of foot rest complete.

S & F Plywood 12mm thick(9 ply) BWR Gde of suitable size (1980mm x 920mm)in single piece as per shown in drg.

M&L to repair Table Peg by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde).Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-384/277/236)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 15mm dia of approved quality.

M&L to repair Teapoy by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by engr-in-charge. (DRG NO. FD-382/278/232/34)

Top (460mm x 610mm) made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 20mm dia of approved quality.

M&L to repair Table Center by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-134/235/ 274)

Top (910mm x 460mm) made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Bottom rail made out of first class teakwood.

S&F PVC shoe 20mm dia of approved quality.

M&L to repair Table 900mm x600mm without drawer by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde).Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-284/231/223/55/42(M))

Top made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front/rear rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 20mm dia of approved quality.

M&L to repair Table 900mm x600mm with drawer by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-283/224/41)

Top (910mm x 610mm) made out of 18mm thick pre-laminated exterior grade MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front/side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

Back rail made out of first class teakwood.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated paticle board and 4mmx18mm teakwood beading complete excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12 mm thick plywood BWR Gde complete.

S&F PVC shoe 20 mm dia of approved quality.

M&L to repair Table 900mm x900mm by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawing and directed. (DRG NO. FD-291)

Top (910mm x 910mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawing and directed by Engr-in-charge.

Leg made out of first class teakwood.

Rail made out of first class teakwood.

S&F PVC shoe 25mm dia of approved quality.

M&L to repair Hat stand with mirror by replacing the following parts with approved ones. Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-233/361)

Plywood 3.5/4mm thick OSTF.

First class TW beading at all around of frame.

Mirror 5mm thick.

Brass peg 115-120mm long.

Aluminium nail hook 50mm long.

M&L to repair Table dining (1200mm x900mm) by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawing and directed by Engr-in-charge. (DRG NO. FD/MAP-II/03)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawing and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front/rear rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 25mm dia of approved quality.

M&L to repair Table dining 6 person by replacing the following unserviceable parts with teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by engr-in-charge. (DRG NO. FD-273/239/30(M)/FD/MAP-II/03)

Top (1510mm x 910mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 25mm dia of approved quality.

M&L to repair Table dining 8 person by replacing the following unserviceable parts with first class teakwood /prelaminated MDF Board (exterior gde). Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-273/239/30(M))

Top (1810mm x 910mm) made out of 18/19mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood.

Front rail made out of first class teakwood.

Side rail made out of first class teakwood.

Stiffener made out of first class teakwood.

S&F PVC shoe 25mm dia of approved quality.

M&L to repair Table dressing gents with mirror by replacing the following unserviceable parts with first class /teakwood/prelaminated MDF board (exterior gde)/plywood BWR gde.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-230/31(M))

Top made out of 18mm thick pre-laminated MDF board exterior gde OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided teakwood beading infront of suitable size.

All as per item no 12.01 but bottom complete.

All as per item no 12.01 but side complete.

Back ply of base made out of plywood 12mm thick( 9 ply) BWR gde complete.

Only Mirror 5mm thick of suitable size.

Back of mirror made out of plywood 6mm thick BWR Gde complete.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated MDF board and teakwood beading complete excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12 mm thick (9ply) plywood BWR Gde complete.

M & L to repairs Table dressing ladies with mirror by replacing the following unserviceable parts with first class teakwood/prelaminated MDF board 9exterior gda)/plywood MR gde. Rest all as per drawings and directed by Engn-in-charge. (Drg No. FD-251/32(M)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided teakwood beading infront.

All as per item no 13.01 but bottom complete.

All as per item no 13.01 but side complete.

Back ply of base made out of plywood 12mm thick (9ply) BWR gde complete.

Only Mirror 5mm thick of suitable size.

Back of mirror made out of 6mm thick BWR Gde plywood.

Plain glass 5 mm thick for sliding.

Aluminium channel complete of suitable size for sliding of glass.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated MDF board and 4mmx18mm teakwood beading complete excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12 mm thick (9ply) plywood BWR Gde complete.

Leg with frame made out of first class teakwood.

M&L to repair Side board by replacing the following items with teakwood /prelaminated MDF board (exterior gde)/ plywood BWR Gde.Rest all as per drawings and directed by Engineer-in-Charge. (DRG NO. FD-241/371)

Top made out of 18mm thick pre-laminated MDF board exterior grade OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided first class teakwood beading infront of suitable size.

All as per item No 14.01 but bottom complete.

All as per item No 14.01 but side complete.

All as per item No 14.01 but partition complete.

All as per item No 14.01 but single shutter duly provided teakwood beading on edges complete excluding knob.

All as per item No 14.01 but shelf 18mm thick complete.

Back ply 6mm thick BWR gde complete.

Legs with complete frame made out from first class teak wood.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated MDF board and 4mm x 18mm teakwood beading excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12mm thick (9 ply) plywood BWR gde complete.

M&L to repair Bin linen multipurpose by replacing the following items with teakwood /prelaminated MDF board (exterior gde)/ plywood BWR gde. Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD/E6/MAP/09)

Top made out of 18mm thick pre-laminated MDF board exterior grade OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided first class teakwood beading infront of suitable size.

All as per item No 15.01 but bottom complete.

All as per item No 15.01 but side complete.

All as per item No 15.01 but partition complete.

All as per item No 15.01 but single shutter (left) duly provided teakwood beading on edges complete excluding handle.

All as per item No 15.01 but single shutter (right) duly provided teakwood beading on edges complete excluding handle.

All as per item No 15.01 but shelf (left) complete.

All as per item No 15.01 but shelf (right) complete.

Back ply 12mm thick (9 ply) BWR gde.

Legs with complete frame made out from first class teak wood.

Drawer complete excluding handle.

Front of drawer made out of 18mm thick prelaminated MDF board and teakwood beading of suitable size excluding handle.

Bottom of drawer made out of 18mm thick prelaminated MDF board complete.

Side/back of drawer made out of 18mm thick prelaminated MDF board and PVC beading of suitable size.

CP handle 100mm long of approved quality.

M&L to repair Table writing by replacing the following unserviceable parts with first class teakwood/prelaminated MDF board (exterior gde)/plywood BWR gde.Rest all as per drawings and directed. (DRG NO. FD-275/249/33(M))

Top (1150mm x 610mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

Leg made out of first class teakwood complete.

All as per item no 16.02 but front rail complete.

All as per item no 16.02 but side rail complete.

All as per item no 16.02 but side stiffener complete.

All as per item no 16.02 but center stiffener complete.

All as per item no 16.01 but side of cabinet complete.

All as per item no 16.01 but bottom of cabinet complete.

All as per item no 16.01 but shutter of cabinet complete.

Back of cabinet made out of plywood 6mm thick BWR gde.

Shelf of cabinet made out of plywood 12 mm thick BWR gde complete.

Drawer complete excluding knob.

Front of drawer made out of 18mm thick prelaminated MDF board and 4mmx18mm teakwood beading complete excluding knob.

Bottom of drawer made out of plywood 6mm thick BWR Gde complete.

Side/back of drawer made out of 12 mm thick (9ply) plywood BWR Gde complete.

Brass lock of suitable size with duplicate key complete.

M&L to repair Sofa set 5/4 seater by replacing the following unserviceable parts with first class teakwood.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-281/373)

Side rail.

Batton seat/back.

Front rail of single seater.

Front rail of three seater.

Back rest rail top/side of single seater.

Back rest rail side of three seater.

Back rest rail top of three seater.

Removing old foam cushion with tapestry cloth and S&F new P.U.Foam cushion of size 530mmx560mmx100mm (40 density) duly covered with approved quality of tapestry cloth.Make of foam cushion:- sleepwell (Feather Foam) / Kurl-on (Komfort universe goldline plus) / Corfom (Premium Foam) . Note:- Cost of tapestry cloth shall be between Rs 200/- to Rs 250/- per mtr.

Removing worn out tapestry cloth from old cushion and replacing the same with new tapestry cloth of approved quality. Note:- cost of tapestry cloth shall shall be between Rs 200/- to Rs 250/- per mtr.

M&L to repair TV Trolley by replacing the following unserviceable parts with first class teakwood/prelaminated MDF board (exterior gde)/plywood BWR gde complete all as specified and directed. (DRG NO. FD/E6/MAP/04)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side with half round teakwood beading all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners complete all as specified and directed.

All as per item no 18.01 above but bottom complete.

All as per item no 18.01 above but shelf complete.

All as per item no 18.01 above but side complete.

All as per item no 18.01 above but back complete.

Glass shutter 5mm thick with hinges of suitable size.

Wheel roller of approved quality.

Magnet catcher of suitable size.

Taking out carefully old existing Knob from side board, table dressing gents, table dressing ladies etc and S&F new decorative Knob 32mm dia of approved quality complete all as specified and directed.

Taking out u/s Bearer of suitable Size from different type of tables likes side board, table writing, table 900 x 600mm with drawer etc and S&F new Bearer of suitable size, made out of first class teakwood complete all as specified and directed.

M & L for preparation of old wooden polished surface of Bed Hard FD- 246/247/213 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table Peg FD-384/277/236 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Teapoy FD-382/278/232/34 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table Center FD-134/235/274 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table 900X600mm without drawer FD-284/231/223/55/42(M) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table 900X600mm with drawer FD-283/224/41 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table 900X900mm FD-291 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dining 1200x900mm FD-FD/MAP-II/03 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dining 6 pers FD-273/239/30(M)/FD/MAP-II/03 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dining 8 pers FD-273/239/30(M) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Hat stand with mirror FD-233/361 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dressing gents with mirror FD-230/31(M) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table dressing ladies with mirror FD-251/32(M) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Side Board FD-241/371 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Bin linen multipurpose FD-FD/E6/MAP/09 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Table writing FD-275/249/33(M) by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Sofa set 5 seater FD-281/273 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of Sofa set 4 seater FD-281/273 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

M & L for preparation of old wooden polished surface of TV Trolley FD/E6/MAP/04 by rubbing down the old polish from wooden surface with sand paper,removing pluck mark with wooden scraper,cleaning of dirt and stopping holes by filling putty (Mixture of fine saw dust, fevicol, water and colour) and adding colour (Raw Sienna/Brunt Sienna/Turky Umber) of required quantity to obtain the desired colour, wiping off superfluous filler and allow to dry, rubbing off surfaces with sand paper until smooth surfaces is achived, wiping off the polish from other than wooden surfaces with polish thinner and applying lacquer polish till glossy finish is achieved complete all as specified and directed.

Preparation of old painted iron and steel surface (externally & internally complete) of Almirah large steel/Almirah steel 1/2H 1/2shelf FD-1031/67(M)/FD/E6/MAP/18 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface (externally & internally complete) of Almirah medium steel FD-1032/243/67(M) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface (externally & internally complete) of Locker steel FD-1029/257 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface of Table 900x600x760 mm with drawer FD-1008 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed. Note - Wooden portion of table 900x600x760 shall be lacquer polished with high gloss finish complete all as specified and directed.

Preparation of old painted iron and steel surface (Externally & internally complete) of Table office Clk Steel FD-1004/381/307/84(M) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed. Note - Wooden portion of table office clk steel shall be lacquer polished with high gloss finish complete all as specified and directed. Note - Wooden portion of table Office Clk Steel shall be lacquer polished with high gloss finish.

Preparation of old painted iron and steel surface (Externally & internally complete) of Table Office offr Steel FD-1002/1003/84(M) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed. Note - Wooden portion of table office offr steel shall be lacquer polished with high gloss finish. Note - Wooden portion of table Office Offr Steel shall be lacquer polished with high gloss finish.

Preparation of old painted iron and steel surface of Table bed side (MAP) FD/E6/MAP/15, FD/E6/MAP/15(R) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed. Note - Wooden portion of table bed side (MAP) shall be lacquer polished with high gloss finish complete all as specified and directed. Note - Wooden portion of table bed side (MAP) shall be lacquer polished with high gloss finish.

Preparation of old painted iron and steel surface of Bed Hard steel (MAP) FD/E6/MAP/8,FD/E6/MAP/8(R) by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed.

Preparation of old painted iron and steel surface of Table Computer FD/E6/MAP/03 by scraping & rubbing down with sand paper, removing dents & scratches if any, filling the same with paste filler and applying a coat of synthetic enamel paint (1st Gde quality) by brush or by spray machine complete all as specified and directed. Note - Wooden portion of table Computer shall be lacquer polished with high gloss finish.

M&L to repair Almirah steel large/Almirah steel 1/2H 1/2shelf by replacing the following unserviceable parts with approved ones.Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-1031/ 67(M))/FD/E6/MAP/18)

MS lock 6 lever with duplicate key.

Chromium plated handle 150mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer.

Pane glass 3.5/ 4mm thick of almirah glazed large steel.

Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

M&L to repair Almirah medium/small steel by replacing the following unserviceable parts with approved ones.Rest all as per the drawings and directed by Engr-in-charge.(DRG NO. FD-1032/243/67M))

MS lock 6 lever with duplicate key.

Chromium plated handle 150mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

Pane glass 3.5/ 4mm thick of almirah small glazed steel.

Note:- Pattern and shape of lock and handle will be determined as per actual requirement at site.

M&L to repair Locker steel by replecing the following parts with approved ones.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-257/1029)

Chromium plated hasp and staple 75mm long.

Chromium plated handle 100mm long.

Leg made out of 1mm thick MS sheet duly painted with one coat of red oxide primer

MS hinge 75mm long.

M&L to repair Table 900mm x 600 mm with drawer by replacing the following parts with approved ones as mentioned below and as per the drawing and directed by Engr-in-charge. (DRG NO. FD-1008 )

MS lock of suitable size with duplicate key.

PVC handle of approved quality suitable for drawer.

Making the drawer functional by removing dents from MS sheet align and leveling the drawer and greasing it grooves so as to achieve smooth sliding complete.

Top (910mm x 610mm) made out of 18mm thick pre-laminated MDF board (exterior gde) one side classic walnut face and balancing white on other side duly teakwood beading 4x18/19mm all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

S&F PVC/hard rubber toe of approved quality and suitable size.

M&L to repair Table 900mm x 600mm without drawer steel by replacing the top (910mm x 610mm)made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawing and directed by Engr-in-charge. (DRG NO. FD-1007 )

Preparation of old surface of Table 900mmx600mm without drawer steel by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) OG colour complete.Rest all as specified and directed.

S&F PVC/hard rubber toe of approved quality and suitable size.

M&L to repair Table 900mm x 900mm steel by replacing the top (910mm x 910mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-1009 )

Preparation of old surface of Table 900mmx900mm steel by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) OG colour complete.Rest all as specified and directed.

S&F PVC/hard rubber toe of approved quality and suitable size.

M&L to repair Teapoy verandah by replacing the top (910mm x 460mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-255 /208/ 35 )

Preparation of old surface of teapoy verandah by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) white colour complete. Rest all as specified and directed by Engr-in-charge. (DRG NO.FD-255 /208/ 35)

S&F PVC toe for teapoy verandah of approved quality and suitable size.

M&L to repair Teapoy verandah (MAP) by replacing the top (760mm x 460mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawing and directed by Engr-in-charge. (DRG NO.FD/E6/MAP/17 )

Preparation of old surface of teapoy verandah MAP by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) black colour complete. Rest all as specified and directed by Engr-in-charge. (DRG NO. FD/E6/MAP/17)

S&F PVC/Hard rubber toe for teapoy verandah (MAP) of approved quality and suitable size.

Spot welding on various items of steel furniture FD/TP

M&L to repair Table clerk (steel) by replacing the following parts with approved ones.Rest all as per the drawings and directed by Engr-in-charge. (DRG NO. FD-1004/381/307/84(M)).

MS lock of suitable size with duplicate key.

S&F PVC handle of approved quality suitable for drawer.

Making the drawer functional by removing dents from MS sheet align and leveling the drawer and greasing it grooves so as to achieve smooth sliding complete.

Top (1220mm x 610mm) made out of 18mm thick pre-laminatedexterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners . Rest all as per the drawings and directed by Engr-in-charge.

S&F PVC/Hard rubber toe of suitable size.

M&L to repair Table officer (steel) by replacing the following parts with approved ones.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD-1003/84(M)).

MS lock of suitable size with duplicate key.

S&F PVC handle of approved quality suitable for drawer.

Making the drawer functional by removing dents from MS sheet align and leveling the drawer and greasing it grooves so as to achieve smooth sliding complete.

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners. Rest all as per the drawings and directed by Engr-in-charge.

S&F PVC/Hard rubber toe of suitable size.

M&L to repair Table bed side (MAP) by replacing the following parts with prelaminated MDF board(exterior gde)/plywood BWR gde. Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD/E6/MAP/15, FD/E6/MAP/15(R))

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided with teakwood beading of suitable size complete all as specified and directed.

Side made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/ Classic walnut face and balancing white on other side complete all as specified and directed.

Back made out of plywood 6mm thick BWR Gde.

Upper drawer complete excluding handle.

Lower drawer complete excluding handle.

CP handle 100mm long of approved quality.

S&F PVC/Hard rubber toe of suitable size.

M&L to repair Bed hard (MAP) by replacing the following unserviceable parts with approved ones.Rest all as per drawings and directed by Engr-in-charge. (DRG NO. FD/E6/MAP/08,FD/E6/MAP/08(R )

Plywood 12mm(9 ply) thick BWR Gde.

Nut and bolt of suitable size complete.

Pre-laminated MDFboard(exterior gde) of Head rest complete.

Pre-laminated MDFboard(exterior gde) of foot rest complete.

S & F PVC/Hard rubber toe of suitable size.

M&L to repair Table computer by replcing the following parts with prelaminated exterior gde MDF board OSL (Designation PLMDF-12).Rest all as per the drawings and as directed by Engr-in-charge. (DRG NO.FD/E6/MAP/03,TP)

Top made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Naina teak/Classic walnut face and balancing white on other side duly provided with teak wood beading 4x18mm thick all around of suitable size fixed by panel pin and adhesive with diamond cut pattern finishing at corners complete all as specified and directed.

Side made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side naina teak/Classic walnut face and balancing white on other side completcomplete all as specified and directed.

All as per item no 61.01 but Key board tray complete excluding telescopic channel

All as per item no 61.01but pull out tray complete excluding telescopic channel.

All as per item no 61.01 but drawer complete excluding knob.

All as per item no 61.01 but middle shelf including vertical portion complete.

All as per item no 61.01 but bottom shelf complete.

Telescopic channel of suitable size and approved quality.

Note:- Sample and shade of materials will be determined as per actual requirement at site.

M&L to repair Table dining OR Steel by replacing the top (size 1900mm x 685mm) made out of 18mm thick pre-laminated exterior gde MDF board OSL (Designation PLMDF-12) one side Classic walnut face and balancing white on other side with teakwood beading 4x18mm thick all around of suitable size fixed by panel pins and adhesive with diamond cut pattern finishing at corners and polished with high gloss finish of lacquer polish. Rest all as per the drawing and directed by Engr-in-charge. (DRG NO. FD-165(M) )

Preparation of old surface of Table dining OR Steel by de-rusting the surface and painting with one coat of synthetic enamel paint (Ist quality) black colour complete.Rest all as specified and directed by Engr-in-charge.

S&F PVC/Hard rubber toe of approved quality and suitable size.

Removing of unserviceable plywood from Charpoy plywood top (MAP) (FD/MAP-II/01) and providing 12mm thick (9 ply) plywood BWR Gde with suitable size (1990mm x 910mm) of nut and bolt including welding of loose joints if any, and painting by brush or by spray machine with one coat of Ist quality synthetic enamel paint of approved shade complete.Rest all as per the drawing & directed by Engr-in-charge.

Removing of unserviceable plywood from Charpoy folding (FD-388(R) and providing 8/9mm thick plywood BWR Gde with suitable size of nut and bolt including welding of loose jointsif any, and painting by brush or by spray machine with one coat of Ist quality synthetic enamel paint of approved shade complete.Rest all as per the drawing & directed by Engr-in-charge.

Note:- Net contract sum shall be calculated after deduction of Sch of credit.

SNEH CORPORATION