Construction of Multipurpose Hall at Govt. Degree College Handwara

Amount

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. in Ordinary Rock

Providing and laying of stone soling size (150mm) on level (hand packed) watering ramming complete under raft and flooring. Complete job

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work upto plinth level 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) incl. carriage complete

Providing and laying in position cement concrete of specified grade incl. curring but excluding the cost of centering and shuttering-all work upto plinth level 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40mm nominal size crushed), including carriage. complete

Reinforced cement concrete work in arches, archribs, domes, vaults shells, folded plate and roofs having slope more than 15° upto floor five level level including curing but excluding the cost of centering, shuttering finishing and reinforcement with: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Filling in plinth etc in layers not exceeding 20cm in depth consolidating each layer by ramming, watering complete job.

Available earth filling in trenches

GSB filling under flooring in rooms.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Hot rolled deformed bars

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platforms.

Lintel, beams, plinth beams, girders, bressumers and cantilevers

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600mm)

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete valleys 900mm

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Welded

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in Super Structure upto floor 5 Level and in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) and all carriages complete

15mm Cement plaster on the rough side of single or half brick wall of 1 : 6 ( 1 cement : 6 coarse sand)

12mm Cement plaster of mix 1 : 4 (1 cement : 4 coarse sand)

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc complete 50mm thick with 20mm nominal size stone aggregate

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete In colour such as White, Ivory, Grey, Fume Red Brown

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class kail wood (35 mm thick)

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of First class kail wood (35 mm thick)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws ( 35 mm thick)

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125 mm

Providing and fixing aluminumTower boults ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Single rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per IS : 1868) aluminum lever handles of approved quality with necessary screws etc. complete

Providing and fixing of approved quality 125mm oxidized M.S windows stays with necessary screws etc complete.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600 x 600 mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab upto 0.5 sqm) ( grenite of any colour or shade 16 mm thick)

Providing and fixing of 12mm thick budloo paneling for soffits including cost of 1”x1.5” budloo frame work. complete job

Providing and fixing of 300x400mm 2nd class budloo wood evis boarding paneled on one side complete job

Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately. Pahal Gardan

Providing and fixing of frame system in ceiling which including providing G.I sheet with zinc coating fastened to ceiling soffit using Rawl plug and screw at 600mm centers, with first and last fixing point at not greater than 50mm from either end. Plaster board and finishing:- 1 x 12.5mm gypsum board on internal side is screw is fixed to frame using self tapping 3.5x25mm corrosion resistant drywall screws spaced on all joints and 300mm centers in the field of boards. Board sand screw heads are to be jointed and finished so as to have a flush look which includes filling tapered edge and square edges of board with Easy joint compound, Boral paper Tap (Hall and stage ceiling) complete job

Providing and fixing of 12mm laminated action tesa AC grade IV wooden flooring on stage including cost of backing layer and thin film of polythene floor cover complete.

Providing and fixing of 12mm thick ply in ceiling fixed to wooden frame work above false ceiling in Hall and lobby (Rough ceiling)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing / fixing of G.I/ PVC pipe fittings including required fixtures etc for plumbing & Sanitary incl. all charges complete. (Make of SURIYA PRAKASH & PRINCE)

G.I. Pipe 15mm class-B (SURIYA PRAKASH)

G.I. Pipe 20mm class-B (SURIYA PRAKASH)

PVC pipe 100m dia type-A (PRINCE)

PVC pipe 75m dia type-A (PRINCE)

Providing / fixing of C.P. bath fittings/ other accessories of approved quality including all charges. Make of (JAQUAR OR HIND WARE)

W.C. (Anglo indian)

Washbasin with pedestals.

C.P. wall mixer.

C.P. basin mixer.

C.P. Angle values

C.P. Bibcock.

Electric Geyser 60ltr capacity. (VENUS, JAQUAR, RECOLD)

PVC water storage tank. (SINTEX/ COMFORT)

CP niples of different sizes

CP Connection

P/F water closet squatting pan (Indian type W.C pan) with 100 mm sand cast iron P or S trap. 10ltr low level P.V.C flush cistern, incl flush pipe ( of approved make) with manually controlled device handle lever) confirming to IS:7231, with all fittings and fixtures complete incl. cutting and making good the walls and floors where ever required, vitreous china Orissa pattern W.C pan of size 580 x 440 mm with integral type foot rests

P/F wash basin with C.I brackets , 15mm CP Brass pillars taps, 32 mm CP brass waste of standard pattern , incl. painting of fittings and brackets cutting and making good walls wherever required vitreous china wash basin size 630 x 450 mm with a pair of 15 mm CP brass pillar taps incl. P/F white vitreous china pedestal complete job

quantity may vary +- 25%

M/S MAGRAY CONSTRUCTIONS