CONSTRUCTION OF BUILDING FOR ACCOMMODATING 5KL BULK MILK COOLER AT KULLEGOUNDANUR MPCS

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and refilling the sides,cleaning and leveling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling with M-Sand for basement to required thickness, watered, well rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling with gravel for foundation and basement to required thickness, watered, well rammed and consolidated, etc., completed as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (One Cement, Four M-sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation and flooring the top surface rough to receive the floor including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Brick work in Cement Mortar 1:5 (one part cement and five parts M-sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" to line, level and to plumb on one face including necessary scaffolding, racking out joints, curing etc., complete as directed by the departmental officer and as per standard specification. a)for Foundation and Basementa)

b) for above basement up to 4.50m ht.

Supplying , erection and steel centering for all RCC works using M.S Sheet, M.S. angles casurina props C.W.joints for all type of RCC works (ie) beams, roof slab, lintel, column footing, column & roof beam etc., including necessary supports with all cross bracing, filling the slits and holes the reprieved materials should be taken by the contractor and side shuttering etc., complete as directed by the departmental officers.a) Up to basement - cloumn surface

b) Up to basement - Plain surface

c) above basement level 3.30m height - column surfaces

d) above basement level 3.30m height - Plain surface

e) up to 3.30m to 4.30m height - column surfaces

Reinforced Cement Concrete 1:1-1/2:3 (One Cement, One and a half M-sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers a) for Foundation and Basement

b) Above basement up to 4.50m ht

Supplying, fabricating and placing in position of reinforcement, grills for all RCC works including cost of steel and binding wire , cutting and tying etc., complete as directed by the departmental officers.RTS rods in all floors

Plain Cement Concrete 1:2:4 (one cement, two M-sand and four hard broken stone jelly) using 20mm jelly for the machinery bed, flooring and other bed blocks works and flooring including curing (excluding centering) etc., complete as per standard specifications and as directed by the departmental officers.

Providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 (One Cement, Two M-sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of cuddapah slab 50mm thick including cutting and polishing on one side etc.,complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best quality Cuddapah sink of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and laying of unpolished (on both side) machine cut modikuppam Paradise granite stone slab of size 600x450 laid over a cement mortar 1:3 (One cement and three m-sand)-20mm thick including conveyance, cutting, laying, curing and pointing the joints with white cement mixed with matching colouring pigments etc., complete as directed by departmental officers..a)30mm thick

b)50mm thick

Paving the flooring with ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M-Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.

Paving the floor with best quality Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-sand) 10mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.

Dadooing walls with printed design colour glazed tiles of size 300mm x 200mm x 6mm laid in Cement Mortar 1:2 (One Cement and Two M-sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. (Required shape and design) etc.,

Supplying and fixing of steel rolling shutter (Gear operated type) with ISI make of approved quality with MS lathes 75mm wide and 18 gauge GI sheet thick to a different sizes including all accessories like sliding groves, shafts, springs, bearings, hood and locking arrangements and grouting the side and top assembly with walls and beams etc. complete and as directed by the departmental officers.

Fabricating, Supplying and fixing in position of steel sheeted windows with the following specifications.Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffeners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly etc complete as directed by the departmental officers.

Manufacturing, supplying and fixing of steel doors with the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel in the shutter and welded intact for 1/3 bottom portion of the shutter. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat sandwitching the CR sheet in between. Additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 20kg/sq.m and 6 Nos hinges for double leaves shutter to be provided 6nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door. Tower bolts 2nos. one at top and the other at the bottom arte provided one aldrop is provided at on appropriate place in the door. A Tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all meterials, labour charges, taxes, transportation to site of work, loading, unloading and all other incidental charges etc., complete.

Supplying and fixing in position of mild steel grills for following size square rod and cutting, welding including priming coat etc complete as directed by the departmental officers.

Supplying and fixing of steel weld mesh Partition using 40x40x6mm mild steel L / T angle and 75x25-10G welded mesh & Mild steel flat 30x6mm as directed by the departmental officers with necessary of sizes including cutting, welding and labour charges etc., complete as directed by the departmental officers.

Supplying and fixing of steel weld mesh Gate using 40x40x6mm mild steel L / T angle and 75x25-10G welded mesh & Mild steel flat 30x6mm as directed by the departmental officers with necessary of sizes including cutting, welding ,locking arrangements and labour charges etc., complete as directed by the departmental officers.

Manufacturing, supplying and fixing in positon of RCC Jally of 5cm thick in cement concrete 1:2:4 using 20mm machine crushed stone jelly (excluding cost of reinforcement steel) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed

fabricating, Supplying and fixing in position of mild steel (RHS) Rectangular steel hollow section following thickness and M.S channel sizes of 150mmx75mmX5.7mm thickness for loading dock area including cutting, welding and fixing in purlin etc., completed as directed by the departmental officers.

Supplying and fixing in position of Powder coated galvalume colour sheet of 0.47mm thickness with necessary bolts, nuts and washers, metal screws etc. complete with standard specification and as directed by the departmental officers.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as directed by the departmental officers with standard specifications.

Special ceiling plastering Cement Mortar 1:3 (One Cement and Three P- Sand) 12mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick in all floors including curing and scaffolding etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint (interior) of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint (exterior) of first class quality and of approved colour over one coat of priming coat including scaffolding charges etc., complete complying with standard specification and as directed by the departmental officers.

Painting two coats of new iron work using ready mixed synthetic enamel paint of approved quality and colour over a priming coat etc. complete as directed by the departmental officers. (such as steel window, Grill , M.S Channel & rolling shutter ets.,)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.a) 110mm dia PVC Pipe

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications.a) 25mm dia PVC Pipe

b) 20mm dia PVC Pipe

Supplying and fixing in position first quality and approved varity with ISI mark PVC specials and Brass ball valve etc.,a) 25mm dia Coupler

b) 25mm dia Tee.

c) 25mm dia Elbow

d) 20mm dia Coupler

e) 20mm dia Elbow.

f) 20mm dia Tee.

g) 25x20 Reducer

h) 20mm dia UPVC Ball valve

i) 25mm dia UPVC Ball valve

Supplying and fixing in position first quality and approved varity with ISI mark PVC specials and Brass ball valve etc.,a) 75mm dia PVC Pipe

b) 110mm dia PVC Pipe

Supplying and fixing in position of the following PVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc., including fixing to walls with necessary teak wood plugs screws etc., and giving connections to the PVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc., complete complying with standard specifications- standard specifications.a) 75MM dia PVC Elbow

b) 110MM dia PVC Elbow

c) 110mm dia PVC door Elbow

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.....

Supplying and fixing position PVC Nahani Trap / Floor Trap of the following sizes with best PVC gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M-sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification.

Supplying and fixing best quality and make of ready mixed HDPE water storage Water tank having 1000 litres capacity -made of PVC materials- including necessary provision for conveying, jointing delivery line, scour pipe, over flow pipe etc., and lifting the tank to the top of the building placing in position etc., complete as directed by the departmental officers.

Manufacturing, Supplying & fixing of Round RCC Precast Rings of 1200mm dia Height of 305mm and thickness 32/40mm including material with transport charges & labour charges etc, completed as directed by the departmental officers.

Geological survey charges for divining water points for drilling the bore wells including helpers, transport charges etc., completed

Supplying and fixing in position of the following PVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc., including fixing to walls with necessary teak wood plugs screws etc., and giving connections to the PVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc., complete complying with standard specifications- standard specifications.a) For the depth from 0 to 60m

b) For the depth from 61 to 90m

c) For the depth from 91 to 120m

d) For the depth from 121 to 150m

e) For the depth from 151 to 180m

f) For the depth from 181 to 210m

g) For the depth from 211 to 240m

h) For the depth from 241 to 270m

Supplying suitable PVC casing pipe for 6" dia borewell best approved quality with ISI mark with necessary PVC coupling etc., (The PVC pipe should be got approved by departmental officer before execution)

Labour charges for PVC pipe

Supplying and fixing of suitable PVC end cap (6kg/cm2) for 6" dia bore well of best quality with ISI mark (The PVC end cap should be got approved by departmental officer before execution).

Supplying of best approved quality of UPVC Pipe used for commercial applications operate and higher water pressure (Schedule-80) for 32mm dia 10Kg/cm2 as one piece without join with homogeneous section through out the length and with marking every 5m, for erection in the borewell etc., completed as directed by the federation officers

Supplying, laying and jointing HDPE pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives etc for below ground levela) 32mm dia HDPE Pipe

Supplying of 3.0HP submersible motor cum Pump set of any ISI certified company and sump motor 1.0 HP Monoblock Pump including all accessories etc.,completeda) 3.0HP submersible motor cum Pump set

b) Sump motor 1.0 HP Monoblock Pump

Supply of Panel box of size 2'9'' x 2'9'' made with MS plats of 16gauge sheets with 15mm plywood board on the inner back and with openable shutter on the front for fixing EB electric water hour meter, main board and for fixing the pannel board suitable strong painted with enamel painint powder coated as directed by the departmental officers.

Supply of 3Phase Panel board including labour chargers, containing starter for 3HP for submergible motor,amp,meter,volt meter.one number MCB, indictor and ets., fitted on powder coated MS Sheet of 18gauge with full wiring as directed by the departmental officers.

Supply & run off 2 of 4 Sq.mm under ground cable suitable for inserting inside water storage of bore well with perfect water seal and high resistant to heat with copper conductor insulation of 4 Sq.mm cross section for 440 volt and 15 Ams current capacity as directed by the departmental officers.

Supply of Nylon rope for bore -well of 14mm dia strong and not decayable for the errection of holding the total weight of the submergible motor as directed by the departmental officers.

Labour charges for erecting the submersible motor with UG flat cable, nylon rope and 32mm HDPE house tubes attached with pump in the vertical bore, fixing the hoses firmly in the bore by attaching to the clamps and connecting the hoses to the PVC lines with hose coller and etc.,as directed by the departmental officers.

Supplying and fixing of 40mm dia cast iron Non-Return valve conforming to IS & swing type with natural rubber flap, flanges set etc., as directed by the departmental officers.

Supply and fixing of TNEB meter board suitable for 63A three phase service connection with 63A fuse unit (500V) 63A neutral link and earth link (1'' x 1/8'' Copper flat) on TW plank of size 375mmx300mmx19mm with supporting T.W reepers of 1'' thick on either side with painting with suitable bolt and nuts for fixing the TW plank on wall earth connection and inter connection with 7/20 PVC insulated copper wire from EB neter to fuse unit (SD 127)

Supplying a the following dia G.I Specials confirming to IS 1239 a) 40mm GI Coupling

b) 40mm GI bend

c) 40mm GI clamp set

Supply and run off SWG copper wire on walls or below ground level with necessary U nails earthwork excavation and refilling cost of all materials etc complete in all respects-1M

Earthing as per the ISI specification with an earth electrode of 2.1mt Class'B' Cllass GI Pipe of dia less than 40mm with copper arth flat of size 125mmc50ccx6mm with necessary funneling arrangements using charcoal, common salt,GI reducer,check nuts etc., with necessary masonary work and with 38mm thick RCC Cover slab for the brick masonary inculding cost of moulding steel,fabrication etc., complete respects.

Supplying and fixing of 63Amp DPIC switch of 500V with Face & Neutrual (side handle) on suitable T.W board of size 30cmx20cm x7.5cm including necessary internal connection & earth connection etc., complete.

Construction of Borewell chamber of clear size 0.60 m x 0.60 m x 0.60 m including refilling testing etc., completed

Providing internal 3 phase Electrical wiring including all from EB pole to BMC building with all fittings (wire,switches., etc) as per the tender specification.

GST (Note: The tenderer should quote the amount towards Goods and Service tax (GST) in the appropriate columns in terms of percentage (%). If not quoted, it will be considered that the rate quoted is inclusive of GST.)

Please Enable Macros to View BoQ information