Fixation of rates for Supply, Installation, testing and commissioning of Fire fighting fixture

Amount

FIRE PUMP AND ACCESSORIES

Supply, installation, testing & commissioning of Centrifugal Pump set (End suction back pull out). The capacity of pump, Total Head-70.00m, Discharge-2850 lpm, (a minimum pressure of 3.5 kg/cm2 at top most hydrant) with 3-phase 50Hz, TEFC induction motor coupled with a common base (duly factory assembly) with electrical control panel suitable for the pump set , including construction of concrete foundation, suction & delivery piping arrangements, fixing of required sizes & nos.of D.I. valves (pressure ratting PN-1.6) like Sluice valves, Butterfly valves, NR valves & flanged end foot valve with strainer etc. all complete as per the specification & direction of EIC. As per technical specification. Make: KIRLOSKAR/ WILO MATHER + PLATT/ GRUNDFOS.

Main fire pump set.

Supply, installation, testing & commissioning of Centrifugal Pump set (End suction back pull out). The capacity of pump, Total Head-70.00m, Discharge-180 lpm with 3-phase 50Hz, TEFC induction motor coupled with a common base (duly factory assembly) with electrical control panel suitable for the pump, including construction of concrete foundation, suction & delivery piping arrangements, fixing of required sizes & nos.of D.I. valves (pressure ratting PN-1.6) like Sluice valves, Butterfly valves, NR valves & flanged end foot valve with strainer etc. all complete as per the specification & direction of EIC. As per technical specification. Make: KIRLOSKAR/ WILO MATHER+PLATT/ GRUNDFOS

Jockey pump set.

Supply, installation, testing & commissioning of Centrifugal Pump set (End suction back pull out). The capacity of pump, Total Head-70.00m, Discharge-2850 lpm with suitable capacity of RC cooled Diesel engine coupled with a common base (duly factory assembly) with auto control panel, battery, battery charger & fuel tank of capacity 200 ltr. (self start mechanism) suitable for the pump, including construction of concrete foundation, vibration pad, suction & delivery piping arrangements, fixing of required sizes & nos.of D.I. valves (pressure ratting PN-1.6) like Sluice valves, Butterfly valves, NR valves & flanged end foot valve with strainer etc. all complete as per the specification & direction of EIC. As per technical specification. Make: KIRLOSKAR/ WILO MATHER + PLATT/ GRUNDFOS

Diesel Engine Pump set. (standby)

Supply, installation, testing & commissioning of air cushion vessel made out of G.I. / M.S. 'C' class heavy duty pipes having adequate to reduce water pressure, drain & to accommodate with pressure gauge & switch suitable for the system etc. all complete as per the specification & direction of EIC.

Size-250mm dia x1.80m ht.

FIRE HYDRANT & WET RISER SYSTEM

Providing all materials, labour, T&P for laying of following dia M.S. heavy class pipes conforming to IS:1239/IS:3589 with ISI mark & required sizes of fitting like off set, bend, tee, reducer flange & flange joints etc. as per site condition including gas cutting by oxygen and acetelene gas flame, fitting and setting as per required size wherever necessary, jointing the pipes by electric welding confirming to IS specification and electrodes confirming to IS specification after 'V' grove cutting. Aligning the pipes inside the trenches including necessary excavation of earth work of required width & depth in all kinds of soil /rock and back filling or supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fasteners) or angle iron, G.I. pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per the approved specification including cutting holes and chases in brick/RCC wall/roof/chajja and making good the same to original condition.

All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included. Painting 2 (two) or more coats with synthetic enamel paint of Post office red shade over a coat of primer for above ground level & painting 2 (two) or more coats with anticorrosive epoxy paint for below ground level. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approved specification including testing & commissioning the system.The cost inclusive of hire and running charges of welding generator set & all taxes, duties, transportation, hire & running charges of machineries, POL, to & fro charges with all consumables for all floors etc. all complete as per specification & direction of EIC. Make-SAIL/ JINDAL/ TATA

150mm dia (Heavy class) as per IS-1239 Part-I/2004

80mm dia (Heavy class) as per IS-1239(Part-I)/2004

65mm dia (Heavy class) as per IS-1239(Part-I)/2004

Providing, fitting & fixing of Stainless Steel fire hydrant landing valve with 80mm NB flanged inlet (Table-E Flange), SS spindle controlled 63mm dia female instantaneous outlet type. SS coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS-5290 with ISI mark. Including flange joint & tapping from wet rise & testing and commissioning the system for all floors etc. all complete as per approved specification & direction of EIC. Make-KARTAR/ NEWAGE/ OMEX

Single Landing Valve (oblique type)

Providing, fitting & fixing of following size Ductile Iron double flanged slim seal wafer type Butterfly valves with EPDM rubber lined with lever operated as per IS-13095 with ISI mark of pressure ratting PN-1.60 including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure etc. all complete as per specification & direction of E.I.C. Make-KIRLOSKAR/ VAG/ AUDCO

150mm dia

Providing, fitting and fixing of first aid fire hose reel wall mounting swinging type fitted with 20mm dia 30.00 m long high pressure (10Kg/cm2) themo plastic hose tube conforming to IS: 12585 with ISI mark Type II with 5mm outlet stainless steel/ Brass nozzle with shut off valve confirming to IS 884-1969 with ISI mark including testing & commissioning the system for all floors etc. all complete all complete as per apporved specification & direction of EIC. Make-MITRAS/ NEWAGE/ MINIMAX/ LIFEGUARD

Providing, fitting & fixing of Non-percolating flexible hose (RRL type-'B' with EPDM Lined) confirming to IS:636 with ISI mark (63 mm dia x 15 M long) complete with instantaneous type stainless steel male and female couplings confirming to IS:903 with ISI mark wounded & riveted to hose pipe with 18 SWG stainless steel wire including testing & commissioning the system for all floors etc. all complete as per approved specification & direction of EIC. Make-KARTAR/ MITRAS/ NEWAGE/ LIFEGUARD.

Providing, fitting and fixing of 63 mm dia stainless steel instantaneous male inlet pattern branch short pipe conforming to IS:903 with ISI mark suitable for interconnection to hose pipe coupling including testing & commissioning the system for all floors etc. all complete as per approved specification & direction of EIC. Make-KARTAR/ NEWAGE/ OMEX

Providing, fitting & fixing of GM fire brigade connection consisting of 63 mm dia instantaneous type male couplings with built-in check valves, 150mm dia flanged outlet complete with bolts, nuts and rubber insertions confirming to IS:904 with ISI mark including testing & commissioning the system etc. all complete as per apporoved specification & direction of EIC. Make-MITRAS/ NEWAGE/ MINIMAX/ GETECH

Providing, fitting and fixing of D.I. single air relief valve with stop cock confirming to IS:14845/2000 with ISI mark for water works purpose including fixing the same with hydrant riser including testing & commissioning the system etc. all complete as per approved specification & direction of EIC. Make-KIRLOSKAR/ IVC/ ZOLOTO

25 mm C.I. single Air Relief Valve

Providing, fitting and fixing of dial type stainless steel pressure gauge duly calibrated with isolation ball valve and short piece etc. fixed at hydrant station including testing & commissioning the system etc. all complete as per approved specification & direction of EIC. Make- ELSTER/ H-GURU.

Dialmeter of 150mm dia of pressure rating 0-15 kg/cm2.

Providing, fitting & fixing of following size Ductile Iron double flanged Y type strainer with SS 304 perforated screen confirming to IS 1538 with ISI mark of pressure rating PN-1.60 including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure & all complete as per specification & direction of EIC. Make-KIRLOSKAR/ IVC/ ZOLOTO/ VENUS/ HONEYWELL

150mm dia

Providing, fitting and fixing of MS/ GI partly glazed single/double hung lockable shutter fabricated from MS/GI section as required with 5mm thick glass for fire station complete including stove enamelled painting of door and frame and words "Fire Hydrant" written on glass, suitable to accommodate 2 (two) RRL ,15m long 63 mm dia hose (RRL),1(One)-branch pipe including suitably mounted on a raised masonry/ vertical MS platform of size 0.6mx0.5mx0.25m (external type with rain cap) including testing & commissioning the system for all floors etc. all complete as per approved specification & direction of EIC. Make-OMEX/ GETECH/ LIFEGUARD

SPRINKLER SYSTEM

Supply,Installation,Testing & Commissioning of Pendent / Upright type Standrd Sprinkler with QB of 68 /79 deg. C temperature rating and 1/2" end connection confirming to IS: 15105 with ISI mark for all floors etc. all complete as per direction of Engineer-in-charge. Make-TYCO/ LEADER/ DSS/ HD

Supply,Installation,Testing & Commissioning 150NB Alarm Valve, C/w Sprinkler Water Motor Gong Retarded Chamber, Flange to:- ANSI B 16. 1 Class 125/ANSI B16.5 Class 100, All Components are UL Listed/FM Approved , Rated pressure 17.50 kg/cm2, Test pressure 500PSI confirming to IS :15105:2002 with ISI mark as per direction of Engineer-in-charge. Make-TYCO/ LEADER/ DSS/ HD/ NEWAGE

Providing, fitting & fixing of following size Ductile Iron double flanged Y type strainer with SS 304 perforated screen confirming to IS 1538 with ISI mark of pressure rating PN-1.60 including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure & all complete as per specification & direction of E.I.C. Make- KIRLOSKAR/ IVC/ ZOLOTO/ VENUS/ HONEYWELL

150mm dia

Providing all materials, labour, T&P for laying of following dia M.S. heavy class pipes conforming to IS:1239/IS:3589 with ISI mark & required sizes of fitting like off set, bend, tee, reducer, flange & flange joints etc. as per site condition including gas cutting by oxygen and acetelene gas flame, fitting and setting as per required size wherever necessary, jointing the pipes by electric welding confirming to IS specification and electrodes confirming to IS specification after 'V' grove cutting. Aligning the pipes inside the trenches including necessary excavation of earth work of required width & depth in all kinds of soil /rock and back filling or supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fasteners) or angle iron, G.I. pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealent compound at either end all as per the approved specification including cutting holes and chases in brick/RCC wall/roof/chajja and making good the same to original condition.

All hangers, clamps, brackets etc. shall be of galvanized iron unless specified otherwise and then supply of the same shall also be included. Painting 2 (two) or more coats with synthetic enamel paint of Post office red shade over a coat of primer for above ground level & painting 2 (two) or more coats with anticorrosive epoxy paint for below ground level. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approved specification including testing & commissioning the system.The cost inclusive of hire and running charges of welding generator set & all taxes, duties, transportation, hire & running charges of machineries, POL, to & fro charges with all consumables for all floors etc. all complete as per specification & direction of EIC. Make-SAIL/ JINDAL/ TATA

150mm dia (Heavy class) as per IS-1239 Part-I/ 2004

100mm dia (Heavy class) as per IS-1239(Part-I)/ 2004

80mm dia (Heavy class) as per IS-1239(Part-I)/ 2004

65mm dia (Heavy class) as per IS-1239(Part-I)/ 2004

50mm NB (Heavy class) as per IS-1239(Part-I)/ 2004

40mm NB (Heavy class) as per IS-1239(Part-I)/ 2004

32mm NB (Heavy class) as per IS-1239(Part-I)/ 2004

25mm NB (Heavy class) as per IS-1239(Part-I)/ 2004

Providing, fitting & fixing of following size Ductile Iron double flanged slim seal wafer type Butterfly valves with EPDM rubber lined with lever operated as per IS-13095 with ISI mark of pressure ratting PN-1.60 including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure for all floors etc. all complete as per specification & direction of E.I.C. Make-KIRLOSKAR/ VAG/ AUDCO

Providing, fitting & fixing of following size Ductile Iron double flanged type Non return Valve as per IS- 5312 (Part 1): 2004 with ISI mark of pressure ratting PN-1.60 including fixing the same with supply of required jointing materials like flanges, rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure for all floors etc. all complete as per specification & direction of E.I.C. Make- KIRLOSKAR/ VAG/ AUDCO

Providing, fitting & fixing of following size Gunmetal flanged type Globe Valve with CI hand wheel Confirming to IS -13114 : 1991 with ISI mark of pressure ratting PN-1.60 including fixing the same with supply of required jointing materials like flanges, rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure for all floors etc. all complete as per specification & direction of E.I.C. Make-KIRLOSKAR/ IVC/ ZOLOTO/ VENUS

Supply,Installation,Testing & Commissioning of D. I. Sight glass with 25 NB Gunmetal Globe Valve with CI hand wheel ISI Mark for all floors etc. all complete as per direction of Engineer-in-charge. Make-KIRLOSKAR/ IVC/ ZOLOTO/ VENUS

Providing, fitting and fixing of D.I. single Air relief valve with stop cock confirming to IS:14845/2000 with ISI mark for water works purpose including fixing the same with hydrant riser including testing & commissioning the system etc. all complete as per approved specification & direction of EIC. Make-KIRLOSKAR/ IVC/ ZOLOTO/ KARTAR

Providing & fixing of Water Flow Switch 150 mm Diameter with all accessories for all floors etc. all complete as per direction of Engineer-in-charge. Make-HONEYWELL/ POTTER/ AQUAPRO

Providing & fixing of 25 mm size Gunmetal Pressure Release Valve with isolation valve and all accessories conforming to IS3233:1965 as per direction of Engineer-in-charge. Make-KIRLOSKAR/ IVC/ ZOLOTO/ KARTAR/ SKS

Providing & fixing of Flexible Sprinkler Hose Corrugated Unbraided type of size 1000 mm for Fire Sprinklers, with 1'' Inlet Nipple BSPT,1/2" Outlet Reducer BSPT,0.7 m Square Supports Bar & Brackets(UL Listed) with all complete accessories as per direction of Engineer-in-charge. Make- NEWAGE/ MINIMAX/ SUPEREX

EXTINGUISHER SYSTEM

Supplying, installation, testing and commissioning of CO2 type Fire Extinguisher 4.5 kg capacity confirming to IS: 2878 made from ISI marked seamless cylinder confirming to IS: 7285, fitted with ISI marked controlled valve confirming to IS: 3224, high pressure 1mtr discharge hose & horn complete with initial gas charged with carrying handle & wall mounting bracket for all floors & service building etc. as per direction of Engineer-in-charge. Make-MINIMAX/ CEASEFIRE/ SAFEX/ SAFEFIRE/ OMEX

Supplying installation testing and commissioning of ABC type fire extinguishers of 6 kg capacity confirming to IS:14609 including cost of all material & labour for all floors & service building etc. all complete. Make-MINIMAX/ CEASEFIRE/ SAFEX/ SAFEFIRE/ SAIEX

Supplying installation testing and commissioning of Mechanical Foam type 9 litre capacity Fire Extinguisher, ISI marked, IS: 10204, containing 540 ml AFFF liquid ISI marked, IS: 4989 Part II and a polyurethane coated CO2 Gas Cartridge, ISI marked, IS: 4947 complete with gunmetal union cap, nylon hose with plastic foam making branch and wall mounting bracket for all floors & service building etc. all complete as per direction of Engineer-incharge. Make-MINIMAX/ CEASEFIRE/ SAFEX/ SAFEFIRE/ LIFEGUARD

AUTOMATIC FIRE ALARMING AND DETECTION SYSTEM (Make In India Product will be prefered)

Supplying installation testing and commissioning of Microprocessor based Addressable UL listed Fire Alarm Control Panel (12 loop or combination of indivisual 4 loops ) suitable for serving the followingg detectors & Devices in maximum with LCD display all complete) 2 Nos 12 Volt 40 Ah SMF battery, Battery backup , more than 1500 event storage facility with real time clock,Earth fault annuncing facility, double adress sensing, Minimum 200 devices per loop,Low battery warning with audiovisual indication etc. as per direction of Engineer-incharge. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL/SIEMENS (UL approved)

Supplying installation testing and commissioning of Addressable Photoelectric type Smoke Detector, complete with base and accessories for Above False Ceiling for all floors etc. as per direction of Engineer-in-charge. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL.(UL approved)

Supplying installation testing and commissioning of Addressable Heat Detector, complete with base and accessories for all floors etc. as per direction of Engineer-in-charge. Make- HONEYWELL/ RAVEL/ BOSCH/ EDWARD (UL approved)

Supplying installation testing and commissioning of Relay control Module complete for all floors etc. as per the direction of Engineer-in-charge.Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL.(UL approved)

Providing & fixing of Isolator Module with Base complete for all floors etc. as per the direction of Engineer-in-charge. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL.(UL approved)

Supplying installation testing and commissioning of Addressable Manual Pull Station, complete with addressable mini input module, back box and accessories for all floors etc. as per direction of Engineer-in-charge. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL.(UL approved)

Supplying installation testing and commissioning of Audio Visual Strobe, complete with mounting box and accessories and module if require for all floors etc. as per direction of Engineer-incharge. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL.(UL approved)

Supplying, installing, testing and commissioning of Hooter Cum Strobe at 85 DB @ 3m for Audible annunciation and 75cd flashing at 1 Hz for visual indication. With Control Module. The Hooter cum Strobe with Control Module shall be flush or surface mountable type with all accessories etc., complete and as per technical specification. The devices shall be of EN and LPCP listed for all floors etc. Make- HONEYWELL/ BOSCH/ EDWARD/ RAVEL(UL approved)

Providing and laying of a pair of 1.5 sq.mm single core flexible copper cable (2X 1.5) to be laid within Existing PVC conduit of suitable size to be erected above the wall or concealed, as the case may be, with all accessories for all floors etc. as per direction of Engineer-in-charge. Make- POLYCAB/ HAVELLS/ RR KABLE

AUTOMATIC FIRE DETECTION SUPPRESSION SYSTEM FOR ELECTRIC PANEL

Supply,installation, testing & commissioning of 5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation. Make: SUPREMEX/ FIREBOY/ AMEREX

Supply,installation, testing & commissioning of Linear pneumatic heat Detection Tube (size: 6 mm Outer Dia & 4mm inner dia) with all necessary fittings & supports. Make: SUPREMEX/ FIREBOY/ AMEREX

Supply,installation, testing & commissioning of Master Control Unit with Audio Visual Alarm With Wiring to Make Complete System Operational. The Control Panel Should have Provision for integration with Fire Alarm/ SCADA/ BMS System. Make: SUPREMEX/ FIREBOY/ AMEREX

Supply fitting & fixing of LED EXIT Light fitting of both side signage with built in battery back-up for 2 hrs with proper wiring with MS conduiting from the existing power sources for all floors as per approved specification etc.all complete as per direction of EIC. Make:- BAJAJ (CAT No : BESL O3 LED SSD WBB Green) / Equivalent of Crompton/ Wipro/ Philips/ Havells.

N.B:- 1. The above figures of expected requirement are indicative only. IDCO doesn’t guarantee any minimum business / volume in this tender enquiry. 2. Rates quoted shall be excluding the GST rates as applicable for Dist.-Khurda, Odisha.

CYMK INDUSTRIES PRIVATE LIMITED