GE (N) P/TOKEN - 01 OF 2024-2025 SPECIAL REPAIR TO BLDG NO 5 (SQUASH COURT), SPECIAL REPAIR TO ELECTRICAL WIRING AT BUILDING NO 7 NEHRU MARG AND MW WORKS IN THE AREA OF AGE B/R (EAST) AND AGE E/M (NORTH) UNDER GE (NORTH) PUNE

Amount

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as speified and directed

M&L for Pre-cast cement concrete block masonry with solid blocks 1:3:6, type C-1, exc 10cm in width and setting in mortar in CM 1:6 complete all as speified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed

S&F for Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as speified and directed

Dismantling of asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws with two corrugation side lap complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc in any height of Bldg complete all as speified and directed

M&L for 15mm thick rendering in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement with two coats of exterior emulsion weather proof paint over a coat of primer including preparation of new surface complete all as speified and directed

M&L for rendering 15 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) finished even and fair without using extra cement and two coats of OBD of any tint over a coat of primer in any height of Bldg complete all as speified and directed

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.09 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including 20mm thick screed bed or bedding layer in CM 1:6 incl dismantling of existing tiles complete all as speified and directed

M&L for glazed ceramic coloured tiles of size 450x300x7-8mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick backing coat in CM1:4 incl dismantling of existing tiles complete all as speified and directed

M&L for coloured, textured design heavy duty exterior tiles of size 300mm x 300mm x10 mm thick as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and shade/ pattern as approved by GE over and including 15mm thick screed bed in CM (1:4) and demolition of existing tiles of any description complete all as specified and as directed. Make: Johnson Endura textured design or equivalent as approved by GE.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all including taking down existing G I tubing complete all as specified and as directed

-Ditto- all as per Srl item No 14 here-in-before, but fixing only complete all as specified and as directed

S&F for 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc all including taking down existing G I tubing complete all as specified and as directed

All as per Srl item No 16 here-in-before, but fixing only

M&L for cutting chases pinning in brick work for concealing water tubing and making good to facing where required and pointing in cement motar 1:3, cutting n.exc. 10cm girth complete all as specified and as directed

S&F in repair 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float ovel handle including brackets and PVC flushing pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and as directed

S&F in repair PVC connection 15mm bore size with PTMT nuts and washers of length 450mm complete all as specified and as directed

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) ETWC white, including trap, connection to drain (outgoing pipe) and to flushing pipe, antisyphonage pipe, PVC jet for Pedestal pattern pan including 450/600mm long PVC connection and plastic water closet seat of white in colour, back closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed

S&F in repair vitreous china wash hand basin white of bowl size 550 x 440mm incl CP brass waste coupling and PVC waste pipe, 32mm dia, pillar tap cast copper alloy with capstan heads chromium plated fancy 15 mm bore to be fixed with and incl M S brackets complete all as specified and as directed

S&F in repair vitreous china Urinal, Half stall type, white including brass CP 32mm waste pipe and CP brass spreader for fixing with 15 mm dia pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and incl 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe complete all as specified and as directed

S&F in repair 32mm dia PVC waste pipe for WHB/kitchen sink of length 1.0m incl fixing the same complete all as specified and directed

S&F in repair 15 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed complete all as specified and as directed

S&F in repairs hand shower (health faucet) of cast copper alloy chromium plated with 8mm dia, 1.2m long flexible tube and wall hook complete all as specified and as directed

S & F in repair brass chromium plated soap dish , fixed to wall with CP brass screws,complete all as specified and as directed

S & F in repair Brass Chromium plated towel rail complete all as speified and directed. Make: Johnson Fusion series Cat part No: T1350C or of equivalent make as per Appx 'A' as approved by GE

S&F in repair brass chromium plated towel ring complete all as speified and directed. Make: Johnson Fusion series Cat part No: T1351C or of equivalent make as per Appx 'A' as approved by GE

S&F in repairs bib cock long nose quarter turn suitable for 15mm bore pipe long body with flange fancy type brass CP with, screwed for iron pipe or brass ferrule complete all as speified and directed. Johnson VIVA new series Cat part No: T4806C or of equivalent make as per Appx 'A' as approved by GE

S&F in repairs pillar taps swan neck suitable for 15mm bore pipe long body fancy type brass CP with capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified. Make : Johnson Magna series Cat part No: T2804C or of equivalent make as per Appx 'A' as approved by GE.

S&F in repair angle cock with flange quarter turn chromium plated cast copper alloy ISI marked, high pressure screwed down complete all as speified and directed. Make: Johnson Eco Cat part No: T3910C or of equivalent

S&F in repairs two way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as speified and directed. Make Johnson VIVA new series Cat part No: T4808C or of equivalent make as per Appx 'A' as approved by GE.

S&F in repair cast copper alloy CP shower arm square 230mm long with wall flange complete all as specified and directed by Engr-in-charge. Make : Johnson Cat Part No S0001C1 or equivalent of Makes as per Appx A as approved by GE

S&F in repair brass chromium plated shower rose 115mm size square (without arm) with swivel joints, fixing to steel pipe or union complete all as speified and directed. Make Johnson Cat Part No S0006C or equivalent of Makes as per Appx A as approved by GE

S&F in repair vitreous china Urinal, Half stall type, white including waste pipe and CP brass spreader for fixing with 15 mm dia pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and incl 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe complete all as speified and directed.

S&F in repirs wall mixer 2 in 1, quarter turn with provision for over head shower with bend pipe on upper side connecting legs and wall Flanges brass chromium plated suitable for fixing with GI pipes 15mm dia complete all as specified and as directed. Make: Johnson Cat Part No T4821C VIVA series or equivalent of Makes as per Appx A as approved by GE

S&F in repair Toilet paper holder of stainless steel, all as specified and directed. Make: Johnson Fusion series Cat part No: T3254C or equivalent

S&F in repair grating round 100mm size of steel CP with/without hole complete all as speified and directed

Taking down chowkats or frames not exc. 1.5 sq. m each with shutters of any description (without taking off shutters from the frames) complete all as specified and directed

All as per srl item No.41 above but exc. 1.5 sq.m but n exc 4 sqm each complete all as specified and directed

Taking down shutters of any description not exc. 1.5 sq. m each complete all as specified and directed

All as per srl item No. 43 above but exc. 1 sq. m but n exc 2 sqm each complete all as specified and directed

S&F in repair aluminium anodised powder coated ventilator using rectangular tube of size 63.50 x 25 x 1.50 mm including 3.50 mm thick designer glass louvers and stainless steel wire mesh 0.36 mm nominal dia of wire, average width of aperture 1.40 mm using ‘Jindal” aluminium section complete all as specified and directed.

S&F in repair for aluminium powder coated three track sliding window with two glazed shutters with 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make complete all as specified and directed. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

M&L for Powder coating anodised aluminium frame for doors,windows, ventilators with one or morerebates (Min thickness of powder coating 50micron) including joining cleat for fixing etc. complete all as speified and directed

S&F for powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m (Minimum thickness of powder coating 50micron) including 5.5mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each panes with necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, locking system, hinges, anodised aluminum snap beading screws etc. complete all as speified and directed

S&F in repair aluminium die cast body Door closer hydraulically regulated designation No 2, universal type suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60kg ISI Marked complete all as speified and directed

S&F Factory made 100 % solid wood plastic composite(WPC) door frame, single rebate 90 mm x 45 mm made from wood plastic composite (Single extruded process) material with density 780 Kg/ Cum and complete all as specified and directed.NOTE: During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

S&F for 35mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35X6mm all around the shutters including two coat of synthetic enamal paint over one coat of pink primer complete all as specified and directed.

S&F in 100mm butt hinges med weight cold rolled mild steel fixed with chowkats complete all as specified and directed

S&F 250mm long anodised aluminum sliding door bolts with hasp and staple(bolt type) and fixing clip sheet cast or extruded sections and fixing bolts and sliding bolts complete all as specified.

S&F 125mm long aluminum anodised barrel tower bolts of extruded section and fixed with door complete all as specifed and directed.

S&F 125mm long aluminum handles, fabricated type anodised and fixed with door complete all as specifed and directed.

FRONT WALL-ASB SYSTEM 40 WSF : M&L for Panel wall of 18mm thick to be installed directly on the existing wall with screw by creating cavity of 20-22mm bretween the Bldg and panel wall and it is to be completely filled with the fire dried sans and playing surfaces is to be finished with the fillers and paint with one coat of primer and 2 coat of paint. The total construction thickness should be of 40mm, The wall panel is WSF(World Squash Federation) approved. Make:ASB, Germany or equivalent make as per Sports Authority of India approved by GE

M&L for preparation of old plastered or unplastered surfaces of wall/ceiling in any description and any height of Bldg incl cornices, pillasters by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloresce salts and trading oil and greasy spots and applying two coats of Squash court wall/ceiling paint (White & Red WB:147) including filling cracks with wall care putty over Squash court surface primer (WB:1030) or equivalent make as approved by GE complete all as specified and directed.

M&L for preparation of old plastered of ceiling in any description and any height of Bldg incl cornices, pillasters by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloresce salts and trading oil and greasy spots and applying one coat of oil bound distemper including filling cracks with wall putty complete all as specified and directed.

M&L for preparation of old treated steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enemel paint complete all as specified and directed by Engr-in-Charge

M&L for preparation of old treated wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enemel paint complete all as specified and directed by Engr-in-Charge

M&L for preparation of old surfaces of wall/ceiling/floor by filling cracks by crack fill paste of berger or of equivalent make as approved by GE, removing loose paints etc., removing nails etc and making good surfaces by applying white birla/JK wall care putty wherever required , smoothen surfaces by sand paper and applying two coats of acrylic exterior emulsion paint over a coat of primer of Bldg upto 12.0 m height complete all as specified and directed. Note: (i) The contractor shall furnish 5 years performance warranty as per manufacturer of paint (ii) The work should be done by a company recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned complany technologist

M&L for cutting & levelling by grinding machine of old wooden floor including filling of cracks,pores etc by wood fliller materials in any description and applying melamine polishing till fair finishes complete all as directed

M&L for cutting and polishing of old floor surfaces of kota stone/terrazo/granite in any description till fair finishes and applying adequate wax finishing along with spreading of wood grain (dust) particles in 24hrs after cleaning and removal complete all as directed

S & F shelves made of HDHMR (high density high moisture resistance) board manufactured with hard wood, prelaminated both sides white in colour 18 mm thick water resistant, termite resistant, duly edge banded with PVC taping 0.8 mm thick, cut to shape & size of shelves including taking down with existing one complete all as specified and directed. Make: Action tesa, Century, Kitply

M&L 18/19mm thick particle board for insulation purposes fixed with nails to timber framed work incl taking down with existing one complete all as directed

S & F continuous (piano) hinges, stainless steel, width of flaps (when open) in 20mm, 0.8mm thickness complete all as specified & directed.

S&F in repair Collapsible steel gates, top hung,consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed

S&F in repair Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as directed

Material and labour for point wiring using approved colour coding as per IS ,with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit including all accessories, Metal flush box of suitable module, with earth dolly, covered with twin colour (specified by Engr-in- Charge)modular white cover plate & frame after chasing in brick/stone masonry walls etc for accomodating modular switches, sockets, regulators etc including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed for the following

One light / wall / exhaust fan point controlled by one, one way switch 6 Amps complete all as specified and as directed

One ceiling fan point controlled by one, one way switch 6 Amps and regulator Note : PVC Casing caping / Pipe of size as required at site on surface of ceiling (only for fan point) in lieu of concealed is permitted and is deemed to be included in the unit rate quoated.

One bell point controlled by one, one way switch 6 Amps complete all as specified and as directed

One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on same board complete all as specified and as directed

One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on independent board complete all as specified and as directed

Description all as per 70 here-in before but using 2.5 Sqmm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 Volts grade for one 6 pin socket outlet plug point,16 Amps independent including necessary running of 2.5 Sqmm PVC insulated multistranded copper conductor single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed

Supply and fixing Modular Switch - 6 Amps, Single pole one way, one module complete all as specified and as directed.

Supply and fixing Modular Bell push - 6 Amps, Single pole one way, one module complete all as specified and as directed.

Supply and fixing Modular Switch - 16 Amps, Single pole one way, one module complete all as specified and as directed.

S & F Modular socket outlet multipurpose 6 Amps, 5 pin, 2 module, complete all as specified and as directed.

S & F Modular socket outlet multipurpose 16 Amps, 6 pin-shuttered type, 2 module, complete all as specified and as directed.

Supply and fixing, Ding Dong bell suitable for operation on AC. 230 volts, single pole complete all as specified and as directed.

Supply and fixing modular fan step regulator, 120W - 2 module suitable for ( 48" & 56" fans) supply complete all as specified and as directed.

S & F Ceiling rose, 3 phase / PVC / polycarbonate, complete all as specified and as directed

Supply and fixing 20/22 Watt Inverter LED Battenaluminium body with Opal Diffuser, IP20, Battery back-up & Functioning as per Product TDS with intregrated electronic driver, connector block, holder, decorative end caps, LED tube light etc complete with all accessories prewired and mounting PVC rectangular block, including provision of flexible copper conductor cable of suitable size from ceiling rose to connector and taking down old unserviceable fitting from existing postion for carrying to store, making good disturbed surfaces complete all as specified and as directed. Make Halonix, Havells, Bajaj

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to connector, making good disturbed surfaces complete all as specified and as directed. Make Jaquar Orient Bajaj

S & F for recess mounted 2' x 2' square LED panel 36 watts, 596 x 596 x 9mm size, sleek design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed. Make- Halonix HLFPR22-11-36-CW-37mm, Philips RC383B LED 4000 PSU ODWH PIR, Jaquar LULTU1S036XC.

S & F for LED down light recess mounted luminare, round/square type 15 watts as per site requirement with efficiency of 1500 lumens per watt, Series of downlighters with low depth round & larger dia, powder coated white finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver suitable for office spaces sleek design white finish operating voltage 150 V-270 V AC, 50 Hz all as specified. Make- JAQUAR Cat part No. LNEP01S015XN/LLCN01R01SXN, Halonix HLDLR31-15CW/ HLDLR-S27-15-CW,Philips DN296B LED 15S-6500 PSU WH.

Supply & fix in replacent decorative wall mounted energy saving 03 watt or above LED bedside light fitting flexible and adjustable to any direction with integeral electronic driver complete with all accessories. philips , Havells Jaquar.

Taking down fan, Sealing cable end, dismantling blades and removing fan and blades from site and fixing or Hanging in existing position after proper cleaning , replacing unserviceable fan condenser 2.5 MFD and connecting up including provision of cable from ceiling rose or connector to fan after room plaster, colour complete all as specified and as directed.

Supply and fixing ceiling fans working on single phase input voltage 140-285 , Sweep- 1200 mm, Power 32 W, 345 RPM , with 232 Air delivery CMM (m3 /min), complete with compact BLDC Motor, blades, down rods, electronic regulator and accessories, including making connections with provision of flexible wire 23 /0.0076 twin core copper conductor from ceiling rose/connector to fan complete all as specified & as directed. Make Bajaj/ Havells/Crompton

S & F for plastic body exhaust fan, AC single phase, 240 V of size 250 mm sweep with louvers (as per Cat Part No -698502 of Make Indo Asian or equivalent Make- Bajaj Maxima DX/ Usha Crispair )including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed

Taking down carefully existing unserviceable main switch /cutout /DBs of any type, capacity and description and removing materials from site and making good disturbed surfaces of walls, floors as per the existing finishes all as specified and as directed.

S & F sheet metal enclosure MCB DB SPN 8 way with 100 Amps rated bus bar 240 Volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of disturbed surface to match the existing colour of wall complete all as specified and as directed

S & F for sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Make - Schneider/Legrand/L&T/ABB.

S & F Vertical TPN Distribution Board in sheet metal enclosure double door 4 Way, 415 volts, 50 Hz, suitable for Flush Mounting and surface Mounting & provision for FP MCCB as incomer up to 160 Amps as I/C ( Frame1) and SP/TP MCB's as outgoing (Modules Optium F1+12) , With -100 Amps Copper insulated Busbar assembly for each phase, isolated Neutral bar, 2 Earthbar and Cable ties for cable management, IP 43 - #IK 09 with metal door including necessary cement work and electrical connections complete all as specified and as directed.

S & F Distribution Board sheet metal enclosure TPN 4 Way, 415 volts, 50 Hz, suitable for Flush Mounting and surface Mounting & provision for FP MCB / Isolator / RCCB / RCBO as incomer and SP/TP MCB's as outgoing , With 100 A Copper Busbar for each phase, With 2 Neutral bar, 2 Earthbar and Cable ties for cable management, Fully insulated busbar & shrouded Neutral bars IP 43 - #IK 09 with metal door including necessary cement work and electrical connections complete all as specified and as directed.

S&F Four pole MCCB, Thermal Release Range 63-100 Amps, rupturing Breaking Capacity Icu at 415V AC 50Hz. 30 (kA) complete all as specified and as directed

S&F amp rating 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN 40 To 100 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 5 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down of old unserviceable sub main wiring of any type complete all as specified and as directed.

S & F submain wiring with 2 single core (FRLS) PVC insulated unsheathed multistranded flexible copper conductor cable, of 6.0 Sqmm and one single core 6.0 Sqmm flame retardent low smoke (FRLS) PVC insulated, unsheathed, multistranded, flexible copper cable as earthing lead , all as per IS 694/1990 drawn through including concealed in brick/stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified and as directed complete all as specified and as directed.. Note :- ( Two runs of main copper wire, one run of earth wire cable & PVC conduit shall be measured together as one length).

S & F submain wiring with 2 single core (FRLS) PVC insulated unsheathed multistranded flexible copper conductor cable, of 4.0 Sqmm and one single core 4.0 Sqmm flame retardent low smoke (FRLS) PVC insulated, unsheathed, multistranded, flexible copper cable as earthing lead , all as per IS 694/1990 drawn through including concealed in brick/stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified and as directed complete all as specified and as directed. Note :- ( Two runs of main copper wire, one run of earth wire cable & PVC conduit shall be measured together as one length).

S & F PVC rigid non-metallic flexible conduit ISI marked of dia 25 mm dia inclusive of all tees, bends, elbows reducers, junction box etc and fixing accessories such as couplers, lock nuts, saddles, etc for telephone cable , TV cable and public address system including where required all as directed by Engineer-in- Charge duly concealed in wall complete all as specified and as directed

S & F PVC rigid non-metallic flexible conduit ISI marked of dia 20 mm dia inclusive of all tees, bends, elbows reducers, junction box etc and fixing accessories such as couplers, lock nuts, saddles, etc for telephone cable , TV cable and public address system including where required all as directed by Engineer-in- Charge duly concealed in wall complete all as specified and as directed

S&F for sheet metal enclosures single pole and neutral enclosure with a two pin and earth plug and socket complete with one MCB SP 20/ 32Amps including removal of old unserviceable one complete all as specified and as directed.Make - Scheinder/Legrand/L&T/ ABB

Earthing complete with galvanized steel earth plate electrode of size 60cm X 60 cm X 6 mm buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of plate not less than 1.5 m below the normal ground level connected to GI earth strip 32 X 6 mm dia GI earth lead as earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel, protected by GI pipe light grade 40mm bore all as shown on electrical plate No 3 of SSR Part-I connected to earth test point electrode, PCC pit with RCC cover, funnel with wire mesh, watering pipe 20mm dia protection pipe etc and testing on completion complete including removal of old unsv earthing material all as specified and directed. Note No 1 :- The unit rate shall also include for earth work in hard/dense soil, PCC (1:3:6) type C1 chamber, RCC 1:2:4 type B-1 cover 50 mm thick reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, funnel with watering pipe 20 mm dia medium grade, GI protection pipe light grade 40 mm dia and wire mesh complete. Note No 2 :- Earthing strip and GI protection pipe beyond 7.5 m will be measured and paid separately if required

Supply and Installation, commissioning of Inverter type wall mounting air cooled split type unit air conditioner electric driven single phase indoor unit and outdoor unit with cordless remote control unit and with in built airioniser and plasma filter for better indoor air quality cutting ,brazing and connecting the copper pipe of size 1/2 inch and 1/4 inch size of pipe and making holes as for passing of copper pipes and electric cables and pressure testing with nitrogen and freon gas vacumising the system and charging the Non CFC refrigerent and testing the complete system for smooth functioning of split AC up to satisfactioning, above 4 star rating, confirming to IS-1391 Para II 1992 herimatically sealed air compressor working with Non CFC refrigerent suitable for wall mounting 4500 K cal/ hrs 1.5 Ton complete with stand for fixing on wall/ground all as specified and directed. Make Hitachi, Daikin, Voltas

Supply and fix MCB Protected Socket with sheet steel enclosure SRCD(socket residual current device) single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amps MCB single pole.

S & F for copper tubing of size 1/4” for discharge line any make of split AC of capacity 1.5 ton with insulation sheet of pipe tube type insulation complete all as specified and directed.

S & F for copper tubes of size 1/2” for Suction line of split AC of capacity 1.5 ton including insulation sheet of pipe tube type insulation complete all as specified and directed.

S & F for flexible PVC pipe 15mm dia heavy duty from outdoor unit to indoor unit for drain of water complete all as specified and directed.

S & F for new powder coated Mild Steel fabricated stand suitable for outdoor unit of Tower AC of 1.5 TR to install outdoor unit on wall/ floor as required on site with legs and bracing complete all as specified and directed.

Supply and Installation, commissioning of wall mounting air cooled split type unit air conditioner electric driven single phase indoor unit and outdoor unit with cordless remote control unit and with in built airioniser and plasma filter for better indoor air quality cutting ,brazing and connecting the copper pipe of size 1/2 inch and 1/4 inch size of pipe and making holes as for passing of copper pipes and electric cables and pressure testing with nitrogen and freon gas vacumising the system and charging the Non CFC refrigerent and testing the complete system for smooth functioning of split AC up to satisfactioning, 5 star rating, confirming to IS-1391 Para II 1992 herimatically sealed air compressor working with Non CFC refrigerent suitable for wall mounting 6000 K cal/ hrs 2.0 Ton complete all as specified and directed. Make Hitachi, Daikin, Voltas

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with multistranded copper conductor of size 04 Sq. mm nominal area and drawing into PVC non metallic rigid heavy duty conduit ISI marked and its accessories including one run of PVC insulated 2.5 Sqmm (nominal area) FRLS multistranded copper conductor cable as earth wire complete all as specified and as directed.

3. S & F for Sheet metal enclosure with socket plug top and MCB of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amp 240 volts SP complete all as specified and as directed

4. Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type wall mounted and designed for input variation between 170 volts to 250 volts with out put voltage stablized at 230 volts with accuracy of + 2.5% and capacity 5 KVA suitable for AC complete all as specified.

S & F decorative LED bollard warm white with aluminum die casting, with adequate size elecrical connections complete all as specified and as directed. Make: Halonix Cat No HLOB-95-10-ww-01 (LLD0003139)

S&F for factory made srteet light control panel, with and including all accessories such as control switch, contactor, automatic control relay, pre-wired etc. fixed on fabricated angle iron channel of suitable size and grouting on floor, Timelite-32 Amps, 3 Pole 230/415 volts-Astronomical Time switch (suitable for Pune area), Make -Indo-Asian Cat No.TLO32ASO or equivalent in Havells, Legrand.

M & L Cement Concrete 1:3:6 (20 mm graded aggregate) as in coping of pole etc including form work & finishing the surfaces even & smooth with out using extra cement complete including demolition of old PCC work all as specified

Excavation in trenches not exc 1.50 Metre wide and not exc 1.50 Metre depth for laying of UG Cable/Pole/Stays etc getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Leveling, Watering and Well Ramming in layers not exc. 25 CM thick in Soils, complete all as specified and as directed.

Removing Surplus soil to a distance not exc 50.00 Metre away and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and as directed.

Supply and laying 40mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS- 14930 Pt-II with antirodent and non flame propogating properties plete with fittings for cable protection complete all as specified and as directed.

Taking down and Supply, lay, joint, test and commissioning of LT under ground cable 1100 volt grade , XLPE insulated and PVC sheathed heavy duty armoured with aluminium conductor , IS 7098-I Marked, Laid in trenches/ducts/fixed on poles/walls/laid under roads/paths/drains/culverts or encased in GI pipe including cable glands, lugs jointing material etc complete all as specified and directed. cable of the following size.

(a) 10 Sq mm 2 Core

(b) 16 Sq mm 4 Core

Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

N AND G CONSTRUCTION (BID ID -3120082)

A.S.ENTERPRISES (BID ID -3113311)

AJINKYA VIKRAM GAIKWAD (BID ID -3123379)