CONSTRUCTION OF COMMUNITY HALL IN WARD NO.-12

Boring, Providing and installing cast in situ single under reamed piles of specified diametre and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinfrement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc all complete .(Length of pile for payment shall be measured upto to the bottom of pile cap).

Per Mtr

63 CM (25) UNDER -REAM Making 63 cm (25) dia under ream at required with hand auger of approved quality in ordinary soil (vide classification of soil ifem - A) true to plumb and without eccentri city in my stage of opration and disposal of the excavated earth up to 50 mts lead in eluding all lifts , all complete as per approved design and direction of (E/l)

Earthwork in excavation in foundation trenches or drains(not exceeding 1.5m in width or 10 sqm on plan)including dressing of sides and ramming of bottom lift upto 1.5m,including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m All kinds of soil.

Filling available excavated earth(including rock)in trenches ,plinth,sides of foundation etc.in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead.

Supplying and Filling in plinthy with local sand and under floors including watering ,ramming consolidating and dressing complete.

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

cement mortar 1:4 (1 cement : 4 coarse sand)

Extra tor Brick work in superstructure above plinth level upto floor V cum

Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in superstructure above plinth and upto floor V level.

Per Sqm

Brick Bat Filling with all comp job as per direction of E/I

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering work upto plitn level: 1:1.5:3(1Cement :1.5 Coarse sand:3 graded tone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement -All work upto plinth level 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upto floor five level excluding cost of centring, shuttering, finishing, and reinforcement.

Per Cum

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 degree, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectevely at all floor levels.

Providing M-15 grade R.C.C. instead of M-20 grade R.C.C.

Centering and shuttering including strutting,propping etc and removal of form for:

Providing and laying damp Proof course 50mm thick wioth cement concrete 1:2:4(1cement :2:coarse sand:4 graded stone aggregate 20mm nominal size)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding complete.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Per K.g

Providing and fixing circular cast iron box for ceiling fan clamp 140mm internal diameter 73mm height,5mm thick rim bottom and top lids 1.5mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3mm dia round headed screws,one at the corners :Clamps shall be made of 12mm dia M.S bar bent to shape as per standard drawing.

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all comlete.

Per K.g

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge

Per K.g

Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Per Sqm

UPVC blind pipe 100 mm dia as per IS: 12818 do- all comp job as per direction of E/I

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 110 mm bend

Close timbering in case of shafts, wells, cesspits, mannoies and the like including strutting, shoring and packing cavities (wherever required) complete (Measurements to.be taken of the face area timbered): Depth exceeding 3 m but not exceeding 4.5 m

Providing wood work in frames of doors windows,clearstory window and other frames,wrought framed and fixed in position Local wood.

Per Cum

Providing and fixing flush door shutters conforming to IS : 2202 (part-I) non decorative type core of block board construction with frame of 1st class tiard wood and well matched commercial 3 ply vennering with vertical grains of cross bands and face veneers on both faces of shutters.

Per Sqm

Providing and fixing aluminium sliding tower bolt (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts screws etc. necessary screws etc. complete.

Per Nos

Providing and fixing bright finished brass 100mm mortice latch and lockwith 6 lever handles with necessary screws etc. complete (best make of approved quality)

Providing and fixing bright finished brass hangging type floor door stoper with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extuded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, at top, bottom and sides with required EDPM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust fre straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/paneling, C,P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately.)

Per K.g

Providing and fixing glazing in aluminium door, window, ventilator shutters and partions etc. with EDPM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.)

Per Sqm

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Per Sqm

Providing desination 100 A one brick flat soling joints filled with local sand including cost of watering texes, roualty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:1:2 ( 1 cement: 1 coarse sand:2 graded stone aggregate 20 mm nominal size)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture) of approved make in all colours, shades except begundy, bottle green,black of any size as approved by Engineer-in-chage in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 (1 Cement:3 Coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc.,

Per Sqm

Cement plaster in course sand 12mm cement plaster of mix :

Per Sqm

6mm cement plaster to ceiling of mix:

Per Sqm

20mm cement plaster of mix :

Per Sqm

12 mm cement plaster 1:4( 1 cement: 4coarse sand) finished with a floating coat of near cement Details of cost for 10 sqm

Per Sqm

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade.

Per Sqm

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade:

Per Sqm

Finishing walls with textured exterior paint of required shade :

Per Sqm

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete,including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm(S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs,unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required length including cutting brick work andscrewed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wallfixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc completeetc complete

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour,weighing not less than 105 gms.

Providing and fixing brass bib cock of approved quality :

Providing and fixing brass stop cock of approved quality

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

Meter

Meter

Meter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supplying, installation, testing & commissing of 1 HP submersible pump & motor having discharge 1.5 lps against a total haed of 35 m (approx) of KSB/Kirloskar or eequivalent make with all accessories & fittinggs etc incluuding loaading unloaadingg & transportation of pump set to the work site with all required labour , materials, tools & tackles installation, testinng & comissioning as per standards specification & direction of E/I

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well screen (RMS) pipe with ribs, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc.all complete, for all depths,as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well screen (RMS) pipe with ribs, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc.all complete, for all depths,as per direction of Engineer -in-charge.

P/Pair

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method,measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with piano type switch, phenolic laminated sheet , suitable size M.S./PVC Box etc as required.

Point

Wiring for twin control light point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size PVC / MS box etc as required

Wiring for circuit /sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor,single core cable in surface / recessed medium class PVC conduit as required.

Meter

Meter

Supplying and fixing following piano type switch / socket on the existing switch box/cover including connections etc.as required.

Supplying and fixing 2 pin, 6 amp ceilling rose on the existing junction box/wooden block including connection etc as required.

Supplying and fixing batten/angle holder including connection etc.as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated copper conductor etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/fixture etc.as required

Earthing with G.I. earth pipe 4.5 meter long ,40 mm dia including accessories,and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar,earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Add for sign.board,scheme name plate & Colour photo graph (Payment after providing actual voucher)