SPECIAL REPAIR TO BLDG NO P-157 AND P-11 UNDER AGE (I) POKARAN MIL STN

Amount

Dismantling of floors health or walls tiling and Stone floor including cement mortar bedded (but not backing) & removing serviceable tiles to store and rubbies of the premises complete all as specified & directed by Engineer-in-charge.

M&L for non skid ceramic coloured tiles of 7 to 8mm thick, (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm (including size 400mmx400mm), as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge.

S&F joint free non skid ceramic coloured tiles 7 to 8mm thick(square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 Sqm, in floors laid over & incl 15mm thick screed bed of CM 1:6 ,etc set and jointed in neat cement slurry and pointed in white or colored cement to match complete all as specified & directed by Engineer-in-charge.

. --Ditto-- all as per item No 03 above but as in skirting over & including 10mm thick backing coat of CM 1:4 complete all as specified & directed by Engineer-in-charge.

S&F coloured glazed ceramic tiles size 350x250x7mm /450x350x7 mm thick on vertical surfaces, set & joined in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including backing coat of 10mm thick in CM (1:4) all as specified & directed by Engineer-in-charge.

Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified & directed by Engineer-in-charge.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 25 to 55 mm as per the requirements complete all as specified & directed by Engineer-in-charge.

M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only) complete all as specified & directed by Engineer-in-charge.

Supply only integral Waterproofing compound complete all as specified & directed by Engineer-in-charge.

M&L for water proofing treatment with 3 mm thick APP (Actatic Poly Propylene) modified membrane reinforced with non woven polyester mat of weight 150 gms/sqm as centre core & without multiple layers of polyethylene applied by thermo fusion using LPG torch on the bottom portion of the membrane after applying a coat of bituminous primer @ 0.3 kg/sqm over roof (an overlap of 100 mm & 150 mm shall be provided on sides & end respectively )including a coat of bitumen grade 85/25 @ 1.20 Kg/Sqm and applying one coat of aluminium paint @ 100ml/sqm on top of APP membrane to get uniform finish complete all as per specified and directed.

Taking down cement plaster on stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified & directed by Engineer-in-charge.

M&L rendering 15mm thick in 1:6 cement plaster on stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified & directed by Engineer-in-charge.

M&L rendering 15mm thick in 1:4 cement plaster on of stone masonary surface is to be finished even and smooth (without using extra cement) complete all as specified & directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bond distemper over 3 mm thick wall care putty including one coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for preparation of plastered surfaces of wall and applying three coats of white wash complete all as specified & directed by Engineer-in-charge.

Finishing wall with Acrylic emulsion smooth exterior paint of reqd shade, new work (two or more coat) applied @ 1.67 Ltr/10 Sqm over and incl priming coat of exterior primer applied @ 2.20 Kg/10 Sqm complete all as specified & directed by Engineer-in-charge.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified & directed by Engineer-in-charge.

S & F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.560mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified & directed by Engineer-in-charge.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. Fixed as in Ridge complete all as specified & directed by Engineer-in-charge.

Dismantling of Stone slabs and tiles of any description or thickness in floors, walls, aprons etc., removing serviceable tiles to store and rubbish off the premises complete all as specified & directed by Engineer-in-charge.

M&L for Kota stone flooring 20-25mm thick incl for cuttting and polishing by machine over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 20 mm thick screed bedding in CM (1:6) complete all as specified & directed by Engineer-in-charge.

Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting,dado,and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 10 mm thick backing coat of CM (1:3) complete all as specified & directed by Engineer-in-charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc ) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified & directed by Engineer-in-charge.

S&F for anodised aluminium snap grid 605 x 605 mm frame work for false ceiling all as specified and directed,Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified & directed by Engineer-in-charge.

M&L for providing and fixing Gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified & directed by Engineer-in-charge.

M/s Shri Inder Construction Company

Habib Traders