Provison of waiting hall and washroom for visitor and parents at Bhagirathi Bhawan at NIT Kurukshetra

of Earth up to 5 km

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

3 2.25 layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and cum 60.11 270.03 16231.20

watering, lead up to 50 m and lift up to 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or

stacked materials.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15

cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

6 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

6.1 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% liter 11.75 213.62 2510.00

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment

(excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one liter per hole, 300 mm

7.1 2.35.3 apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2

Coarse sand) to match the existing floor:

a 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration sqm 58.73 272.36 15995.96

II 4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand) derived from natural sources : 4 graded stone aggregate 20

mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone

aggregate 40 mm nominal size derived from natural sources)

9 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for :

9.1 4.3.1 Foundations, footings, bases for columns sqm 6.06 327.44 1984.31

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2

10 4.11 coarse sand (zone-Ill) derived from natural sources: 4 graded stone aggregate 20 mm nominal sqm 12.66 480.88 6087.91

size derived from natural sources).

Digitally signed by2/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Extra for providing and mixing water proofing material in cement concrete work in doses by

weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality

12 4.13 using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and sqm 12.66 121.06 1532.58

finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-

III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from

13 4.17 natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and sqm 31.29 724.80 22678.94

consolidated and grouted with fine sand, including necessary excavation, levelling & dressing &

finishing the top smooth.

III 5.0 REINFORCED CEMENT CONCRETE

14 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

14.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 28.38 327.44 9292.84

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

14.3 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 49.32 815.07 40199.38

14.4 5.9.4 Shelves (Cast in situ) sqm 2.40 815.07 1956.17

14.5 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 103.22 646.86 66768.22

14.6 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 77.99 855.16 66689.58

14.7 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 699.39

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string

courses, bands, copings, bed plates, anchor blocks and the like

14.9 5.9.16 Edges of slabs and breaks in floors and walls

13.10 5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 4.89 866.54 4233.03

Extra for additional height in centering, shuttering where ever required with adequate bracing,

propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5

m, for every additional height of 1 metre or part thereof (Plan area to be measured).

15.1 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 339.46

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete upto plinth level.

16.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 2127.50 95.32 202803.61

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete above plinth level.

17.1 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 2731.25 95.32 260355.98

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Digitally signed by3/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

19 5.33 reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix

shall be payable separately. In case the cement content in design mix is more than 110%

of the specified minimum cement content, the contractor shall have discretion to either re-

design the mix or bear the cost of extra cement.

19.1 5.33.1 All works upto plinth level

a 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 17.02 9233.48 157153.91

19.2 5.33.2 All works above plinth level upto floor V level

a 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 21.85 10958.58 239445.03

IV 6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

20.1 6.1.2 Cement mortar 1:6 (1 cement :6 coarse sand) cum 0.33 7079.72 2336.31

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in:

21.1 6.4.2 Cement mortar 1:6 (1 cement :6 coarse sand) cum 19.30 8813.00 170090.95

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

in superstructure above plinth level up to floor Vlevel.

22.1 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 32.55 1082.49 35235.13

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half

V 8.0 CLADDING WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and

similar locations of required size, approved shade, colour and texture laid over 20 mm

24 8.2 thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white

cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high gloss finish etc. complete at all levels.

25 8.2.2 Granite stone slab colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including

26 8.3 machine polishing to edge to give high gloss finish etc. complete as per design approved

by Engineer-in-Charge.

Digitally signed by4/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia

27 8.4 and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. metre 2.70 505.65 1365.26

Extra for providing opening of required size & shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including moulding, rubbing and polishing of

cut edges etc. complete.

VI 9.0 WOOD AND P. V. C. WORK

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters:

29.1 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 12.00 2143.35 25720.16

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges

of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass

excluded) (overall area of door shutter to be measured):

31.1 9.24.1 Rectangular or square sqm 8.40 184.96 1553.67

Providing and fixing wooden moulded beading to door and window frames with iron screws,

plugs and priming coat on unexposed surface etc. complete :

33 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). sqm 12.00 99.58 1194.94

Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to

80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary

accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less

35 9.96 than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts

and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than

36 9.97 grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than

37 9.100 grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with ecessary

screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating

38 9.101 not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade,

with necessary screws etc. complete.

9.101.2 Twin rubber stopper each 6.00 66.19 397.14

Digitally signed by5/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six

levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)

aluminium lever handles of approved quality with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/

suede finish with high density protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

VII 10.0 STEEL WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position

41 10.25 and applying a priming coat of approved steel primer using structural steel etc. as required.

41.1 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 151.31

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10

mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising

of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/

masonry, etc. as per direction of Engineer-in-charge.

VIII 11.0 FLOORING WORK

43 11.24 Extra for pre finished nosing to treads of steps of marble stone. metre 4.80 630.86 3028.11

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of approved

brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1

cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of

required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

45.1 11.41A.1 Double charge vitrified tile polished finish of size

46.2 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer),

with water absorption less than 0.08 % and conforming to LS. 15622, of approved make, in all

colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1

cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the

joint with white cement & matching pigments etc complete.

Digitally signed by6/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as

well as curvilinear portions of the building all complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

47 11.56 sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing and polishing etc. all complete as specified

and as directed by the Engineer-in-Charge.

47.1 11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent sqm 30.30 4156.23 125933.68

IX 12.0 ROOFING WORK

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar

refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and

sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement :

48 12.21 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,

including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting

upto 150 mm height along the parapet walls in the same manner.

12.21.1 In 75x75 mm deep chase metre 31.29 276.67 8657.02

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1

49 12.22 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a each 2.00 283.48 566.95

coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar

refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and

sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement :

50 12.55 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, sqm 60.09 1536.36 92320.00

including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting

upto 150 mm height along the parapet walls in the same manner.

X 13.0 FINISHING WORK

51 13.4 12 mm cement plaster of mix :

52 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

53 13.16 6 mm cement plaster of mix :

54 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @ 2.20kg/10 sqm

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

55.1 13.61.1 Two or more coats on new work sqm 139.77

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare

the surface even and smooth complete.

Digitally signed by7/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Distempering with oil bound washable distemper of approved brand and manufacture to give an

57 13.41 even shade :

New work (two or more coats) over and including water thinnable priming coat with cement

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less

58 13.82 than 50 grams/ litre, of approved brand and manufacture, including applying additional coats

wherever required, to achieve even shade and colour.

XI 21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM

59 21.1 rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including cleat angle, Aluminium snap beading for

glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings

and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for

59.1 21.1.1 For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

60 21.1.2 making provision for fixing of fittings wherever required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/

Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over

61 21.19 backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge

complete, complying to ASTM C920, DIN 18540-F & ISO 11600

61.1 21.19.1 Upto 5 mm depth and 5 mm width metre 55.30 138.44 7655.82

XII 22.0 WATER PROOFING WORK

Digitally signed by8/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and laying integral cement based water proofing treatment including preparation of

surface as required for treatment of roofs, balconies, terraces etc consisting of following

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water

proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC

slab including adjoining walls upto 300 mm height including cleaning the surface before

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50%

of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement

mortar of mix 1:5

(1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto

300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse

62.1 22.7.1 sand) admixedthickness

With average with water

120 mm compound conforming

and minimum toat

thickness ISkhurra

mm. by Engineer- sqm 60.09 1619.35 97306.91

TOTAL FOR CIVIL WORKS

1 Internal Plumbing Works.

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick hard

1 17.31 board ground fixed to wooden cleats with C.P. brass screws and washers complete. sqm 2.00 1500.48 3000.95

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the

direction of Engineer-in-charge.

3 DSR-17.34 Providing and fixing toilet paper holder :

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan)

with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with

4 17.2 manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and

floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 5891.27

Digitally signed by9/21

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and fixing white vitreous china extended wall mounting water closet of size

780x370x690 mm of approved shape including providing & fixing white vitreous china cistern

5 17.78 with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including Each 2.00 13861.76 27723.53

seat cover, and cistern fittings, nuts, bolts and gasket etc

6 ,18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

18.49.1 15 mm nominal bore Each 2.00 461.68 923.37

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality

conforming to IS:8931

18.53.1 15 mm nominal bore Each 6.00 532.02 3192.13

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P.

8 17.7 brass waste of standard pattern, including painting of fittings and brackets, cutting and making

good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps]

9 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions : Each

18.21.2 45 cm length

18.21.2.1 15 mm nominal bore Each 4.00 90.59 362.37

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

18.22.2 150 mm diameter Each 202.13

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved

by Engineer in charge.

a 15 mm nominal dia Each 6506.49

Providing and fixing C.P. cast brass twin coat hooks fixed to PVC rawl plug with SS screws Make

Euronics, Cat. No. EC02 or approved equivalent.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S.

13 17.16.A triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in- Each 2.00 318.30 636.60

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with

15 17.72 minimum distances of 37 mm from wall face with concealed fittings arrangement of approved Each 2.00 217.66 435.32

quality and colour,weighing not less than 88 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of

75mm with concealed fitting arrangements,weighing not less than 106 gms.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with

white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders

17 17.5 with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet

grating and other couplings in C.P. brass, including painting of fittings and cutting and making

good the walls and floors wherever required :

17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern Each 1.00 10769.42 10769.42

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP

brass screws with concealed fittings arrangement of approved quality and colour.

Supply, installation, testing and commissioning of horizontal type storage hot water heater within-

19 MR built pressure relief valve, rated for inlet water pressure upto 6 bar complet in all respects

including inlet, oulet connections, fixing bolts etc. and testing complete.

25 Lits. Each 8692.83

B Soil, Waste, Vent & Rain Water Pipes

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet

20 12.22 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a Each 2.00 283.48 566.95

coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and

weighing not less than 440 grams.

22 17.35 Providing and fixing soil, waste, vent and rain water pipes

17.35.1.3 Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 metre 25.00 1128.43 28210.68

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe

embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and

making good the walls etc.

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm

thick, bolts and nuts complete.

17.38.1.3 Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 4.00 585.67 2342.66

25 17.39 Providing and fixing plain bend of required degree.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

17.39.1.3 Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 6.00 367.95 2207.73

26 17.42 Providing and fixing double equal plain junction of required degree.

17.42.1.3 Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 Each 2.00 766.32 1532.64

27 17.44 Providing and fixing single equal plain junction of required degree :

17.44.1.3 Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 2.00 609.80 1219.61

28 17.48 Providing and fixing single unequal plain junction of required degree

17.48.1.3 Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 2.00 574.29 1148.58

Providing and fixing Hubless cast iron offsets epoxy coated inside & outside as per IS : 15905

17.54A.1 130 mm offsets

30 17.56 Providing and fixing terminal guard:

17.56.1.3 Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 1.00 424.89 424.89

31 17.57A Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe

17.57A.1.1 SS 304 grade coupling with EPDM rubber gasket Each 75.00 432.02 32401.41

Painting with synthetic enamel paint of approved drand and manufacture to give an even shade

13.61.1 Two more coast on new work sqm 35.00 139.77 4891.98

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level:

4.1.3 1:2:4 (1 cement :2 coarse sand: 4 hard stone aggregate 20mm and down gauge). Cum 3.00 7831.36 23494.09

Providing and fixing trap of self cleansing design with screwed down or hinged with or without

34 ,17.60 vent arm complete, including cost of cutting and making good the walls and floors.

a 17.60.1 100 mm inlet and 100 mm outlet

17.60.1.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 Each 4.00 809.01 3236.05

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

b 17.60.2 100 mm inlet and 75 mm outlet

17.60.3 Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 Each 588.48

35 NS-13 Providing and fixing SS grating of approved quality and colour.

Circular type 125 mm nominal dia [Make :Euronics, Model: EFG01P-55]. Each 4.00 1030.43 4121.72

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS

1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and

36 Fire DSR 18.8 fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required :

For WB, Urinal FT & FD and Sink Drain pipe

18.8.3 40 mm dia nominal bore Metre 5.00 883.60 4418.01

18.8.4 50 mm dia nominal bore Metre 3.00 985.68 2957.04

Providing & fixing on wall face unplasticised -Rigid PVC rain water pipes conforming to IS:13592

37 12.41 Tyape A included jointing with seal ring conforning to IS:5382 leaving 10 mm gap for thermal

expansion. (i)Single socketed pipes.

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised -

38 12.42 Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring

conforming to IS ; 5382 leaving 10 mm gap for thermal expansion.

12.42.1.2 Coupler -110 mm diameter Each 2.00 127.54 255.09

12.42.5.2 Bend -87.5 deg -110 mm diameter Each 2.00 140.36 280.71

External Drainage System

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and

dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated

41 DSR-2.10 soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including

consolidating each deposited layer by ramming, watering, etc. and disposing of surplus

excavated soil as directed, within a lead of 50 m :

a 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 10.00 443.77 4437.68

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m,

42 DSR-2.11 but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

a a. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Metre 2.45 574.55 1408.96

Fixing SW Gully Trap Grade A Complete CI Grating, brick masonry chamber and water tight CI

43 ,19.4 cover frame of 300 x 300 mm size (inside) square mouth traps or "P" or "S" Type Traps.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with

R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone

aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-

III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making

channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) finished with a floating coat of neat cement complete as per standard design :

(A) Inside size 90×80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610

mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of

cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover

with frame (medium duty) 500 mm internal diameter, total

weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame

19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 Each 1.00 25950.79 25950.79

45 18.8.1.1 Extra over item No. 25.4 for every additional depth of 0.10 m. or part there of manhole.

a 19.8 Extra for depth for manholes

19.8.1 Size 90x80 cm

19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 metre 1.00 8641.92 8641.92

b 19.8.2 Size 120x90 cm

19.8.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 metre 1.00 10361.06 10361.06

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS :

10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23

mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm

space between protruded legs having 2 mm tread on top surface by ribbing or chequering

besides necessary and adequate anchoring projections on tail length on 138 mm as per

standard drawing and suitable to with stand the bend test and chemical resistance test as per

specifications and having manufacture's permanent identification mark to be visible even after

fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3

coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with

DSR-19.6 stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of

joints etc. complete :

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone

47 DSR-19.3 aggregate 40 mm nominal size) up to haunches of RCC. pipes including bed concrete as per

standard design :

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1

48 DSR-19.27 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame

complete as per standard design

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Making connection of drain or sewer line with existing manhole including breaking into and

making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3

(1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary

channels for the drain etc. complete for pipes 100 to 250mm dia.

C Internal Water Supply

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with

62 18.7 clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of Engineer in Charge.

Internal Work - Exposed on Wall

a 18.7.3 25 mm nominal outer dia .Pipes. Metre 5.00 434.41 2172.06

a 18.7.4 32 mm nominal outer dia .Pipes. Metre 20.00 532.66 10653.20

b 18.7.5 40 mm nominal outer dia .Pipes. Metre 10.00 717.04 7170.36

18.7.6 50 mm nominal outer dia .Pipes. Metre 985.68

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with

63 ,18.8 clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.

a 18.8.2 20 mm nominal outer dia .Pipes. Metre 30.00 546.27 16388.11

b 18.8.3 25 mm nominal outer dia .Pipes. Metre 8.00 665.68 5325.43

Providing and fixing G.I. pipes with two coats of anti-corrosive bitumastic paint of approved

64 ,18.10 quality : complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Internal work - Exposed on Wall

a 18.10.1 & 18.40.1 15 mm dia nominal bore Metre 5.00 334.09 1670.44

b 18.10.2 & 18.40.2 20 mm dia nominal bore Metre 5.00 409.74 2048.71

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS

1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and

65 Fire DSR - 18.8 fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more

coats of synthetic enamel paint of required shade complete as required :

c DSR Fire-18.8.1 25 mm dia nominal bore Metre 5.00 646.49 3232.43

d DSR Fire-18.8.2 32 mm dia nominal bore Metre 10.00 721.98 7219.81

e DSR Fire-18.8.3 40 mm dia nominal bore Metre 25.00 883.60 22090.06

f DSR Fire-18.8.4 50 mm dia nominal bore Metre 985.68

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1

cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with

hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1

cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering

with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of

neat cement complete as per standard design :

a 18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Each 1.00 1820.53 1820.53

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701

marked, with cover and suitable locking arrangement and making necessary holes for inlet,

outlet and overflow pipes but without fittings and the base support for tank.

Making core cutting machine up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe

etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so

as to make it leak proof.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

18.17.1 25 mm nominal bore Each 2.00 566.05 1132.10

18.17.2 32 mm nominal bore Each 1.00 627.24 627.24

18.17.3 40 mm nominal bore Each 1.00 752.07 752.07

18.17.4 50 mm nominal bore Each 933.84

70 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) :

18.19.6.2 80 mm nominal bore Each 3759.99

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Providing and fixing forged brass ball valve of brass body with hard chrome plated steel ball

71 NS 16 inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads

complete in all respects.

a 15 mm nominal bore Each 2.00 368.00 736.00

b 20 mm nominal bore Each 2.00 513.00 1026.00

Providing and fixing forged brass single acting air release valve with screwed inlet 25 mm dia.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic

floats complete :.

a 18.18.3 25 mm nominal bore Each 1.00 424.42 424.42

TOTAL FOR PLUMBING WORKS

I SUB HEAD (I) :- INTERNAL WIRING

DSR-2022 for Electrical works

1 Point wiring

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

1.10 conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

2 Group/Loop Control Point wiring in PVC conduit, with modular type switch :-

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core

1.55 cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable etc. as required.

3 Twin Control Point wiring in PVC conduit, with modular type switch :-

Wiring for twin control light point with 1.5 Sq.mm FRLS PVC insulated copper conductor single

core cable in surface/recessed medium class PVC conduit, 2 way modular switch, modular

plate,suitable GI box and earthing the point with 1.5 Sq.mm FRLS PVC insulated copper

conductor single core cable etc. as required.

4 Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :-

Wiring for light /power plug with 2 x 4 Sq.mm. FRLS PVC insulated, copper conductor single

core cable in surface / recessed medium class PVC conduit along with 1 no. 4 Sq.mm FRLS

PVC insulated copper conductor single core cable for loop earthing as required.

5 Circuit / Sub main wiring in PVC conduit :-

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC

1.14 insulated, copper conductor single core cable in surface/ recessed medium class PVC conduit

Supply and fixing of following sizes of medium class PVC conduit along with accessories in

6 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit

Supplying and fixing of METAL BOX following sizes (nominal size) on surface or in recesss with

7 1.22 suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in

8 1.31 recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. Each 7.00 507.19 3550.36

modular switch, connection etc. as required.

9 S/F power plug point modular type accessories :-

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in

1.32 recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 Each 5.00 623.09 3115.47

amps. modular switch, connection etc. as required.

10 S/F modular type electronic fan regulator :-

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate

1.25 switch box including connections but excluding modular plate etc. as required. Each 1.00 392.36 392.36

11 S/F modular type blanking plate :-

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding

modular plate as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including

connections etc. as required.

13 1.34 Supplying and fixing brass batten/ angle holder including connection etc. as required. Each 1.00 139.29 139.29

II SUB HEAD (II) :- DISTRIBUTION BOARDS & MCB's

Supplying and fixing 20 A, 240 volts, SPN industrial type socket outlet, with 2 pole and earth,

metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on

surface or in recess, with chained metal cover for the socket out let and complete with

connections, testing and commissioning etc. as required.

Supplying and fixing 5 amps. to 32 amps. rating, 240/415 V, 10kA, "C" curve, miniature circuit

2 2.1 breaker (MCB) suitable for inductive load of following poles in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without MCB/RCCB/

2.4.2 6 way, Double door Each 1.00 5288.85 5288.85

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual

current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

III SUB HEAD (III) :- EARTHING

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with

existing surface / recessed conduit / submain wiring / cable as required.

Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing along with

existing surface / recessed conduit / submain wiring / cable as required.

IV SUB HEAD (IV) :- INTERNAL LIGHTING FIXTURES & FANS

V ERECTION OF FANS

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling

fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm

long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less

than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 CMM, 350 RPM

3 19.1 (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for Each 4.00 2902.81 11611.24

speed control and all remaining accessories including safety pin, nut bolts, washers, temperature

rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50

Hz, single phase AC Supply, earthing etc. complete as required.

Installation of exhaust fan in the existing opening, including making good the damage,

connection, testing, commissioning etc. as required

LIGHTING FIXTURES & FANS

Supply, installation, testing and commissioning of wall / ceiling / LED light luminaires with all

1 MR accessories as per standard item etc complete as required as per the standard catalogue item.

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Supply, installation, testing and commissioning of 2ft 10W LED Batten delivering an initial

system lumen of 1000 lumens & the luminaire shall be with system efficacy ≥ 100 lm/W. The

housing should be made of Extruded Aluminium with polycarbonate diffuser. The operating CCT

shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with

input voltage range of 150 to 270V , PF ≥ 0.9 ,THD ≤ 10%, 50,000 Hrs LED Life with L70 Criteria

and Ingress Protection of IP20. Luminaire shall have minimum surge protection of 2.5KV. The

luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along

with Photo Biological Safety Standard.

Wipro Cat. Ref. LL20-111-XX65AL5IB (Trim Neo LL20 Series)

Supply, installation, testing and commissioning of 4ft 20W LED Batten delivering an initial

system lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 lm/W. The

housing should be made of Extruded Aluminium with polycarbonate diffuser. The operating CCT

shall be 5700K with CRI of ≥80. The luminaire shall be with BIS Registered electronic driver with

input voltage range of 150 to 270V , PF ≥ 0.95 ,THD ≤ 10%, 50,000 Hrs LED Life with L70

Criteria and Ingress Protection of IP20. Luminaire shall have minimum surge protection of

2.5KV. The luminaire shall be with following certifications: LM79 & LM80 issued by LED

manufacture along with Photo Biological Safety Standard.

Wipro Cat. Ref. LL20-281-XX57AL5IB

Supply, installation, testing and commissioning of 24W Surface Mounted Round Led

Downlighter delivering minimum system lumen of 2400 lm & the luminaire shall be with system

efficacy ≥ 100 lm / W. Housing is Pressure Die Cast Aluminium, powder coated white with

Optics: HET Diffuser. Ingress Protection should be IP20. The operating CCT shall be 5700K with

CRI of ≥80. The luminaire shall be BIS Registered with isolated type electronic driver in

polycarbonate / metal enclosure with input voltage range of 100 to 265V , THD ≤ 10% & PF ≥

0.90, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall be of same make and made in

India for ease of repair and service. The LED shall be SMD type. Luminaire shall have minimum

surge protection of 2.5KV. The luminaire shall be with following certifications: LM79 & LM80

issued by LED manufacturer along with Photo Biological Safety Standard.

Wipro Cat. Ref. LD06-301XXX-57SMBT

Supply, installation, testing and commissioning of 18W Surface Mounted Round Led

Downlighter delivering minimum system lumen of 1800 lm & the luminaire shall be with system

efficacy ≥ 100 lm / W. Housing is Pressure Die Cast Aluminium, powder coated white. IP20 ,

Optics: HET Diffuser. The operating CCT shall be 5700K with CRI of ≥80. The luminaire shall be

BIS Registered with isolated type electronic driver in polycarbonate / metal enclosure with input

d MR voltage range of 100 to 265V , THD ≤ 10% & PF ≥ 0.90, 50,000 Hrs LED Life with L70 Criteria. Nos. 18.00 2722.00 48996.00

The LED Driver shall be of same make and made in India for ease of repair and service. The

LED shall be SMD type. Luminaire shall have minimum surge protection of 2.5KV. The luminaire

shall be with following certifications: LM79 & LM80 issued by LED manufacturer along with

Photo Biological Safety Standard. Wipro Cat. Ref. LD06-221XXX-57SMBT

Digitally signed by AKSHIT

Rate as per DSR

Sl.No. DSR Item No. Description Unit Quantity DSR Amount NDSR Amount

Supply, installation, testing and commissioning of 10W Bulkhead delivering minimum system

lumen of 1000 lm & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing & Rim is

Pressure Die Cast Aluminium. The Luminaire shouuld have ingress protection of IP65 and IK

rating of IK08 along with Opal Polycarbonate Diffuser. The operating CCT shall be 5700K with

CRI of ≥80. The luminaire shall be BIS Registered and should have input voltage range of 140 to

280V along with THD ≤ 10% & PF ≥ 0.95. The Luminaire shouuld have a life class of 50,000 Hrs

LED Life with L70 Criteria. Luminaire shall have minimum surge protection of 2.5KV. The

luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacturer along

with Photo Biological Safety Standard. Wipro Cat. Ref. LW07-141-XXX-57-G1

SUPPLY OF CEILING & EXHAUST FANS

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting frame,

and other accessories etc. complete

300 mm sweep (Heavey Duty) Nos 2.00 1653.00 3306.00

TOTAL FOR ELECTRICAL WORKS

Digitally signed by AKSHIT