Loading…
Loading…
Tender Value
₹30.6 L
EMD Value
₹61,100
Closing Date
23 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
BUILDING1
34 conditions · 5 needing a document upload
Check list should be as per the annexure-XXIII as given in the tender document attached. Note: Tenderer's attention is invited to clause 1 of Section VII and other relevant clauses of Section I and II whereby in case of nonsubmission/ non compliance, the tender offer is likely to be rejected.
1.1) Following documents are common for all types of firms i.e. Sole proprietorship, Partnership, Limited Company or JV.
(a)Tender Form (First Sheet) as per 'Annexure-I' (Mandatory)
(b) Firm details as per Annexure-II
(c)Format for Certificate as per proforma given in 'Annexure-III A' (Mandatory)
(d) List of works of similar nature physically completed in all respects in current and last three financial year as per proforma given in 'Annexure-IV'
(e)Work Completion Certificate of works mentioned in para (d) above from the Organizations with whom they worked as per proforma given in 'Annexure-V' as applicable. (Mandatory)
(f)List of works on hand as per proforma given in Annexure-VI
(g)List of plants & Machinery available on hand (own) and proposed to be inducted (own and hired to be given separately) for the subject work in Annexure-VII.
(h)List of Personnel, Organization available on hand and proposed to be engaged for the subject work in Annexure -VIII.
(i) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; whereV= Advertised value of the tender in crores of RupeesN= Number of years prescribed for completion of work for which bids have been invited.The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.The tenderers shall submit requisite information as per Annexure-XIVA, of Standard Tender Document along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(j)Self attested copy of Permanent Account Number (PAN) issued by Income Tax Department.
(k)The tenderer(s) are required to submit the test report of the stone ballast conforming to railways specifications as given in the condition no.7.2.2 of section-VI along with their offer, issued from the approved laboratory as listed in condition no 7.1.1(a) of section-VI in the tender documents. (This item will be applicable only for the tenders of supply of ballast).
(l)Any other document in support of his/their credentials/scheme.
(m)Contractual Receipt of the year on the Letter Head of Chartered /Cost accountant. 'Annexure-IX' (Mandatory)
1.2 In addition to Para 1.1 above certain more documents are to be submitted by tenderers as per status of their firms. These documents are listed below - (Mandatory)
1.2.1For Sole Proprietorship firm a)Affidavit as per 'Annexure - X'. b)Special power of Attorney as per proforma given in 'Annexure-XI' to be submitted by sole proprietor firm duly notarized.(Not required if tender documents are submitted by proprietor himself) (Mandatory)
1.2.2 For Partnership firm a)Self/Notary attested copies of Partnership deed. b)Special Power of Attorney as per proforma given in 'Annexure-XII' to be submitted by Partnership firm. (Not required if one or more partners are authorized in Parternership deed to sign on behalf of the firm.) (d)All other documents in terms of explanatory notes in clause 22 of Standard Tender Document.
1.2.3 For Limited Company a) Copy of Memorandum & Articles of Association of Company. b)Self /Notary attested copy of resolution passed by Board of Directors authorizing its Director/Employee to deal with tender on behalf of company. c) 15.1.1 Attested copy of Notarized Special Power of Attorney including ratification clause duly signed by person authorized by the company vide (b) above as per proforma given in 'Annexure- XIII'. d) A copy of Certificate of Incorporation (Mandatory)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
NOTE: BE IT KNOWN TO THE TENDERER THAT :-
All mandatory documents are required to be submitted by the bidder/tenderer at the time of bidding, in case of nonsubmission/ noncompliance, the tender offer is likely to be rejected.
(a)No post tender submission of documents shall be permitted in respect of item mentioned above. However, only clarification can be called for by Railway in respect of any part / document submitted by the tenderer which shall be responded to by the tenderer within 10 working days of the date of issue of such letter for clarifications, failing which the offer shall be dealt with as per available documents.
Up-gradation of Barrack at Rangia division. (Project Id - 08.04.64.24.3.53.001).
61-ENGG-RNY-2026-27~NFR
61-ENGG-RNY-2026-27
Open
Works - General
6 Months
Kamrup, Assam
₹0
₹61,100
1 Oct 2026
1 Oct 2026
9 Oct 2026
35 items across 2 schedules · ₹8,99,980 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 70 | 1,267.95 | 88,756.5 |
| 2 | Sal wood | cum | .61 | 1,16,520.3 | 71,077.38 |
| 3 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 80.85 | 2,392.65 | 1,93,445.75 |
| 4 | 25 mm dia | Metre | 50 | 525.55 | 26,277.5 |
| 5 | Fixed to steel windows by welding | Kg | 50 | 219.1 | 10,955 |
| 6 | 300x16 mm | Each | 50 | 303.25 | 15,162.5 |
| 7 | 250x10 mm | Each | 50 | 115.15 | 5,757.5 |
| 8 | 125 mm | Each | 50 | 66.25 | 3,312.5 |
| 9 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 120 | 492.7 | 59,124 |
| 10 | Decorative finish (wood grained finish) | Sqm | 20 | 4,713.05 | 94,261 |
| 11 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 500 | 133.7 | 66,850 |
| 12 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. | Sqm | 50 | 1,315.3 | 65,765 |
| 13 | Size of Tile 600x600 mm | Sqm | 70 | 1,553.45 | 1,08,741.5 |
| 14 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 83 | 738.65 | 61,307.95 |
| 15 | Ridges plain (500 - 600mm) | Metre | 100 | 532.35 | 53,235 |
| 16 | 1:4 (1 cement: 4 fine sand) | Sqm | 90 | 347.05 | 31,234.5 |
| 17 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 280 | 262.7 | 73,556 |
| 18 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | Sqm | 900 | 193.7 | 1,74,330 |
| 19 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture | Sqm | 80 | 176.25 | 14,100 |
| 20 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 50 | 170.7 | 8,535 |
| 21 | Old work (one or more coats) | Sqm | 150 | 62.7 | 9,405 |
| 22 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. | Sqm | 150 | 25.15 | 3,772.5 |
| 23 | With cement mortar 1:4 (1 cement : 4 fine sand) | Sqm | 57 | 547.4 | 31,201.8 |
| 24 | Door chowkhats | Each | 10 | 1,782.55 | 17,825.5 |
| 25 | Window chowkhats | Each | 10 | 1,125.15 | 11,251.5 |
| 26 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 1 | 2,434.25 | 2,434.25 |
| 27 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 10 | 6,515.55 | 65,155.5 |
| 28 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 10 | 6,258.75 | 62,587.5 |
| 29 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 14 | 2,648.85 | 37,083.9 |
| 30 | 20 mm nominal dia Pipes | Metre | 100 | 537.6 | 53,760 |
| 31 | 15 mm nominal bore | Each | 20 | 798.95 | 15,979 |
| 32 | 15 mm nominal bore | Each | 20 | 670.45 | 13,409 |
| 33 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 50 | 1,176.8 | 58,840 |
| 34 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. | Sqm | 80 | 688.9 | 55,112 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_correction_Slip_no_11.pdf GCC Correction Slip no 11
ATTACHMENT
Tender Document
ATTACHMENT
GCC_correction_Slip_no_11.pdf
ATTACHMENT
TD_61-ENGG-RNY-2026-27_1.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .