PROVN OF SHED FOR PATIENT WAITING AREA AT MH

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipe lines, manholes etc n exc 10sqm on plan and getting out in soft/loose type of soil including trimming of tree roots in trenches complete all as specified.

M&L PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L PCC 1:2:4 type B2 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&Lfor brick work with sub-class 'B' bricks (using old size bricks), straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M & L for 40mm thick PCC 1:2:4 type B0 as in Damp proof course to horizontal or vertical surfaces including necessary formwork and finishing the surface even and smooth complete all as specified and directed

M&L for hard core of broken stone or boulders of gauge n.exe 63 mm deposited spread and leveled in layers not exe 15cm thick watered and rammed to a true surface complete all as specified.

S & F steel work in tubular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming to IS 1161-1979 graded St-240 complete all as specified and as directed.

S&F rolled mild steel work as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the lenght directed) and similar work conforming to Fe-410 W (Gde E-250) quality A complete all as specified and directed.

S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates of grade Fe-410-W (Gde E-250 ) quality A complete all as specified.

M&L preparation of new steel surface of any description over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed .

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Dune Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories supplied by consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

Removing excavated material to a distance exc 250 m but n exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed.

M & L for preparing new plastered surfaces and applying two coats of cement base paint on wall over a coat of alkali based primer all as specified and as directed

M&L preparation of new steel surface of any description n. exc 10cm in width or girth when un connecting to other painting surface and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L 75mm thick plain cement concrete 1:3:6 type C-2 (using 20mm graded stone aggregates) as in plinth protections, finished even and fair with joints 10 mm wide and in full depth at corners and @ 3m c/c filled with mastic mortar including necessary formwork complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub base to flooring complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-0, using 12.50 mm graded stone aggregate as in floors complete all as specified and directed.

M & L for light shade full body vitrified ceramic tiles 10mm thick (square/rectamgular) polished, area of each tiles n exc. 0.36 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over and incl 15mm thick screed in cement mortar 1:6 complete all as specified and directed.

S&F Powder coated aluminium anodised (minimum thickness of powder coating 50 micron) Three track sliding window frame with shutters (two glazed and one gauged shutter), the size of outer frame three track 100 X 37 X 1.50mm and the section of shutter size 37x 18x 1.2mm and glazing with 5 mm thick transparent glass including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including anodised aluminium grill 0.5mm dia and all necessary fittings complete all as specified and directed. Note : Glass, wire cloth, handle, locking arrangement etc shall be included in quoted rates

S&F anodized aluminium brown/white colour door shutter with frame made of anodized aluminum frame size 101x44x2mm thick and anodized aluminum shutters having bottom rail of size 114x44x2mm, top rail 83x44x2mm, middle rail 85x44x2mm with two numbers of disc/D type handle in each shutter, 200mm size aluminum tower bolts 02 Nos, brass lock 04 levers and key, glazing with 5mm thick tinted glass in upper panel and 12mm thick pre laminated particle board in lower panel including rubber gasket, aluminum beading compete all as directed. Note : Glass, wire cloth, handle, locking arrangement etc shall be included in quoted rates

S&F fixed type anodised aluminium partition in 2 panels with 5mm thick tinted / transparent glass, c/c distance between two vertical member n exc 1.2m and c/c distance vetween 2 horizonatal member n exc 1.3m including rubber gasket, aluminium beading, the vertical member shall be embeded in PCC block 300x300x200mm deep with 150x150mmx6mm thick MS sheet bottom all necessary fittings arrangement complete using aluminium section 65x40x1.5mm thick etc in frame complete all as specified

S&F for 0.63mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed

S&F mild steel flats as in wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 1.25mm thick mild steel sheet eaves gutters, 150mm dia, galvanised class 3, half round with rounded edges incl fixing complete all as specified and directed.

M & L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed .

M&L rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement incl mixing of WPC as per manufacturers instruction complete all as specified and directed. Note : WPC shall be measured and paid seperately

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper with distemper oil emulsion (Ist quality) white or tinted by mechanical means over a coat of primer & over 1mm thick wall care putty to make smooth the undulated surfaces complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates in foundations, including rafts, footings, foundation beam , plinth beams, bases of columns etc. Basement slabs , under reamed piles and mass concrete complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

M&L for RCC M-25 (design mix) (using 20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with flat fair finished surfaces of concrete complete all as specified.

M&L formwork to sides of pillars, posts, struts, piers,columns, and stanchions, etc square, rectangular or polygon finish with flat fair finish surface complete all as specified and directed.

S&F Mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed and specified.

Supply only integral water proofing compound complete all as specified.

M&L for coloured Glazed ceramic tiles (300x450 x 7mm thick), on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

S&F Mild Steel screw bolt (machine made) with hexagonal or square heads at one end and screwed the other end, or screwed both end, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 30cm and dia of bolt exc12 mm n exc 20mm dia of bolt complete all as specified

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 39 above but for one fan point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 39 above but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed.

,---ditto--- all as per item No. 39 above but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc for one 16 Amps socket outlet point controlled by one swith on independent board complete all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm single core, PVC insulated, unsheathed, FRLS multistranded copper conductor cable alongwith one run of 6 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed PVC conduit of 25mm dia ISI marked ivory colour & fitting / fixing accessories of suitable size including making connection as required complete all as specified and directed. NOTE - Two run of 6 sq.mm phase and neutral wire & One run of 6 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length.

,---ditto-- all as per item No. 44 above but two run of 10 Sqmm and one run of 10 Sqmm earth in 25mm dia PVC conduit complete all as specified and directed.

S&F switch modular one way 6 Amps, 240 volts, 1 module complete all as specified and directed.

S&F modular socket 6 Amps, 2/3 pin combined 2 module AC 230 volts complete all as specified and directed.

S&F modular humfree fan regulator 120 watts, 2-module AC 240 Volts complete all as specified and directed.

S&F ceiling rose 3 plates PVC/polycarbonate body complete all as specified and directed.

S&F MCBs Distribution board SPN, 8 ways, powder coated, CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCBs Distribution board tripple pole and neutral (VTPN) 4 ways, powder coated, CRCA steel sheet, suitable for MCCB incomer upto 160amp, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCBs of 'B' curve single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'C' curve SPN 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

,---ditto--- all as per srl item No 53 above but MCB SPN 40 to 63 amps complete all as specified and directed.

S&F MCCB, four pole, 63amp, 415 volt, adjustable type, with breaking capacity 16KA, thermally adjustable between 70 to 100% including 4 spreader link set of same make as that of MCCB including reqd cable connections with copper lugs of suitable size and testing & commisioning complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-20-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F energy efficient recessed mounted LED luminaire suitable for 2'x2' grid ceiling with fullglow fully diffused diffuser and lumen output of 3600 lumens having constant current electronic driver of 36 watt 100 lumen/watt duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable as required complete all as specified and directed.

S & F 20 amp single pole and neutral enclosure with 2 pole and earth metal enclosed plug top in powder coated CRCA steel sheet enclosre recess mounted with chained matel cover for socket out let with and incl one no single pole B curve MCB 16 Amps complete all as specified and directed.

S & F greenline high efficiency LED building light luminiare 35 watt 230V AC outdoor type comprising of pre wired driver, high pressure die cast powder coated aluminium housing heat resistant glass, impact and corrosion resistance incl thermal management in multiple optics, clear acrylic cover and accessories with IP 65/66 protection incl mounting bracket, 1.2m long made out of 40mm dia medium grade GI pipe, bend in shape with and incl 02 Nos MS clamp with nut, bolt, washer etc with and incl two coats of aluminium paint over a coat of red oxide primer on bracket complete all as specified and directed by Engineer-in-charge

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in opal white colour with BLDC fan motor, fan blades, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.5mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected with GI lead wire 4.0mm dia means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire of size 4.0mm upto 7.5 m included in the item).

Supply, install, testing and commissioning of floor standing tower type Air Condition of capacity 2.0 TR, non inverter type, 5 Star Rating, adhering to Specified BEE & EER above 3.2, Environmental Friendly Gas- indoor/outdoor complete with and incl cordless remote control unit and with in -built air ioniser and Plasma filter for better indoor air quality, Evaporator & Condenser Coils and, service wire, copper tubing suction line & liquid line with suitable insulation of nitrite rubber insulation incl outdoor mounting stand complete all as specified and directed.

Supply and fix Voltage stabilizer of capacity 5.0 KVA for automatic operation, copper wound, designed input voltage range 90 volt to 220 volt and output voltage 220 volt to 230 volt with accuracy + 2% variation of voltage range complete with fixing accessories complete all as specified and directed.

Supply, laying, jointing, testing & commissioning LT under ground cable of size (cross sectional area) 50 Sqmm 3.5 core, XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with PVC insulated multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt washers complete all as specfied and directed .

Supply, laying, jointing, testing & commissioning LT under ground cable of size (cross sectional area) 25 Sqmm 3.5 core, XLPE insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with PVC insulated multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt washers complete all as specfied and directed .

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

M & L bricks for protection cover to UG cable (using old size sub class B bricks) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

S & F 100 mm bore GI tubing light grade with all fittings, fixed to wall/ pole / laid in road crossing etc as reqd for protection of cable complete all as specified and directed. Note : Cost of MS clamp, nut bolt, washer and GI fittings etc shall be inclusive in the quoted rates.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.5mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected with galvanised earth strip 32 x 6 mm by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI strip size 32x6 mm upto 7.5 m included in the item).

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

Satish kumar and company (BID ID -3258289)

V S Constructions (BID ID -3261744)

JAGDAMBA CONSTRUCTION COMPANY (BID ID -3260748)

M/S ROHIT CONSTRUCTION (BID ID -3261701)

M.S. ENTERPRISES (BID ID -3260881)

m/s gharu constrution company (BID ID -3262083)

M/S BIKANER CHEMICAL LABORATORIES (BID ID -3262095)

S S CONSTRUCTION COMPANY (BID ID -3262119)

BIG B CONSTRUCTION (BID ID -3261586)

VIJAY KUMAR SHARMA (BID ID -3260876)