SPECIAL REPAIR / REPLACEMENT OF UNSERVICEABLE LT PANEL, STREET LIGHT POLES AND CONNECTED ITEMS AT BASE HOSP AND PROVN OF CERTAIN MINOR WORKS IN THE AREA OF AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Supplying and laying or fixing in replacement, jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 10 sqmm cross sectional area, 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. with and including MS Clamps, nuts , bolts, washers complete all as specified and directed. Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under appropriate items.

All as per Item No 01 above but UG cable of size 10 Sqmm 4 core.

All as per Item No 01 above but UG cable of size 16 Sqmm 4 core.

All as per Item No 01 above but UG cable of size 25 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 35 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 50 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 70 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 95 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 120 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 185 Sqmm 3.5 core.

All as per Item No 01 above but UG cable of size 240 Sqmm 3.5 core.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness shall only be considered for payment

M&L laying well burnt old size bricks, sub class "B" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

Deployment of manpowe / tools for Boring / drilling (Horizontly) manually / mechanically under existing road max 10 M in width) suitable for passing tubing 40 to 100 mm bore complete all as specified and directed by Engineer in Charge

S&F 40 mm dia bore mild steel galvanized iron tubes, 'light grade' with all fitting and laid in trenches or fixed to pole or laid in floors for protection of cable including taking down old pipe complete all as directed

S&F 50 mm dia bore mild steel galvanized iron tubes, 'light grade' with all fitting and laid in trenches or fixed to pole or laid in floors for protection of cable including taking down old pipe complete all as directed

S&F 80 mm dia bore mild steel galvanized iron tubes, 'light grade' with all fitting and laid in trenches or fixed to pole or laid in floors for protection of cable including taking down old pipe complete all as directed

Supply & Fix in replacement twin core, 6 sqmm nominal cross sectional area multistranded aluminium conductor cable, over all PVC sheathed, 1100 Volts grade heavy duty cable PVC insulated and PVC sheathed complete all as specified.

M&L for disconnecting the existing cable from Panel / Pole, preparing the end for jointing Supply and fix cable end termination heat shrinkable joint including sleeves suitable for LT XLPE cable of size 3.5 / 4 core 10 to 16 Sqmm

All as per item Ser No 22 above but size 25 to 50 Sqmm

All as per item Ser No 22 above but size 70 to 120 Sqmm

All as per item Ser No 22 above but size 150 to 185 Sqmm

All as per item Ser No 22 above but size 240 to 300 Sqmm

S&F Offload change over switch, 200 Amps, 415 volts, 4 pole in sheet metal enclosure conforming to IS:13947 (Part-3); IEC:60947-3 with locking facility including all connecting / jointing materials and dismantling of existing change over switch, complete all specified & directed.

S&F Offload change over switch (side operated handle) 400 Amps, 415 volts 4 pole in sheet metal enclosure with interlock door and pad lock facility including dismantling of existing change over switch, complete all specified & directed.

Supply and fix new generation ,energy saving ,environment friendly POST TOP LANTERN fitting, aluminium spun lamdscape luminaires with high power LED 25 watt as light sopurce, making connections including dismentling old light fitting complete all as per specified and directed by the Engr-in-Charge. Make- havells cat part no. RUBYPT25WLED830SSYMTOPC OR EQUIVALANTS MAKE mention under List of Make.

Supply, installing, testing and commissioning in replacement factory made, CPRI approved, powder coated LT Panel board (Dimention of Cubical / enclosure not less than 1500 mm x 1000 mm x 500 mm),cubical compartmentalized, out door type double door, plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with insulated bus bars four pole installed on porcelain / SMC insulator. The panel shall be dust and vermin proof IP-54 class protection and outer shell made of of 3.15 mm CRCA sheet, inner shell made of 2.0 mm thick CRCA MS sheet , 50 x 50 x 6 mm thick MS angle iron frame work, the cubical have bottom channel of size 75 x 40 mm duly powder coated, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :-

(c) Platform of Panel. Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947-II/IS 13947-II (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer

Supply, installing, testing and commissioning in replacement factory made, CPRI approved, powder coated LT Panel board (Dimention of Cubical / enclosure not less than 1500 mm x 1000 mm x 500 mm),cubical compartmentalized, out door type double door, plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with insulated bus bars four pole installed on porcelain / SMC insulator. The panel shall be dust and vermin proof IP-54 class protection and outer shell made of of 3.15 mm CRCA sheet, inner shell made of 2.0 mm thick CRCA MS sheet , 50 x 50 x 6 mm thick MS angle iron frame work, the cubical have bottom channel of size 75 x 40 mm duly powder coated, front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :-

(c) Platform of Panel. Platform for the panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947-II/IS 13947-II (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer

Supply and errection in replacement of 07 mtr long continuously tapered hot dip galvanised Octagonal cross sectional pole with single dipping method having bottom 130 mm A/F and top 70 mm A/F 3 mm thick confirming to ASTM A 572 Gr with yield 450 mpa cut and folded to form an octagonal section and welded in accordance with AWS for wind loading as per IS 875 part 3 1987, Poles shall be provided with base plate of size 225 x 225 x 12 mm which shall be free from any lamination or incursion with no cutting or welding on the pole after hot dip galvanising with single arm 1000 mm long bracket tilted to 150 degree from horizontal toward vertices suitable for mounting on the octagonal pole, including PCC foundation as per company recommendation including all earthwork complete all as specified and directed.

M&L for renewal of Earthing complete with galvanised mild steel earth plate electrode 600 x 600 x 6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI strip 32 x 6 mm as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS TMT bars 8mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Supply and fixing in replacement of 120 W LED Flood light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens with silicon gasket, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant.IP lens for better distribution and toughened glass fixed to housing with screws , street light should have IP 66 protection and impact resistance of IK 07 , Lumen efficiency of LED not less than 110>_ lumen per watt system efficency ,power factor >0.95, THD<10% at Full load CRI> 70% ,Street light should have built in potted Driver THD, open circuit protection , over voltage protection , surge voltage protection 5KV in built & 10KV SPD , and provided with company LOGO ingraved on housing of the Street light complete including taking down of old UNSV fittings all as specified and directed by Engr -in-Charge. Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement . .

Supply and fix in replacement of 90 W LED Street light fitting having epoxy powder coated pressure die cast aluminium housing front cover with polycarbonate lens with silicon gasket, with elegantly designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant, lens for better distribution and toughened glass fixed to housing with screws, street light should have IP 66 protection and impact resistance of IK 07, system lumen efficiency not less than 110 lumen per watt, power factor >0.95, THD<10% at full load CRI> 70%, street light should have built in potted driver, THD, open circuit protection, over voltage protection, surge voltage protection, 10 KV surge protection divice, and provided with company LOGO ingraved on housing of the Street light including taking down of old UNSV fittings all as specified and directed by Engr -in-Charge. Note :-The contractor should take approval of techincal specification of luminaries and driver from department before procurement .

S&F in replacement out door type busbar panel board (Dimention of Cubical / enclosure not less than 600 mm x 450mm x 450mm) made out of 3.15 mm thick MS sheet and MS angle section 50 x 50 x 6 mm factory made CPRI approved suitable for 3 phase 4 wire 415 Volt, 50 Hz, overall powder coated comprising of the following:- (a) FP, Aluminium bus bar 500 Amps insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size “F” class insulators. (b) Incoming MCCB 250 Amps 36 KA, 415 Vots, 50 Hz, FP. – 1 No (c) LED Indicator lamp RYB - 01 set of three.

(d) Platform of Panel. Platform for the busbar panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level. Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947-II/IS 13947-II (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer

S&F pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified.

S&F pre-painted galvaume aluminium zink coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof ridges, fixed with self tapping screws as specified, complete all as specified.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters; purlin where connected to common rafters and running rails and guides for for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde-E-250 quality A).

S&F Mild steel, screw bolt machine made with hexagonal or square heads at one end and screwed the other end with washer and one hexagonal or square nut 5 cm long and 12 mm dia. complete all as specefied.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for seamless ceiling comprising of Gypsum Board 12 mm thick in ceiling fixed with screw or as per manufacturers instructions including necessary jointing and taping, and applying two coat oild bound distemper over one coat primer and 1 mm thick cement base putty complete all as specified and directed by Engr-in-Charge. M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre, intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 Sqm but n exc 4.00 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

S & F solid door frame of size 50mmx47mm made out of 5mm thick PVC sheet prelaminated on single side and plain on other side, reinforced with MS square tube including painting of edges to match with prelaminated sheet, fixed in opening as per specification & drawing

S & F for factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struk

S&F aluminium partition fabricated with aluminium powder coated (minimum thickness of powder coating 50 micron) section for side & top rail of size 101 mm x 44 mm x 2.5 mm for middle rail (horizontal / vertical) of size 101 mm x 44 mm x 2.5 mm, partly glazed with 5 mm thick frosted glass and partly paneled with 3 mm thick aluminium camposit pannel including glazing clip, rubber bead, fixed in position as per stander practice complete all as directed by the Engineer-in-Charge.

S&F in repair for 5.0 mm thick fronsted glass sheet fixed to door / window in semi-circular / polygonal / triangular shape including necessary fixing arrangement such as joining clip, aluminium / SS beading, cleats etc complete all as directed.

M&L plain cement concrete type B1 ( 1:2:4) using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills,steps; seismic and other similar band, copings, covings bed plates, and like including weathering slightly rounded or chamfered angles including necessary formworkk complete

S&F 20 mm mild steel curtain rod with PVC lining out side as approved by GE, as in curtain rods complete all as specified and directed by Engineer-In-Charge.

S&F mild steel powder coated bracket for 20 mm dia curtain rod including PVC chromium plated finials / side holder complete all as specified

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified.

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement mortar 1:4 complete.

M&L for for coloured glazed ceramic tiles in vertical surfaces of size 450 x 300 x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar

M&L for 18 to 20 mm thick granite (of any type) tiles machine cut & machine polished, set & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over and including screed bed 15 mm thick in cement mortor 1:4 complete all as specified and directed. Note : Quoted rate shall be deemed to include cast of screed bed.

Taking down cement plaster of any description on brick or stone masonary wall , etc including racking out joints, hacking for key, scrubbing down with water etc, all as specified.

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles all as directed.

M&L for Brick work with Fly ash brick designation 100 Kg / Sqcm, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, using bricks of size 230 mm x 110 mm x 70 mm confirming to IS 12894, complete all as specified and as directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick in cement and sand mortar 1:6 on brick work or cement concrete surfaces of walls including finishing the surface even and smooth with using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer over and including 2 mm thick cement base wall care putty complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surface of walls and applying two coats exterior emulsion weather coat paint of make Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) over one coat primer with 2 mm thick cement base wall care putty complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level)

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete.

Supply and fix in repair 1000 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

S & F in repairs 20 mm gun metal gate valves ISI marked with iron wheel head screwed both ends for iron pipe and fixed.

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

S&F 20 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

S&F in repair 15 mm size stop valve cast copper alloy chromium plated, fancy type with long shank and cup (concealed type) screwd down, high pressure with crutch or butterfly handle scrwed both ends for iron pipe or union complete.

S&F in repairs for 15 mm size bib taps fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repair 15 mm size pillar taps, cast copper alloy, chromium plated, fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC low level flushing cistern, duel type, valveless, syphonic action type, double push botton, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete complete all as specified.

S&F in repair PVC connection 15 mm size, of length 600 mm, with PTMT nuts complete all as specified and as directed by Engineer-in-Charge

S&F in repair Tubular towel rail stainless steel chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, standerd pedestal, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

S&F in repairs vitreous china urinals, flat back of size 465mm x 355mm x 265 mm, white with grating and union for discharge pipe complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, with PVC clamp all as specified.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, with PVC clamp all as specified.

S&F 110 mm dia PVC (SWR) junction single (single Tee) equal or unequal with access door complete

S&F 75 mm dia PVC (SWR) junction single (single Tee) equal or unequal with access door complete

S&F 110 mm dia PVC (SWR) vent cowl complete.

S&F 110 mm dia PVC (SWR) bends any radius, all as specified.

M&L for aluminium anodised ventilator fixed with refletive type glass, aluminium section weighting 0.55 kg/m incl necessary joining cleats, glazing clips rubber neospeprene at bottom panel and top panel with wire cloth of 0.46mm nominal dia of wire and average with of aperature 1.4mm complete including taking down

M & L for Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Material & Labour for concealed point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn through and including PVC conduit not less than 20 mm dia, including all accessories like bend, tees, junction boxes etc. including 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable of green colour as a earth wire connected to common earth dolly, etc including pressed steel terminal box of suitable size with laminated white top sheet cover of 3.00 mm thick complete.

All as per Item No 87 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per Item No 87 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S & F switch piano flush button single pole one way 5 Amp 240 volt complete all as directed.

S & F switch piano flush button single pole one way 15 Amp 240 volt complete all as directed.

S&F socket outlet flush type multipurpose 2 in 1, 5 pin 6 Amp, 230 volts complete as directed.

S&F socket outlet flush type multipurpose 2 in1, 3 pin 5 and 16 Amp, 230 volts complete as directed.

S&F ceiling rose polycarbonate body surface type three terminal complete as directed.

S&F distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 4 way with 200 Amps rated copper busbar, neutral bar, earth bar, IP 43 protection, single pole and neutral 250 Volts, fixed flush to wall complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

Material & Labour for concealed type sub main wiring with 2 run single core multistranded copper conductor cable, of size 10.00 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 25 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 10.00 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire in green colour, fixed on wall / ceiling, including taking down old sub main wiring complete. Note: (i) 2 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

Material & Labour for concealed type sub main wiring with 2 run single core multistranded copper conductor cable, of size 1.50 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 20 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 1.50 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire in green colour, fixed on wall / ceiling, including taking down old sub main wiring complete. Note: (i) 2 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

Supply & fix / connecting and testing of 3 core, 1.5 Sqmm PVC insulated and PVC round sheathed` copper conductor (flexible ) industurial cable, 1100 Volts conforming to IS 694, for electric connection including providing suitable copper lugs all as specified and directed by Engr-in-charge.

S&F angle / batten type holder insulated body with back plate suitable for batten fittings as directed.

Supply & fix exhaust fan metal body 450 mm sweep, 900 RPM, copper bound motar, AC 230 volts, single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing, writing of MES Nos as approved size of letter complete all as specified and directed.

Supply and fix wall / surface mounting luminaires integrated LED Batten (4 feet) 20 W, 6500 K, 230V , system efficiency not les than 100 lumens / watt, with extruded aluminium housing with frosted PMMA / PC diffuser & integrated electronic driver fixed in position and connecting with ceiling rose complete all as per specified and directed by Engr-in-charge.

S&F 18 watt LED mirror light fitting with builtin electronic driver fixed in position complete.

Supply and installation evaporative desert coolers complete body of size 100 cm x 70 cm x 60 cm (approx) fabricated with 22 gauge plain mild steel galvanised sheet, removable side & back panel fabricated with 24 gauge plain mild steel galvanised sheet, with wood wool pads having nominal air flow capacity of 5000 cfm, having cooler fan motor with 100% copper winding of capacity 280 to 310 watt with 18” metal blade size, and submersible pump of capacity 1.5 m head, complete cooler body powder coated, with all fittings and fixtures as directed by ENG-IN- CHARGE on site complete all as specified and directed.

S&F PVC gang box fitted with and including piano type switch 5 A and socket 5 A, 230 Volts complete with pvc gitties and screws all as specified and as directed.

S&F Framed work for cooler stand fabricated with mild steel angle iron / flat iron confirming to Fe 290, Gde-E-165 including cutting welding and applying two coats synthetic enamel paint over one coat red oxide primer complete.

Eco Creations

Unnati Engineers