PROVISION OF 400 MEN OTM ACCN (FOR YACOOB COY TRG BN-III) AT MEG AND CENTRE BANGALORE

Amount

Lumpsum price worked out by the tenderer for BUILDINGS / STRUCTURES as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the tenderer for SITE CLEARANCE AND DEVELOPMENTS as listed in Schedule ‘A’ Part-II

Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-III

Lumpsum price worked out by the tenderer for INTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-IV

Lumpsum price worked out by the tenderer for ROAD / PATH / CULVERT as listed in Schedule ‘A’ Part-V

Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI

Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VII

Lumpsum price worked out by the tenderer for FENCING AND GATE as listed in Schedule ‘A’ Part-VIII

Lumpsum price worked out by the tenderer for RAIN WATER HARVESTING as listed in Schedule ‘A’ Part-IX

Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-X

Lumpsum price worked out by the tenderer for EXTERNAL ELECTRIC SUPPLY as listed in Schedule ‘A’ Part-XI

Lumpsum price worked out by the tenderer for COOLING APPLIANCES as listed in Schedule ‘A’ Part-XII

Lumpsum price worked out by the tenderer for SOLAR WATER HEATER as listed in Schedule ‘A’ Part-XIII

Lumpsum price worked out by the tenderer for HIGH MAST LIGHTING as listed in Schedule ‘A’ Part-XIV

Lumpsum price worked out by the tenderer for DEMOLITION OF BUILDINGS as listed in Schedule ‘A’ Part-XV

SCHEDULE 'A' PART XVI (D G SET ) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

Supply, installation, testing and commissioning of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire, engine as per IS:10001/ 10002 and Alternator as per IS: 13364, water cooled, diesel engine developing minimum 58 BHP or more at 1500 RPM including AMF control panel for 40 KVA DG Set with fuel tank capacity 100 Ltrs capacity with standard manual control panel and batteries with relay panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy as per latest CPCB norms with suitable emission control device confirming to NGT norms and foundation (height of the foundation should not be less than 45cm from ground level) etc. of capacity 32kW /40 KVA mounted on base frame complete all as per Item No.1 of Schedule 'A' Part XVI (DG Set)

BLANK

SCHEDULE 'A' PART XVII (MECHANICAL LAUNDARY) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

Supply, install, testing and commissioning Washer Extractor of 30 kg capacity, approx dimension 1300mm x 1400mm x 1725mm, high spin, VFD energy drive with microprocessor based control, soft mount, front loading, electric heated, Stainless steel cabinet all as per Model AXE30 of Stefab or techno-commercially equivalent of other specified makes including all accessories and making all necessary electric and water connections as per latest engineering practices complete all as specified and as directed.

Supply, install, testing and commissioning Drying Tumbler of 30 kg capacity, approx dimension 1050mm x 1425mm x 1980mm, VFD energy drive with microprocessor based control, Stainless steel cylinder, electric heated, Reversible all as per Model DRE30 of Stefab or techno-commercially equivalent of other specified makes including all accessories and making all necessary electric and water connections as per latest engineering practices complete all as specified and as directed.

Supply, install, testing and commissioning Flat Bed Drying press approx dimension 1600mm x 1500mm x 1260mm, Head size 1500 x 750 mm Pneumatically operated bed with Centrifugal vaccum Auto timed release, electric heated all as per Model FPE150 of Stefab or techno-commercially equivalent of other specified makes including all accessories and making all necessary electric and Steam/water/air connections as per latest engineering practices complete all as specified and as directed.

Supply, install, testing and commissioning Vaccum finishing table approx dimension 1230mm x 890mm x 1850mm, Table top size 1200 x 750 mm with electric steam iron + Teflon Shoe, Centrifugal suction blower all as per Model VF120 of Stefab or techno-commercially equivalent of other specified makes including all accessories and making all necessary electric and Steam/water/air connections as per latest engineering practices complete all as specified and as directed.

Supply, install, testing and commissioning Steam Generator approx dimension 350mm x 600mm x 870 mm. Electric, Portable and Fully Automatic. Steam Capacity 8 Kg / hr all as per Model No. SE8 of Stefab or techno-commercially equivalent of other specified makes etc. complete all as specified and as directed.

SCHEDULE 'A' PART XVIII (CHIMNEY AND SOLAR POWER PLANT) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

Supply, install, testing and commisioning of kitchen hood made of SS 304 matt finish 1 mm thick wall mounted type with removable grease stop and fixing brackets, oil drain channel of exhaust hood size 7ftx3ftx20 inch including drain collector & connecting with exhaust ducting etc., complete all as specified and as directed.

Supply, install, testing and commisioning of kitchen hood made of SS 304 matt finish 1 mm thick wall mounted type with removable grease stop and fixing brackets, oil drain channel of exhaust hood size 5ftx3ftx20 inch including drain collector & connecting with exhaust ducting complete all as specified and as directed.

Supply, install, testing and commisioning of kitchen hood made of SS 304 matt finish 1 mm thick wall mounted type with removable grease stop and fixing brackets, oil drain channel of exhaust hood size 3ftx3ftx20 inch including drain collector & connecting with exhaust ducting complete all as specified and as directed.

Supply and install removable grase stop filters size 600mm x 500mm x 50mm complete all as specified and as directed.

Supply and install exhaust ducting of size 575x300 mm made of GI sheet 22 SWG including connecting with ceiling mounted exhaust hood up to terrace with MS angle frame 25x25x3mm thick fixing of brackets with nut bolts, gaskets supporting thread rod, channels complete all as specified and as directed.

Supply, install, testing and commissioning exhaust blower of capaity 3 HP, 440V, three phase 1440 RPM incuding starter, connecting with exhaust ducting and suitable electric copper cable connecting with starter complete all as specified and as directed.

Supply and installlation collar damper of size 400x200x150 mm for connecting between duct and exhaust hood made out of GI 20 SWG with air control lever complete all as specified and as directed..

Supply and fix anti vibration bush with MS fabricated stand frame angle of size 50x50x5mm thick for resting blower complete all as specified and as directed.

Supply, install, testing and commissioning Solar Power Plant (Roof top) off - grid type of 5 kw with solar battery system minimum back up of 4 hrs at full load including all accessories like, Solar inverter with batteries, Solar panels. Solar structure, LT power diistribution panel, earthing for complete system, AC cable, DC cable, lightning arrester, junction box etc., completeall as per item No.9 of Sch 'A' Part XVIII (Chimney and Solar Power Plant)

SCHEDULE 'A' PART XVIII (MISCELLANEOUS ITEMS) Note: This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under column 5 signifies this fact only.

INTERNAL ELECTRIC SUPPLY

Supply and Fix 22W (1X4') decorative, 6500K, wall mounted, ultra slim, polycarbonate, LED lighting fixture with high lumen output, environmental friendly, energy efficient with electronic driver complete all as per Cat No.LHEXBTP7IN1S022 of Havells or techno-commercially equivalent of other specified makes with all fixing arrangement etc., complete all as specified and as directed.

Supply and Fix 10W LED smart bright surface and wall mounted LED batten, a reliable and affordable system that delivers up to 40% energy savings complete all as per Cat No. BN021 LED 10S-6500 PSU GRS1 of Philips or techno-commercially equivalent of other specified makes with all attachment & fixing arrangement. etc., complete all as specified and as directed.

Supply and Fix 1 x 40W (4 feet) LED smart bright surface and wall mounted LED batten, a reliable and affordable system that delivers up to 40% energy savings complete all as per Cat No. BN021 LED 40S-6500 PSU GR (4 feet)) of Philips or techno-commercially equivalent of other specified makes with all attachment & fixing arrangement. etc., complete all as specified and as directed.

Supply and Fix LED Adore 9 W B22 CDL Ball Lamp all as per Cat No. LHLDEUEBML8R009 of Havells or techno-commercially equivalent of other specified makes with suitable lamp holder complete all as specified and as directed.

Supply and Fix 8 W LED, 6000K, surface mounted, environment friendly, energy efficient, aesthetically designed, ornamented with rings, moulded body, wall/ ceiling light LED fixture with diffuser to give glare free light all as per Cat No.LHEBKJP7OZ1W008 or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Supply and Fix Telephone socket modular type RJ11 with shutter (01 module) all as per Cat No. 5734 26 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Supply and Fix TV CO-Axial socket outlet modular type, 01 Module all as per Cat No.5734 25 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

S&F MCCB DB VTPN 4 Way, having degree of protection as per IP 43 with metal door (double door) 415 Volts complete with 250 Amps rated copper bus bar with neutral link with provision for MCCB as incomer and 4P MCBs as outgoing and total number of modules equal to 4+12 with blanking plates all as per Cat No.5077 45 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed. Note : MCCB will be measured and paid seperately under relevant items.

S&F MCCB DB VTPN 6 way, having degree of protection as per IP 43 with metal door 415 Volts complete with 250 Amps rated copper bus bar with neutral link with provision for MCCB as incomer and 4P MCBs as outgoing all as per Cat No.5077 46 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed. Note : MCCB will be measured and paid seperately under relevant items.

S&F MCB DB TPN 6 way, having degree of protection as per IP 43 with metal door 415 Volts complete with 100 Amps rated copper bus bar with neutral link with provision for MCB TPN as incomer and 4P MCBs as outgoing all as per Cat No.5076 71 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed. Note : MCB will be measured and paid seperately under relevant items.

S&F MCB DB SPN 8 way, having degree of protection as per IP 43 with metal door 240 Volts complete with 100 Amps rated copper bus bar with neutral link with provision for MCB SPN as incomer and SP MCBs as outgoing all as per Cat No.5076 11 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed. Note : MCB will be measured and paid seperately under relevant items.

Suppy and fix MCB TPN 40 to 63 Amps,415 Volts,10 kA all as per Cat No.4086 83 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Suppy and fix MCB SPN 6 to 32 Amps, 240 Volts,10 kA, all as per Cat No.4086 17 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Suppy and fix MCB SP 6 to 32 Amps, 240 Volts, 10 kA all as per Cat No.4085 95 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Suppy and fix MCCB 63 Amps, 415 Volts, 36 kA braking capacity with Thermal Magnetic protection all as per Cat No.4200 93 of Legrand or techno-commercially equivalent of other specified makes etc., complete all as specified and as directed.

Supply, Installation, testing and commissioning of LT feeder pillar box, factory made, CPRI approved, Indoor type floor mounting with channel iron pedestal frame made out of 2.00 mm thick CRCA sheet steel and MS angle section 40x40x6mm base frame compartmental type, dust proof, free standing, suitable for working on 440 volts 3 phase 50 Hz A C supply, vermin proof, front and rear opening, hinged doors etc powder coated as per seven tank process and IP 43 protection,

cable alley, cable entry hole at the bottom, earth strip 32x6mm , 3 phase and neutral copper bus bar of 400 amps with non adhesive color coded insulation sleeves mounted on insulators, drilled holes on bus bar strips for tapping including nuts bolts and washers, PCC works complete with copper strips of suitable size for connecting MCCB complete and comprising of the following:- (OTM ACCN)

(a)MCCB, 4 pole, 200 Amp with ultimate breaking capacity 36 kA at 415 Volts with thermal magnetic protection - 01 No. (As Incomer from FPB) (b) MCCB, 4 pole, 63 Amp with ultimate breaking capacity Icu-36kA at 415 Volts - 05 No. (c) MCB, single pole, 40 Amp with ultimate breaking capacity Icu-10kA at 240 Volts - 02 Nos.

(d) Digital Ammeter 0 to 400 Amps & 3 Nos of CT's, Class 1.0, 10 VA -1 Set (e) Digital Voltmeter 0-500 V with 7 position.& 2A HRC fuses/ MCB'S- 1set (f) LED phase indication lamps R,Y,B for incomer and out going switches.

Supply, Installation, testing and commissioning of LT feeder pillar box, factory made, CPRI approved, Indoor type floor mounting with channel iron pedestal frame made out of 2.00 mm thick CRCA sheet steel and MS angle section 40x40x6mm base frame compartmental type, dust proof, free standing, suitable for working on 440 volts 3 phase 50 Hz A C supply, vermin proof, front and rear opening, hinged doors etc powder coated as per seven tank process and IP 43 protection,

cable alley, cable entry hole at the bottom, earth strip 32x6mm , 3 phase and neutral copper bus bar of 400 amps with non adhesive color coded insulation sleeves mounted on insulators, drilled holes on bus bar strips for tapping including nuts bolts and washers, PCC works complete with copper strips of suitable size for connecting MCCB complete and comprising of the following:-

(a)MCCB, 4 pole, 320 Amp with ultimate breaking capacity Icu-36 kA at 415 Volts and microprocessor release conforming to IEC 60947 Part-I/IS-13947-Part-I with breaking capacity Ics=Icu at 415 Volts of 36 KA, overload setting 70% to 100%, short circuit setting 5 to 10 times - 01 No. (As Incomer from FPB) (b) MCCB, 4 pole, 50 Amp with ultimate breaking capacity Icu-16kA at 415 Volts - 08 No.

(c) MCCB, 4 pole, 32 Amp with ultimate breaking capacity Icu-16kA at 415 Volts - 02 No. (d) Digital Ammeter 0 to 400 Amps & 3 Nos of CT's, Class 1.0, 10 VA -1 Set (e) Digital Voltmeter 0-500 V with 7 position.& 2A HRC fuses/ MCB'S- 1set (f) LED phase indication lamps R,Y,B for incomer and out going switches.

ROAD / PATH / CULVERT

Material and Labour for 150 mm compacted thick WMM (Wet mix macadam)in two layers of 75 mm thick each with coarse aggregates of granite, trap or basalt, of specified grading, spread, rolled and consolidated to gradient and camber as required using mechanical paver and rolled to uniform smooth surface using power roller 8 to 12 Tonne complete all as specified and as directed.

Material and labour for preparing bituminous surfaces of road and marking centre lines, stop lines, dashes, arrows etc. and the like on roads pavements with hot applied thermo plastic compound 2.5mm thick of white, golden, yellow or black colour as required and confirming to BS 3262-1989 including reflectorising glass bead @ 0.25 Kg/Sqm as per IRC:35(1997) and as per Clause 803 of MORTH specification with special applicator machine fitted with profile shoe, glass beads dispenser propane tank heater and profile shoe heater with heating arrangement up to 160°C, driven by experienced operator all as per manufacturers' instruction etc., complete all as specified and as directed.

Supply and Fix road studs (cat eye) of size 110mm x 128mm x 29.5mm, weight. 248 gms (appx) made out of ABS Engineering plastic, dynamically designed having high impact strength all as per Cat part no art AME 1019 of M/S Automat road safety Pvt Ltd or Dark Eye model No. DA-971-P or equivalent of other specified makes and fitted with 2 Nos. highly reflective reflectors on both sides, fixed with epoxy on bituminous /concrete surfaces as per manufacturer’s instructions complete all as specified and as directed.

Supply and Fix Solar road stud of size 125mm x 125mm and 20mm thick and 55 mm long 40 dia stamp made out of Aluminium Alloy and Polycarbonate (100% water proofing design according to 65) electrically operated and designed to operate automatically in the darkness, powered from rechargeable nickel cadmium battery (1.2V/ 1600MA) with high efficiency Mono rystafie solar panel 2.4V/ 0.3 Watt consisting of with 6 Nos diode bulbs (3 Nos each side) super bright LED with 10,000 to 18,000 mcd all as per Model No. AK 970 of Aktion make or Dhruv of Dark eye or equivalent of other specified make fixed on bituminous/ concrete surfaces with approved epoxy adhesives as per manufacturer's instructions etc., complete all as specified and as directed.

Supply and Fix Polycarbonate round shaped Convex Mirrors of size 1000mm dia, 1.5mm thick, light weight, single piece polycarbonate lense used for greater damage resistance, good finished, ideal for usage Blind Spots, Parking roads, by lanes and crossing roads and Body is made of ABS/Fiber/Plastic red in colour, with adjustable fixing brackets, nuts & bolts all as per model No. FCMO – 100 of Frontier polymers Pvt Ltd or equivalent of other specified makes including Mounting Hardware MS Pipe 80 mm dia of total length 2.4m (i.e. 0.6m in ground and 1.8m above ground) painted with two coats of Ist quality

synthetic enamel of tint black & white paint over a coat of red oxide primer and embedded in PCC 1:3:6 type C2 (using 40 mm graded aggregates) of size 60cm x 60cm x 75cm including necessary earthwork required for post holes complete all as specified and directed. Note: The unit rate quoted shall be deemed to include the cost of excavation in post hole of any kind of soil/hard surface and making good the disturbed surfaces.

S & F retro-reflective sign boards made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D 4956-01 in blue and silver white including subject matter, message, symbol and borders etc as per IRC -67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat & pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable size aluminium alloy rivet @ 20 cm C/C to back support frame of size 2.0m x 1.5 m of stainless steel (grade 304) of dia 25mm, mounted and fixed with 2 Nos of 40 mm dia SS (grade 304) vertical post of total length 3.5 m (i.e 0.60m in ground and 2.90m above ground) embedded in PCC 1:3:6 type C2 (using 40 mm graded stone aggregates) of size 0.6m x 0.6m including necessary earthwork required for post holes complete all as specified and as directed.

SEWAGE DISPOSAL

Supply and laying 150mm internal dia DWC HDPE SN-8 pipes confirming to IS 14930 part-2 / IS 16025 Part-24, laying including all necessary specials, cutting and jointing as specified and as directed.

EXTERNAL WATER SUPPLY

Supply, install, test and commission of Centrifugal electrically driven self priming monoblock pump set with cast iron impeller capable of pumping 536 LPM at 30 Mtr head, squirrel cage TEFC induction motor 3 phase, 415V AC,50 Hz suitable for delivery 536 LPM at 30 Mtr head coupled on common base chanel including necessary PCC foundarion works, nuts and bolts, copper cable from starter to motor through PVC flexible pipe , suitable size of suction pipe not less than 20 feet or as reqd at site , air release valve, foot valve on suction side complete all as directed and specified

Supply, lay and testing ductile iron pipes with spigot and socket ends cast calss K-7 confirming to IS 8329 with inside surface of centrifugally cast cement mortar lined suitable for rubber/lead joint 100 mm dia bore including for laying level or to falls , in trenches , on the ground or on supports above ground level complete all as specified.

Construction of valve chamber of internal size 900 x 900 x 900mm including necessary earth work excavation, PCC 1:4:8 in foundation type D2 using 40mm graded stone aggregate, brick wall in CM 1:4 using old size bricks, PCC 1:2:4 type B1 for coping, 15mm thick rendering in CM 1:4 including provision of MS sheet cover 3.0mm thick with MS angle frame 40 x 40 x 6mm all round and at diagonals of size 40 x 40 x 6mm and also MS plate welded to MS angle as shown in drawing, embedded in concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer etc, complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Supply, lay / spread in trenches riddled earth as specified in IS:1255 for cushioning of cable to the full width of excavated trench, 8cm thick before laying cable and 15cm thick above the cable, gently punned down, stretching and testing of cable on transformer yard etc., complete all as specified and as directed. Note : Punned thickness will only be considered for payment.

Material and labour for M-Sand filling on the level ground surface in Sub-Stations in layers not exc.15cm thick including watering and consolidation etc. complete all as specified and as directed.

Material and labour for Brick platform of size 2m x 2m x 1.5 m in cement mortar 1:6 with PCC foundation 1:4:8 type D-2 using 40 mm graded stone aggregate, PCC 1:2:4, type B-1 using 20 mm graded stone aggregate, 20 cm thick coping over brick work, plastering to exposed surfaces of brick work with cement mortar 1:4, 15mm thick, including two Nos GI tubing, light grade, 100 mm dia, of required length embedded in brick wall on LT side for drawing LT underground cable etc., complete all as specified and as directed. Note: Cost of Earthwork excavation, Returning filling in, removal of soil shall be deemed to include in the unit rate quoted.

Material and labour for 25mm GI pipe light grade bracket not exc. 1.5mtr length for fixing of street light on pole. etc., complete all as specified and as directed.

Supply and fix FRP pole box of size 200X181x98mm with all accessories complete with connector and Mcb SP 6 Amps for street light. etc., complete all as specified and as directed.

(i) Aluminium bus bar 3 phase & neutral of capacity 1000 Amps (ii) MCCB 4 pole 630 Amps 35KA, - 01 No (INCOMING) (iii) MCCB 4 pole 320 amps 25KA, - 01 No (OUTGOING) (iv) MCCB 4 pole 200 Amps 25 KA - 02 No (Outgoing) (v) MCCB 4 pole 63 Amps 16 KA - 01 No (Outgoing)

(vi) MCB TPN 32 Amps 16 KA - 04 No (Outgoing) (vii) MCB SPN 10 Amps 10 KA - 01 No (Outgoing) (viii) Multifunction meter - 01 No (ix) LED phase indication lamp for 3 phase- 01 Set (x) Time Switch 415 V three phase

S&F cable route indicator Oval shape 200x150x6mm cast iron fixed on 25x25xx6mm angle iron incuding marking of HT/LT UG Cable duly painted and grouted in PCC

Supply, fix, test and commissioning of compact, Aesthetic, Ecofriendly and Modern integrated solar street light 60W, 24V, 6300 Lumen in extruded aluminium construction with built-in SCC, high efficient monocrystalline Silicon Photo Voltaic panel 250 Wp (2x125wp), Maximum Power Point Tracking (MPPT) charge controler, 2 days backup, Low Maintenance Lead Acid (LMLA) battery 150 Ah, Hot Dip Galvanized Tubular (HDGT) Pole 7.0metre Octogonal shape above ground level etc., all as per Cat No.60 W Solar SLS of Havells or techno-commercially equivalent of other specified make including charge controller with dusk down sensor complete all as specified and as directed

M&L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure etc., complete all as specified and as directed.

COOLING APPLIANCES AND DESERT COOLER

Supply and fix voltage stabilizers for automatic operation single phase naturally air cooled indoor type and design for input variation between 170 volts to 250 volts with out put voltage stabilizer at 230 volts with accuracy of ± 2.5% and of capacity 1.0 KVA complete all as specified and as directed.

Supply, install, testing and commissioning of Refrigerator, electric driven, single phase, 230 volt AC, 50 Hz, Frost free, Double door, Energy Efficient BEE 3 Star rated of capacity 310/311 litres of LG Model M322RPZL or techno commercially equivalent of other specified makes complete all as specified and as directed.

GOPAL TEKNOCON PRIVATE LIMITED

SOOD ASSOCIATES PVT LTD

AFSON ENGINEERS & CONTRACTORS

Sukhdevraj Sharma Engineers & Contractors Pvt Ltd

C R R CONSTRUCTIONS

MANGLA AMIT BUILDERS PVT LTD

SREEKRISHNACONSTRUCTIONS

KCP INFRA LIMITED