DEVELOPMENT AND BEAUTIFICATION WORK SANGANER STADIUM

Amount

Providing and fixing of kids play zone Including diffrerent types of outdoor playground equipments

Providing and fixing of Children Multiplay system safe play area •6mtr x 4.5mtr. The Height of equigrneot shall be about 3 me with canopy. The whole unit shall have following parts (1) 2 nos. straight side which have 2.4 mtr Engg and width 0.6 mtr and made up of FRP with 5 mm thickness over all. includlng arrangments of 2 nos. stairs of Ms pipe and flats pies with paint, welding, molding finishing work. (2) square deck platform should be made by 14 gage crg sheet with FRP non skid lamination and connected leg support pipe should be made by 60mm IDGI pipe with proper fitting. {3) FRP canopy filted on the platform and made up of fiber glass reinforced plastic with 3mm FRP thick ness withn 20mm IDGI pipe (4) Small Bridge climber shal be made by 25 mm IDGI pipe and properly connected with 1 no of single seater swing for 1 child. all the s harp edgs and corner property grnded to give smeoth finished. The powder coating (Oven Baked) Done on the pipes extend the life of equipments . and install by C C. Baan system shall be suitable for age bit of 3 to 12.

Providing and fixing of FRP made wave slide having safe play area about 4.6mtr x 0.9 mtr. The wave slide required total area 3.6 mlr x 0.6 rntr. Platform height shall be 1.8 rntr from ground Ievel connected with leg support 60mm IDGI pipe and ladder should be made by steel frame rectangular square pie 50mm x 25rnm. for safely purpose railing should be made by 25mm IDGI pipe Total FRP slide length shall be 3 mtr. with 5mm thickness overall both side finishing work. All The sharp edges and corners ara property grinded to give smooth finishing .The Pipes and components are powder coated on surfaces. Slide should be made in a single moulded piece having wave shape thare shall be no any joint in tha slide. FRP components should be palnt and finished.complete set as per direction and satisfaction of engineer in charge

POMMEL HORSE Providing and fixing of Pommel Horse of size not less than 2150mm (Length) x 800mm (Width) x 800mm. (Height), to enhance the flexibility of lower limbs, waist and abdomen. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast Ø250 mm & 10mm thick. The handle frame be minimum of 32NB shall be made from "C" Class G.I. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 8. (The cement concrete and excavation work shall be paid separately)

Supply and fixing decorative fibre benches. Which is made by cast iron and FRP sheet plate. Bench length 5 feet back height 2'5" front height 16" depth 15" and bench leg is made by cast iron. Including bench leg earth work and concrete foundation M-15 grade including all material and labour charges.

Providing and fixing of double seater swing having safe play area- 4mtr x 2.5mtr. The swing required total area about 3 mtr x 1.5 mtr. And height shall be 2.4 mtr. From ground level top bar of swing is made by 60mm IDGI pipe 16 gauge and 4 nos of leg support pipe should be made of 60 mm IDGI pipe 16 gauge. Top bar shall be attached with 2 nos of alloy steel coating bearing with GI chain. Seating arrangement of swing is made up of 9mm thick FRP sheet with proper finshing work. bearing should be covered by specially desing nylon clamp. the pure polyester powder coadting done on the pipes to extend the life of equipments.

SITC of multi seater see saw for which required safe play area shall be about 4mtrx1.5mtr the height of the equipment shall be about - 0.8mtr. The Multi seater see saw comprorises of 4 nos. FRP seats having thickness 4mm with proper finishing and paint finished work.The leaver consists of 25mm IDGI pipe and 80mm IDGI powder coated pipe. The stand for equipment is made of 50mm IDGI pipe with powder coating on complete surface.

Providing and fixing of Praclain mosaic tiles of 50mmX50mmX8mm size manufactured by Cefino, Coral or Pearls and equapproved shade & design with required adhesive over bad of 15 mm thick cement sand mortar 1:3 inclusive nicely finished joints (thickness of joints shall not be more than 1.5 mm) using water proof joints filter (as recommended by manufacturer) & finished with flush pointing in white cement mixed with pigment to match the shade of tiles etc. complete as directed by Engineer in Charge.

Providing and fixing of Round fountain size of 3 M diameter,Water leveling & compactation PCC of M10 grade Thickness of PCC 150mm,RCC of M15 grade of fountain, civil work with two layers in bitween would be plant and made of granite to match the theme and Tiles/marble would be used as base material as complete in all respect, as per direction of Engineer Incharge SITC of Fountain with nozzle and RGB light Description of complete system as under, 4'' dia F.r.P Fibre flout with S 314 pump stand SITC of Three stage Nozzle body brass with complete set head range 20-30 meter,flow rate 4.45 to 2.1 liter /per sec, Inlet/outlet : 50x40 (2''x1.5'') make irlosker/crompton/CRI. 10 mtr led strip light , 8 under water focus light including all electtrical accessories and wiring with all civil work as per direction of engineer in charge ( Drawing attached)

Providing and fixing full way valve (IS: 778 mark) or wheel valve of approved make gun metal 50 MM

Providing and fixing of G.I. Pipes (External Work) with G. I. Fittings (IS: 1239 Mark) including trenching & refilling earth etc. 50 mm dia nominal bore

LIGHTS

SITC of IP 65 protected LED underwater lighting system manufactured by ISO 9001:2008 certified company with di cast housing 55 watt, 220 V AC LED lamps with dynamic color changing capability avilable in quick connecting cable courpled with various mounting accessories, Ability to create 16.7 million uniform, smooth and brilliant colors with out revealing any lamp image. Gland Shall be IP68, including connections with 2.5 sq mm. copper conductor cable etc. as reqd. Luminaries shall have stainless steel AISI 304 top Ring with chrome plated and housing and totally protected fused epoxy polyester coating on all surfaces. The wall thickness of Luminaries not less than 5 mm. All externál nuts bolt and studs of AISI 304 standard stainless steel with high quality elastomer gasket and a aclric glass. Waterproof luminaries shall be waterproof when fully immersed in water per rating IP 65.

SITC of IP 68 protected LED underwater lighting system manufactured by ISO 9001:2015 certified company Ripples/Premier/Family Fountains make with di cast housing 9x 3W, 12V DC LED lamps with dynamic color changing capability avilable in quick connecting cable courpled with various mounting accessories, Ability to create 16.7 million uniform, smooth and brilliant colors with out revealing any lamp image. Gland Shall be 1168, includia connections with 2.5 sq mm. copper conductor cable etc. as reqd. Luminaries shall have stainless steel A151 304 top Ring with chrome plated and housing and totally protected by fused epoxy polyester coating on all surfaces. The wall thickness of Luminaries not less than 5 mm. All external nuts bolt and studs of AISI 304 standard stainless steel with high quality elastomer gasket and a aclric glass. Waterproof luminaries shall be waterproof when fully immersed in water per rating IP68 and shall have been tested and certified as such by a Govt. of India Test Laboratory.

PUMP SETS

Designing, supply erection, commissioning and testing of 10 HP Monoblock submersible pump of Kirlosker make AC. Three phase 380/440 Volt, 50 cycle, supply with foundation bolt, suction stainless steel mesh cover. as per instruction of engineer in charge.

CONTROL PANEL

Supply of Electric panel for 2x10HP panel comprises of a sheet metal enclosure with hinged front door, back-wall mounting type with provision for incoming & outgoing cable entry, main MCCB, overload relays, contactors, overload tripping etc. L&T/ Schneider make, start stop push button switch & indication lamps etc. complete with internal wiring Lighting system shall be connected by a separate switch and fuse but shall not be energized unless pumps are first switched on. Electric panels protected against dust and jets of water per rating IP-55 Tested and certified by Govt. of india Test Lab. Electrical panel will be at a distance of as per site condition duly tested Supply and fixing of 7.5HP panel box for above pumps of steel sheet enclosure with front door stand mounting Hut type outdoor panel with detachable bottotn plate with provision for incoming & outgoing cable, red oxide under coat and paint finish. Panel comprising 1 No main incoming 2 pole MCB, three nos. back up HRC fuse for pump circuit, Contactors unit with overload relay, start stop push button switch Contactors unit with overload relay, all accessories must be or Cat. I duly tested, as per instruction of engineer in charge

LED LIGHT CONTROLLER

Supply and fixing of control voltage driver (CVD) for LED lights (12 volt) Premier/Family Fountain make complete as required.

CABLE

SITC of flexible cables for lights 1.5sqmm 4core. Make finolex/polycab.

SITC of flexible cables for Pump 4sqmm 3core. Make finolex/ polycab.

Installation of exercise equipment/machines

SURFING BOARD Providing and fixing of Surfing Board of size not less than 1000mm (Length) x 600mm (Width) x 1400mm (Height), to build up the muscle groups of the waist, enhance the body coordination and flexibility. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast Ø250 mm & 10mm thick. The footrests shall be made from high quality fiber reinforced plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/ Berger/Nerolac with minimum 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 1.(The cement concrete and excavation work shall be paid separately).

CROSS TRAINER Providing and fixing of Cross trainer of size not less than 1320mm (Length) x 600mm (Width) x 1750mm. (Height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The Handle Frame shall be made up of atleast 25NB “C” Class G.I. Pipe. The footrests shall be made from Aluminum casting material of size not less than 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 Micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 2. (The cement concrete andexcavation work shall be paid separately).

THAI-CHI SPINNER (2 WHEEL) Providing and fixing of Thi-Chi spinner (2 Wheel) of size not less than 700mm (Length) x 1000mm (Width) x 1280mm (Height), to increase mobility of shoulder -elbow and hip-knee. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast Ø250 mm & 10mm thick. High tensile S.S. nut bolts shall be used for assembly. The powder coating shall be done with pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 3. (The cement concrete and excavation work shall be paid separately)

SEATED PULLER Providing and fixing of Seated Puller of size not less than 1900mm (Length) x 740mm (Width) x 1920mm. (Height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio- pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 250 mm & 10mm thick. The handle frame shall be minimum of 32NB "C" class G.I. pipe. The seat frame minimum of 32NB "C" class G.I. pipe, Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 4. (The cement concrete and excavation work shall be paid separately).

LEG PRESS Providing and fixing of Leg Press of size not less than 1840mm (Length) x 360mm (Width) x 1560mm. (Height), to build up the muscles of thigh and enhance the strength of waist. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast 0250 mm & 10mm thick. The Sleeve frame minimum of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve should be disassembled from main frame. The footrests shall be made from casted Aluminum material, having sizes minimum of 130mm X 310mm X 5mm thick. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/Berger/ Nerolac with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 5. (The cement concrete and excavation work shall be paid separately)

POMMEL HORSE Providing and fixing of Pommel Horse of size not less than 2150mm (Length) x 800mm (Width) x 800mm. (Height), to enhance the flexibility of lower limbs, waist and abdomen. The main structure frame shall be made from G.I. pipe minimum of 80NB "C" class welded with M.S. round base plate atleast Ø250 mm & 10mm thick. The handle frame be minimum of 32NB shall be made from "C" Class G.I. pipe. Closing Caps shall be made up of high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness, complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fullfil the functional requirement. The indicative Design/Photo is as per enclosed Photo no. 8. (The cement concrete and excavation work shall be paid separately)

m/s harinarayan agarwal

M/S J.K. Enterprises

M/S Niraniya Construction Co

M/S J.K. Enterprises