Special repair to bldg No P-01 CRE Office (Stn Cell) and Provn of hardstanding in single living accn (Bldg No P/1) and front side office bldg of Sig Sec of HQ K and K Sub Area under GE(South) Bangalore

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Removing building materials to a distance of exc. 1.0 Km but not exc. 5.0 Km (1 Metric tonne = 1 Load and One Cum = 1735 Kgs) out side MD Land Complete all as directed.

M &L providing cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, stringcourses lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates,kerbs incl weathering slightly rounded or chamfered angles and throating as directed.

Removing Existing water proofing treatment, including bedding concrete etc complete, cleaning the surfaces with wire brushes, removing dust, foreign material ,scrubbing down with water and rubbish off the same beyond the Defence land.

Material and labour for PCC 1:2:4 type B0(using 12.5mm graded stone aggregate) for but on roof slab as required to fill up the undulations to maintain smooth slope (avg thickness 40 mm.) complete all as specified.

Material and labour for rendering 15mm thick in CM 1:4 on roof surfaces mixed with WPC finished even and smooth without using extra cement. Note: WP compound will be measured and paid seperately.

Supply only integral water proofing compound.

Material and labour for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) for filleting and benching, slightly rounded or chamfered on edges complete all as specified and directed.

M&L preparation of old steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enemel paint complete all as specified and directed .

Dismantling of old Ceiling/boarding, any description, fixed in any position with nails complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for cleaning the plastered/concrete surfaces with wire brushes and applying water proofing treatment as under: (a) Apply bitumen primer at the rate of 0.27 litre per Sqm as per IS 3384-1986 and bonding bitumen of VG-10 @1.20 Kg per Sqm. (b) APP modified water proofing memebrane as per IS 16540/16532-2017, 3mm thick and weighing not less than 3.50 kg per Sqm reinforce polyster/HMHDPE matt black finish over compatible primer/bonding bitumen and finish the top surface with bituminus aluminium paint @0.10 Ltr per Sqm complete all as specified.

S&F anodised aluminium snap grid frame work for false ceiling, size of grid 605x605mm, complete all as specified and directed.

Hangers 4 mm dia G.I (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified and directed.

M&L 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timer/GI/ Aluminium framework with screws as in ceiling complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, incl ridges etc complete all as speicifed and as direceted.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

M & L Roof trusses Fe-410W (Gde-E-250) qualityB (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing debrits out side the MD land complete all as specified and directed.

S&F coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F coloured Glazed ceramic tiles in vertical surface 450x300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in block masonry with solid blocks, exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc, incl raking out joints, hacking for key scrubbing down with water, etc. complete all as specified and directed.

M&L rendering 15mm thick in Cm 1:6 on bricksurfaces finished even and smooth without using extra cement all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces mixed with integral water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. (Note :- Water proofing compound shall be measured and paid for separately as supply only under relevant item of this schedule).

M&L preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion white or tint with priming platered and other surfaces incl 1 mm thick wall care putty on plastered surface complete all as specified.

M&L for preparation ol new plastered surfaces of walls Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for preparation of old distempered surfaces of walls and applying one coat of Oil emulsion distemper including stopping of nail holes, filling of cracks, etc and cleaning all window panes from splashes / droppings, complete all as specified and directed.

M&L for preparation of old distempered surfaces of ceiling and applying one coat of oil bound distemper all as including cleaning splashes of distmeper on floor/objects etc complete all as specified and directed.

M&L for Preparation of Old surfaces of wall and Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 Sqm complete all as specified and directed.

Taking down Shutters of any description exc 1 sq. m each complete all as specified and directed.

S&F second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F Powder Coated aluminium frame for, frame work, partions doors, windows, ventilators and aluminium grills for windows etc, with one or more rebates icludig joinning cleat for rebates including joining cleats for fixing etc, profile thickness 1.2mm, complete all as specified and directed.

S&F Powder Coated aluminium Door shutters, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips, rubber packing, handle 02 Nos in each door, hinges Powder coated aluminium spap beading, screws etc, profile thickness 1.2mm, complete all as specified.

S&F Factory made second class hard wood 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F solid PVC door frame at size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixed in opening as per specification and drawings complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side colour PVC shet to be fitted in the M.S frame selded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement fixed to frame, all as per specification & drawing complete all as specified and directed.

S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified.

S&F stainless steel 100 mm butt hinges for doors complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodized complete all as specified.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring complete all as specified.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples complete all as specified.

M&L preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar 1:6, complete all as specified and directed.

M&L Making good under cills or over arches, lintels and bressummers. including allpinning when necessary in ncement mortar 1:6 complete all as specified and directed.

S&F in repairs 100 mm long Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all specified and directed.

S&F in repairs 150 mm size extruded aluminium alloy handles fabricated type anodized complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for Reinforced cement concrete nominal mix type B1 1:2:4 (20 mm graded crushed stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surface complete all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Reinforced cement concrete nominal mix type B1 1:2:4 (20 mm graded crushed stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surface complete all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5 mm dia & over upto 10 mm as in stirrups, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F in repairs plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed.

S&F in repairs brass chromium plated grating 125 mm dia circular with centre hole/ without hole of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified.

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float including flush pipe, handle, bracket PVC short bend etc. complete all as specified and directed.

S&F in repair PVC flush pipe 32 mm bore high density for low level flushing cistern including all joints, washers suitable for WC/EWC complete all as specified.

S&F in repairs CP Toilet paper holder fancy type 150mm Size with brackets complete all as specified.

M&L in repairs Health Faucet 15mm size, ABS Body, with wall hook and 1 metre stainless steel braided rubber hose pipe complete all as specified .

S&F in repair vitreous china wash hand basin, white, flat back size 550 x 400 mm including one number brass CP waste coupling, waste pipe 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including CI/PVC/Vitreous china 'P' or 'S' trap , 110 mm dia PVC(SWR) WC connector and 75 mm dia pipe required length for Nahani trap along with grating and testing manholes as specified by filling with water complete all as specified and directed .

S&F in repairs 15mm bore bib tap cast copper alloy, chromium plated screwed down, high pressure, with capstan head , screwed down screwed for iron pipe complete all as specified and directed .

S&F in repairs pillar taps, brass, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs stop valves male/female threaded 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with Capston head, screwed both ends for iron/CPVC pipes or for unions complete all as specified and directed .

S&F in repairs angle valves male/female threaded 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with Capston head, screwed both ends for iron/CPVC pipes or for unions complete all as specified and directed.

S&F in repair tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified.

S&F in repair 32 mm dia PVC waste pipe for WHB complete all as specified.

S&F in repairs 75mm dia PVC (SWR) floor/Nahani trap, plain with grating including solvent cement complete.

S&F in repairs PVC connection 15 mm size , 45 cm long with PTMT adopter,check nuts and washer on both sides for cold water complete all as specified and directed.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

M&L Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed .

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft /loose soil.

Removing excavated material exc. 500 m but not exc 1.50 Km and depositing where directed

M&L 100 mm thick cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregates) as in sub base etc complete all as specified and directed

M&L 100 mm thick cement concrete 1:2:4 type B-2 (Using 40mm graded stone aggregates) as in floors/ Hardstanding etc complete all as specified and directed

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L forming Construction joints 30mm deep X 10mm wide filled with sealing compound Grade 'A' complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M & L for point wiring with 1100 Volts grade 1.5 sqmm PVC insulated FRLSH unsheathed cable with multistandred copper conductor conforming to IS: 694:1990 (for Phase, Neutral and and Earth) in and including Non metalic PVC rigid conduit medium grade/ casing caping suitable at site with ISI mark of appropriate size with all accessories laid in wall/ ceiling/floor etc, concealed with GI flush in box/terminal boxes of sutaible size, including front plate for mounting of modular switch/ socket and combined cover plate with fitting screw washer, including cutting chasses in wall/floor/roof for fixing of conduit and flush in box and making good the distributed surfaces matching with existing complete all as specified and as directed for following- One light/ Bell/ fan point controlled by one switch

All as per Item No 89 above here in before but for Modular type Socket 6/10 Amp of two module in independent board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 89 above here in before but for Modular type Socket 6/10 Amp of two module on same board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 89 above here in before but for Modular type additional light / fan point on the same switch circuit mounted on same switch board controlled with separate switch, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item no 89 above here in before but with 2.5 sqmm PVC insulated FRLSH unsheathed cable with GI Flush in box for modular switch/ socket 16 Amps of sutaible size as required with front plate for mounting of modular switch/ socket and combined cover plate of as required at site complete all as specified and as directed by Engr-in-Charge.

S&F for modular switch piano, flush type single pole, one way 16 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/16 Amp two way of 230 volts complete all as specified and directed by Engr-In-Charge.

S&F for modular switch piano, flush type single pole, one way 5/6 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/10 Amp of two way point complete all as specified and as deirected by engr in charge

S&F for Modular type fan regulator 1/2 module as reqd, 230 volts complete all as specified and directed by Engr-In-Charge.

M&L ceiling rose surface bakelite 65x50 mm two to three terminals.complete all as specified and as directed by Engr-In-Charge.

S & F of Single pole and neutral enclosure 20Amp, 230V with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 10 KA, 230V complete all as specified and as directed by Engr-In-Charge.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 4 Sqmm, 1100 volts grade (FRLS) and one run of 4 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealedin wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 4 Sqmm cable, one run of 4 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealedin wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

S & F in replacement VTPN DB - Dobule Door made out of CRCA mild steel sheet flushed in wall, TPN 8 way with 200 Amp rated bus bar, 415 volt with PVC MCB blanking plate, stove enamelled for incorporated of MCBs, insulators and MCCB of capacity upto 125 Amps TP/FP etc, complete all as specified and as directed by engineer in charge

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc including taking down old complete all as specified and as directed complete all as specified and as directed by Engr-In-Charge.

Supply and fixing MCCB FP 415 Volts 100 Amps, 16 KA complete all as specifed and directed by Engr-In-Charge.

Supply and fixing MCB SPN 40 Amps, 240 Volts,10 KA complete all as specified and as directed by Engr-In-Charge.

Supply & fixing MCB SP 06-40 Amp, AC, 240 volts, 10 KA complete all as specified and as directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED batten 4feet with extruded aluminium housing and robust construction 20 W system lumen including flexible copper 2 core wire from tube light fitting to ceiling rose required length with all accessories all as specified and directed by Engr-in-Charge.

Supply and fixing surface mounted Mini Mirror light LED batten 2feet with extruded aluminium housing and robust construction 10 W system lumen with all accessories if required flexible copper 2 core wire from fitting to ceiling rose complete all as specified and as directed by Engr-in-Charge. (Make- Bajaj/Havells/Crompton)

S&F in replacement LED recess/surface mounting as reqd 2x2 fittings 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with diffuser glare free light complete with driver, holders & LED lamp of colour as decided suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as derected by Engr-in-Charge

S & F LED flood light 30W made up of pressure die cast aluminium housing wth toughened glass and LEDs as a light source prewired with electronic driver suitable for 30 watts light fitting with IP 65 protection with Surge protection device for protection of LED driver, lumen efficacy of light fitting shall be not less than 100 lm/W. with necessary mounting arrangements colour as per deside at site including taking down old unserviceable light fitting.complete all as specified and directed by Engr-in-charge.

Taking down unserviceable ceiling fan,exhaust fan of any type, size & description from position and refixing to location complete all as specified and as directed by Engr-in Charge.

S&F in replacement ceiling fan motor of 1200 mm sweep complete with rotor,stator,outer body including 3 nos fan blades, down rod and other connected accessories matching with existing complete all as specified and as directed by Engr-in-Charge.

S&F in replacement Exhaust fan motor of 200/250 mm sweep plastic body complete with rotor,stator,outer body including 3 nos fan blades, down rod and other connected accessories matching with existing complete all as specified and as directed by Engr-in-Charge.

M & L earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & as directed by Engr-In-Charge.

M&L for Breaking road, pavement, hard standing, tiles of any type, including excavation of subbase, soil upto the depth of 0.60 mtr and width 0.45 mtr by mechanical means for fault finding in water pipe lines and including making good to the disturbed surfaces matching with existing after rectification of fault including removal of surplus material to nearby dumping point complete all as specified and directed by Engr-In-Charge. Note:(i) Any T&P required for work is deemed to be included in quoted rates. (ii) Tiles, cement concrete etc. required for making good is deemed to be included in quoted rates.

Supply & lay G I tubing light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc all as specified and directed for 50 mm dia Complete all as specified and as directed by Engr-in-Charge.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm x 4 core including taking down unserviceable UG cable complete all as specified and directed by Engr-In-Charge. (Make-Polycab/Havells/Finolex)

Excavation in trenches in soft /loose soil not exceeding 1.5 M wide and not exceeding 1.5 M in depth for laying of UG cables etc and getting out complete all as specified and as directed by Engr-In-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cms in any type of soil complete all as specified and as directed by Engr-In-Charge.

Removing excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 M above the starting point all as directed.

M&L for sand cushioning in trenches for bricks of u/g cable with coarse sand laid dry in trenches with uniform thickness complete all as specified and as directed by Engr-In-Charge.

Supply and lay burnt bricks of sub class 'B' laid dry across in trenches for cable protection all as specified and directed Complete all as specified and as directed by Engr - In - Charge.