REQUEST FOR PROPOSAL FOR DESIGN, SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF SMART STREET LIGHTING AND ICT WORKS FOR ROADS OF SAGAR SMART CITY INCLUDING OPERATION AND MAINTENANCE OF PROJECT FOR 2 YEARS UNDER SMART CITY MISSION

6 Meter Wide Road

SITC of LED FIXTURE on Existing Pole - 55-65W, Power Module LED, 4000K - 6000K, Overall Luminaire Efficacy->=130lm/W ± 5%, Light Pico-Custom - It's body made of Die cast aluminium using pressure die-casting process. Hole for coupling on pipes Ø 60 mm, for lateral installation. Silicone gasket enusures the IP protection. IP Rating - IP 66. Height – 74mm, Length-476mm, Width -194mm, Weight – 1.45Kgs. Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate.Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens cover in PMMA(IK08). Estimated LED Lifetime is L70 @ 50,000 hours minimum. LM80 report from LED manufaturer should be submitted.BIS Safety test report from UL/Intertek lab should be submitted along with BIS Certificate. LM79 report also should be submitted from UL/Intertek lab.Light Fixture Sample should be submitted for approval from concerned engineer-in charge.

Supply & Installation of 6M HEIGHT ARCHITECTURAL SINGLE ARM CONICAL POLE, 6M Height Conical Single Arm pole is made of in combination of conical section made of High tensile MS Sheet(3mm thick) with top dia. 75mm & bottom dia. 140mm. & Bracket made in combination of 76mm dia. (vertical) & 60mm dia. MS pipe (horizontal), to get 500mm arm length. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Minimum ) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Supply & Installation of SINGLE ARM BRACKET, Bracket made of 60mm dia. MS pipe to get 1000mm arm length with suitable clamping arrangement to fix on the existing LT Pole. Entire bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Bracket is hot dip galvanized (60 microns Minimum) for the effective corrosion resistance. Bracket & it's parts are painted in 3 layer coating (Coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Smart Street Lighting Controller A Smart Street Lighting Controller (SLC) with Following Specficiation is integrated with the light fixture through an IP-65 NEMA socket to facilitate the Individual monitoring & control (On/Off,dimming,..) of each light FIxture.Operating Voltage Range-120V AC - 290V AC High Input Voltage ,SLC should be able to withstand 440Vac input for at least 8 hours. Power Consumption should be less than 6W during active mode. SLC should able to measure Ac Voltage, AC Current and Power with Class2 accuracy, Dimming Shall Support 1-10V Dimming. Adequate Surge Protection Shall be given inside the SLC in addition to the surge protection in the light fixture. SLC shall be capable of controlling and Monitoring Single Light. One SLC shall be used for one light fixture. SLC shall have an On Board Temperature Sensor. SLC shall support integration of at least one external sensor which if required shall be intimated at the time of LOA. Photocell shall be provided. Communication shall be through 865Mhz RF mesh network. SLC shall switch on/off the lamps as per photocell or can be over-riden through online software. Time based switching also should be possible through the gateway. Even if there is any failure in communication. Switching capacity shall be for a load of at least 500W @ 230V.SLC shall be able to detect detect Driver faults, Flickering Fault, High Input Voltage Fault, Low Input Voltage Fault, Dimming Fault, SLC Self Diagnostic check, Protections SLC shall have built in feature to protect Driver/Lights from High Voltage/Low Voltage cutoff/cutin. This feature should be programmable.Operating Conditions -20 Deg C to +60 Deg C, Storage Temperature -40 Deg C to +85 deg C. The SLC shall be capable of dimming or switching on/off based on sensor inputs that will come through the gateway. For example, motion sensors may connect wirelessly to the gateway and the SLC shall be capable of performing actions based on the sensor signals.

Smart Street Lighting Gateway A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. Surge protection of atleast 10kV to be provided. GPS should be available in the gateway.

CCMS-Street lighting feeder pillar-20KW Max., 3Phase A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. In addition, to the above, the Gateway shall have a RS232 interface for connecting to the energy meter (DLMS protocol). Energy Meter shall be ISI certified Class 1 Energy Meter. Latching relay should be used for switching the circuit on/off. MCBs should be given for short-circuit protection and wireless reset MCB option should be available. Surge Protection of at least 20kV to be provided. Isolator load break switch of sufficient current rating to be provided for isolating the circuit and bypass switch to be available for switching the circuit on during the daytime for lamp maintenance. GPS should be available in the gateway.

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 10 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 16 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 25 Sq.mm(XLPE)

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 6mm to 16 Sq.mm

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 25 Sq.mm

Laying of one number PVC insluated and PVC sheated power cable of 1.1kV grade of size not exceeding 25 Sq.mm direct in ground including excavation, sand cushioining, protective covering and refilling the pit etc. as required.

Designing & casting with M-20 cement concrete foundation suitable for 9 mtrs. Octagonal poles considering the safe soil bearing capacity at site as 10 T/sqm at 2 mtrs. Depth including excavation, foundation nut bolts in an approved manner.

Gland Size 22mm suitable for cable 2,3, 3½, 4 x 10 Sq.mm or 2x 16 Sq.mm BRASS COMPRESSION GLAND Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete.

Gland size 28mm for 3,4 x 16 Sq.mm BRASS COMPRESSION GLAND Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete.

Gland size 32mm for 2,3, 3½, 4 x 25 Sq.mm OR 2,3, 3½ x 35 Sq.mm OR 2,3 x 50 Sq.mm. BRASS COMPRESSION GLAND Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, Rubber ring complete erected with cable and lead connection etc. as per specification complete.

Supplying and installing Double wall corrugated pipes (DWC) of HDPE ( IS 14930 Part II -marked ) for cable laid under ground with necessary connecting sockets/ couplings,tees of same material and at required depth upto 90cm. below road/ground surface,including excavation, back filling with excavated material with ramming and making the surface good. 50.00mm outside dia.

CIRCUIT WIRING IN EXISTING CONDUIT / PVC CASING CAPPING Supplying and drawing single core PVC insulated cable FR with copper multi strand conductor ISI marked in existing rigid conduit in surface or concealed as per specification. 1.5 Sq mm cable 3 X 1.5 sq mm

Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangment on the top and G.I. watering pipe 20mm dia 2.7 meter long etc. (but without charcoal or coke and salt ) complete as required.

Add Extra for using salt and charcoal / coke for G.I. Plate or Copper plate earth electrode as required including excavation & refilling.

Supplying and laying 25mm X 5mm G.I. strip at 0.5 meter below ground level as strip earth electrode including soldering etc. as required.

Erection of G.I. wire No.8 SWG including binding etc.as required.

Labour charges for fixing 'D' brackets of angle iron 50x50x6mm size on existing pole as required

Laying of underground cable armoured./ unarmoured as per specification in air with approved type of iron clamps complete. 2 / 3 / 4 Core cable upto 16 Sq.mm

Laying of underground cable armoured./ unarmoured as per specification in air with approved type of iron clamps complete. 3 / 3½ / 4 Core cable 25 Sq.mm to 120 Sq.mm

Dismantling poles/street light standards/struts embedded in cement concrete foundation etc. as required.

8 Meter Wide Road

SITC of LED FIXTURE on Existing Pole - 75-85W, Power Module LED, 4000K - 6000K, Overall Luminaire Efficacy->=130lm/W ± 5%, Light Pico-Custom - It's body made of Die cast aluminium using pressure die-casting process. Hole for coupling on pipes Ø 60 mm, for lateral installation. Silicone gasket enusures the IP protection. IP Rating - IP 66. Height – 87mm, Length-567mm, Width -233mm, Weight – 2.35Kgs. Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate.Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens cover in PMMA(IK08) . Estimated LED Lifetime is L70 @ 50,000 hours minimum. LM80 report from LED manufaturer should be submitted.BIS Safety test report from UL/Intertek lab should be submitted along with BIS Certificate. LM79 report also should be submitted from UL/Intertek lab.Light Fixture Sample should be submitted for approval from concerned engineer-in charge.

Supply & Installation of 6M HEIGHT ARCHITECTURAL SINGLE ARM CONICAL POLE, 6M Height Conical Single Arm pole is made of in combination of conical section made of High tensile MS Sheet(3mm thick) with top dia. 75mm & bottom dia. 140mm. & Bracket made in combination of 76mm dia. (vertical) & 60mm dia. MS pipe (horizontal), to get 500mm arm length. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Minimum ) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Supply & Installation of SINGLE ARM BRACKET, Bracket made of 60mm dia. MS pipe to get 1000mm arm length with suitable clamping arrangement to fix on the existing LT Pole. Entire bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Bracket is hot dip galvanized (60 microns Minimum) for the effective corrosion resistance. Bracket & it's parts are painted in 3 layer coating (Coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Smart Street Lighting Controller A Smart Street Lighting Controller (SLC) with Following Specficiation is integrated with the light fixture through an IP-65 NEMA socket to facilitate the Individual monitoring & control (On/Off,dimming,..) of each light FIxture.Operating Voltage Range-120V AC - 290V AC High Input Voltage ,SLC should be able to withstand 440Vac input for at least 8 hours. Power Consumption should be less than 6W during active mode. SLC should able to measure Ac Voltage, AC Current and Power with Class2 accuracy, Dimming Shall Support 1-10V Dimming. Adequate Surge Protection Shall be given inside the SLC in addition to the surge protection in the light fixture. SLC shall be capable of controlling and Monitoring Single Light. One SLC shall be used for one light fixture. SLC shall have an On Board Temperature Sensor. SLC shall support integration of at least one external sensor which if required shall be intimated at the time of LOA. Photocell shall be provided. Communication shall be through 865Mhz RF mesh network. SLC shall switch on/off the lamps as per photocell or can be over-riden through online software. Time based switching also should be possible through the gateway. Even if there is any failure in communication. Switching capacity shall be for a load of at least 500W @ 230V.SLC shall be able to detect detect Driver faults, Flickering Fault, High Input Voltage Fault, Low Input Voltage Fault, Dimming Fault, SLC Self Diagnostic check, Protections SLC shall have built in feature to protect Driver/Lights from High Voltage/Low Voltage cutoff/cutin. This feature should be programmable.Operating Conditions -20 Deg C to +60 Deg C, Storage Temperature -40 Deg C to +85 deg C. The SLC shall be capable of dimming or switching on/off based on sensor inputs that will come through the gateway. For example, motion sensors may connect wirelessly to the gateway and the SLC shall be capable of performing actions based on the sensor signals.

Smart Street Lighting Gateway A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. Surge protection of atleast 10kV to be provided. GPS should be available in the gateway.

CCMS-Street lighting feeder pillar-20KW Max., 3Phase A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. In addition, to the above, the Gateway shall have a RS232 interface for connecting to the energy meter (DLMS protocol). Energy Meter shall be ISI certified Class 1 Energy Meter. Latching relay should be used for switching the circuit on/off. MCBs should be given for short-circuit protection and wireless reset MCB option should be available. Surge Protection of at least 20kV to be provided. Isolator load break switch of sufficient current rating to be provided for isolating the circuit and bypass switch to be available for switching the circuit on during the daytime for lamp maintenance. GPS should be available in the gateway.

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 10 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 16 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 25 Sq.mm(XLPE)

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 6mm to 16 Sq.mm

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 25 Sq.mm

CABLE LAYING Laying of one number PVC insluated and PVC sheated power cable of 1.1kV grade of size not exceeding 25 Sq.mm direct in ground including excavation, sand cushioining, protective covering and refilling the pit etc. as required.

12 Meter Wide Road

SITC of LED FIXTURE on Existing Pole - 190-210W, Power Module LED, 4000K - 6000K, Overall Luminaire Efficacy->=130lm/W ± 5%, Light Pico-Custom - It's body made of Die cast aluminium using pressure die-casting process. Hole for coupling on pipes Ø 60 mm, for lateral installation. Silicone gasket enusures the IP protection. IP Rating - IP 66. Height – 114mm, Length-742mm, Width -337mm, Weight – 5.2Kgs. Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate.Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens cover in PMMA(IK08) . Estimated LED Lifetime is L70 @ 50,000 hours minimum. LM80 report from LED manufaturer should be submitted.BIS Safety test report from UL/Intertek lab should be submitted along with BIS Certificate. LM79 report also should be submitted from UL/Intertek lab.Light Fixture Sample should be submitted for approval from concerned engineer-in charge.

Supply & Installation of 9M HEIGHT ARCHITECTURAL SINGLE ARM CONICAL POLE, 9M Height Conical Single Arm pole is made of in combination of conical section made of High tensile MS Sheet(3mm thick) with top dia. 75mm & bottom dia. 175mm. & Bracket made in combination of 76mm dia. (vertical) & 60mm dia. MS pipe (horizontal),to get 1000mm arm length. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Minimum) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Supply & Installation of SINGLE ARM BRACKET, Bracket made of 60mm dia. MS pipe to get 1000mm arm length with suitable clamping arrangement to fix on the existing LT Pole. Entire bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Bracket is hot dip galvanized (60 microns Minimum) for the effective corrosion resistance. Bracket & it's parts are painted in 3 layer coating (Coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Smart Street Lighting Controller A Smart Street Lighting Controller (SLC) with Following Specficiation is integrated with the light fixture through an IP-65 NEMA socket to facilitate the Individual monitoring & control (On/Off,dimming,..) of each light FIxture.Operating Voltage Range-120V AC - 290V AC High Input Voltage ,SLC should be able to withstand 440Vac input for at least 8 hours. Power Consumption should be less than 6W during active mode. SLC should able to measure Ac Voltage, AC Current and Power with Class2 accuracy, Dimming Shall Support 1-10V Dimming. Adequate Surge Protection Shall be given inside the SLC in addition to the surge protection in the light fixture. SLC shall be capable of controlling and Monitoring Single Light. One SLC shall be used for one light fixture. SLC shall have an On Board Temperature Sensor. SLC shall support integration of at least one external sensor which if required shall be intimated at the time of LOA. Photocell shall be provided. Communication shall be through 865Mhz RF mesh network. SLC shall switch on/off the lamps as per photocell or can be over-riden through online software. Time based switching also should be possible through the gateway. Even if there is any failure in communication. Switching capacity shall be for a load of at least 500W @ 230V.SLC shall be able to detect detect Driver faults, Flickering Fault, High Input Voltage Fault, Low Input Voltage Fault, Dimming Fault, SLC Self Diagnostic check, Protections SLC shall have built in feature to protect Driver/Lights from High Voltage/Low Voltage cutoff/cutin. This feature should be programmable.Operating Conditions -20 Deg C to +60 Deg C, Storage Temperature -40 Deg C to +85 deg C. The SLC shall be capable of dimming or switching on/off based on sensor inputs that will come through the gateway. For example, motion sensors may connect wirelessly to the gateway and the SLC shall be capable of performing actions based on the sensor signals.

Smart Street Lighting Gateway A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. Surge protection of atleast 10kV to be provided. GPS should be available in the gateway.

CCMS-Street lighting feeder pillar-20KW Max., 3Phase A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. In addition, to the above, the Gateway shall have a RS232 interface for connecting to the energy meter (DLMS protocol). Energy Meter shall be ISI certified Class 1 Energy Meter. Latching relay should be used for switching the circuit on/off. MCBs should be given for short-circuit protection and wireless reset MCB option should be available. Surge Protection of at least 20kV to be provided. Isolator load break switch of sufficient current rating to be provided for isolating the circuit and bypass switch to be available for switching the circuit on during the daytime for lamp maintenance. GPS should be available in the gateway.

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 10 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 16 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 25 Sq.mm(XLPE)

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 6mm to 16 Sq.mm

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 25 Sq.mm

CABLE LAYING Laying of one number PVC insluated and PVC sheated power cable of 1.1kV grade of size not exceeding 25 Sq.mm direct in ground including excavation, sand cushioining, protective covering and refilling the pit etc. as required.

18 Meter Wide Road

SITC of LED FIXTURE on Existing Pole - 140-160W, Power Module LED, 4000K - 6000K, Overall Luminaire Efficacy->=130lm/W ± 5%, Light Pico-Custom - It's body made of Die cast aluminium using pressure die-casting process. Hole for coupling on pipes Ø 60 mm, for lateral installation. Silicone gasket enusures the IP protection. IP Rating - IP 66. Height – 101mm, Length-673mm, Width -295mm, Weight – 3.55Kgs. Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate.Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens cover in PMMA(IK08) . Estimated LED Lifetime is L70 @ 50,000 hours minimum. LM80 report from LED manufaturer should be submitted.BIS Safety test report from UL/Intertek lab should be submitted along with BIS Certificate. LM79 report also should be submitted from UL/Intertek lab.Light Fixture Sample should be submitted for approval from concerned engineer-in charge.

Supply & Installation of 9M HEIGHT ARCHITECTURAL TWIN ARM CONICAL POLE, 9M Height Conical Twin Arm pole is made of in combination of conical section made of High tensile MS Sheet(3mm thick) with top dia. 75mm & bottom dia. 175mm. & Bracket made in combination of 76mm dia.(vertical) & 60mm dia. MS pipe(horizontal) to get 1000mm arm length. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Supply & Installation of SINGLE ARM BRACKET, Bracket made of 60mm dia. MS pipe to get 1000mm arm length with suitable clamping arrangement to fix on the existing LT Pole. Entire bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Bracket is hot dip galvanized (60 microns Minimum) for the effective corrosion resistance. Bracket & it's parts are painted in 3 layer coating (Coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint.

Smart Street Lighting Controller A Smart Street Lighting Controller (SLC) with Following Specficiation is integrated with the light fixture through an IP-65 NEMA socket to facilitate the Individual monitoring & control (On/Off,dimming,..) of each light FIxture.Operating Voltage Range-120V AC - 290V AC High Input Voltage ,SLC should be able to withstand 440Vac input for at least 8 hours. Power Consumption should be less than 6W during active mode. SLC should able to measure Ac Voltage, AC Current and Power with Class2 accuracy, Dimming Shall Support 1-10V Dimming. Adequate Surge Protection Shall be given inside the SLC in addition to the surge protection in the light fixture. SLC shall be capable of controlling and Monitoring Single Light. One SLC shall be used for one light fixture. SLC shall have an On Board Temperature Sensor. SLC shall support integration of at least one external sensor which if required shall be intimated at the time of LOA. Photocell shall be provided. Communication shall be through 865Mhz RF mesh network. SLC shall switch on/off the lamps as per photocell or can be over-riden through online software. Time based switching also should be possible through the gateway. Even if there is any failure in communication. Switching capacity shall be for a load of at least 500W @ 230V.SLC shall be able to detect detect Driver faults, Flickering Fault, High Input Voltage Fault, Low Input Voltage Fault, Dimming Fault, SLC Self Diagnostic check, Protections SLC shall have built in feature to protect Driver/Lights from High Voltage/Low Voltage cutoff/cutin. This feature should be programmable.Operating Conditions -20 Deg C to +60 Deg C, Storage Temperature -40 Deg C to +85 deg C. The SLC shall be capable of dimming or switching on/off based on sensor inputs that will come through the gateway. For example, motion sensors may connect wirelessly to the gateway and the SLC shall be capable of performing actions based on the sensor signals.

Smart Street Lighting Gateway A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. Surge protection of atleast 10kV to be provided. GPS should be available in the gateway.

CCMS-Street lighting feeder pillar-20KW Max., 3Phase A Smart Street Lighting gateway with Following Specficiation is provided. Operating Voltage Range - 3 Phase 120Vac-290Vac, Operating Voltage Range - 120V AC - 290V AC,High Input Voltage- SLG should be able to withstand 440Vac input for at least 24 hours,Power Consumption- <6W during active mode. Gateway shall include both 865Mhz RF and GPRS communication. RF communication for connecting to the SLC and motion detectors. GPRS for connecting to the control server. For making the gateway future proof, the Gateway shall also have a Ethernet Port and also equipped with BLE and WiFi. It shall also have provision for connecting 1 Digital I/O and 1 Analog I/O. In addition, to the above, the Gateway shall have a RS232 interface for connecting to the energy meter (DLMS protocol). Energy Meter shall be ISI certified Class 1 Energy Meter. Latching relay should be used for switching the circuit on/off. MCBs should be given for short-circuit protection and wireless reset MCB option should be available. Surge Protection of at least 20kV to be provided. Isolator load break switch of sufficient current rating to be provided for isolating the circuit and bypass switch to be available for switching the circuit on during the daytime for lamp maintenance. GPS should be available in the gateway.

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 10 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 16 Sq.mm.(XLPE)

Supply of XLPE Insulated power cable (conforming IS- 7098 ) 1100 Volt grade/Heavy duty power cable conforming to IS 1554-1100 Volts grade , 2 core /3½ core/4 coreISI MARKED with Alu. Stranded /solid conductor ARMOURED 4 CORE 25 Sq.mm(XLPE)

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 6mm to 16 Sq.mm

LUGS:- Supplying and fixing cramping type Alum. lugs as per I.S.S. Specification suitable for following size of cable with Alu. /Copper solid/stranded conductor evently cramped with high/pressure tool and connected to switch gear/Bus/M.C.C.B./ M.C.B. etc. as required complete. For Conductor Size- 25 Sq.mm

CABLE LAYING Laying of one number PVC insluated and PVC sheated power cable of 1.1kV grade of size not exceeding 25 Sq.mm direct in ground including excavation, sand cushioining, protective covering and refilling the pit etc. as required.

Schnell Energy Equipments Pvt Ltd

Royal Power Turnkey Implements Pvt Ltd

UNITED ENGINEERS PVT LTD