SPL REPAIR TO BLDG NO P-145/01 TO 145/08 OF FD HOSP AT ITARANA MIL STN ALWAR

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed by Engr-in-Charge.

Demolition of cement concrete (un-renforced) in ground floor and paving. exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified & directed by Engr-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store complete all as specified and as directed.

Taking down Chowkatts or frames with shutters without taking off shutters from the frame n. exc 1.5 sq. m each & removing to store complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed.

Taking down cement plaster any description on brick or stone any description complete all as specified & directed by Engr-in-Charge.

Taking up or down 15mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

Dismantling/demolition water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

Dismantling of 75mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling of 100 mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site complete all as specified and as directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified & directed by Engr-in-Charge.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws fixed in repair complete all as specified and as directed.

S&F Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane 3mm in thickness complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified & directed by Engr-in-Charge.

S&F Butt hinges 100mm long medium weight, stainless steel complete all as specified & directed by Engr-in-Charge.

S&F 150mm 'D' type Aluminium handles, type, anodised complete all as specified & directed by Engr-in-Charge.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long complete all as specified and as directed.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engr-in-Charge.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed by Engr-in-Charge.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges steel peg stay etc complete all as specified and as directed including taking down.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified and as directed.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed

S&F Steel windows box type with side hung shutters including projecting type hinges with steel handle 150mm, and steel peg stay, complete with glazing bars, dovetailed or welded & factory made (XW2)M/F) double shutter, openable shutter with glazing bars and other openable shutter without glazing bars, fabricated with members of standard size as shown on drawings including frames complete all as specified and as directed. Note :- The quoted rates shall be deemed of lugs and FI required for fixing wire cloth, Sheet Glass, Grills, iron mongry and guard bars as shown on drg.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed by Engineer-in-charge and all as specified.

Cutting holes in brick/stone walls n. exc. Half brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs stainless steel rod of 25 mm inner dia (in lengths as directed) including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with rawl plug & steel screws on walls/beam, complete all as specified and as directed.

M&L for PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate), 25mm thick, as in floor complete all as specified & directed by Engr-in-Charge.

M&L for Coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed of cement mortar 1:6 complete all as specified and as directed.

Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredmatch over 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-In-Charge.

M&L Vetrified Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical surfaces as dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over incl 15mm thick cement screeding in CM 1:4 complete all as specified and as directed.

M&L 75 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified& directed by Engr-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engr-in-Charge.

M&L for Granite slab 18-20mm thick approved shade as in cooking platform, window cill and the likes, machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete all as specified and as directed.

M&L 16-18mm thick green marble (table rubbed and polished) , skirting jambs, pillars, window cills, cooking platform, staircase treads and the likes; laid over with and including 10mm thick rendering in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, chajjas, & similar suspended work Cement concrete (reinforced) complete all as specified and directed.

M&L RCC (nominal mix) type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L Rendring 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral waterproofing compound complete all as specified and as directed.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and as directed.

Material and labour for prepration over new surface and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance exterior paint emulsion of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm complete all as specified and as directed.

M&L for providing and applying minimum 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and as directed

Material and labour for complete removal of existing treatment from stone wall /plastered wall and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance, exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm over 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and as directed.

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer on walls including 1mm thick wall putty complete all as specified and directed by Engineer-in-Charge.

M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over a coat of primer over and inclucluding 1 mm thick Birla white wall care putty. complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Material and labour preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and as directed.

M & L for brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coats of white wash complete all as specified and as directed by Engr- in - Charge.

All as per description of serial item No.59.00 here-in-above but on ceiling surfaces

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed by Engr-in-Charge.

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified & directed by Engr-in-Charge

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete all as specified & directed by Engr-in-Charge.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 450x300mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed by the Engr-in-charge.

S&F in repair concealed stop wall /angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed by Engr-in-Charge.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed

S&F PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete all as specified and directed

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 3330mm x 160mm complete all as specified and directed

S&F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing surface complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, fixed in repairs, complete all as specified and as directed.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed by the Engr-in-charge.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified and as directed.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as directed by the Engr-in-charge.

S&F for Stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed by Engr-in-Charge. Make : Nirali

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls including removing the old pipes and making good the disturbed surface as per existing complete all as specified & directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as specified and as directed.

S&F PVC (SWR) junction single(Single T) equal or unequal 75mm dia complete all as specified and as directed.

S&F in repair Grating doom 100 mm dia of chromium plated (Minimum weight 25 gms) fixed with cement complete all as specified & directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

Demolition Mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified & directed by Engr-in-Charge.

M&L screed laid 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified & directed by Engr-in-Charge.

M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces over bituminious primer complete all as specified& directed by Engr-in-Charge.

M&L APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven reinforcement/mat (center core) with thermal insulation laid by toarch application method with overlaps 100mm on length side and 100mm on the width side as per manufacture,s instructions with fabric (wt not less than 150 gms/sqm) on primed surface including two coat of refelective silver aluminium paint over APP membrane complete all as specified and as directed.

M&L for 25mm thick Sand cushioning under floors complete all as specified and directed

S&F for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigment laid over sand cushing complete all as specified & directed. Note :- Sand cushioning will measured and paid seperately.

All as per srl item No 98.00 herein before but except tiles (old tiles to be re-used).

M&L PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified& directed by Engr-in-Charge.

M&L Plain cement concrete 1:3:6 type C-1 (using 12.5 mm graded stone aggregate) set in cement mortar 1:4 as in kerb blocks with plain fair faces including chamfered weathering throating etc complete all as specified & directed by Engr-in-Charge.

All as per srl item No 101.00 herein before but except cement concrete Kerb stone (old stone to be re-used) set in CM 1:4.

Precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:6 complete all as specified and as directed.

M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; coller stand ,framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed by Engineer in Charge.

S & F for Pipe Supporting Clamping - Single Pipe of dia 4" (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 4" (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

’ ÜáñS & F for Pipe Supporting Clamping - Single Pipe of dia 3/4" (20 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 3/4" (20 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material GradQty. for one unit: 1. Mono Bracket for 3/4" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 3/4" (20 mm) GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.Ïîï,iw²ÐÒÓ  PQt‚ÃÇ
Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and mak瀠潲景挠浯潰湵⁤ 慷整⁲牰潯⁦潣灭畯摮瀠楡⁤敳数慲汴⥹挠浯汰瑥⁥污獡猠数楣楦摥愠摮愠⁳楤敲瑣摥贮♍⁌㔷洠桴捩䍐⡃㨱㨴⤸琠灹⁥㉄⠠獵湩⁧〴浭朠慲敤⁤瑳湯⁥条牧来瑡⥥愠⁳湩猠扵戠獡⁥潣灭敬整愠汬愠⁳灳捥晩敩⁤…楤敲瑣摥戠⁹湅牧椭⵮桃牡敧

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demelotion of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

Point

Point

All as per srl item No 114.00 but for One ceiling/exhaust fan point controlled by one switch and regulator

All as per srl item No 114.00 but for One 3 pin switch socket outlet, 5 Amp on the same board with other switches.

All as per srl item No 114.00 but for One 3 pin 5 amps switch socket outlet point on independent board.

All as per srl item No 114.00 but for One bell/buzzer point controlled by one bell push.

All as per srl item No 114.00 but for Two way point controlled by two way switch.

All as per srl item No 114.00 but for wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power points for Geyser/AC Points

All as per srl item No 114.00 but for wiring with 2.5 sq.mm multistranded cable and earth wire with copper conductor of size 2.5 sq.mm for 15 amps power point.

All as per srl item No 122.00 but for Modular switch, two way 6 Amp, 1 module

All as per srl item No 122.00 but for Modular bell push 6 Amp, 1 module

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part Stella 20 Watt Galmtube LHEWAJPGPV1D020

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and as directed.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fix wall mounted decorative lamp holder aesthetically designed with elegant frosted glass casing in durable metallic housing inbuilt with bulb holder two pin or Screwed type including insulated body with back plate for angle/batten fitting complete all as specified and as directed. Make/Model : Havells : Floretine WL1LSE27SSLHFOAJD1TZ1I060/Phillips Nerobless/Bajaj/Crompton

Supply and fixing in replacement LED Bulkhead fitting 1 x 10 Watt, complete with Standard LED lighting fixture with extruded polycarbonate housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : <15%. (f) IP rating : IP-65. (g) CCT : Minimum 5400K (h) Polycarbonate housing white coloured (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing in replacement Decorative LED light fitting for mirror adjustable type with high out put diffuser 2 feet, 10 watt 220 V AC including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-In-Charge. Make/Model : Phillips-Vega/Havells- Vanessa Glamtube

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6 mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level connected to GI wire 4mm dia by means of bolts, nuts, check nuts and washers complete including earthing pit, Chemical compound, GI wire 4mm dia up to 7.5 m, 20 mm dia medium grade GI watering pipe, G.I. protection pipe 40mm dia eath pit in PCC 1:2:4 type B-1 using 20 mm graded stone agggragate RCC pit cover including earth work complete all as shown electrical palte No-3 of SSR-2009 (Part-I) NOTE:- The unit rate shall include for excavation & earth work in any type of soil/strata, PCC 1:2:4 type B-I for pit & RCC 1:2:4 type B-I for cover with 8mm dia CTD Bar @150mm C/C both way, funnel with watering pipe 20 mm dia medium grade, 15mm dia light grade GI pipe up to 7.5 mtr long, wiremesh complete all as specified and directed.

S&F sheet metal enclosure incl single pole and neutal with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection all as specified as directed by Engr-in-Charge.

S&F Modular Type AC Box with socket 3 in 1 32 Amps Capacity and complete with 01 single pole 32 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection all as specified as directed by Engr-in-Charge.

Supply and fixing in replacement energy efficient LED street light fitting of 35W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/Roadway luminaire, with driver, including electric connection, fixing the light fitting with new bracket made out of GI tubing light grade 32mm dia, 1.2 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 40x3 mm with suitable nuts and bolts for fixing of bracket including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting with old bracket any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Morethan 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully incl necessary electric connections complete all as directed.