PROVN OF MT GARAGE AT MILITARY HOSPITAL FATEHGARH

Amount

Surface Excavation n.exc (not Exceeding) 30 cm deep and avg 15cm deep and getting Out In soft/loose soil complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep ; for foundation and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas, exc 1.50m but not exc. 3 mt depth. For Footing in soft/loose soil etc cpmplete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed

M&L for treating The backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 Litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 as in foundations, filling and mass-concrete etc complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n exc 25 cm complete all as specified and directed.

Removal of surplus excavated soil to a distance n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point all as specified and directed.

M & L for RCC M-25 design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed.

M & L for Mild steel TMT fe 500D bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

M & L for Mild steel TMT fe 500D bars but 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

M & L for Mild steel TMT fe 500D bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and directed.

M & L for RCC M-25 design mix as in Columns, pillars, piers, posts and struts etc complete all as specified and directed.

M & L for form work as in sides of columns etc complete all as specified and directed.

M&L for Brickwork with flyash bricks, old size straight or curved on plan exc 6m mean radius, built in CM(1:6) .complete all as specified and directed.

M&L for Brickwork with flyash bricks,old size straight or curved on plan to any radius in half brick thick walls, built in cement mortar (1:4) complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded stone agg) as in plinth protection and laid in panels, not more than 3.0 mtr in length, laid to slope incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) , complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings & making joint )

M & L for RCC M-25 design mix in chajjas and the like etc complete all as specified and directed.

M&L for Form Work For Rough Finished Surfaces Of Concrete Measured Flat For Chajja complete all as specified and directed.

M & L for RCC M-25 design mix as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M & L for form work as in roof beams etc complete all as specified and directed.

M & L for RCC- M-25 design Mix in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and complete all as specified and directed.

M & L for RCC- M-25 design Mix in Walls, repair bay walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M & L Formwork to faces of walls, repair bay walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc.; vertical or to batter complete all as specified and directed.

M& L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc all specified and directed.

M & L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces fair finished even and smooth w/o using extra cement complete all as specified and directed.

M & L Rendering 5mm thick in CM (1:3) on fair faces on ceilling concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M & L for Glass dividing strips, 3 mm thick, 38mm of width and inserted in position, conform to design etc complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM 1:4 on fair faces of brick surfaces fair finished the surfaces even and smooth without using extra cement complete all as specified and directed

S & F Steel windows or ventilators,fixed type with glazing bars complete all as specified and directed.

S&F 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty/silicon in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F for 30 mm thick Flush shutter of second class hard wood complete all as specified and directed..

S&F for factory made pressed steel frames for doors/windows of size size 105x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, painted with a shop coat of red oxide primer complete all as specified and directed.

M & L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M&L for preparation of new untreated of wood surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M & L for preparation of new plastered surfaces of wall and applying two coats of OBD over a coat of 1mm thick wall care putty on internal wall surface complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceilling complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of alkali resistant priming paint complete all as specified and as directed.

M&L for 75mm thick Cement concrete type D-2 , 1:4:8 (40 mm graded aggregate) for sub base of flooring complete all as specified and directed

M&L for 40mm thick Cement concrete type B-0 , 1:2:4 (12.5 mm graded aggregate) flooring of using glass dividing strips complete all as specified and directed (Note :Glass strips will be measured and paid seperately )

M&L for 100 mm thick Cement concrete type B-2 , 1:2:4 (40 mm graded aggregate) for base flooring of apron including cutting/making jonits & filling with filler mastic bitumen complete all as specified and directed

M & L PCC 1:5:10 type E-2 as in Sub base flooring of Apron, filling and mass-concrete etc complete all as specified and directed.

M & L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface(Broken stones / boulders) etc complete all as specified and directed.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and directed.

M&L for double charged Vitrified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area of exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in tile grount /white cement/ coloured cement including Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

M&L for double charged Vitrified Ceramic tiles 8-10 mm thick (square/ rectangular) polished, area ofexceeding 0.36 sqm but not exceeding 0.42 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in tile grout/ white cement /coloured cement including Rendering 10mm thick CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement Rendering 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbingand polishing complete all as specified and directed

M&L for 20-25 mm thick machine cut kota stone as in flooring laid over 20 mm thick screed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing complete all as specified and directed

M & L for preparation of newly plastered surfaces of roof including cleaning the surface by using wire brush/pressure hose and applying high performance polyurethane liquid membrane roof casting cold in two coats @ 1.5 Kg/Sqm with spray/brush an elogation of 300% to 700% and tensile strength not less than 3 N/Sqm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5mm as per ASTM C 1305, shore a hardness of not less than 60 as ASTMD 2240. The item includes epoxy prime applied @ 0.15 Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacturer's instruction and sound engineering practice complete all as specified and directed. Note - work shall be executed by authorized applicator of manufacture as per manufacturer's instructions and roof height upto double storey building Guarantte seven years from the certified date of completion .

M & L for providing PCC 1:3:6 type C-1using 20 mm graded stone aggreagte as in padding/levelling course of average thickness not exceding 50 mm including making kerbs at wall and roof junction complete all specified ad as directed

S&F in vitreous china squating pan "Orrisa" patern size 580 mm x 440 mm white with 'P' or 'S' trap front or back inlet with integral foot rest including provision of concrete bedding complete all as specified and directed .

S&F dual mode Low Level Flushing System PVC valveless syphonic action type, 10 ltrs capacity white, with inlet, ball float and handle including brackets complete all as specified and directed.

S&F for Vitreous China Wash Basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets , 32 mm PVC waste pipe, 32 mm PTMT Waste coupling complete all as specified and directed

M&L for Non skid mat finished coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of Each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 15mm thick screed bed or bedding layer of cement mortar (1:6 ) for laying floor finishes complete all as specified and directed .

M&L for Glazed coloured ceramic tiles in vertical surfaces 450mm x 300 mm x 7 mm thick (pattern/digital tiles) set and jointed in neat cement slurry and pointed in white or colour cement to match over plastering 10mm thick on fair faces of brickwork or concrete surfaces in CM (1:4) to receive wall finishes complete all as specified and directed.

S & F of Solid PVC Door frame of size 50mm x 47mm made out of 5mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing.

S & F for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S Frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock and bottom rail on either side & as gap insert for tip rail & bottorm rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/seated to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing.

S & F for rotational moulded polyethylene water storage tanks double layer ISI mark white in colour 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT Float valve complete all as specified and directed.

S&F for SS butt hinges of size 100mm medium weight complete all as specified and directed.

S&F for Aluminium anodised barrel tower bolts of extruded section of 125mm size etc complete all as specified and directed.

S&F for Aluminium handles, cast type anodised of size 125mm etc complete all as specified and directed.

S&F for 300 mm long aluminium anodized, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S & F for PVC ( SWR ) pipe 75 mm dia single socketed in any length with rubber ring joints ,fixed to wall or laid in floor complete all as specified and directed.

S & F PVC ( SWR ) pipe 110 mm dia single socketed in any length with rubber ring joints ,fixed to wall or laid in floor complete all as specified and directed.

S & F for PVC ( SWR ) bend 75 mm complete all as specified and directed.

S & F for PVC ( SWR ) bend 110 mm complete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.all as specified and directed .

M & L for PVC ( SWR ) vent cowl 75 mm complete all as specified and directed.

M&L of 75 mm dia.PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.all as specified and directed .

M&L for Steel water tubing 15 mm bore with screwed & socket joints, medium grade, galvanized (including short lengths) with and including all necessary fittings, such as sockets, bends, elbows,unions, tees, diminishing pieces etc. fixed to walls or ceiling or laid in floors complete all as specified and directed.

M&L for Steel water tubing 20 mm bore with screwed & socket joints, medium grade, galvanized (including short lengths) with and including all necessary fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc.fixed to walls or ceiling or laid in floors complete all as specified and directed.

M&L for 15 mm bore size Bib tap, fancy type, brass chromium plated long body, ISI marked, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore iron pipe and fixed, (weight of one bib tap shall not less than 400 gm each) complete all as specified and directed.

S&F for Gun metal gate valves with iron wheel head, screwed both ends suitable for 20 mm bore GI pipe complete all as specified and directed.

M &L for Stop valve/angle cock, 15mm bore, fancy type, brass chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for brass CP mixer single leaver , fancy type for WHB for mixing hot & cold water screwed down for bore of iron pipe 15mm and fixed complete all as specified and directed.

M&L for PVC connection 15 mm dia and 450 mm long with PTMT nuts at both ends complete all as specified and directed.

S&F for 1.25mm thick Steel rolling shutters, with ball bearing, as specified including top cover anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete gear operated type with bevel gear box and crank handle including locking arrangment with minimum two keys for rolling shutters complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks old size, straight or curved on plan exc 6m mean radius built in cement mortor (1:6) complete all as specified and directed

M & L for PCC bed in (1:3:6) using 40 mm graded stone aggregate as in surface channel of drain including providing necessary formwork complete all as specified and directed

M&L for Pre-cast RCC 1:2:4 Type B-1 (20mm graded aggregate) as in cover slab for drain and similar work complete all as specified and directed

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete,using extra cement including forms,moulds, mitred/stopped ends etc. complete all as specified and directed

Rolling and consolidating formation surfaces in cutting with vibratory power roller exc 8 to 12 ton over above ,complete all as specified and direcetd

M&L for soling (or sub base) 150mm thick (spread thickness) with Granite, Trap or basalt broken boulders or quarried stones, interstices filled, surface and rolled and consolidated to required gradient and camber as specified and direcetd

M&L for WBM 150mm thick (compacted thickness) in two layers of 75mm each with course aggregate of grading II (63 to 40mm) size, spread, leveled and rolled and consolidated to required gradient and camber using limestone, sand stone, flint or quartzite etc complete all as specified and directed

M&L for Preparing unsurfaced WBM surface by wire brushing for removing caked mud etc sweeping with brooms and finally fanning,cleanning using air compressor the cleaned surface with gunny bags to remove all loose dust etc on unsurfaced WBM

M&L for applying evenly a priming tack coat with bituminous primer @ 10Kg/10Sqm using paving bitumen VG 10 complete all as specified and directed

M&L for premix bituminious macadam(Design mix) (consolidated thicked 75mm or less with 4% binder content using paving bitumen of VG-30 grade by weight of total mix laid / rolled and compacted to required camber and gradient complete all as specifiied and directed. Note : (a) Premix bituminious macadam shall be obtained from hot mix plant and spreading shall be done with mechanical paver and asphaltic dense concrete work shall be done within 48 hours after completion of rolling and consolidation of bituminious macadam. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item. If there is any variation in the actual binder content used, the rate shall be adjusted @ Rs. 45/- per Kg of the binder used. However no price adjustment shall be made if the binder content workout to more as specified in shedule A.

M&L for 40mm (consolidated average thickness) Bituminous premix asphaltic semi dense with 5.5% binder(of paving bitumen VG-30) content by weight of total mix, rolled and compacted to required camber and gradient complete content by weight of total mix rolled and compacted using 8 to 10 tonne capacity power road roller to achieve the required compaction camber and gradient complete all as specified and directed. Note : (a) Premix concrete shall be mixed in hot mix plant,transported from plant to work site and laid / spread by means of mechanical paver. bituminious macadam shall be obtained from hot mix plant and spreading shall be done with mechanical pave. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item. If there is any variation in the actual binder content used, the rate shall be adjusted @ Rs. 45/- per Kg of the binder used. However no price adjustment shall be made if the binder content workout to more as specified in shedule A.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Supply and fixing cat eye/road studs made of polycarbonate moulded body with electronically welded micro prismatic lense on both side of colour -yellow/Red/Amber for maximum retro reflection in wet and dry conditions and to be fixed with BT-69 complete all as per manufacturer instructions and specified as directed of make :series 290 of 3M or equivalent.

M&L for preparation of road surface and applying thermoplastic reflective paint for marking of minium 2.5 mm thick single coat as a centre line or edge line etc road marking of 150/100 mm width using 'HOT MARK' thermo plastic paint (Hot application white/yellow by indenous modern propelled road marking machine as directed including all ingredients such as binder, glass beads, titanium dioxide, calcium carbonate, inter filler etc, thermoplastic requirement for glass beads shall be conforming to BS-6086 & MORTH specification including spraying of glass beads etc complete all as per manufactures instructions and as directed by Engineer incharge

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed

M & L for PCC 1:2:4 type B-1 (using 20mm graded stone aggt) as in as bonding and all other simillar works including necessary formwork etc complete all as specified and directed

Excavating post holes in soft/Loose soils (or similar holes ) n exc 0.50 Cum each and getting out and returning filling in balance portion (after PCC filling) with boulder and mixed with earth in layers exceeding 25 Cm thick complete all as specified and directed

S&F for mild steel Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc; half round or other stock section, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Supply and fixing for mild steel in flat,round or square bars in available legth complete all as specified and directed

S&F for GI barbed wire 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm barbs at 75 mm spacing and shall confirming to IS-278-2001 & IS-280-2006 and straining and fixing to any type of standrad rails straining bolts including securing or tying at crosssing with and provision of Galvanized mild steel wire, staples or steel pins etc as directed complete all as specified and directed

Supply only chain link fencing of mesh size of 75x75mm of 4mm dia mild steel galvanised wire including line wires, binding wire fixed to any type of standards, rails, straining bolts, etc complete all as specified & directed

Fixing only chain link fencing including line wires ,any mesh and any type of standrads rails, straining bolts etc including provisioning of binding wire complete as directed.

Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 5cm but n exc 10cm long 11 to 15mm dia of neck complete all as specified and directed.

S&F mild steel gate confirming to Fe-410-W gde E-250 Quality A as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing incl MS hinges, MS Sliding bolt, MS Handle and all other necessary mountings/fittings to keep gate functional complete all as specified and directed.

S&F 1 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M & L PCC 1:3:6 type C-2, 150mm thick for Concrete bed width (Outer diameter of drain pipes plus 400mm) for 200mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed

Supply and laying Reinforced concrete pipes, 200mm dia, class NP2, laid and jointed complete with collars etc complete all as specified and directed

S&F conventional LLDPE septic tank type-IV of capacity 3400 Litrs ,dia 1300 mm ,length 2600 mm and 16 mm thick of designed to carry sewage and sullage water,including excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 25 users complete all as specified and directed

M&L for Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed

M & L for brickwork with sub class ‘B’ bricks old size in one brick thick thick honey comb wall of soak well, built in cement mortar (1:4) complete all as specified and directed.

Demolition reinforced cement concrete in any description and in any position complete all as specified and directed.

M& L for dismantling Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor tile complete all as specified and directed

Dismantling water tanks exc 250 &n exc 500 litres complete all as specified and directed.

Dismantling water tanks exc 500 &n exc 1000 litres complete all as specified and directed..

Dismantling steel framed trusses n exc 10m span complete all as specified and directed

Taking up or down Steel Tubing bore of pipe in 15mm bore and including all connections, and removal to store etc complete all as specified and directed.

Taking up or down Steel Tubing bore of pipe in 20mm bore and including all connections, and removal to store etc complete all as specified and directed.

Taking down Bib tap of PTMT any colour ,any size complete all as specified and directed

Taking down Stainless steel sink, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc, any size complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm each not exc 4.00 sqm each complete all as specified and directed.

Demolition of brickwork masonary built in lime or cement mortar including all quiens arches, pillars etc. But including concrete articles complete all as specified and directed.

Dismantaling of asbestos cement (Corrugated, semi corrugated etc) sheetiting in roof covering all as specified and directed by Engineer-in-Charge.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling timber scantlings in framed work 40 sq. cm and over in section, in any position complete all as specified and directed.

Material and labour for concealed Point wiring for One light point/fan point /bell point controlled by one switch (using red, black and green etc colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core (FRLS) PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken terminal box (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLS PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. Note- Switch, socket, Regulatro & ceiling rose should be measeured & paid separately.

All as per item No.127 but for One Socket out-let 6 Amp point controlled by one switch (on independent board and not below the any other switch board) with 2.5 Sqmm (FRLS) copper conductor complete all as spedified and directed by Engineer-in-charge. (switches, socket etc. shall be measured and paid separately under appropriate items of BOQ/Sch A).

All as per item No 127 but for One Socket out-let 6 Amp point controlled by one switch (on same board) complete all as spedified and directed by Engineer-in-charge. (switches, socket etc. shall be measured and paid separately under appropriate items of BOQ/Sch A).

All as per item No 127 but for One Socket out-let 16 Amp power point controlled by one switch (on independent board and not below the any other switch board) with 4 Sqmm (FRLS) copper conductor complete all as spedified and directed by Engineer-in-charge. (switches, socket etc. shall be measured and paid separately under appropriate items of BOQ/Sch A).

S&F Switch Piano flush type single pole one way 6 Amp complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 6A complete all as specified and directed.

S&F Switch socket combination 2 in 1, 3 pin, 6 Amp, flush type complete all as specified and directed.

S&F Switch socket combination 3 pin, 16 Amp, flush type complete all as specified and directed.

Supply and fix electronic fan regulator 5 stepped type complete all as specified and directed

S&F LED decorative wall light fixture made up of Polycarbonate, suitable for 09W TU retrofit B-22 including LED bulb 09 Watt of colour temp 3000K & luminaire lumen >1000 lm complete all as specified and directed.

S&F ceiling rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for sub main wiring with two single core 6 Sqmm (FRLS) copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 Sqmm (FRLS) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. (Note:- Two runs of 6 sqmm (FRLS) and one run of 6 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Supply and fixing of VTPN DB suitable for Mounting MCCB as Incomer of rating 100 Amp Vertical distribution board 12 way with suitable rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

Supply and fixing of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with alum thimbles as required complete all as specified.

S&F of MCCB 100 Amp, 16KA, 4 Pole including complete electrical connection by appropriate size of alum lugs complete all as specified and directed

S&F of MCB SPN 63 Amp 240 volt 'C' curve 10 KA complete all as specifed and directed.

S&F of MCB SP 6 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and directed.

Supply and fixing LED lights fitting 4 Ft, 20 Watt, 220V, AC, batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F building security LED Light 30 Watt sensor based made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 25 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 25x6 mm for fixing of builiding security light fittings completed all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and driected.

Supply and fix exhaust fan, steel body AC single Phase 230V of size 300mm sweep with, blades, and frame and louvers including electrical connection complete all as specified and directed.

S&F of metal plug & socket DB with metal plug and MCBs single pole enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire of size 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, HT/LT equipments, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Excavation in trenches n. exc 1.5 m wide and exc 1.5 m but n.exc 3 m in depth and getting out soft loose soil for laying of under ground cable, foundation of pole and stay etc. complete all as specified and as directed

M&L for sand cushioning to U/G cable in layers of 25 cm thick(10 cm before laying the cable and 15 cm after laying the cable) and 18 cm for punned thickness( 8 Cm before laying the cable and 10 Cm thick after laying the cable) in trenches complete all as specified and directed. Note :- Only Puned down volume shall be measured.

Supply and lay burnt best quality locally available old size sub class 'B' bricks laid in trenches perpendicular to U/G cable for cable protection complete all as specified and as directed.

Material and labour for plain cement concrete using of ratio type D2 1:4:8 (40 mm graded stone) for foundation of poles and stay complete all as specified and directed.

Material and labour for plain cement concrete using of ratio type C2 1:3:6 (40 mm graded stone) for copying of poles and stay complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified and directed.

M&L cross arms, bracing, support clamps and back plates fabricated from structural steel sections including nut, bolts, washers, welding, bending cold or hot drilling holes for bolts in any shape or size as idicated for directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

Saupply and fixing 1.5 mtr 25 mm dia GI Pipe bracket suitable for fixing of street light pole/bldg complete all as specified and directed.

Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing LED building security street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66/67 protection complete all as specified and directed.

Supply and fixing of smart integrated all in one solar street light of 40 Watt, 5700 K with High efficiency Mono crystalline solar PV Module, Lithium Ferro Phosphate battery with in build BMS technology, High Efficiency LED, MPPT solar charge controller and Aluminium Extruded body & is specially programmed to automatically control the dimming and brightness of light, which increases the backup time including all necessary spares/connectors required for illumination of the solar light complete all as specified and directed.

M&L for Octagonal pole of 7 mtr height of bottom size 130 mm and top 70 mm dia with base plate size 220 x 220x12 mm, foundation bolts, Hot dip galvanized, single Arm suitable for fixing of All in one Solar Street light fitting of 24 Watt including necessary reducers, clamps, nuts, bolts and earth work, foundation with PCC 1:3:6/Foundation drg recommended by OEM as per drg, suitable for wind pressure of 100 Km/Hour as per OEM recommendation including dummy cap on the top of the pole complete all as specified and as directed. (Note : Foundation drg recommended by OEM be submitted by the contractor along with pole/clamp drg for approval of Accepting officer before placing order).

Supply and erect steel tubular swaged poles complete with cast iron base plate, finial taper plug,bolts, nuts & screws as specified type 410 SP-55 (11.0 metres long) conforming to IS-1678 and including marking alternate 05 Nos white and black strip 30cm height with two coats of synthetic enamel paint including preparation of surfaces, upto 1.5 metre above the coping of pole, starting with black strip, complete all as specified and directed. (Note: Excavation and earth wok and PCC for foundation, channel, clamps nuts, bolts to be measured and paid separately).

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing strip of size 25x4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, HT/LT equipments, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

Supply and fix electric water heater storage steel body with copper Inner tank and heating element upto 2 KW capacity 25 Liters, BEE 5 Star rated complete with all accessories such as safety vavle, thermostate, NRV and PVC hot & cold connections pieps, fashner set complete all as specified and directed.

M & L of Straight plain brass ferrules (or connecting screws) screwed both ends and fixed of size 20mm dia complete all as specified and directed.

M&L for Steel water tubing 25 mm bore with screwed & socket joints, medium grade, galvanized (including short lengths) with and including all necessary fittings, such as sockets, bends, elbows,unions, tees, diminishing pieces etc. fixed to walls or ceiling or laid in floors complete all as specified and directed.

Supply and fix Gun-metal, globe or gate valves, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply, installing, commissioning and testing Water Cooler fully stainless steel, electric driven single phase having approx storage capacity of 80 Ltr and nominal cooling capacity of 40 Ltr per hour with inlet PVC connection pipe of size 15 mm dia and 600 mm long of good quality complete with both ends CP nuts including electric connection through Voltage stablizer complete all as specified and as directed.

Supply & installing of Voltage stabilizer for automatic operation having input & output voltage, Amps, Over & low voltage cutout and timer delay function etc digital display single phase naturally air cooled indoor type & designed for input variation between 130 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA with wall mounting bracket complete all as specified and as directed.

S&F air termination multi point copper rod 12 mm dia and 300mm long fixed on PCC post 0.25x0.25m alongwith 1 mtr 20mm GI pipe med grade complete all as specified and directed.

S&F test point terminal block made of gun metal on phosphours bronze size 75x75x25mm drilling and screwed complete all as specified and directed

S&F copper strip 20x3 mm with saddles and fixing screws etc for down conductor to be fixed along the wall/ roof complete all as specified and directed.

M&L for Earthing complete with copper earth plate electrode 600x600X3.15 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below ground level earth plate connected with copper strip (20x3) mm as earthing lead by means of bolts, nuts, check nut and wahers of galavanised iron all as shown in Electrical plate No.3 of MES Sch part I and testing on completion. Including neccessary excavation and earth work, adequate common slat, charcoal dust and funnel PCC (1:3:6) type C-1 pit with pre-cast RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 8 mm dia bars, MS bar 3 Nos both ways funnel with 20, mm dia GI grade watering pipe earthing lead with GI protection pipe medium grade 40mm dia up to 7.5m. from earth plate to equipment earth point complete all as specified .

Taking down point wiring of any description and in any position complete all as specified and directed.

Taking down sub main wiring of any description and in any position complete all as specified and directed.

Taking down old U/S DBs including MCBs complete all as specified and directed.

Taking down old u/s tube light fitting bldg security light / bracket light / porch fitting of any description and in any position complete all as specified and directed.

Taking down metal clad including MCB any description and in any position

Taking down old earthing any description and in any position complete all as specified and directed.

M/S SEWA AND SERVE BUILDERS (BID ID -3319985)