PWD/BWN/Rs.6.86 lacs/ Special repair of Primary Health Centre at Village Bamla in Bhiwani Distt.

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR 8.5(B)

Scraping of Old White Wash/ Colour Wash (HSR 8.32a)

Scraping of Cement plaster HSR(8.32 (c )

Providing and laying 80mm thick interlocking paver blocks of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean.(HSR 13.14)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 in HSR(13.50)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified. (13.64)

Providing and fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (HSR 14.91) Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK.

Provding and fixing Ist quality ceramic glazed wall tiles confirming to I.S. 15622(thickness to be specified by the manufcturer) of approved make in all colours shades except burgundy,bottle green,black of any size as approved by Engineer-in-Charge in skirting risers of steps and dados over 23mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry,including pointing in white cement mxied with pigment to matching shades complete-300x450mm (14.92) (b)

15 mm thick cement Plaster 1:6 (HSR 15.12)

10mm thick cement plaster 1:4 under side of ceiling. (HSR 15.52).

Applying pink primer or aluminium priming ocat on wood work including preparation of surface, Knotting and stopping etc (16.2)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. HSR(16.5).

Applying priming coat with metal primer on new steel or iron work including preparation of surface. Painting on mettalic Surfaces etc. HSR(16.9).

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. HSR(16.60).

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla). (HSR 16.81)

Providing and fixing helical door spring 150 mm (superior quality), including necessary screws, complete- (b) iron HSR(17.79(b)

Supplying and fixing hydraulic door closer I.S.I mark, with necessary screws etc. complete (b) I.S.I designation no. II (size of door 701 mm to 850 mm) HSR(17.82(b)

Providing and fixing sliding bolt with nuts & screws etc complete. (b) Aluminium. HSR(17.83(b)

Providing and fixing 0.50 mm thick aluminium sheet, including cost of necessary screws, etc. complete. HSR(17.87).

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ,chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges,screws,chocks/cleats,stops,nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). (17.90(a)-30mm thick

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panelsof 12 mm thick, commercial veneered both side particle board or plywood of B.W.R. grade, hot pressed, including cost of iron hinges, screws, chock/cleats stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same position. (b) 35 mm thick. [HSR 17.91 (b) (-) 17.18 - Note]

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock & Champ only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. [HSR 17.92 (-) 17.18 - Note]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. HSR 17.93 (a) - Note 1 under 17.18] 25mm thick

S/F Glass panes including special metal sash putty of approved make. (b) glass panes 4 mm thic, exceeding 40 sq. dm areas. HSR(18.30(b)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)]. 1st quality q

Providing & laying 150mm thick (Compacted) stone metal (G-II) 53mm to 22.4mm gauge wearing coat to water bound macadam in two layer of 75mm each using screening type ‘B’ compacting with 3 wheeled steel roller/ vibratory roller to achieve the desire density including lighting, guarding barricading and maintenance of diversion etc. as per clause No.404 of MoRT&H specifications for road & bridge (5th Revision) of 2013 as per drawing and design directed by the Engineer-in-Charge complete in all respects. (N.S.). Note: Only crushed material should be used. No local earth/sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI).

PUBLIC HEALTH WORKS:- Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (b) Size 630 mm (ii) Single Colour. (Make Hindware) [HSR 30.2 (b) (ii)].

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLAT BLACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH consisting of:- (i) flat black lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval Of the Engineer-in-charge)(i) White. [HSR 30.19 (i)].

Providing & Fixing in position best Indian make (ordinary) lavatory suites consisting of:- (v) Size 560 mm x 450 mm with one no. tap. [HSR 30.41(v)].

Providing and fixing position best quality stainless steel sinks with complete fittings as fully described in item No. 30.51. (a) Size 600 mm x 450 mm x 200 mm. [HSR 30.53 (a)].

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making goods the walls etc. (a) C.P. Brass (i) Soap dish Large. [HSR 30.70 (a) (i)].

Providing & fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos. chromium plated brass screws and washers over rubbers washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian Make (i) 600 mm x 450 mm. [HSR 30.71 (a) (i)].

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75 (a) Bib cock long body.

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (ii)].

Providing and fixing in position best Indian make flexible tube connection. (b) C.P. Brass (iii) 15mm x 450 mm. [HSR 30.82 (b) (iii)].

Providing & fixing in position H.C.I. soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (a)100 mm internal diameter. [HSR 30.84]. ((a) 100 mm internal diameter.

(b) 75 mm internal diameter

Providing and fixing in position C.I. Gully trap cover weighing approximately 7.26 Kg. and frame for gully trap chamber clear opening size 300 mm x 300 mm and out side size 330 mm x 330 mm including painting the exposed surfaces with 3 coats of black bitumastic superior paint of approved manufacture etc. (HSR 30.85).

Providing lead caulked joints to H.C.I. pipes and specials confirming to I.S.I. specifications of E.L.C. manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc. (HSR 30.87). (a) 100 mm internal dia meter. (1.13 Kg)

(b) 75 mm internal dia meter. (0.91 Kg)

Providing & Fixing H.C.I. floor traps I.S.I. marked of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc. minimum depth of water should be 50 mm with a minimum seal of 50 mm. (b) with 75 mm i/d outlet. [HSR 30.89 (b)].

Providing and fixing in position H.C.I. specials for soil, waste, vent or anti-syphonage pipes to I.S.I. marked including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead jointing. [HSR 30.91 (a)]. For 100 mm dia ID pipe. (i) Heal rest bend.

(ii) Double junction with door 100 mm x 100 mm 100 mm x 100 mm

(xiii) Bend with door.

(xiv) Bend Plain

(xvi) Cowls.

(xvii) Door piece.

(xxii) Collars.

For 75 mm dia ID pipe (i) Heal rest bend.

(iii) Double junction with door 75 mm x 75 mm x 75 mm x 75 mm.

(xiii) Bend with door.

(xiv) Bend Plain

(xvi) Door Piece.

(xvii) Cowls.

(xviii) Collars.

Providing and fixing in position automatic brass ball valves in tanks. (b) With Plastic Ball (ii) 20 mm internal diameter. [HSR 30.110 (b) (ii)].

Providing & Fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150 mm x 150 mm cast iron cover weighing approximately 7.26 Kg. and frame clear opening 300 mm x 300 mm and outside size 330 mm x 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:2:4, in coping black bitumastic superior paint of approved manufacture on all C.I. work as per standard design, minimum depth of water should be 150 mm with a minimum seal 50 mm. (b) 100 internal diameter H.C.I. gull trap. [HSR 30.114 (b)].

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119].

Providing, fixing and jointing union couplings in G.I. and W.I. pipelines. [NS]. (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

(e) 40 mm internal diameter

Providing, Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside building including cartage from divisional stores or nearest railway station to site of works. (NS) (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. G.I. specials shall be of Make: - UNIK, TATA, ZOLOTO. (NS) 15 mm internal diameter of pipeline.

20 mm internal diameter of pipeline.

25 mm internal diameter of pipeline.

Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Brick 7183 Nos. @ Rs. 4/- Each

Brick bats 3.05 Cum @ Rs. 350/- P.Cum Note: All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

RATHIBUILDERS