REPAIRS TO FALSE CEILING FLOORING WALL PLASTERING ALUMINIUM DOORS WINDOWS ATT ETC IN DCI AND TECH AREA AT AF STATION AVADI

Amount

Demolition of cement concrete of any description (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), all as directed.

Material and labour for Plain cement concrete 1:2:4, type B1 using 20 mm graded stone aggregate, 100 mm thickness finished even and smooth without using extra cement as in hard standing etc., complete all as specified.

Material and labour for Plain cement concrete 1:4:8, type D2 using 40 mm graded stone aggregate as in sub base complete all as specified.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles of any descriptions, etc., complete all as specified and as directed.

M&L for Brick work with fly ash bricks straight or curved on plan exc 6mtr mean radius, built in CM 1:6 all as specified.

All as per item No 5.00 described here in before but except bricks (Note:- Serviceable bricks obtained from ser item No 4.00 will be used)

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. all as directed.

Material and labour for rendering 5mm thick in cement Mortar 1:4 mixed with Water proofing compound as per manufacturer's instruction over 10mm thick backing coat in CM 1:6 on fair faces of brick or on concrete surfaces finished even and fair, all as specified. Note : WPC shall be measured and paid separately

Material and labour for rendering 15mm thick in cement mortar 1:6 on fair faces of brick / concrete surfaces and finished even and fair all as specified.

Material and labour for rendering 10 mm thick on fair faces of ceiling of concrete surfaces in cement mortar 1:3 all as specified.

Material and labour for applying three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces and all as specified.

Material and labour for applying two coats of oil bound distemper over a coat of alkali resistant primer including preparation of newly plastered surfaces of walls, all as specified.

Material and labour for applying two coats of cement based paint over a coat of alkali resistant primer including preparation of newly plastered surfaces of walls all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, all as directed.

Dismantling of stone slabs/granite stone of any description or thickness in floors/dados laid bedded and pointed in cement mortar, all as directed.

Material and labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 etc., complete all as specified and as directed.

Material and labour for Glazed ceramic coloured /printed tiles in vertical surface 300x200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match Including by receiving the tile backing coat 10 mm thick in cement mortar (1:3) in vertical surfaces of walls/skirting etc., complete all as specified and as directed.

Material and labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed of 15 mm thick set in cement mortar 1:4 etc., complete all as specified and as directed.

Material and labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over screed bed or bedding layer of 15 mm thick in cement mortar 1:4 for laying floors, steps,jambs,pillars, window cills, cooking platforms etc , complete all as specified and as directed.

All as per item No. 19.00 described here-in-before but skirting/dados with 10mm thick in cement mortar 1:3.

Material and labour for Chequered cement concrete tiles 30cmx 30cm x 25mm thick of size as approved by GE set jointed and pointed in neat cement slurry in floors with white cement & pigment Including screed bed 15 mm thick cement mortar 1:4, all as specified and as directed.

Material and labour in repairs Machine pressed precast concrete interlocking paver block any shape & size conforming to IS 15658-2006 of 60mm thickness, with grey cement and pigment including sand cushion of 50 mm thick all as specified and as directed.

Material and labour for sand filling in polythene bag and laid over in layers at firing range all as directed

Supply only saw dust for firing range

Supply only Integral waterproofing compound

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, all as directed.

Dismantling of board with aluminium snap grid of (size 605x 605 mm ) complete, all as specified.

Material and labour for 12mm thick Perforated particle board/ tiles for insulation and accoustic purposes, 605x605 mm in size, fixed with screws on existing snap grid, in ceiling, flat or sloping, including two coats of synthetic enamel paint over a coat of pink primer exceeding 10 cm in width/girth all as specified and as directed.

All as per Item No. 28.00 above but for 12 mm thick semi perforated particle board of Make and pattern of M/S Armstrong to match with existing provision.

Fixing only ceiling board obtained from dismantling item No 26.00 of any description, all as directed.

Material and labour for anodised aluminium snap grid false ceiling of panels of size 605 x 605 mm using aluminium anodised wall angle of size 25 x 25 x 1.5mm thick fixed to walls with rawl plug and screws n. exc 1.50m c/c and intermediate panels using main "Tee" and cross "Tee" aluminium anodised section of size 35 x 25 x 1.50mm and 25 x 25 x 1.50mm thick suspended with GI wire of 4mm dia at 1.2 m interval including 12 mm thick semi perforated particle board fixed to frame work with screws and applying two coats of synthetic enamel paint over a coat of primer on exterior surfaces of ceiling board all as specified and as directed

Repairs to existing false ceiling without dismantling, by providing additional suspended wire of 4 mm dia and securing the wall angle by providing additional screws all as specified and directed

Taking down aluminium door of any size & refixing the same after repairing/replacement of damaged aluminium sections, all as directed. Note: Replaced Aluminium section aluminium mongries, glass etc., will be measured & paid separately as supply only

Taking down aluminium window of any size & refixing the same after repairing/replacement of damaged aluminium sections, all as directed. Note: Replaced Aluminium section, aluminium mongries prelaminated particle board and glass panes will be measured & paid separately as supply only.

Taking down aluminium ventilator of any size & refixing the same after repairing/replacement of damaged one, all as directed. Note: Replaced Aluminium section aluminium mongries, sheet glass etc., will be measured & paid separately.

Supply only Anodised aluminium frame for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc., complete all as specified.

Supply only 12mm thick prelaminated particle board exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed etc., complete all as specified.

Supply only 5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm each pane etc., complete all as specified.

Supply only Aluminium (Die cast) body door closer hydraulically regulated designation No 3, universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed, all as specified.

Supply and fix in repairs Aluminium (Die cast) body door closer hydraulically regulated designation No 3, universal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed, all as specified.

Supply only 150mm long floor door stopper Aluminium alloy body and tongue,anodised,with hard drawn steel spring fixed in floor, all as specified.

Supply and fix in repairs150mm long floor door stopper Aluminium alloy body and tongue,anodised,with hard drawn steel spring fixed in floor, all as specified.

Supply and fix in repairs Aluminium rebated Mortice Lock vertical type size 100mm four Lever complete all as specified.

Supply only Aluminium rebated Mortice Lock vertical type size 100mm four Lever complete all as specified.

Supply and fix in repairs 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, all as specified.

Supply only 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, all as specified.

Supply and fix in repairs 150 mm extruded aluminium alloy handles, fabricated type anodised, all as specified.

Supply only 150 mm extruded aluminium alloy handles, fabricated type anodised, all as specified.

Supply and fix aluminium , anodised , barrel tower bolts of extruded section and fixed 200 mm long, all as specified.

Supply and fix solar control film 50 microns reflective type sticked to glass panes as per manufacturers instructions.

S&F sheet glass 4mm thick glazing in square & rectangle not exceeding 0.5 sqm each pan with oil putty or aluminium beads fixed to steel etc all as specified.

Hacking out old broken glass (any size, quality or description) from metal frames,glazing with putting or beads.

Material and Labour for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

Material and Labour for treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

D Subramani and Sons

ANISHRAJAN ENTERPRISES

SWIFTTECH ENGINEERS INDIA PVT LIMITED