SPECIAL REPAIR TO BLDG NO 210 OFFRS ACCN 29C 292 QM STORE 49 GODOWN AND FEEDING THROUGH IN VARIOUS ANIMAL LINES AT EBS BABUGARH UNDER AGE BR II OF GE NORTH MEERUT CANTT

Amount

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in soft/ loose soil for foundation etc or for shaft, wells, manholes,pier holes etc n exc 10 Sqm on plan and not exc 1.5 m in depth and getting out and levelling of bottom surface to required level complete all as specified and directed.

Returning ,filling in including spreading ,levelling watering and well ramming of soft/loose soil in layers n exc 25 cm thick each complete all as specified and directed.

Removing excavated material ( spoil ) not exceeding 50 m distance and depositing where directed at a level n exc 1.5 metre above the starting point complete all as specified and directed.

M& L for providing Cement concrete 1:4:8 Type D 2 (using 40 mm graded crushed stone aggregates), in foundations, filling and mass concrete complete all as specified and directed.

M&L for 100mm thick cement concrete type B-2, 1:2:4 (40mm graded aggregate) for sub base of paver block complete all as specified and directed

M&L for providing Cement concrete 1:2:4 Type B-1 (using 20 mm graded crushed stone aggregates) in suface channels and drains including necessary form work, stops, moulds etc complete all as specified and directed.

M&L for providing Cement concrete 1:3:6 Type C 2 (using 40 mm graded crushed stone aggregates) in suface channels and drains including necessary form work, stops, moulds etc complete all as specified and directed.

M&L for providing cement concrete 1:3:6 Type C-1 (using 20 mm graded crushed stone aggregates) in cills, copings, kneelers, bed plates, kerbs hold fast, fillings in pressed steel door frame and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for providing reinforced cement concrete 1:2:4 (nominal mix) type B 1 (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for providing reinforced cement concrete 1:2:4 (nominal mix) type B 1 (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

All as per Srl item No 11 here-in-before but except bricks

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:4 complete all as specified and directed.

All as per Srl item No 13 here-in-before but except bricks

M&L for Brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for providing formwork rough finished surfaces to edges of concrete flats, brick in floor cills, railing etc & similar works exc 10 cm but n.exc 20cm wide complete all as specified and directed.

M&L for providing formwork to sides of square ,rectangular or polygonal pillars, posts, struts, piers, and columns rough finished surfaces of concrete flat complete all as specified and directed.

S&F factory made glazed, gauzed and skeleton shutters 35 mm thick 2nd class hardwood (SAL/ CHAMP / HOLLOCK) open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); for doors and fitted to chowkats complete all as specified and directed.

M&L for 16-18 mm thick machine cut mirror polished Granite stone slab of any colour table rubbed polished and round edges as in cooking plateform, steps and window cills and like over and including 10mm thick scread bed in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade / colour / matrix of granite complete all as specified and directed.

S&F plain framed, panelled shutter (two panel) factory made 35 mm thick of 2nd class HW with rail stile and lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part-I), Kiln seasoned and chemically pressure treated, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) not exc. 1.5 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & all as per SSR Part-II complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & all as per SSR Part-II complete all as specified and directed.

Supplied and fixed anodised aluminium window and ventilator with side hung shutters without sash bars aluminium section weighing 0.55 kg/RM with and including, necessary jointing cleat, glazing,clip, rubber packing,,anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 no) suitable handle (1 no) complete all as specified and directed. Note : Glazing / sheet glass shall be measured & paid separately.

Supplied and fixed steel windows with pressed steel frame made out from 1.25 mm thick steel with one or more rebate with glazed shutters and fly proofing shutters including guard bars, hinges, peg stay , handles tower bolts lugs including treated with tar or coal tar black paint on steel surfaces in contact / embedded in concrete / masonry work complete all as specified and shown on drawings (Note : Disturbed surface of wall shall be made good to true surface)

S&F 100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt having shoot / dia of bolt not less than 10mm complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt having shoot / dia of bolt not less than 10mm complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, having shoot / dia of bolt not less than 12mm complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 250 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 300 mm long aluminium anodised, sliding door bolts, with haps staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts not less than 16mm dia of shoot / bolt of sxtruded section or cast aluminium alloy complete all as specified and directed.

Supply only Integral water proofing compound (I.S.I marked on packing)complete all as specified and directed.

S&F Butt hinges of 100 mm size, Medium weight, cold rolled mild steel and fixed, complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised,width of flap (when open ) 40 mm. complete all as specified and directed.

S&F 150mm size Mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed.

S&F 40mm dia,brass polished, bright finished cupboard knobs fixed with nut, screw and washer complete all as specified and directed.

S&F in repairs MS chromium plated tubular curtain rod 19mm dia, complete all as specified and directed.

S&F in repairs brass chromium plated brackets for curtain rod 20 mm dia.complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including necessary beadings complete all as specified and directed.

S&F mild steel work as for Hand rails, half round or other stock section , nosing to steps in cluding embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) . including necessary riveting and / or welding and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F mild steel work as for framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work including necessary riveting and / or welding conforming to Fe 290 (Gde-E 165) complete all as specified and directed.

Supplied and fixed mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 5-10 mm dia of neck and n exc 5cm long, complete all as specified and directed.

S&F mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised 12 mm dia of neck and exc 30cm long complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. Note :- Weight of binding wire shall not be considered for measurement and payment purpose.

M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. Note :- Weight of binding wire shall not be considered for measurement and payment purpose.

S&F rolled mild steel in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.

S&F rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.

S&F rolled mild steel in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.

S&F welded steel wire fabric cut to length bent to shape required and tying including necessary welding and fixed to steel members weight n.exc 4 Kg per Sqm complete all specified and directed

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F factory made steel windows with side hung shutter including projection type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F anodised aluminium snap grid frame work for size of grid 605x605 mmfor false ceiling complete all as specified and directed.

S&F valley gutter made out of 1.25mm thick PGI sheet, with grade of zinc coating 275 gm/ sqm (both sides) including GI through both sides of valley gutter and bottom provided with 150mm outlet projected up to 200 mm suitable to be couplied with GI rain water pipe and drilled for proper connection with trough, joints shall be welded by gas welded complete all as specified and directed .

M&L for 15 mm thick screed bed in cement mortar 1:4 as in roof mixing with WPC mixing with water proofing compound by 3% by weight of cement or as per manufacturers instructions complete all as specified and directed Note :- Water proofing compound will be measured and paid seperately.

M&L for bitumastic gola, with 80/25 bitumenand coarse sand mixture 1:3 by weight 8cm x 8cm at the junction of roofing to vertical surfaces specified and directed

M&L for preparing, cleaning new concrete/plastered surface and applying evenly a tack coat @1.20 kg/Sqm with 85/25 industrial bitumen over a coat of bitumen primer @ 0.30 liter/Sqm and laid with 3mm thick APP modified polymeric water proofing membrance with non-woven polyester rainforced and applying a tack coat of 85/25 industrial bitumen @ 1.2 kg per Sqm and finish the surface with aluminium paint at top @ 0.2 kg/Sqm as per manufacturer's instructions. Weight of membrane shall not be less than 3.6 kg/Sqm unrolled and bonded to substrate with side and end laps 75mm & 100mm as per manufacturer's instructions. complete all as specified and directed. Note :- The WPT work shall be got done through manufacturer's authorised applicator only under strict supervision of manufacturer's technical representative.

Supplied and fixed pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with hot dip galvanised self dirilling and self tapping screws neoprene and EPDM washers complete all as specified, directed and as per manufacturer's instructions

Supplied and fixed pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with hot dip galvanised self dirilling and self tapping screws neoprene and EPDM washers complete all as specified, directed and as per manufacturer's instructions

M&L for 19 mm thick particle board, medium density, flat pre-ssed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame as in shelves cup board cabinets, in palmet boxed or similar items open edge of board fixed with Ist class HW wooden beading fitted with nuts & bolts comlete in repairs complete all as specified and directed.

Supplied and fixed fibre cement coloured textured designer ceiling board 4mm thick of size 595x595 mm conforming to IS : 14862 & IS : 2380 Part-XIV fixed to timber / GI / Aluminium frame work with screws/clips complete all as per manufactures instructions and as directed. Make : Everest, Charminar, UPAL.

M&L for 18-20 mm thick machine cut Kota stone slabs of size 540 mm x 540 to 560mmx 560mm in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the stone slabs, including necessary grinding rubbing rounding to exposed edges and polising in granite finish complete all as specified and directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry over CM screed (screed shall be measured and paid for separately under respective item), jointed and grouted with tile epoxy grout complete all as specified and directed".

--------------BLANK------------

M&L for Glazed ceramic tiles coloured 300mmx 450mm X 7 mm thick first quality of grade B tiles on vertical surface such as skirting / dados etc set in neat cement slurry over CM screed (screed shall be measured and paid for separately under respective item). Jointed and grouted with tile epoxy grout complete all as specified and and directed

M&L for table rubbed & mirror polishing and pointing in white cement 1:2 using marble dust with admixture of pigment to match with existing shade to marble work complete all as specified and directed

Supplied and fixed in repairs CP soap dish make-Jaquar cat part No-1131 complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in floor/plinth protection , finish even & smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) laid in alternate panels as in plinth protection , finish even & smooth without using extra cement complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.

Roughening surface of old concrete floor surface by picking , sweeping cleaning and washing down with water to remove dust etc from the site complete all as specified and directed.

M&L in repair for laying 80 mm thick machine pressed precast PCC coloured interlocking paver block moulded in PVC frame / mould any shape and size conforming to IS 15658-2006 of M-40 grade of approved design with gray cement and pigment to match shade / colour / matrix of tiles set and bedded over and including 50mm thick fine river washed sand duly compacted with surface vibrator laid over compacted sub soil in flooring complete all as specified and directed. Make : NITCO, Mumbai ; Redsun tiles & Pavers, panchkula ; Star Tiles & Industries, Rama Devi, Kanpur ; Mayur tiles & Interlocking Pavers, Lucknow ; Mehatab tiles, indore ; Tulip Infrastructure, Saharanpur (U.P)

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 10mm thick in CM 1:4 for laying tiles in vertical surfaces complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

M&L for rendering 15mm thick cement plaster with cement mortar (1:4) on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement with using water proofing compount Note :- Water proofing compound will be measured and paid seperately.

M&L for preparing the new plastered surfaces and applying three coats of white lime washing on walls complete all as specified and direcrted.

M&L for preparing the new plastered surfaces and applying two coats of oil bound distemper over a coat of primer on walls completeall as specified and direcrted.

M&L preparation of old decorated surfaces of walls and applying two coats of oil bound distemper complete including removal of existing treatment. complete all as specified and directed .

M&L for preparing the newly plastered surfaces and applying two coats of cement base paint over a coat of primer on walls / vertical surfaces complete all as specified and direcrted.

Taking down old existing water proofing treatment from top of RCC/arch slab including taking down of concrete padding or plaster and raking out joints of arch slab and hacking the top of RCC slab, cleaning with water and dispose off rubbish upto 200 meter complete all as specified and directed

M&L for preparing of old decorated surfaces of walls (plastered or un plastered) including cornices etc and applying one coat of cement base paint including repair with wall care putty wherever required complete all as specified and directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coat of white / tinted synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of white / tinted synthetic enamel paint complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10 cm in width or girth and applying one coat of white / tinted synthetic enamel paint complete all as specified and directed

M&L for 3 mm thick sheet glass, ordinary quality and glazing with oil putty or glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L for 4.8mm thick sheet glass, fixed on aluminium door / frame / windows in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M&L for 4.8mm thick sheet glass fixed on aluminium door / frame / windows in square exc 0.50 Sqm in each pane complete all as specified and directed.

Taking up or down GI water tubing 15mm bore and unserviceable removal from the site complete all as secified and directed

Taking up or down GI water tubing 20mm bore and unserviceable removal from the site complete all as secified and directed

Supplied and fixed GI water tubing 15 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Supplied and fixed GI water tubing 20 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Dismantling of old water tank exc 250 Ltr & n.exc 500 Ltr capacity and Supplied, hoisted and fixed inposition rotational moulded polyethylence water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball valve high pressure of PTMT with apoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

S&F in repairs bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia and fixed complete all as specified and directed.

S&F in repairs stop valves, 15mm bore dia, CP cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supply and fixed in repairs gun metal globe or gate valves, 20mm bore dia, with iron wheel head ,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supplied and fixed in repairs CP towel ring 150mm size square type complete all as specified and directed.

Supplied and fixed in repairs CP toilet paper holder dia complete all as specified and directed.

S&F in repairs PVC co0nnections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supplied and fixed in repair vitreous china WHB white flat back size 550x400mm including Supplied and fixed angle iron brackets, C.P pillar tap fency type 01 No 15mm bore, CP waste coupling, 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.

S&F in repairs wash basin fancy type with full pedestal, 32mm dia brass CP waste coupling & PVC waste pipe complete all as specified and directed. Make : CERA Cat Part No S2040114 (WHB) & S2090108 (Full padestal) or equivalent in Jaquar

Supply and fixing in repairs vitreous china squatting pan, Orissa' pattern, size 580 x 440mm white, with integral foot rests with and including cast iron 'P' or 'S' trap and setting the trap and pan in and including PCC 1:4:8, type D-2 minimum 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, making all connections complete all as specified and directed.

Supply and fixing in repairs vitreous china urinal bowl, flat back of size 465x355x265mm (minimum) white with grating and unionfor discharge pipe (excluding flushing cistern,flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusiveof fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed.

Supply and fixing in repairs PVC low level flushing cistern of 10 Ltr capacity syphonic action type with inlet ball valve, float and handle including PVC brackets for mounting of cistern complete all as specified and directed.

Supplied and fixed in repairs 125 mm size brass chormium plated shower rose including fixing to steel pipe or union complete all as specified and directed

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs plate rack of stainless steel , 1mm thick for kitchen or labotary, overall size 720x600x230 mm ,fixed with plugs and washers on wall complete all as specified and directed.

--------------BLANK------------

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of RCC in floors(other than ground floors beams, chajjas, lending slab and similar suspended works and including reinforcement cut on required to facilitate demolition and removing of debris & rubbish from the site complete all as specified and directed.

Dismantling of timber scantling framed work 40sqcm and over in section in any position complete complete all as specified and directed.

Dismantling of timber scantling framed work under40sqcm in section in fillets, rails posts etc complete all as specified and directed.

Dismantling AC sheet corrugated or semi corrugated sheet of any description as in roof and including removal from the site complete all as specified and directed.

Dismantling of wall or ceiling board (fiber,pulp,insulation etc) any thickness including cover fillets and removal from the site complete all as specified and directed.

S&F in repair vitreous china EWC complete with inbuilt vitreous China cistern, with soft close seat cover and with twin flush fittings, brass CP hand faucet with all necessary fittings complete all as specified and directed. Make : CERA Cat Part No S1013159 or equivalent in Jaquar / Hindware

S&F in repairs fancy type brass CP hot and cold wash hand basin mixer 15mm bore screwed down high pressure with long screwed shanks and fly nuts, screwed to iron piep complete all as specified and directed

M&L for providing precast cement concrete 1:1.5:3 type A-1 (using 20 mm graded crushed stone aggregates) as in kerb stone and set in cement mortar 1:6 complete all as specified and directed.

S&F in repair chromium plated glass shelf of size 22" complete all as specified and directed. Make - Jaquar, Parko, Gem or equivalent

mohanlal gupta

Rajneesh Jain

GARG CONSTRUCTION CO