CONSTRUCTION OF RECORD ROOM (Call 2)

Amount

Main Control Panel : Fabrication, supplying and installation of outdoor type cubical panel board of suitable size made out of GI sheet 2 mm thick (14 SWG) and powder coated thereafter, duly compartmentalised having door locking arrangement for protection from rain, dust, duly fixed on GI angle iron frame work and having following accessories mounted inside the panel including connection, inter connection with aluminium thimbles, earthing with two nos. earth studs, duly powder coated complete etc. as required,Civil Foundation cost for the panel shall be inclusive. Cable gland plates shall be provided on bottom. 2 Nos. earthing terminals shall be provided. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Incomer :250A TPN MCB - 1NOS Outgoing : 25A TPN MCB - 6 NOS & 32A DP MCB's - 1nos; 63A TPN MCB - 2nos Indication lamps (RYB) Danger notice plate Make : As listed in UHBVNL

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 16sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 3.5C x 50sqmm Al Ar cable

SITC of 20W LED Batten having Extruded aluminium housing fitted with Engg. Plastic end caps. With Opal diffuser.LED should be populated on FR4 PCB in which LED’s should be mounted & connection should be in series parallel.LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level)>=110lumens/watt, Minimum system Lumens 4400 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 6500K ±500K, CRI>=80, PF>=0.9,THD<10%, and Operating Temperature Range-10 deg C to +50deg C, IP20. Built in Surge Protection of 4KV and an operating Voltage Range of 140 to 300V AC,50Hz.The driver should be constant current driver.The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. Bajaj Cat. Ref.BCLAB SP 20L LED CW PC SD or Equivalent.

Supply of LED recessed Downlighter with a nominal system lumen output of 1200 lumens ±10% and a minimum system efficacy of 100 lm/W. The luminaire should have a color temperature of 5700K and CRI>80. The luminaire shall meet IP20 rating with THD<10% and PF > 0.95. Built-in Surge protection of 2 kV,Maintenance of lumen output 50000 hrs.The luminaire housing should made of pressure die cast aluminium with a high efficiency diffuser.Bajaj Cat. Ref BZSLOS nxt 12L LED WH SD

SITC of recessed mounted LED 600x600mm fitting made of CRCA) sheet steel housing comprising of LED’s connected in series parallel,Opal diffuser fixed in separate white powder coated ,Opal diffuser frame is held in with housing by screws for easy maintenance. Fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, ,Minimum system Lumens 3600 lm ±10%Life of fixture 50000hrs@L70 Lumen maintenance, CCT up to 5700K±300K, CRI minimum 80, PF ≥0.95, THD <10% and an operating Voltage Range of 140 to 277V AC. Minimum Internal Surge Protection 2.5 kV. The fixture should comply with the other parameters as per IS10322 and specifications. Bajaj Cat. Ref BZRSLL 36W LED WH i

Supply of 40W LED industrial Weatherproof Batten having Extruded aluminium housing fitted with end caps. Luminaire should be Completely prewired with accessories up to terminal block and fixture should have minimum efficacy at System level (Not Chip Level)>=120lumens/watt, Minimum system Lumens 4800 lm ±10%. Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 6500K ±500K, CRI>=80, PF>=0.9,THD<10%, and Operating Temperature Range-10 deg C to +50deg C, IP65,IK07. Built in Surge Protection of 4KV and an operating Voltage Range of 140 to 300V AC,50Hz.The driver should be constant current driver. The fixture should comply with the parameters as per IS10322 and IEC60598, EMC / EMI compliance. Bajaj Cat. Ref.BI PC 40W XE TYPE or Equivalent.

SITC of 300mm swepp Light duty exhaust fan with metal blades etc complete

SITC of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 W, BEE 5 star rated, ceiling fan with Brush Less Direct Current(BLDC)motor, class of insulation: B, 3 no's blades, 30 cm long down rod, 2 no's canopies, suitable for 230V, 50 HZ, single phase AC supply, earthing etc., including all standard accessories etc., complete.

10KVA UPS for Emergency lighting and UPS sockets

Providing & Installing of Gearless Passenger Elevator,Capacity 884 Kg / 13 person,speed 1.00 meter /sec,control high performance simplex full collective control system Drive: Ac VVVF Drive for more power saving,comfort & safe ride.Stops/opening :03 Stops/03 Opening,travel 18 meters approx,Gearless Machine Shall Be Placed within the shaft(MRL),S.S Hairline Finish Cabin, PVC Flooring on heavy duty M.S. Platform, Decorative False Ceiling WithCFL/LED Lighting, Blower/Rotor motor Fan.Clear Opening 800mm wide x 2000mm Height,Car door Center Opening Automatic Door ( SS Hairline Finish) Power Supply Three Ø 415 V AC, 50 Hz +/- 5% Single Ø 230 V AC, 50 Hz +/- 5%,These Components are generally confirmed as per Indian Standard Specification for Elevators orEscalators,SPECIAL FEATURES 1. Direction arrow with digital position indicators in car and at all landing ,2. Very attractive push buttons with illuminated call registration light in car and all landings ,3. Car emergency light, emergency alarm and emergency stop operation,4. Intercom communication system from car to ground floor & machine room.,5. Voice announcing system for car,6. Full length infrared door curtain safety for auto doors,7. Automatic rescue device in case of power failure or emergency landing (ARD),8. Fireman switch safety device as per elevator & escalator act.,9. Overload warning device (OLWD). All complete fitting as directed by engineer in charge.Make required Orbis,Jhonson,Kone,otis

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase, 50HzAC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

INDOOR UNIT-CASSETTE TYPE Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeedmotor, coilsection with DX Coppercoil , electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote controletc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree CDB and 19Degree CWB temperature. 2 TR

INDOOR UNIT-HIGH WALL TYPE Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V±10%, 50Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree C DB and 19 Degree C WB temperature. 1TR

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V±10%, 50Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree C DB and 19 Degree C WB temperature. 1.65TR

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 15.86mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 19mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 25.4mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

Netwrok Video Recorder (NVR) 32 CHANNEL NVR 4 SATA WITH HDMI AND VGA PORTS IP VIDEO INPUT 32-CH UP TO 12 MP RESOLUTION TWO-WAY AUDIO 1-CH, RCA (2.0 VP-P, 1 K Ω) Network Incoming bandwidth - 320Mbps Outgoing bandwidth-256 Mbps Recording resolution:12 MP/8 MP/6 MP/5 MP/4 MP /3MP /1080p /UXGA/720p/VGA /4CIF/DCIF/2CIF/CIF/QCIF Video & audio output: HDMI1/VGA1 output resolution : HDMI1: 4K (3840 × 2160)/60Hz, 4K (3840 × 2160)/30Hz, 2K (2560 × 1440)/60Hz, 1920 × 1080p/60Hz, 1600 × 1200/60Hz, 1280 × 1024/60Hz, 1280 × 720/60Hz, 1024 × 768/60Hz HDMI2 output resolution : 1920 × 1080p/60Hz, 1280 × 1024/60Hz, 1280 × 720/60Hz, 1024 × 768/60Hz Decoding format: H.265+/H.265/H.264+/H.264/MPEG4 Live view/ Playback: 12 MP/8 MP/6 MP/5 MP/4 MP/3 MP /1080p /UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF Network protocols: TCP/IP, DHCP, Hik- Connect, DNS, DDNS, NTP, SADP, SNMP, SMTP, NFS, iSCSI, UPnP™, HTTPS Hard disk capacity SATA: 4 sata 4 hdd Up to 8 TB capacity for each HDD Network interface:1 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interface Working temperature:-10 °C to 55 °C (14 °F to 131 °F) Power supply: 100 to 240 VAC 1 no. (SP 10/16A MCB) Model: HIKVISION DS-7732NI-I4 OR Equivalent

2MP NETWORK BULLET CCTV 1/2.8" progressive scan CMOS Up to 2.0 megapixel 2.8 mm/4 mm/6 mm fixed focal lens Up to 30 m IR range Dual stream Digital WDR (Wide Dynamic Range) 3D DNR (Digital Noise Reduction) PoE (Power over Ethernet) IP67 Mobile monitoring via Hik-Connect or iVMS-4500 Day &Night IR cut filter with auto switch Max. Resolution: 1920 × 1080 Protocols: TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, NTP, UPnP, SMTP, IGMP Operating Conditions: -30 °C to 60 °C (-22 °F to 140 °F), humidity: 95% or less (noncondensing) IR Range: Up to 30 m MAKE: HIKVISION / CP Plus

2 MP Full HD WDR IR Vandal Dome Camera - 30Mtr. Feature Specification Image Sensor 1/2.8” 2MP Progressive scan CMOS Effective Pixels 1920(H) x 1080(V) Minimum Illumination 0.006Lux/F1.4 0.005Lux/F1.2( Color,1/3s,30IRE) 0.05Lux/F1.4 0.04Lux/F1.2 (Color,1/30s,30IRE) 0Lux/F1.4(IR on, B/W) Shutter Speed Auto/Manual, 1/3~1/100000s White Balance Auto/Natural/Street Lamp/Outdoor/Manual Lens 2.7mm~13.5mm motorized Lens Gain Control (AGC) Auto/Manual Angle of View H:106°~29°, V:57°~17° Video Compression H.265+/H.265/H.264+/H.264H/MJPEG (Sub Stream) Back Light Compensation BLC / HLC / WDR(120dB) S/N Ratio More than 50dB Video Streaming 1080P (1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps) Resolution 1080P(1920x1080)/SXGA(1280×1024)/1.3M(1280× 960)/720P(1280×720)/D1 (704×576/704×480)/ VGA(640×480)CIF(352×288/352×240) Digital Zoom 16x Motion detection Off / On (4 Zone, Rectangle) Privacy Mask Off / On (4 Area, Rectangle) ICR Auto (ICR)/Color/B/W ROI Off / On (4 Zone) Audio Input 1Ch. Audio Output 1Ch. Audio Compression G.711A;G.711Mu;G.726;AAC Alarm IN 1 channel In: 5mA 5VDC Alarm Out 1 channel Out: 300mA 12VDC Bit Rate H.265: 12K ~ 6400Kbps , H.264: 32K ~ 10240Kbps Protocol HTTP; HTTPs; TCP; ARP; RTSP; RTP; RTCP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPoE; IPv4/v6; QoS; UPnP; NTP; Bonjour; IEEE 802.1x; Multicast; ICMP; IGMP; ONVIF Profile S&G, API ,TLS Smart Detection Tripwire, Intrusion Event Trigger Motion detection, Video tampering, Scene changing, Network disconnection, IP address conflict, Illegal access, Storage anomaly Ethernet RJ-45 (10/100Base-T) User Account 20 Users Smart Phone iPhone, iPad, Android Phone IR IR Range of 30 Mtr. ,Smart IR Micro SD Micro SD Card128GB Operating Temperature -30°C~+60°C , Less than 95%RH Power Source DC12V, PoE (802.3af) MAKE: HIKVISION / CP Plus Power Consumption <9W Casing Metal Weatherproof Standard IP67 & IK10 Dimension φ122mm x 88.9mm Weight 0.4Kg

POE SWITECH : POWER ON ETHERNET Netgear GS110TP ProSafe 8-PortGigabit PoESmartwith 190W Power-over-Ethernet budget and 2 SFP ports for wireless converged networks, IP surveillance and mobility,2 dedicated Gigabit SFP fiber ports. Make : NETGEAR / Dlink / TP link

24 PORT PATCH PANEL : NETWORK MANAGER Preferred Make : D'LINK/ NETGEAR/TPLINK

RACK 2U : TO MOUNT POE SWITCH HARDWARE CABLE MANAGER + FAN + 4 PORT POWER STRIP

LED monitor - 44 inch (Make : LG/SAMSUNG/SONY)

DATA TRANSMITION CAT-6 Cable Armoured with 25mm dia PVC conduits pipe with all required accessories (bends, flexble conduits, Junction box etc)

Providing 6Kg Fire Extinguisher Mono Ammonium Phoshate Powder 50, Stored Pressure Type, Pressure Gauge, Gross weight 9.5 Kg, empty weight 3.5 Kg, Can Height 435MM, Diameter 160MM, Discharge Time less than 9 Sees, Controllable discharge mechanism, Range minimum 4 meters, applicable on Class A,B,C and electrically started Fire, A Rating 21A, B Rating 898, Can construction: Deep drawn & Co., Mig welded, valve construction : Forging and Machining, Internal Coating of Can ; Epoxy powder coating, External Coating of Can : Epoxy Polyster power coating, sheet metal thickness: 1.60MM, Helium Leak Detection Tested, lSI and EN Approved, 5 years

WARRANTY 4.5 Kg C02 Gas Type Fire Extinguisher, Trolley Mounted, Easy Weight Providing Management used Unused Mechanism, Squeeze Grip, Gross weight 19.1 Kg, empty Weight 14.6 Kg, Can Height 857MM Diameter 140MM, Discharge Time Less than 10 Sees, Controllable discharge· ('mechanism, Applicable on Class B&C Fire, B Rating 218, Can Constrution :Hot spinning/Forging, Value Construction: Forging & Machining, Internal Coating of Can : Not Apllicable, External Coating of Can : Spray Painting, Sheet metal thickness : 4.5 MM lSI Approved, 1 Year Warranty.

Providing 9 Ltr Fire Extinguisher, AFFF Foam Type, Stored Pressure Type, Pressure Gouge, Gross Wreight 14.6 Kg, empty Weight 5.6Kg, Can Height 611 MM Diameter 175 MM, Discharge Time Less than 60 Sees, Controllable discharge mechanism, Range minimum 6 Meters, Applicable on Class A,8&C A Rating 13A, 8 Rating 558, Can Constrution . Deep drawn & Co, Mig welded, Valve construction; Forging & Machining, Internal Coating of Can : Epoxy Powder coatingm, External Coating of Can : Epoxy Polyster Powder coating, sheet metal thickness, 2.0 MM, lSI and EN Approved, Helium Leak Detection Tested, 1 Year Warranty.

Capacity : 9 Litres Fire Buckets and Stand : Supplying of four bucket stand along with buckets.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supply Installation, Testing & Commissioning of wall mounting loop powered addressable type hooter with all accessories.

Providing and commissioning REVOLVING CHAIR With ARM central tilt,Pedestal Base:Glass Fibre Nylon with ABS/ NylonTwin Caster Wheels Minimum 5 Nos, of 50 mm Size,Arm Material:steel covered with polyurethane,seat material:pressed and moulded plywood with polypropylene cover,Material of Fabric Back Cover / Material for Backrest:mesh fabric,Material of Fabric of Seat Cover:foam laminated mesh fabrics,Chair Type:central tilt,Height Adjustment ± 5(mm):up to 100 mm,Type of backrest support:backrest with lumber support of polypropylene at multilevel across back,Arm Type:Adjustable,Ergonomic Seat Design:yes,Back type:fixed,backrest has separate adjustable headrest:no,Number of arm movement:2(up & down),Lumber support:integrated,Overall Chair Height ±15mm:710,Backrest Height ±15mm:460 millimeter,Backrest Width ±10mm:410 millimeter,Seat Height ±15 mm:420,Seat Width ±10 mm:440,Seat Depth ±10 mm:400 millimeter,Thickness of MS Plate Joining the under structure with Seat:0.2 millimeter,Thickness of Plywood used in Seat ±1(mm) :12 mm,Thickness of Plywood used in Backrest ± 1(mm):12 mm,Thickness of Polyurethane Foam Used in Seat in mm (+/- 2 mm) :25 mm,Thickness of Polyurethane Foam Used in Backrest IN MM (+/- 2 MM) 25 mm,Warrantee period in number of years:5-year

Providing and commissioning GODREJ INTERIO Executive Table of MDF board of grade SBG II of IS 12406/Latest 1650 millimeter 750 millimeter 750 millimeter ,Storage provided One side,Keyboard tray:Not provided Foot rest:Not Provided,Table top Material:MDF board of grade SBG II of IS 12406/Latest,Gable end and modesty panel material:Flat single layer prelaminated MDF board conforming to having designation PLMDF-23 of IS 14587/Latest,Leg Material NO LEGS,Thickness of table top ±2 mm:25 millimeter,Length of table top ±10 mm:1650 millimeter ,Depth of table ±10 mm:750 millimeter,Height of table ±10 mm:750 millimeter, Dimension of leg(mmXmm) ±5mm:No legs, Number of Storage unit provided:Double storage, Material thickness of footrest ±2mm:N.A, Warrantee period in number of years:1, Product having BIFMA certification:NO, OEM of offered product is ISO 9001:2015 certified:YES, OEM of offered product is ISO 14001:2015 certified:YES, OEM of offered product is ISO 18001:2007 certified:YES

Providing and commissioning GODREJ INTERIO REVOLVING CHAIR With ARM central tilt Pedestal Base Glass Fibre Nylon with ABS/ NylonTwin Caster Wheels Minimum 5 Nos, of 50 mm Size Material: Arm Material:Proypylene,seat material:PU Foam covered with Fabric,Density of PU foam used in seat KG per Cu Meter (+/- 3):45,Density of PU foam used in backrest in KG per Cu Meter (+/- 3):NA,Material of Fabric Back Cover / Material for Backrest Innner frame Upholstered with Mesh fabric and mounted on main assembly,Material of Fabric of Seat Cover:100% polyester fabric,GSM/Thickness of fabric ±5%(Gram/Square meter):250 gram, Genral : Chair Type:central tilt,Tilt Tension Adjustment:Yes,Height Adjustment ± 5(mm):up to 100 mm,Arm:With,Type of backrest support:Countered lumber supporting, Arm Type:Fixed ,Colour of Fabric for Seat and Backrest:black,Ergonomic Seat Design:Yes, Back type:push back,Backrest is made of two pcs injection moulded frame:Backrest is made of one piece injection moulded frame backrest has separate adjustable headrest:No,Seat type:fixed,Seat is curved:Yes,Locking mechanism:Yes,Type of locking:upright locking Number of arm movement N.A,Lumber support N.A

Installation and commissioning of the entire Modular work station, Modular work station Other wood Hybrid panel based system (combination of sliding & snap fit tiles) Modular Work .Type / Shape of cluster: Stations Single Seater L Shape Cluster,Construction of drawer unit:Wooden front with PVC lipping,Construction of pedestal:free standing low height with castor,Work top support:Gable end made of prelaminated particle board,Frame material for work station:Other wood,Material of table top:Prelaminated particle board,Material of tiles for top:laminate,Material of intermediate tiles:laminate,Material of bottom tiles:prelaminated particle board tile,Length of table top (main frame) ±10 mm(main frame):1500 mm,Length of table top (Return Frame)± 10mm:1500 mm,Depth of table top ± 10mm:600 mm,Overall height of work station partition ±10mm:900 mm,Thickness of side partition/panel ±2mm:23 mm,Thickness of main frame ±5 mm:25 mm,Size of drawer unit(WidthXDepthXHeight) ±10mm:390 X 440 X 147 (mm),Size of file box (WidthXDepthXHeight) ±10mm:390 X 440 X 296 (mm),Warranty period in number of years:2.All workdone as directred by engineer-in-charge.

Providing and commissioning GODREJ INTERIO black 3 Seater 18 mm teak plywood sofa,Type of Sofa and Backrest Seat and Backrest are permanently fixed with the frame Structure,Frame Covering:Fully Upholstered,Backrest Cushion Material:foam,Density of Cushion of Backrest Material (Kg/Cubic M):28,Covering Material for Seat and Backrest:Leatherite,Frame Structure Material and size (±1 mm):18 mm teak plywood,Seat Cusion Material :foam,Density of Cushion of Seat Material ±3 (Kg/Cubic M):30,Type of Spring in the Base / Seating:Zig zag,Length of Three Seater Units in mm (±10 mm):2050mm,Depth of Sofa Units in mm (±10 mm):900,Sofa Height (Without Back Cushion) ±5 (mm):700 millimeter,Sofa Height (With Back Cushion) ±5 mm:800 millimeter,Arm Width ±5 (mm):120 millimeter,Arm Height ±5 (mm):710 millimeter,Seat Height (With Seat Cushion) ±5 (mm):450 millimeter,Sofa Leg Height ±2(mm):150 millimeter,Sofa Leg Width / Diameter ±2 (mm):35 millimeter,Seat Cushion Length ±5 (mm):1700,Seat Cushion Width ±5 (mm):510,Seat Cusion Thickness ±5 (mm):125,Backrest Cushion Length ±5 (mm):1050,Backrest Cushion Width ±5 (mm):508,Backrest Cushion Thickness ±3 (mm):175,Thickness of Foam in arms ±2 (mm):50,Thickness of Foam in back ±2 (mm):152 millimeter,Thickness of Foam in front ±2 (mm):40 millimeter:Thickness of Foam in sides ±2 (mm) :10 millimeter.Colour finish Black,Warranty 1 year.

CENTER TABLE Rectangular CENTRE TABLE with Flat glass Top of 1194mmX584mm,Number of storage under top:Single storage in upper portion,Top material:Flat glass ,Frame material:Teak wood,Dimension of Top (length X Breadth) ±20mm:1194mmX584mm,Height of centre table ±10 mm:430 millimeter,Thickness of top material (+/-2 mm):10 millimeter Thickness of frame material (+/- 1 mm):36 millimeter,Warranty period in number of years:2

Bidder Name

Amount

Shiv Shakti Industries(GSTN-NA)