SPL REPAIR TO BLDG NO T-89, T-90, T-91, 2 RA NORTH AND PROVN OF OVERHEAD SHED UNDER AGE B/R-II AT GE JHANSI

Amount

Dismantling of wall / ceiling boards of any thickness including cover fillets etc, complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

M&L for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) including demolition of existing water proofing complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Applying a coat of aluminium paint complete all as sppecified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard dense soil complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of brick/stone masonary built in cement mortar incl all quoins arches pillars etc complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

Taking down Chowkats or frames Not exceeding 1.5 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

M&L for brick work with sub-class B bricks straight or curved on plan exc 6 Mtr mean radius built in CM (1:6) complete all as specified and directed.

M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over 1 mm putty and a coat of chalk whitening primer preparating to make the surface to be plain and smooth before primer complete all as sppecified and directed.

Preparing newly plastered surfaces of wall and applying two coats of weather proof exterior grade emulsion over and including a coat of exterior grade cement based primer complete all as specified and directed.

M&L for Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqmcomplete all as specified and directed.

Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide primer complete all as specified and directed.

Complete removal of exisiting treatment, washing and rubbing of old distempered surfaces and applying two coats of oil bound distember (acrylic) over 1 mm putty and a coat of chalk whitening primer preparatory to distemering complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete.all as sppecified and directed.

M&L for Coloured Glazed ceramic tiles 300x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick redering in CM 1:4 on wall complete all as specified and directed..

M&L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per item No 25.00 above but for skirting complete all as specfied and directed.

M&L for machine cut Kota stone slab flooring 20-25 mm thick and laid over and incl 20 mm thick screed bed in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting / Griding / mirror Polishing on Kota stone as per local trade practice, complete all as specified and directed.

All as per Ser item No 27 above but on vertical surfaces such as skirting/dado over 10mm thick CM rendering in CM 1:4. complete all as specified and directed.

M&L for Granite 20 mm thick in one single piece over including 10 mm thick CM 1:4 (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rubbing and polishing complete including rounding outer edge all as specified and as directed.

All as per Ser item No 29 above but on vertical surface, skirting/dado over 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

S&F in repair Aluminium Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400 mm including PVC waste pipe 32mm dia 600 mm long, CP waste coupling and MS brackets complete all as specified and directed.

Supply & Fix in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete all as specified and directed.

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removed from site complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removed from site complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors with hooks complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors with hooks complete all as specified and directed.

Taking down eaves gutter and rain water pipes including all fittings any size and pattern complete all as specified and directed.

S&F in repair of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as specified and directed.

S&F in repair PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore conceald stop cock fancy type,chromium plated with long shank and cup screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all as specified and directed.

S&F in repair SS grating of square/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.

S & F in repair Chromium plated overhad shower including Shower Arm with or without swivel joints, any size, including fixing to steel pipe complete all as specified and directed.

S&F in repair SS Towel Rail 600mm Long fixed with and including chromium plated brass screws complete all as specified and directed.

S&F in repair of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as specified and directed.

M&L for mild steel framed work section as in door or gates or grills of angle or other section with gusset plates,rails braces etc /windows chowkhats/Shutter frame of steel gate of grade Fe-290 (Gde E-165) including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) for bed block for fixing of chowkhats, cills ,pre-cast lintel n.exc 1.5mtr,coping,benching etc complete all as specified and directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 5 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window n exc 2 sqm) comprising of uPVC multi chambered rame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed. Note : Glass or wiremesh shall be paid separately. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in epth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)., supplying & fixing in opening as per specification & drawing complete all as specified in SSR Part-II 2020 section 8.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

M&L for powder coated aluminium frame for doors, windows, ventilators with one or more rebates, fabricated out of powder coated aluminium hallow square or rectangular section of required size incl necessary joining cleats, fixing screws etc complete, having size of frame for doors 100mm x45mm x 3.18 mm thick; for window 104mm x 45mm x 3mm thick; for ventilators 59mm x 33mm x 2.5mm, complete all as specified and directed.

M&L for powder coated aluminium door shutters, aluminium section for top rail and styles 85mm x 45mm x 2.0mm thick; bottom rail 100mm x 45mm x 2mm thick and lock rail 100mm x 45mmx 2.0mm thick incl necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, powder coated aluminum hinges, powder coated aluminum snap beading, screws etc, complete all as specified and directed.

S&F powder coated aluminium window shutter Sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F Aluminium powder coated window guards framed with aluminium window section for window guards 4mm dia expanded shape fixed with wall fastner to opening complete all as specified and directed.

M&L for powder coated aluminum window shutters, side hung type without sash bars, aluminium sections for frame weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber packing, powder coated aluminum snap beading, screws, powder coated aluminum fittings such as peg stays 150mm long (01 No), hinges type B-21 100mm long (02 No), suitable handle (01 No), complete all as specified and directed.

S&F mortice lock of size 100mm, 4 lever type, duly fixed in aluminium door, complete all as specified and directed.

M&L for aluminium (Extruded section) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg complete all as specified and as directed.

M&L for double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S&F of 25 micron glass film sticked to glass panes as per manufacturer's instruction, complete all as specified and directed.

S&F of glass, tinted type, 5.0 mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified and directed.

S&F of 12 mm thick toughned clear glass door, partition automatic door with and including chrome or SS finished profiles, roller hanger, patch fittings, hinges ,handles, handrail etc with and incl all respective accessories , complete all as specified and directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area n.exc 1.00 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & complete all as specified and directed. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be cceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 3mm thick sheet glass frosted/figured and pin headed glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

M&L in repair for Aluminium anodised curtain rod 25mm dia with caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed.

M&L for factory made PU coated, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion is is included in quoted rate.

M&L for PCC Type B-0, 1:2:4 (12.5 mm Stone Aggregate) , in copings and sub base etc complete all as specified and directed.

Removing excavated material not exc 50 m and depositing where directed at a level not ext 1.5 m complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed.

Dismantling of Framed timber scantling 40sq cm and over in section in any position complete all as specified and directed.

Dismantling of Framed timber fillet, rails, post, rafters, purlin etc n. exc 40sq cm in section in any position complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.

S&F of 10-12mm thick plaster of paris ceiling (Gypsum anhydrous board) to flat surface over metal frame work and reinforced with G.I. wire mesh including putty, distemper and seemless finish in all respect etc complete all as specified and directed (Note: The rate of fillets, metal frame work and G.I. wire mesh are included in quoted rate)

M & L for filleting of section exc 25 sq cm but not exc 50 sq cm, in any position and to any shape in cement mortar 1:4 including excavation and earth work and all mitres, stops, etc complete all as specified and directed.

M&L for mild steel hold fast and similar small articles conforming to Fe-290 Gde-165, complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D2 (40 mm graded aggregate) in foundations, filling and mass concrete, complete all as specified and directed

M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, Fe-410-W (Gde-E-250) quality-B, complete all as specified and directed.

Returning filling in trenches including spreading leveling and well ramming with water complete n.exc 25 cm thick in each layer in soft/loose soil complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points:-

One light / fan/ bell / buzzer /exhaust point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Serl item No 97 above but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of modular electrogalvanised concealed boxes and cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly all as specified and directed (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :-

One light point controlled by one switch

One Exhaust fan point controlled by one switch.

One ceiling fan controlled by one switch

One Bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Srl item No 99 above but with 4.0 sq mm FRLSH copper wire with 4.0 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length.

All as per Ser item No 101 above but 2 runs X 4 Sqmm + 1 run X 4 Sqmm complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Notes for item No 97 to 102.00 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F of Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F of Socket 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

S&F of Switch piano type, single pole, one way, 15 amps, 230 volts, complete all as specified and directed.

S&F of Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

S&F of angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

S&F of Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S & F of 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix in replacement of LED lights fitting 1 x 20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix LED in replacement of building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and as directed.

Supply and Fix of Desert Cooler, electric driven having nominal air flow capacity of 6000 cu.m per hour (or nearest size) Steel body complete all as specified and directed.

Supply and fix in replacement of LED luminaire 600 mm x 600 mm of warm white/cool white colour, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fix in replacement of MCB distribution board, VTPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix in replacement of MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

Supply and fix MCCB, 125A, 16 KA, 4 Pole complete all as specified and directed.

S& F MCB TPN 63 Amp, 10 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

S& F MCB SPN 40 Amp, 10 KA, 'C' curve, 230 V, 50 Hz complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 230 V complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 25 sq mm 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down existing service cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of HDPE pipe and getting out in any type of soil complete all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fix of Modular switch 1 way 6A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix of Modular switch 1 way 16A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix of Modular Socket 6A/16A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

Supply and fix of Modular Socket, 6A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

Supply and fix of Modular Bell push 6A 1 module, 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable bell push of any description complete all as specified and directed.

S&F electric bell of DINGDONG type, 240 volts, single pole and making all necessary connections, complete all as specified and directed.

S & F 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix of integrated LED batten 20 watt, 4 feet long, full white / warm white shade in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of Decorative wall light fixture made up of Polycarbonate with and including 7W retrofit LED lamp, full white of approved model including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix LED batten 9W/10W (2 Feet) complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fix in replacement of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 12 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

S& F MCCB TPN 100 Amp, 16 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

Supply and fix in replacement of ceiling fans complete with blades, down rods hand held remote controlled and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

M/S A.R BUILDERS

M/S Ritu Tandon

S GOURAV PRAKASH ENTERPRISES

S R BUILDERS

Raja enterprises