SPECIAL REPAIR TO BUILDING NO T-441 AND PROVN OF STORE FOR EM INSTALLATION AND SECURITY LIGHT AT JANGLOTE UNDER GE BASOLI

Amount

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and directed...

M&L PCC 1:4:8 type D-2 ( Using 40mm graded crushed stone aggregate ) in foundation filling and mass concrete complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L for M-20 Nominal mix as in beams, cantilevers, bressummers, lintels over 1.5m span (using 20mm graded crushed stone aggregate) complete all as specified and directed .

TMT Mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed .

All as per item No 11 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Form work to edges of concrete flats, breaks in floors, openings in concrete walls,floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 20 cm wide for rough finished flat surfaces of concrete complete all as specified and directed.

Rendering 15mm thick on other than fair faces of brick work in cement mortar 1:4 finished surface even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Spreading, levelling, watering and well ramming in layers not exc 25 cm thick each as in floor as in soft / loose soil. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft / loose soil. complete all as specified and directed.

Removing excavated material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L hardcore of broken stone or boulders. gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick. Watered hand rammed to a true surface, complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L machine cut kota slab fooring 20-22mm thickness over cement screed base laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L machine cut kota slab 15-20mm as in steps, risers, skirting, dado etc laid and jointed with gray cement slurry mixed with pigment to matches the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 450x300mmx7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 10mm thick rendering in CM 1:4 including taking down cement plastercomplete all as specified and directed.

Plain cement concrete 75mm thick 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub floor, sub base complete, all as specified and directed .

M&L for providing 75mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

S&F steel window/ventilaters including 10mm Sq bar grill factory made out of box type frame and shutter (double shutter, one for glazing another for fly proofing) made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings all as per drg No CEPZ/TD/27/13 Sh 1/4 to 4/4 all as complete all as specified and directed.

M&L for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified and directed..

M&L for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed..

S&FGalvanised MS wire cloth 0.46mm nominal dia of wire and average width of aperature 1.18mm, complete all as specified and directed..

Supply and fix for Aluminium alloy, anodised, sliding door bolt 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed,complete all as specified and directed.

Supply and fix for Extruded aluminium alloy handles fabricated type anodised and fixed, 150 mm size complete, all as specified and directed.

Supply and fix for Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt,complete all as specified and directed.

M&L for applying three coats of white washing on walls including preparation of newly plastered surfaces complete all as specified and directed.

M&L for preperation of new plastered surface of wall and applying two coat of cement base paint over a coat of primer, complete all as specified and directed.

M&L for preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint.over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Supply and fix for Rolled Mild steel section as in main and cross beams, hip and rafters, purlins, trusses vertical member where connected common rafters and fixed with angle cleats or other connecting plates in Gde Fe-410S ,complete all as specified and directed.

Material and labour for preparation of old steel and iron surfaces exceeding 10 cms width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling asbestos cement, corrugated or semi-corrugated sheets in roofs complete all as specified and directed.

Supply and fix for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for Rendering 15mm thick in cement mortar 1:4 and finished even and smooth without using extra cement and preparation of new plastered surfaces and applying two coats of cement base paint on walls over a coat of primer including taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Rendering 15mm thick in cement mortar 1:6 and finished even and smooth without using extra cement and preparation of new plastered surfaces and applying one coat primer and two coats of distemper oil emulsion and 3mm thick wall putty including taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MS tube for steel work in tubular trusses including columns purlin rafter etc complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. -240 and it is painted one coat of zinc chromate primer paint (including preparation of surface) complete all as specified and directed.

Supply & Fix partition wall with aluminium frame work partially glazed witj 4mm thick plain glass and partially panelled with 12mm thick pre-laminated particle board both side decorative laminated using aluminium section of size 63.5mm x 38.1mmx1.80mm for horizontal post single face (bottom and top), 63.5mm x 38.1mm x 1.80mm horizontal (middle) and vertical posts double face and corner post with necessary fittings and fixed to walls, floor and ceiling complete all as specified. Note :- Aluminium section size specified above if not available in the market next immediate higher size of same make shall be provided without any extra cost to the Govt.

Point wiring with 1.5 Sqmm (nominal area) copper conductor cable FRLS (Multistranded) PVC insulated and unsheathed in and incl PVC conduit concealed with pressed steel terminal boxes of adequate size with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable FRLS (multistranded) PVC insulated and unsheathed with colour code earth wire to common earth dolly complete all as specified. Note (a) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall ,floors etc.

Supply and fix switch piano flush type single pole one way 5 Amps complete all as specified and directed.

Supply and fix MCB SP 6-32 Amps 240 Volts complete all as specified and directed.

Supply and fix MCB SP and neutral(SPN) 63 Amps 240 Volts complete all as specified and directed.

S&F sheet metal powder coated versatile double door SPN distribution board, 8 way suitable for MCB’s fitted with copper bus bar rated 200 Amps, neutral link, earth bar and din rail suitable for use on 240 Volt, 50 Hz complete all as specified and directed.

Supply and fix in replacementLED recess mounting powdercoated white CRCA full glow panel 45 watt 2x2 ft incorporated with all fixing arrangements complete with all accessories internally pre-wired and Make : Crompton cat part No: (CYGNUS-C/45W/2X2/W or equivalent in Philips/Wipro/ Bajaj/Halonix incl all necessary electric connection with three core copper cable 23/0.0076 complete all as specified and directed.

Supply and fix for DWC high densiy polyethylene pipes having dia 63/50 as per site requirement having corrugation on the wall and plain surface on the inner wall conforming to IS: 14930(Part I & II) for protection of underground cable laidalong pole/along wall/in PCC on GL/roof complete all as specified and directed.

Supply and Laying in trenches or passing through pipe or fixing to pole/wall UG cable XLPE, insulated,armoured heavy duty electric cable with aluminum conductor,1100 Volts grade,10 Sq mm X 2.0 core cross section area including takingout existing cable complete all as specified and directed.

Supply and fix LED flood light of cap 150watt Energy saving and enviromental friendly long life verstale pressure die cast aluminium with protection IP-66 made out of pressure die cast aluminium housing suitable lens and toughened glass with high power LED as light source complete with the provision of double driver and additional surge protector of capacity 10 kv including flexible pipe for connection protection all as specified and directed

BALKRISHAN GUPTA AND SONS

Neeraj Enterprises

Walia trading co

Standard engineers