ADDITION ALTERNATION AND SPECIAL REPAIRS TO CERTAIN CABINS OF BUILDING PO 15 AT WNC O MESS AND ADDITION ALTERNATION AND SPECIAL REPAIRS TO ELBOW BENDER BAR AT WNC O MESS AND WATERPROOFING OF DINNING HALL AT WNC O MESS COLABA MUMBAI AND REPAIR REP

Amount

Guniting / Shotcreting concrete surface with an average thickness of 25 mm with cement mortar applied with compressor including supplying, fitting , fixing of wire mesh and guniting equipment after cleaning surface and spraying area with epoxy @ 1.0 kg per 1.50 sqm of surface area complete as per CI.2807 of specification of roads & bridge works published by IRC incl. cost of preparation of surface, supply of all materials and fuel, hire charges of machineries and labour etc complete all as specified and directed by Engineer-in-Charge.

M&L for Wire netting of galvanised steel wire 1.40mm dia 20mm size of mesh fixed with tinned tacks of wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for provision of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed by Engineer-in-Charge.

Chipping, removing carefully concrete work by low impact hammer, breaker without damaging the structure & cleaning and disposal of debris out side the premises etc complete all as specified and directed by Engineer-in-Charge. Hard concrete shall not be removed by force.

Clean existing reinforement with/ rotary wire bruch, making the surfaces free from loose material dirt etc, complete, applyin g two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed by Engineer-in-Charge.

Carryout application of bi-polar migratory corrosion inhibitor EPCO-KP-100/Protectsil/ CIT/Ferogard 903 on concrete surface (This inhibitor shall have migratory kind of properly which permits the material to a vertual extent of 100mm, through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack anode as well as cathode, which is purely alkaline in nature (pH-9.5), so it has no carcinogen activity with concrete complete all as specified and directed by Engineer-in-Charge.

M&L for drilling and fixing Rohibb Teflon nozzoles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at the intervals of 500 center to center in staggered manner or as directed by Engr-in-Charge in RCC structural element work shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia, Rohibb Teflon nozzles in cleared holes. External end of nozzles to be machine to receive outlet of grouting gun. Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for minimum 12 hours. (iii) Cutting the nozzles. Cut the nozzles by chiselling after completion of grouting without damaging structural elements.

M&L for injecting of site cement slurry grout, in ratio 1:2 (1 Cement, 2 water) including super plasticizer (Supercom-100) 250 ml/50 Kgs. Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/ specified grout by means of pump at a pressure of 0.5 Kg/CM2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled. (For repair to slab).

M&L for injecting low viscosity MONOPOL (3-5cps) high molecular weight monometer by pressure and using mechanized injector gun with accessories till nozzles rufeses to accept the grout, including , mixing of materials, mixing of material components (Part a&b) in the required quantities as per manufacturer's instruction by weigh batching. Grouting maintain the pressure at exit (0.5 to 1.0 Kg/ Cm2) by monitoring pressure guage at exit. Grout the material through prefixed nozzles in the structural elements @ 100ml per nozzles. (Beam & columns)

Providing and applying structural grade EPIBOND-21-LP prior to application of any type mortar plaster confirming to ASTM-C-882-91 (Arizona slant shear test) to ensure bond between old concrete and new concrete

Providing and applying jacketing around columns beam slabs with micro concrete (Molith MC) M40 including all lifts, shuttering, drilling, holes and fixing shear anchor as per specification complete. Note :- Reinforcement shall be measured and paid saperately (NOTE : Rates including jacketing, formwork and micro concrete)

M&L for Building up the profile of structural members by using latex additives(MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling etc complete all as specified and directed by Engineer-in-Charge.

Note:-Water proofing compound shall be measured separately under respective item.

M&L for preparation of old/new plastered surfaces and applying two coats Plastic emulsion paint on wall & ceiling over a coat of alkaline resistent primer over and including a coat of putty to plumb the existing surface, complete all as specified and directed by Engineer-in-Charge. Make:- Asian , Berger ,Nerolac.

M&L for preparation of old plastered surfaces by complete removal of existing treatment and applying two coats Plastic emulsion paint on wall & ceiling over a coat of alkaline resistent primer over and including a coat of putty to plumb the existing surface, complete all as specified and directed by Engineer-in-Charge. Make:- Asian , Berger ,Nerolac.

M & L for preparation surfaces of new plastered surfaces wall/chajja and applying one coat of acrylic exterior primer and apply two coats acrylic emulsion exterior grade (100%) etc all as specified & as suggested by the manufacturers at any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge. Make:- Asian Ultima, Berger all weather anti dust , Nerolac excel total.

M&L for preparation of old decorated surfaces of walls by scrapping old paint with steel wire brush or by any means, washing the surface throughtly and applying two coats of acrylic emulsion exterior grade (100%) over a coat of primer complete including necessary scaffolding for any position/height all as specified and directed by the Engineer- in- Charge. Note :- (a) Acrylic painting shall be done with rollers. Make:- Asian Ultima, Berger all weather anti dust , Nerolac excel total.

M&L for preparation of old painted wood or wood based surfaces of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint with smooth roller finish etc complete all as specified and directed by Engineer-in-Charge. MAKE : Asian ( Apcolite) or Narolac ( Hi- gloss) or Berger (Luxo Hi- glossl)

Material & Labour for preparation of old painted on steel based surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint with smooth roller finish etc complete all as specified and directed by Engineer-in-Charge. MAKE : Asian ( Apcolite) or Nerolac ( Hi- gloss) or Berger (Luxol Hi- gloss)

M&L for preparation of new plastered or unplastered surfaces and apply two coat of oil bound distemper on wall over a coat of primer complete all as specified and directed by Engineer-in-Charge. MAKE : Asian ( Apcolite) or Narolac ( Hi- gloss) or Berger (Luxo Hi- glossl)

Preparation of new plastered or unplastered surfaces and apply two coat of oil bound distemper on Ceilingover a coat of primer complete all as specified and directed by Engineer-in-Charge. MAKE : Asian ( Apcolite) or Narolac ( Hi- gloss) or Berger (Luxo Hi- glossl)

Material & Labour for complete removal of existing treatment by washing down and smoothing old surface of walls including scrapping and applying two coats of oil bound distemper over a coat of primer over layer of smooth POP/Putty finish as required pruning 3mm thick strictly as per manufacture instruction with smooth roller finish ,complete all as specified and directed by Engineer-in-Charge. Make of OBD :- Asian , Berger ,Nerolac.

M&L for preparation of new plastered or unplastered surfaces of walls including scrapping and applying two coats of oil bound distemper over layer of smooth Putty finish as required punning 3mm thick over a coat of primer strictly as per manufactuure instruction with smooth roller finish complete all as specified and directed by Engineer-in-Charge.

M & L for complete removal of existing treatment by scraping down wall surfaces and applying 3mm thick wall care putty on wall and applying two coats of 'Lustre' paint of approved quality with Priming with alkali- resistant primer on wall etc complete all as specified and directed by Engineer-in-Charge.

Material & Labour for complete removal of existing treatment by washing down and smoothing old surface of Ceiling including scrapping and applying two coats of oil bound distemper over a coat of primer over layer of smooth POP/Putty finish as required pruning 3mm thick strictly as per manufacture instruction with smooth roller finish ,complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surfaces of ceiling including scrapping and applying two coats of oil bound distemper over layer of smooth Putty finish as required punning 3mm thick over a coat of primer strictly as per manufactuure instruction with smooth roller finish complete all as specified and directed by Engineer-in-Charge.

M&L For prepration new wooden ceiling surfaces and applying plaster of paris punning to get plumb of avrage thickness of POP etc complete and applying two coat of Luster paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered or unplastered surface by applying 3mm thick wall care putty on wall & Priming plastered and other surfaces with alkali- resistant primer on wall etc complete all as specified and directed by Engineer-in-Charge.

Dismantling of boarding, any description, fixed in any position with nail etc complete and removing debris outside MOD land complete all as specified and directed by Engineer-in-Charge.

S&F of clean sawn first class hard-wood timber framed and fixed in scantlings and frames to receive the shutters etc complete all as specified and directed by Engineer-in-Charge.

M&L for 18mm thick plywood grade BWR ,fixed with screws to timber frame work in shutters including beading etc complete all as specified and directed by Engineer-in-Charge.

M&L for 18mm thk Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work etc complete all as specified and directed by Engineer-in-Charge.

M&L for 0.9 mm thick decorative laminate type 1, of surface finish , colour and pattern as approved by GE,fixed with approved adhesive as per manufactures insrtuction etc complete all as specified and directed by Engineer-in-Charge.

S&F of 35mm thick IInd class hard wood factory made glazed and skelton shutters open rebated and prepared to receive gauge/glass cut and metered beads and divided into square with plain chamfered or rounded metered and rebated sash bars any numbers size of members of shutters for door and ventilator complete all as specified and directed by Engineer-in-Charge.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M & L for DGVT coloured vitrified tiles of area exc 0.36 Sqm, 10mm thick, laid in flooring, with & including 5mm thick adhesive of Ferrouscrete (FERRO-1122) / Fevimate XL- Pidilite / Gold star of Bal Endura , Dr Fixit or equivalant including necessary roughning of existing PCC flooring & levelling the floor if required, grouting the joints with white cement complete all as specified and directed by Engineer-in-Charge. Note : Quality , Shade , pattern of DGVT coloured vitrified tiles shall be as approved by GE Make:- Somany ,Orient Bell, kajaria.

M & L for DGVT coloured vitrified tiles of area exc 0.36 Sqm, 10mm thick, laid in skirting, over & including a backing coat of 10mm thick in CM 1:3, complete and making nosing at right angle corner, including levelling the wall, complete all as specified and directed by Engineer-in-Charge. Make:- Somany ,Orient Bell, kajaria.

M & L for 18 to 20mm thick Granite (of any type) tiles machine cut, in cills, jambs, skirting/ dado laid over cement screed of 20mm thk with CM 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing etc complete all as specified and directed by Engineer-in-Charge.

M & L for Polished granite stone slab 20 mm thick coloured as in cooking platform/door sills ,slabs, partitions set and jointed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including moulding at front edge or both edges including dismantling complete all as specified and directed by Engineer-in-Charge. Note : Quality , Shade , pattern of granite all shall be as approved by GE

M & L for Makarana White Marble work 18 to 20mm thick (table rubbed and polished) fixed in flooring with 20mm thk cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade etc complete all as specified and directed by Engineer-in-Charge. Note : Quality , Shade , pattern of Marble all shall be as approved by GE

M & L for Makarana White Marble work 18 to 20mm thick (table rubbed and polished) for wall lining (veneering to wall) 25mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade etc complete all as specified and directed by Engineer-in-Charge. Note : Quality , Shade , pattern of Marble all shall be as approved by GE

M & L Glazed ceramic rectified tiles in vertical surfaces of size 350x 250x 7mm/ 450X 350X 7mm thick including over 10mm thick Screed bed or bedding layer in CM 1:4 for laying tile finishes set and jointed in neat cement slurry and pointed in white or coloured cement to match including dismantling complete all as specified and as directed by the Engineer-in-Charge. Make: Somany, Kajaria, Orient bell.

Preparation of existing mosaic cement tiles flooring and polishing with machine/hand to surface and pointing of joints to match the colour complete all as specified and directed. Make : Mehtab , Nitco , National

Taking down existing cement or cement lime plaster and preparation of surfaces of walls/ceiling of any description incl racking out joints backing for scrubbing down with water and any height including necessary scaffolding and removing debris out side MD land complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5 mm thick cement plaster in brick or concrete surfaces using ready mix mortar as on ceiling finished even and smooth any height including necessary scaffolding complete all as specified and directed by Engineer-in-Charge.

M & L for rendering 10 mm thick cement plastering on brick or concrete surfaces in CM (1:4) finished even and smooth without using extra cementcomplete all as specified and directed by Engineer-in-Charge, as in ceiling.

M&L for rendering 15mm thick CM 1:6 on fair face of brick work or concrete surfaces of walls and finised surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for 10mm thick rendering in cement and sand mortar 1:4 on roof padding concrete surface for levelling course rounded or chamfered on edges, slopping mixed with water WPC @ 2% by weight of cement, finished even & smooth surface without using extra cement complete all as specified and directed by Engineer-in-Charge. NOTE : (WPC shall be measured and paid seperately)

M&L for rendering 20mm thick on other than fair face of brick work or concrete in two layer first is 15mm thick CM 1:4 and seconed 5mm thick cement mortar 1:4 mixed with water proofing powder at the rate of 2% of cement or as per manufacturers instructions and any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge. Note:- (i) Water proofing compound shall be measured separately under respective item. (ii) Water proofing compound shall be as approved by the GE.

Supply only integral water proofing compound powder confirming to IS-2645 complete all as specified and directed by Engineer-in-Charge. Make : Scot No 1 , Dr.Fixit , Pidilite , Tiki Tar Danosa as approved By GE.

M&L Plastering in ready mix mortar, 15mm thick on fair faces of brick work or concrete surfaces of walls finished fair and even any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

M & L for Plastering 15mm thick on brick ,concrete or dubbed wall surfaces in cement mortar 1:4 finishing even and smooth without using extra cement to fascia,fins,parapet, soffits of chhajjas etc and similar likes at any height including necessary scaffolding, ladder, formork ; including taking down cement / lime plaster of any description on brick or stone walls etc, raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M & L for Plastering 10mm thick on ceiling concrete surfaces in cement mortar 1:3 finishing even and smooth without using extra cement etc and similar likes at any height including necessary scaffolding, ladder, formork ; including taking down cement / lime plaster of any description on brick or stone walls etc, raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

S&F powder coated (50Micron minimum thickness) aluminum frame & shutter for door ,windows, ventilators etc.with one or more rebates including jointing cleat for fixing etc.fixed type/louvered window or ventilator without sash bar,aluminum including necessary joining cleats,glazing clips,rubber packing,anodised aluminum snap beading,screws, sliding rollers, Rubber gasket etc.compleate all as specified compleate all as specified. Note:a)Glazing shall be measured seperately. b)Item shall be paid as per weight of alluminium section.c)the rate quoted shall be inclusive of neoprene beading,glazing clips,screws, etc., as required which shall not be measured for arriving the weight.d)the rate shall be inclusive of the locking arrengement including complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing surface area.

S&F in repair aluminum anodised GRILL (Deco grill DG 103 of 7.5 mm thick of M/s ELESAR FOCCHI Ltd.) fixed with suifable 'F' section No. 8584 15.30 x 23.40 x 1.40mm fabricated and rivetted to aluminum windows, complete all as specified and directed by Engineer-in-Charge.

Supply and fix 5.50 mm thick plain glass exc 0.5 SQM in EACH pane fixed to aluminium windows and iron frame complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium wire cloth 0.45mm nominal dia of wire and average width of operature 1.40mm and fixed to aluminium Vent/window all as specified and directed Engr-in-charge cost of aluminium beads and neoprene included in relevant item of aluminium window) in repairs complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of size exc 2sqm each complete all as specified and directed by Engineer-in-Charge.

Refixing of Shutters in same opening any description exc 2 sq. m each. 'refixing' includes taking down, easing and adjust- ing and also refixing builders hardware as required including renewal of unserviceable screws, etc. Renewal of builder's hard- ware articles, if specially ordered, shall be paid for at 'supplied only' rates complete all as specified and directed by Engineer-in-Charge.

S & F of Brass, sliding door bolt 300 mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engineer-in-Charge.

S & F of Brass, sliding door bolt 250 mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engineer-in-Charge.

S & F of Brass barrel tower bolt with barrel of extruded section 300mm long complete all as specified and directed by Engineer-in-Charge.

S & F of Aluminium anodised barrel tower bolt of extruded section 150mm long complete all as specified and directed by Engineer-in-Charge.

S & F of 300mm long extruded Brass handle fabricated type polished complete all as specified and directed by Engineer-in-Charge.

S & F of 100mm long extruded Alluminium anodised handle fabricated type polished complete all as specified and directed by Engineer-in-Charge.

S & F of 100mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-1 complete all as specified and directed by Engineer-in-Charge.

S & F of 75mm long Butt hinges, heavy weight, cold rolled mild steel and fixed etc complete all as specified and directed by Engineer-in-Charge.

S & F of Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed of Aluminium (extruded) Section complete all as specified and directed by Engineer-in-Charge.

S&F of Aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded such or cast aluminum alloy complete all as specified and directed by Engineer-in-Charge.

Supply and fix 8mm thick frosted glass ; n exc 0.5 sqm in each pane fixed to wooden frame structure and fitted with required U shape clamp & screw material and glazing with oil putty etc complete all as specified and directed by Engineer-in-Charge. (Note:- Wooden Frames structure shall be measured and paid seperately.)

Supply and fix 8mm thick frosted glass ; exc 0.5 sqm in each pane fixed to wooden frame structure and fitted with required U shape clamp & screw material and glazing with oil putty etc complete all as specified and directed by Engineer-in-Charge. (Note:- Wooden Frames structure shall be measured and paid seperately.)

S & F in repairs clean sawn first class hard-wood timber in ceiling including fixing to frame and other required accessories for counter etc complete all as specified and directed by Engineer-in-Charge.

S & F in repairs clean sawn first class hard-wood timber in scantlings for serving counter table including wooden moulding and other required accessories for counter etc complete all as specified and directed by Engineer-in-Charge.

Roughening/cleaning surfaces of roof with wire brush, sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engineer-in-Charge.

Providing in repairs water proofing treatment with APP (Atactic polypropylene) modified polyester (bituminous) membrane reinforced of 3.5Kg/Sqm with non woven polyester mat of weight 160 gms/sqm as center core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer @ 0.25 Kg/Sqm over roof (An overlap of 100mm and 150mm shall be provided on sides and ends respectively and the APP membrane shall be taken up to minimum 200mm on vertical surfaces) and applying two coats of bituminous aluminium paint on APP sheet incl removal of old damaged APP sheets and removing from MD land complete all as specified and directed by Engineer-in-Charge. Make : Pidilite , IWL, STP , Tiki Tar Danosa as approved by GE.

Preparing of old/new surfaces of walls/ceiling (of projected Cup boards) washing the surface thoroughly, filling the cracks, creaves with crack filling compound as suggested by the manufacturers and applying two coats of Rain coat (shade to match the existing paint) complete all as specified and directed by Engineer-in-Charge. NOTE : Make shall be as approved by GE.

M&L French polishing on wooden surfaces of any description width or girth including cleaning and prepairing the surfaces including a coat of wood filler on old surfaces with one or more coat complete all as specified and directed by Engineer-in-Charge.

Taking down CI/rain water pipes/PVC pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc., including cleaning etc complete all as specified and directed by Engineer-in-Charge.

S&F 110mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including GI clamps of approved shape and size approved by GE at any height, any location, any floor including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

S&F 110mm dia PVC (SWR) bends/shoes any radius fixed to pipe at any location/height including necessary scaffolding etc complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm dia PVC (SWR) pipes single socketed,in any length with rubber ring joints, fixed in wall including GI clamps of approved shape and size approved by GE at any height including necessary scaffolding complete all as specified and as directed by Engineer-in-Charge.

S&F 75mm dia PVC (SWR) bends/shoes any radius fixed to pipe at any location/height including necessary scaffolding etc complete all as specified and as directed by Engineer-in-Charge.

S & F 40mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix as in repair 15 mm bore pillar tap, cast copper alloy, with capstan head, chromium plated, screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F of Sink with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm , bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

S & F Mild steel framed work (Fe-410-O) or (Fe-310-O) such as grill, gratings, sheet including welding to purpose made hinges etc with the ends of bars shoulders or riveted or forged into spikes framed guard bars railing and similar works fixing with bolt etc ,complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections and removing from store of following sizes, complete all as specified and directed by Engineer-in-Charge.

(a) 25 mm bore

(b) 15 mm bore

Supply and fix of steel water tubing galvanised medium grade (ISI Marked) of following size, with all fitting fixed complete to walls and ceilings or laid in floor/wall/ceiling (in high rise building including scaffolding) ,complete all as specified and directed by Engineer-in-Charge.

(a) 25 mm bore

(b) 15 mm bore

Demolition of brick work , stone masonary , cement concrete (unreinforced) of any description and in any position not otherwise specifically provided and removed of debris outside MD land complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided and removed of debris outside MD land ,complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub class B bricks, straight or curved on plan exc 6.0 m mean raduis and built in cement mortar (1:6), incl demolition of old brickwork built in CM complete all as specified and directed by Engineer-in-Charge.

Material and labour for half brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:2:4 type B- 0 (12.5 mm graded agg) in roof padding concrete, kerbs or mud stops, rounded or chamfered on edges all around at the junction of parapet and the roof slab complete all as specified and directed by Engineer-in-Charge.

B P ENTERPRISES