PROVN OF POL STORE, MODERN GREASE TRAP AT MESSES AND SOAKAGE WELL AND SEPTIC TANK FOR OTM ACCN AT AF STN DINJAN UNDER GE (AF) MOHANBARI

Amount

M&L for brickwork with subclass'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with subclass'B' bricks, straight or curved on plan exc 6m mean radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for brickwork with subclass 'B' Bricks, laid flat, in floors, Bedded and jointed in cement mortar 1:6 and pointed in cement mortar complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces with out extra cement in cement mortar 1:6 complete all as specified and directed.

M&L for two coat of oil bound distemper over a coat of primer with wall care putty (3mm)with even and smooth finish over prepared surface of wall complete all as specified and directed.

M&L cement concrete type D2 1:4:8 (40mm graded stone aggregate) as in sub base/ floor complete all as specified and directed.

M&L for RCC M-25 Beams, cantilevers, bressummers, lintels & lintel bends over 1.5m span complete all as specified and directed.

M&L for RCC M25 Slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies, deck slabs and in shelves complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia cut to length, bent to shape required in stirrups, spacers and binders,with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F for Anodised aluminium frame for doors, windows, ventilators & Partition wall with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

S&F for 6mm Sheet glass, ordinary quality and glazing fixed with aluminium glazing clip and ruber gasket in square exc 0.5 Sqm in each pane and fixed complete all as specified and directed.

S&F for Aluminium anodised,barrel tower bolts Length of bolt 200 mm of ex?truded section and fixedcomplete all as specified and directed.

S&F for Butt hinges Size of hinges 100 mm, heavyweight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F for double action spring hinges(150 mm), brass, with phosphor bronze wirespring, bright polished complete all as specified and directed.

S&F for Aluminium 4 lever Mortice lock, vertical type, size 100 mm fixed complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick 20 over mm thick in cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Granite (of any type) 18-20mm work (table rubbed and polished in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished floor tiles as in vertical surface area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles laid over and including 10mm thick cement screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed.

S&F for Anodised aluminium snap grid frame size of grid 605 x 605mm work for false ceiling complete all as specified and directed.

S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including butterfly holding clip etc complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed.

M&L for two coat of sythetic enamal paint over one coat of red oxide primer on structural steel on new surfaces complete all as specified and directed.

Supply and installation of under ground grease seperator of size 1300 mm x 1490 mm having total volume 1250 Ltrs for 300 meals per day, sludge trap volume 400Ltrs, seperator volume 850 Ltrs,grease volume 160 Ltrs complete all as specified and directed. Make - Window Techs model No- Greasly-B type NS-4 cat no - 101-0406.

Supply and installation of grease seperator made of stainless steel grade SS304 having capacity for 100 meals per day,rapid release smell lid, integrated sludge trap, for free standing installation infrost free locations, having inlet and outlet pipe of diameter varies from 50mm to 100mm complete all as specified and directed. Make - Window Techs.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation, etc and getting out in soft/loose soil complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F for 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for PVC (SWR) bends/coupler any radius for 110mm bore PVC pipe complete all as specified and directed.

S&F for PVC (SWR) bends/coupler any radius for 75mm bore of pipe complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for Cutting into existing manholes of internal dia of pipe 150mm for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and directed.

Excavation over areas exc 1.5m but not exc 3.0m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Removal of surplus soil n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well raming in layers, not exc 25cm thick complete all as specified and directed.

M&L for provision of PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete including demolition of existing concrete and removing the rubbish off complete all as specified and directed.

M&L for provision of PCC 1:1.5:3 type A1 (using 20mm graded stone aggregate) as in foundation filling, floor bed and mass concrete complete all as specified and directed.

Form work to sides of concrete foundation, footings, base of columns, raft and raft beems, sides and soffits if any of foundation and plinth beems and similar work, verticle or to batter of rough finished surfaces of concrete flat complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers, columns and stanchions of rough finished surfaces of concrete square rectangular or polygonal complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat surfaces complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) curved surfaces complete all as specified and directed.

M&L for reinforced cement concrete (RCC) M25 Design Mix as in footing, plinth beams and columns below GL etc complete all as specified and directed.

M&L for reinforced cement concrete ( RCC) M25 Design Mix as in column etc complete all as specified and directed.

M&L for reinforced cement concrete( RCC) M25 Design Mix as in slab supported on wall, beam and like complete all as specified and directed.

M&L for brick work with sub class 'B' bricks built in cement mortar 1:4 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cm 1:3 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks built in cement mortar 1:4 straight or curved on plan to any radius in half brick th with old size bricks complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:3 on brick/ concrete surface etc mixed with WPC, finished fair and even without using extra cement complete all as specified and directed.

M&L for Loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

S&F for 150 mm bore PVC (SWR) pipes single socketed ISI marked IS-13592, type 'B' in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

M&L for Plain cement Concrete (1:3:6) type C-2 bed to 150 mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in complete all as specified and directed.

M&L for plain cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in copings, benching, bed plates, surface channel, drain and like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work complete all as specified and directed.

M&L for Framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

M&L for point wiring with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor (FRLS) 1100 Volts grade cable (red colour cable to be used for phase connection and black colour cable to be used for neutral connection) including in stove enamelled steel conduit with all accessories including 1.5 sqmm copper multistrand conductor (FRLS) 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet for mounting of fittings like switch, socket and fan regulator with 3 mm thick hylum laminated sheet cover incl complete all as specified and as directed for the following:-

Light/ Fan/ Exhaust fan point controlled by one switch

All as per item No 65 here in before but 4.0Sqmm P.V.C insulated un sheathed cable with stranded copper conductor for 5 pin 6/16 Amp switch socket combination on independent board complete all as specified and directed.

S&F for Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as specified and directed.

S&F for Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed.

S&F for LED light fitting 1x18/20 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. Make Crompton Cat Part No EXTN-1LT8-16/20.

S&F for flame proof wall mounting fan 450mm sweep 230V 50Hz, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection made up of with SS 304 / SS 316 IDU Cabinet Construction, with 03 No of iron blade, 900RPM Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. Make : Sudhir Cat Part No WMF/140.

S&F for factory made sheet metal enclosure for DBs double door, SPN, 240 volt, 8 Way, IP-42 protection with bus bar, neutral link, earth link complete all as specified and directed.

S&F for 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 10 to 32 Amp current carrying capacity complete with connection testing complete all as specified and directed.

S&F for 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 32-40 Amp current carrying capacity complete with connection testing complete all as specified and directed.

M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through & including stove enamelled steel conduit complete all as specified and directed.

M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm as earth continuity conductor drawn through & including medium grade PVC conduit complete all as specified and directed.

S&F for air termination single pointed, aluminium rod 12mm dia and 300mm long fixed on galvanised iron pipes with copper/ aluminium/ GI strip for earth conductivity to ground complete all as specified and directed.

S&F for aluminium strip 25mm x 3mm with saddles/ insulators and fixing screws for roof/ down conductors/ earth lead including brazing and nut bolts jointing at all joints for building/ hangar (roof/down conductor)/ pipe/ trench complete all as specified and directed.

M&L for Test point terminal box of size 200 x 100 x 100 mm made out of 2 mm thick hot dip galvanised sheet drilled and screwed including 6 Nos 15 mm long hexagonal head screws complete with test point terminal block made out of Gun metal or Phosphorus Bronze size 75 x 75 x 25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal head screws, etc complete all as specified and directed.

Supply & install GI strip 25X4 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate 600mm x 600mm x6.30mm thick elecrode and 25mm x 4mm galvanised iron strip as earthing lead burried directly in ground vertically (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, the earth plate surrounded by adequate quantity of charcoal dust and common salt to a packed thickness of 15 cm on all sides connected to GI strip 32mm x 6mm as earth lead by means of bolts, nuts, check nuts and washers (including welding) of galvanised iron or steel and connected to main switch board / panel/ test point at the other including necessary earth work in any type of soil, returning filling in and removal of surplus soil, concrete pit in PCC (1:3:6) type C1, pre cast RCC 1:2:4 type BI cover slab 54cm x 54cm x 5cm reinforce with 8mm dia bar TMT @150mm centre to centre both ways with one handle for lifting made out 8mm dia MS bar with wire mesh funnel, 20mm GI tubing medium grade for watering and 40mm GI tubing light grade for protection, test point, testing on completion all as shown in Electrical Plate No 3 of SSR Part-I complete all as specified and directed.

M/S CHAKRA GOHAIN (BID ID -3398579)

M/S D G ENTERPRISE (BID ID -3398890)