85968 PROVN OF STANDBY DG SET WITH ALLIED WORK FOR NEW CCL AND MAIN PUMP HOUSE AT AICTS AND SPECIAL REPAIR / RENEWAL OF 250 KVA DG SET IN PLACE OF BER 125 KV DG SET INCLUDING OTHER CONNECTED ACCESSORIES AT ALC OT UNDER AGE E/M-I OF GE (SOUTH) PUNE

Supplying, installing, testing and commissioning, factory assembled silent Diesel Engine driven generator set, fully wired alternator AC, to give an out put of 250 kVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hz ± 1% supply, 1500 RPM, CPCB IV+ regulation, directly coupled with diesel engine liquid cooled turbo charged after cooled mounted on common base frame complete with floor mounting fuel tank (with fuel line & accessories, vibration damper pads, microprocessor based genset monitioring controller Engine Safeties & Protections Battery With Leads , including termination and connection of cable with gland and lugs and comprising of following :- LOCATION : (a) NEW CARDIAC CATHERISATION LAB (CCL) AT AICTS PUNE - 01 No. (b) OT, ALC PUNE - 01 No.

(A) Diesel Engine : Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500 RPM 4 stroke, under NTP conditions of BS 5514 and conforming to IS 10002, DIN 6271 & ISO 3046 with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories, Diesel engine of rated speed at full load electric start developing with system with radiator and including electronic governor control of classG-3, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries of adequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/ flexible coupling and coupling guard complete. (a) Radiator with blower fan or heat exchanger with guard. (b) Pipe coupling for engine cooling system piping. (c ) Corrosion inhibitor coolant (d) Paper element filters (i) Fuel filter (ii) Lube oil filter (iii) By pass (e) Fly wheel housing and fly wheel to suit alternator. (f) Engine bearing mechanism in fly wheel housing. (g) Shut off coil with safety for LLOP/HWT/over speed. (h) Dry type air cleaners and vacuum indicators. (j) Residential silencers. (k) Stainless steel exhaust flexible bellows. (l) BLANK. (m) Battery charging alternator.

(B) Electronic instrument panel, complete with all accessories as per manufacturer's specifications displaying the following:- (i) Battery. -as per manuactrure specified. (ii) Water temperature. (iii) Lubricating oil pressure. (iv) Engine speed -1500 Rpm (v) Engine hours (vi) Frequency. (vii) Voltage. (w) Safety control (Trip and indication). (i) High water temperature (ii) Low lube oil temperature (iii) Overspeed stop (C) Base frame : Sturdy, fabricated welded construction, channel iron base frame (duly painted) for mounting engine and alternator as per manufacturer's design alonwith AVM pads. (D) Battery : as per manufacturer specified with leads & terminals. (E) Alternator : Suitable rated 250 kVA, 0.8 PF, 415 Volts, 3 Phase, 4 Wire, 50 Hz at 1500 RPM, self excited and self regulated with AVR brushles, screen protected, drip proof, insulation class-H, IP -23, voltage regulation grade - VG 3 self ventilated and conforming to BS : 5000 / IS : 4722 suitable for engine as mentioned here-in before, conformig to IS: 13364 (Part-1) (F) Acoustic Enclosure : Specially design for CPCB norms M&L for acoustic enclosure for the above 250 kVA DG set to reduce noise level to 75 dB measured at 1.0 meter distance for audiable frequencies as per guide of Central Pollution Control Board and manufacturer's specification and comprising of following from authorised GOEMs of Gen Set manufacturer's specified .

Supply and installation, testing of AMF panel outdoor type suitable for AMF 250 kva with factory made type panel weather proof, vermin proof, fully ventilated both side opening and fabricated out of 3.00 mm thick crca sheet & mounting channel 75 mm having bus bar of aluminum 600 Amps capacity, three phase and one neutral fixed on insulator and bus bar insulated by colored heat shrinkable sleeve & housed in specified compartment both side open able. Including powder coating internally externally the entire steel surfaces. All the cover shall have with suitable locking arrangements, fully internally wired with suitable size of thimbles. Incoming/outgoing internal connection with pvc insulated pvc sheathed multi stranded copper wire of suitable size all as directed The panel shall be provided with 04 Nos 50mm x 50mm x 6mm thick angle iron suppons of not less than each 0.6 mtr height duly painted with anti cormsive black paint and grouted on floor/well atc and suitable fixing amanament as per she requirement connection to the existing earthing., including PCC 1:3:6 & comprising of following :- LOCATION : (a) NEW CARDIAC CATHERISATION LAB (CCL) AT AICTS PUNE - 01 No. (b) OT, ALC PUNE - 01 No.

Under voltage relay 415v AC for main - 1 No Under voltage relay 415 v AC for DG - 1 No AC timer 230 volt, 2 NO. +2 NC - 1 No DC timer 24 Volt - 1 No Control mcb sp 16 A - As required Control mcb sp 6 A - As required Automatic battery charger 24 volts- 1 No Led indicating light for main & DG - 6 Nos. Led indicating light for main & Gen. On - 2 Nos. Led indicating light for battery charger - 1 No. VAF Meter - 2 Nos AMF Controler 3 Phase 4 wire -1 No Volt meter selector switch - 1 No. Amp meter selector switch - 1 No. 500/5 Amp - 3 Nos. DC volt meter 15/30 V - 1 No. DC amp meter 0-15 A - 1 No. Trickle / boost switch - 1 No. Auto / manual switch - 1 No. Push button start & stop with elements - 2 Nos Power contactor 400 Amp 3 pole 415V for DG - 1 No Power contactor 400 Amp 3 pole 415V for main - 1 No MCCB 400 Amp 35 ka 3 pole for main & dg supply - 2 Nos Control relay -1 set Over load relay 2.5-4 A - 1 No. Bus bar 600 A, 3 strips & n/l 300 A . Aluminium - 1 set

Supplying, installing, testing and commissioning, factory assembled silent Diesel Engine driven generator set, fully wired alternator AC, to give an out put of 160 kVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hz ± 1% supply, 1500 RPM,CPCB IV+ regulation, directly coupled with diesel engine liquid cooled mounted on common base frame complete with floor mounting fuel tank (service tank) of minimum capacity 385 ltrs with fuel line & accessories, vibration damper pads, Standard Control Panel With Controller PS0602, Engine Safeties & Protections Battery With Leads With dept tank capacity 60 Ltrs, including termination of cable with gland and lugs and comprising of following :-

(A) Diesel Engine : Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500 RPM 4 stroke, 6 cylinderunder NTP conditions of BS 5514 and conforming to IS 10002, DIN 6271 & ISO 3046 with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories, Diesel engine of rated speed at full load electric start developing with system with radiator and including electronic governor control of class A1, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries of adequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/ flexible coupling and coupling guard complete. (a) Radiator with blower fan or heat exchanger with guard. (b) Pipe coupling for engine cooling system piping. (c) Corrosion inhibitor coolant (d) Paper element filters (i) Fuel filter (ii) Lube oil filter (iii) By pass (e) Fly wheel housing and fly wheel to suit alternator. (f) Engine bearing mechanism in fly wheel housing. (g) Shut off coil with safety for LLOP/HWT/over speed. (h) Dry type air cleaners and vacuum indicators. (j) Residential silencers. (k) Stainless steel exhaust flexible bellows. (l) BLANK. (m) Battery charging alternator.

(B) Electronic instrument panel, complete with all accessories as per manufacturer's specifications displaying the following:- (i) Battery as per manufacturer specified. (ii) Water temperature. (iii) Lubricating oil pressure. (iv) Engine speed -1500 Rpm (v) Engine hours (vi) Frequency. (vii) Voltage. (w) Safety control (Trip and indication). (i) High water temperature (ii) Low lube oil temperature (iii) Overspeed stop (C) Base frame : Sturdy, fabricated welded construction, channel iron base frame (duly painted) for mounting engine and alternator as per manufacturer's design alonwith AVM pads. (D) Battery : as per manufacturer specified with leads & terminals.

(E) Alternator : Suitable rated 160 kVA, 0.8 PF, 415 Volts, 3 Phase, 4 Wire, 50 Hz at 1500 RPM, self excited and self regulated with AVR brushles, screen protected, drip proof, insulation class-H, IP -23, voltage regulation grade - VG 3 self ventilated and conforming to BS : 5000 / IS : 4722 suitable for engine as mentioned here-in before, conformig to IS: 13364 (Part-1) (F) Acoustic Enclosure : M&L for acoustic enclosure for the above 160 kVA DG set to reduce noise level to 75 dB measured at 1.0 meter distance for audiable frequencies as per guide of Central Pollution Control Board and manufacturer's specification and comprising of following from authorised GOEMs of Gen Set manufacturer's specified.

Supplying, installing, testing and commissioning imdoor CPRI approved AMF Control panel of capcity 160 KVA factory fabricated cubical type, free standing, floor mounted, outdoor type, IP-52, with rotary handle, provided with removable rear panels & hinged front panel for easy accessibility, fabricated out of not less than 2.0 mm thick CRCA sheet with partition and switch enclosure door 1.6 mm including two coats of powder coated paint over a coat of red oxide primer with MS angle stand of size 50x50x6mm and shall be mounted on including necessary grouting in PCC 1:3:6 type C-1 by using 20 mm graded stone aggregate completed with legs 30 cm in ground in PCC and 40 cm above ground and termination of cable with gland and lugs comprising of following :- LOCATION : MAINT PUMP HOUSE AT AICTS PUNE - 01 No.