GE/SRA/T-42/2025-26

Amount

SCHEDULE 'A' PART-I (BUILDING WORKS)

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

M&L for Hardcore of broken stone or boulder of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for Cement concrete, 100mm thick, type D- 2, 1:4:8 (40mm graded aggregate) in sub floors, sub bases, pavings etc., complete all as specified and as directed.

M&L for providing and laying 30 mm thick Anti-Static Bitumastic flooring conforming to IS 8374, mix duly prepared in mastic cooker and spread complete all as specified and directed.

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Paving, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

Excavating in trenches, in soft/loose soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm complete all as specified and as directed.

Removing excavated material/soil from site and disposing off to outside AF land complete all as specified and directed.

M&L cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in filling and mass concrete complete all as specified and directed.

M&L for RCC 1:2:4 type B1, using 20mm grade aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed

M&L for brickwork with fly-ash bricks (with old size bricks), straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on other than fair faces of Brick Walls, Surfaces finished Even and Smooth without using Extra Cement complete all as specified and as directed.

M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on fair faces of brick walls or concrete surfaces finished even and fair (up to any height) for external surfaces complete all as specified and directed. (Note : Water Proofing compound shall be measured & paid separately as "Supply only")

Supply only Liquid Water Proofing Compound, conforming to IS code or as approved, complete all as specified.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end & screwed the other or screwed both ends each screwed end to be fitted with washers & one hexagonal or square nut, exc 22.5cm but n exc 30 cm long, diameter 16 to 20 mm complete all as specified and directed.

M&L for Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment Gde Fe 410W complete all as specified and directed.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 or RHS/SHS Sections conforming to IS 4923:1997 grade YST 210 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. No extra measurement for the same will be considered except for base plates at top & bottom of columns)

M&L for preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 1.24 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter or cladding in roof.

S&F factory made single extruded WPC (Wood Polymer composite) solid door/window/ceosetory windows & other frames/chowkhat of size 45 X 75mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 grams) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N(Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with mild steel hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (NOTE: MS hold fast/lugs or SS dash fasteners shall be paid for seperately. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made)

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and shall be fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: Butt hinges shall be paid separately)

S&F Butt hinges, 100 mm long, stainless steel complete all as specified and directed.

S&F Aluminium alloy Handle 125mm long, cast type, anodised, complete all as specified and directed.

S&F Aluminium Barrel Tower Bolt 150mm long (weight not less than 130 Gram), extruded section, complete all as specified and directed.

M&L for aluminium partition consisting of anodized aluminium sections of 14 gauge thickness with bottom rail of size 114.30mm x 38.10mm and top, centre and vertical rails of size 63.50mm x 38.10mm including fixing glass panel or boards with rubber gaskets (as approved) and alumnium beading 20x3mm size, duly fixed in position complete all as specified and directed. NOTES:- 1) Sheet glass and PVC board shall be measured and paid seperately as "Supply Only". 2) Contractor shall ascertain the required/planned dimensions of partition before quoting his bid. No claim shall be entertained at a later stage.

Supply only 12 mm thick pre-laminated particle boards, interior grade, laminated both sides with decorative choice laminations, cut to size and fixed with screws to aluminium partions, doors etc complete all as specified and directed.

S&F anodised aluminium frame for door, windows and ventilators with one or more rebates including joining cleat for fixing glass, boarding etc. complete all as specified and directed.

S&F anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber packing handle 2 Nos in each door, hinges, Mortise lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc as per manufactures instruction complete all as specified and directed. (NOTE:- Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle, Mortice Lock etc as described in item. Sheet glass shall be measured seperately)

S&F Sheet Glass 5.50 mm thick, plain (as approved by GE), fixed to Aluminium doors of size exc 0.50 sqm each pane complete all as specified and directed.

S&F Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium alloy Sheet Foundation Box, Main Body with Stainless Steel Cover, Governing Pivot made of Brass, Other Parts made of Mild Steel heavy duty complete all as specified and as directed.

M&L for complete removal of existing treatment on old painted surfaces of walls by scrapping and removing layers of all wall finishes including cleaning, watering to make the surface clean and free from dust, etc including necessary scaffolding, safety and protective measures complete all as specified and directed.

M&L for preparing New/Undecorated Plastered Surfaces of Walls, applying a coat of suitable cement primer followed by a Coat of 2.0 mm thick Wall Putty (in two layers of 1mm thick) including rubbing down with Sand Paper to obtain a smooth finish surface and finishing with Two Coats of Acrylic Distemper (as approved) as per desired shade/tint complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and finished with two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade over a coat of suitable exterior primer, applied to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, up to 4 storey height incl necessary scaffolding, safety gear, etc complete all as specified and directed.

S&F Chlorinated Polyethylene Chloride (CPVC) pipes 20 mm outside dia, SDR-11, having thermal stability for hot and cold water supply including all SDR-11 CPVC plain and brass threaded fittings (such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector etc) fixed / laying walls, ceilings or in floors etc. with suitable size MS clamp of spacing 1.00 mtr etc pipe line complete all as specified and directed. (NOTE: Quoted rate shall deemed to included for cutting chases in brickwork for concealing pipes)

S&F CPVC Ball valve 20mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white, with 'P' or 'S' trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC flush Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in cement mortar 1:3, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed.

S&F chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed.

S&F Vitreous China, white, half stall urinal flat back with grating and union for discharge pipe (excluding flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (NOTE: Quoted rate shall be deemed to include for the cost of waste coupling and waste pipe)

S&F Self closing angle cock pressmatic for urinal with wall flange and 200 mm connecting pipe duly connected with and including brass chromium plated Urinal spreader complete all as specified and directed.

S&F Vitreous China Wash Hand Basin 450x300mm in size, White (Flat Back or Angle Back Type), provided with 32mm dia Brass Chromium Plated Waste Fitting, PVC waste pipe, brackets incl making good disturbed Surfaces in Cement Mortar 1:3 and filling joints with whte cement complete all as specified and directed. (NOTE: Cost of CP wate coupling and PVC waste pipe is deemed to be included in the quoted rates)

S&F Chromium plated brass Pillar tap, with aerator, minimum weight 650 grams, fixed to WHB complete all as specified and directed.

S&F Brass Chromium Plated Tubular Towel Rail, 60 Cm long with Brackets, total weight not less than 300 grams complete all as specified and directed.

S&F stainless steel Grating Round 100mm Dia with waste hole jointing with Solvent Cement complete all as specified and directed.

S&F PVC Floor Trap 75mm bore (dia) with Grating including jointing to Waste Pipe fixed in Cement Concrete 1:2:4 (20mm graded stone aggregate), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid on floor, trenches etc complete all as specified and directed.

S&F PVC (SWR) 75mm bore (dia), Bend any type and jointing with Solvent Cement complete all as specified and directed.

S&F PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Short Body with Capstan Head, minimum weight 400 grams, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed.

S&F angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, minimum weight 300 grams, with wall flange fixed to iron pipe complete all as specified and directed.

S&F Chromium plated brass two way Angle valve, fancy type, minimum weight 350 grams, with wall flange fixed to 15 mm bore Iron pipe, complete all as specified and directed.

M&L for providing Machine cut Pre-Polished Kota Stone Tiles, 18-20mm thick in Flooring, laid over including 20mm thick screed base of cement mortar 1:6 and joined with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall be deemed to be included in the quoted rate.

M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square / rectangular), area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for Coloured Glazed Ceramic Tiles in vertical surface 450mm X 350mm X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 10mm thick rendering as Screed or backing coat of wall tile in Cement Mortar 1:3, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for providing Vitrified Ceramic Tiles, Double Charged, 9-10mm thick (Square/ Rectangular), coloured, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

-ditto- but for vitrified tiles in skirting, fixed over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 type B0 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles in Floor, complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C2 (40mm Graded Stone Aggregate), 75mm thick, as in plinth protection finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS)

M&L concealed Point Wiring with 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable with 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn through and including Rigid Non-metallic PVC Conduit 19/20 mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and Making Good in Cement Mortar 1:3, providing Sunk GI Terminal Box (1.2mm thick) of suitable size (as required) for mounting MODULAR TYPE Switches, Sockets, Fan Regulators, Sockets, etc with Earth Continuity Wire connected to Common Earth dolly complete all as specified and as directed for the folowing:- (NOTES :- (i) Where tube light fitting is to be fitted/ suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Quoted rate shall be deemed to be inclusive of the cost of terminal box. Modular cover plate & frame shall be measured and paid seperately (iii) Cost of cutting chases for concealed wiring and making good surfaces with cement plaster and putty shall be deemed to be inclusive in the quoted rates. No claim shall be admissible at a later stage)

for one MODULAR TYPE light / bell / ceiling fan / exhaust fan point controlled by one way switch with 1.50 Sq. mm wire for mains & neutral

for one MODULAR TYPE 5/6 Amps Pin Socket Outlet on the same board, with 1.50 Sq. mm wire for mains & neutral

for one MODULAR TYPE 5/6 Amps socket outlet on independent board, with 1.50 Sq. mm wire for mains & neutral

for one MODULAR TYPE 15-20 Amps socket outlet on independent board, with 2.50 Sq. mm wire for mains & neutral

M&L for concealed type point wiring with 2.50 Sq. mm (nominal area) FRLSH grade PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including steel conduit (not less than 20 mm dia) complete with all fittings and accessories, fixed to walls/ceiling and including 2.50 Sq. mm (nominal area) FRLSH grade PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for one flame proof light/fan point controlled by one flame proof rotary switch complete all as specified and directed . NOTE:- Cost of cutting chases for concealed wiring and making good surfaces with cement plaster and putty shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

S&F Switch, Flame Proof Rotary type with Termination Box in LM6, 16 Amp, Single Pole, 250 Volt , complete all as specified and as directed.

S&F Modular Switch 1 way 6 A, 1 module complete all as specified and as directed.

S&F Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and as directed.

S&F Modular Switch 1 way 16 A, 1 module complete all as specified and as directed.

S&F Modular Socket 6 & 16 A, 2/3 pin combined 2 module complete all as specified and as directed.

S&F Ceiling rose, surface type, three terminals complete all as specified and directed

S&F exhaust fan 300 mm sweep, copper motor, 1300 RPM, heavy duty, AC Single Phase 230/240 volts, metal body, with louvers complete with all accessories and connecting up with and including twin core twisted flexible copper conductor cable of size 1.5 sqmm (nominal area) from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model: Ventil Air DS / CROMPTON, Model: Transair / USHA, Model: Aero Clean Plus or equivalent model in BAJAJ / ALMONARD / ORIENT) (NOTE : Hole shall be left in brickwork during construction stage and shall be finished properly with cement plaster.

-ditto- but for exhaust fan 380 mm sweep, copper motor, 1400 RPM, heavy duty, AC Single Phase 230/240 volts, metal body with louvers complete (MAKE : HAVELLS, Model: Turbo Force / CROMPTON, Model: EXHD380-6-1 / USHA, Model: Turbo Heavy Duty or equivalent model in BAJAJ / ALMONARD / ORIENT)

S&F wall mounted fan having copper motor with PVC blades, 400 mm sweep, 230 volts single phase, silent operation, min 1330 RPM, quick start with high torque, speed regulation with double pull cord for convenience complete all as specified and directed.

-ditto- but 450 mm sweep wall fan

S&F flameproof exhaust fan, 300mm size, with and including louvers including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surface including connecting up with three core flexible copper conductor FRLS cable of size 1.5 sqmm (nominal area) complete all as specified and directed.

S&F surface mounted LED luminaire, 1 X 20 Watt in aluminium housing, 100 lumen/watt, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed.

S&F surface mounted spot light, with pressure die cast aluminium heat sink, with COB LED, 07-09 Watt, 5700-6000K, operating voltage 180-270V, with constant current electronic driver complete with all accessories and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed. (MAKE: HALONIX, MODEL: RIGEL PRO / GOLD MEDAL, Model: BIBO or similar models in other makes listed in tender)

S&F LED Flood Light fitting, of various capacity as mentioned under, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver and toughened glass cover, IP66 grade ingress protection, impact resistance IK07 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power factor not less than 0.90 (g) colour temperature 5700-6000 degree K

70 Watt Flood Light Luminaire

35/36 Watt Flood Light Luminaire

S&F Metallic Distribution Board, Double Door, SPN, IP 43 protection, 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. NOTE: Incoming and outgoing MCBs shall be measured and paid seperately.

S&F Metallic Distribution Board, Double Door, SPN, IP 43 protection, 240 volts, 6 way, with 100 Amps copper Bus Bar complete all as specified and directed. NOTE: Incoming and outgoing MCBs shall be measured and paid seperately.

S&F MCB, 'B' Curve, SPN, 40-63 Amps, breaking capacity 10KA complete all as specified and directed.

S&F MCB, 'B' Curve, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

S&F laying Galvanised Steel Tubing Pipe 50mm bore (dia), light grade with Bend, laid in Trenches or under Roads/ Flooring/ Culverts and/or fixing to Electric Poles or walls with suitable size Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc., complete all as specified and as directed.

S&F PVC electrical conduit, 25 mm dia, MMS type, medium grade incl all fittings and accessories complete all as specified and directed.

M&L for concealed sub main wiring with 2 run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through and including PVC conduit (medium grade) of suitable size, including taking down of old Submain wiring any type including batten/ conduit/casing at any indicated situation complete all as specified and directed. NOTE : (1) Three runs of single core 6.0 sqmm cable & one run of PVC conduit shall be measured as one unit. (2) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage. (3) On completion of the wiring work, the contractor shall fill and finish the chases with cement mortar 1:6 and finsihed flush with the adjacent surfaces. Rate quoted by the contractor shall be deemed to include for the above aspect and no claim shall be entertained at a later stage.

S&F Air Termination Single Pointed Copper Rod 12mm dia and 300mm long with suitable Arrester Clamp made out of Brass/Gun Metal including provision of Cement Concrete 1:2:4 (20mm graded stone aggregate) Block 300x300x300mm, complete all as specified and directed.

S&F Aluminum Iron Strip 25x3mm with Saddles and fixing Screws for Roof/Earth Conductors and Down Conductors, complete all as specified and as directed. NOTE: Cost of Screws, Saddles, Insulators, Nuts and Bolts, etc. shall be deemed to be included in Quoted Rate.

S&F Test Point Terminal Block made of Gun Metal or Phosphorus Bronze size 75x75x25mm, drilled and screwed including 3 No. 8mm dia, 25mm long hexagonal Head Screw, complete all as per specified and as directed.

S&F Galvanised Iron Tubing/Pipe 40mm bore (dia), light grade for Strip Protection, fixed in Walls/Floors with suitable type of Clamps, etc., complete all as specified and as directed.

M&L for Providing, cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in blocks etc for fixing bases of air termination rods, GI pipes etc, surfaces finished even & smooth without using extra cement complete all as specified & directed.

Supply, installation, testing and commissioning of "Silent Type" Diesel Generating Set, complying with CPCB IV+ norms along with having prime continuous rating of 10 KVA, 415 Volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system and consisting of followings :-

(A) Diesel Engine :- Diesel Engine, 4 stroke, naturally aspirated, water cooled (with coolant), electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 45 Degree C, RH & height above MSL as applicable for Sirsa and conforming to ISO 8528-1, capable of taking 10% overloading for one hour after 12 hours of continuous operation. The engine will be fitted with all the required accessories.

(B) Engine Mounted Instrument Panel fitted with and having digital display for following :- (i) Start-stop switch with key (ii) Water temperature indication (iii) Lubrication oil pressure indication (iv) Lubrication oil temperature indication (v) Battery charging indication (vi) RPM indication (vii) Over speed indication (viii) Low Lub Oil trip indication (ix) Engine Hours indication

(C) Alternator :- Synchronous alternator rated as 10 KVA, 415 Volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 45 Degree C, RH & height above MSL as applicable for Sirsa. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS: 4722/BS 2613 suitable for tropical conditions and with Class 'H' insulation.

(D) Base Frame & PCC Foundation :- Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer.

(E) Fuel Tank :- Daily service fuel tank, fabricated out of MS CRCA sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS Class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

(F) Exhaust System :- Dry exhaust manifold with exhaust silencer and catalytic convertor

(G) Starting System :- 12V/24V DC starting system comprising of starter motors, voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (25 plates, 180 Amp Hour capacity lead acid type) as required as per specifications.

(H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per specifications.

NOTES :- The quoted rate for DG Set shall be deemed to be inclusive of the following :- (i) PCC foundation for installation of DG Set. (ii) Spare Parts to be provided with the DG Set as specified in particular specifications. (iii) First filling of engine oil required for testing & commissioning of the DG Set. (iv) All requisite test certificates, manuals, manufacturer's warranty etc shall be submitted to Engineer-in-Charge for records. (v) The DG Set shall be tested at site for 12 hours in the presence of IEM/Rep of Accepting Officer and Engineer-in-Charge and test results shall be recorded and signed by both parties. . (v) Diesel required for testing of DG Set at site shall be issued by Deptt as "free for use". However, if the DG Set fails in these tests, further diesel will not be issued for the subsequent tests and the contractor shall procure the same under his own arrangements.

Supply, laying, jointing and testing, fixing to wall using clamps/ pole / floor or in air or passing through pipes / ducts / road / path / drain, laid in trenches, 1100 volts grade heavy duty electric cable XLPE insulated, screened, PVC bedded, galvanised steel wire or wire armoured with electric power cable 1100 volts grade with stranded aluminium conductor of size 3.5 core 50 sqmm confirming to IS-7098 Part-1 and its latest amendments complete all as specified and as directed. NOTE: Earthwork, sand cushioning & brick protection shall be measured and paid seperately.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, punned thickness of Sand Cushioning only will be Measured.

Supply & laying in Trenches Sub-class ‘B’ Bricks, kiln burnt, laid perpendicular to the cable for Cable Protection, complete all as specified and as directed.

S&F laying Galvanised Steel Tubing Pipe 20mm bore (dia), medium grade, with all fittings, fixed complete to walls and ceilings or laid in floors with suitable size Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc., complete all as specified and as directed.

S&F Gun Metal Gate valves as per requirement of the site, for 20mm bore pipe complete all as specified and as directed.

ITEM NO 2.50 (CONTD...) C) OUTGOING : (i) MCCB 63 Amp 4 pole, 25 KA, with fixed magnetic & adjustable thermal release, adjustable overload 80-100% - 01 No (ii) On Load Change Over Switch, 63 Amps, 4 Pole, Manual Type, Open Execution, 415 Volts 3 Phase - 01 No NOTES: (i) Contractor shall submit IP Test Report and verification of short circuit withstand test report issued by CPRI in respect of Panel Fabricator. (ii) Bus bar should be above the MCCB horizontal type. Spacing of bus bar should be sufficient for cable connection upto 120 sqmm. (iii) Contractor shall submit drawing for approval of Accepting Officer prior to placing order. (iii) Make of accessories shall be as specified in tender. (iv) Cost of PCC foundation shall be deemed to be inclusive in quoted rate.

M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth strip 25 x 4 mm (up to 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

M/s Shree Bala Ji Construction Company (BID ID -3419121)

shiv shanker enterprises (BID ID -3418314)