Development of various parks in Owala Majiwada Constituency within Thane Municipal Corporation limits

Amount

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete.

Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking or spreading as directed, dewaterin, preparing the bed for the foundation and necessary back filling, ramming, watering, including shoring and strutting as necessary complete. ( Spec.No. : Bd.A.1Page no 259/ CSR Page No.150

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming ,watering including shoring and strutting etc. complete. (Lift from 1.5m To 3.0 m.) By Mechanical Means

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing preconstructional antitermite treatment as per I.S.6313(Part-II) treatment by treating the back fill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrif as per One Square Metre of vertical surface area covering 10 years guarantee on bond paper.

Providing pre constructional antitermite treatment as per I.S.6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at1.0 percent of clorophyrif as per One Square Metre of surface area covering ten years guarantee on bond paper.

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layersincluding watering and compacting etc. complete.

Providing soling using 80 mm size granite / quartzite / gneiss / trap metal in 15 cm. layer including hand packing filling voids with sand / grit, ramming, watering complete. (Spec. No. : As directed by Engineer-in-charge /Page No. 154)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite / quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement with max 20% fly Ash ( Fly-ash upto 20% by weight of Cement) over a prepared sub base with 43 grade cement , coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a Tilting type Concrete Mixer as per approved mix design, admixtures, spreading, laying compacting and finished in a continuous operation without paver machine, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and laying in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying /pumping cover blocks,compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap /granite /quartzite /gneiss metal for R.C.C. beams and as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying /pumping, compaction and roughening the surface if special finishish to be provided and curing etc. complete. (Excluding reinforcement and structural steel). withfully automatic microprocessor based PLC with SCADA enable dreversible Drum Type mixer /concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, form work, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mixcement concrete M-30of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position HCRM /CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules .including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing cement based water proofing treatment to terraces (Indian water proofing oralike) with brick batslaid inrequireds lopetod rainthe water foranys panafter cleaning the base surface. Applying acoa to fcements lurrya dmixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 ad mixed with approved water proofing compound filling up to half dep tho fbrickbats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M. 1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of samem or tarad ded with jute fiberat 1 Kilogram per bag including finishing the surfaces mooth with cements lurryad mixed with approved water proofing compound. Marking finished surface with falses quares of 300 mm x 300 mm.making the junctions at the parapet rounded and tape red top for required height,with dripmould at the junction of plaster and parapet and curing and covering 10 years Guarante eagainst leak proofnes son Court fees tamp paper of Rs.500/-including ponding test etc. complete.

Providing and applying a base coat comprising of 1Kilogram Polydee-MC and 1 Kilogram fresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component (mixing ratio 2A:1B)) Anti bacterial food grade coating inside drinking water tankin two coats with time interval of minimum 8 hrs.covering 7 years guaran tee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stone in cement mortar 1:3 in basement with patent water proofing compound added to it at rate of 1Kilogramper bag of cement including bailing out water manually, scaffolding racking out joints when plastering is to be done and watering etc. complete.

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc.Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including strikingjoints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing internal cement plaster 12mm. Thick in Single coats in cement mortar 1:3 with out neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 6mm thick in a single coat in cement mortar 1:3 with out neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing and applying plaster with plaster of paris in 6 mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.

Providing and applying Royal Luxury Emulsion of approved make on internal wall surface as detailed be low Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10% or waterby 15 to 20% allowing to dry for 6 to 8 hours After applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity.Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 % or 65 to 70% by role Applying paints Royal eluxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram / 15l). plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned company technologist.

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to10 mm thicknes sand confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to10mm thickness and confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning,washingand finishing etc. complete.

Providing and supplying of Wood Plastic Composite (WPC) flooring made from 70% of polymer, 15% wood powder and rest 15% of additives and requisite chemicals with installation and hardware.

Bamboowood 10mm thick Wall Cladding including Threshold & T-mold - Providing & fixing in position Phenol bonded Bamboo wood wall cladding at all height with planks of sizes 10mm thick, 1900mm length (minimum) and 135mm wide approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building materials & Technology Promotion Council (BMTPC). with necessary profiled edges fixed with BR nails to frame work made of second class teak wood of size 50 x 50mm in centre and ends of each tile. The bamboowood cladding shall be laid over teak wood frame and hold in place by 50mm thick teak wood placed in centre of two teak wood and backlayment and covered with 1.00mm thick expanded poly ethylene foam of density 25Kilogram/cum in two layers first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The Bamboowood planks shall have minimum density of 1000 Kilogram/cum & minimum Hardness 1000 Kilogramf. with Eco friendly UV coating, all complete as per direction of Engineer in-charge.

Providing and preparing kitchen otta up to 75 cm width, made up from 30 mm thick and 75 cm high vertical support for kadppa at 1 m. c/c of 25 mm thick both side polished kadappa middle shelf and bottom of 20 mm thick one side polished kadappa with facia patti of 20 x 50 mm kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning etc. complete.

Providing and fixing Basket ball court flooring

Kid’s Play Area- Rubber flooring Providing and Applying Ethylene-propylene diene monomer (EPDM) is a durable and versatile M-class synthetic rubber poured in place on-site, providing a seamless surface of 8-10 mm thickness.

Providing and fitting batminton nylon net size 6m x 1m on existing MS poles.

Providing and fitting metal basket ball ring with nylon net - Diameter - 46 cm. finish in powder coating, paint

Rytmisk - 11 Indian Notes-The Stand is made up of Stainless Steel Pipe 88 OD of 304 Grade. Black aluminium resonators are Anodized and Aluminium TUNED notes are also Anodized. Fitted with SHEET as per arrangement of notes with SS Nut Bolts & SS Washers with Anti Theft Nylon Lock Nut Bolts. Two Nos Beaters Provided which are attached with wire. Instrument is Mounted on SS Plate with Nylon Lock Nut Bolts. SS Frame Shall be Buffed for Mirror Finish. Caps are fitted to Resonators so no sharp edges are exposed

Dual Rytmisk - 22 Western Notes-The Stand is made up of Stainless Steel Pipe 88 OD of 304 Grade. Black aluminium resonators are Anodized and Aluminium TUNED notes are also Anodized. Fitted with SHEET as per arrangement of notes with SS Nut Bolts & SS Washers with Anti Theft Nylon Lock Nut Bolts. Two Nos Beaters Provided which are attached with wire. Instrument is Mounted on SS Plate with Nylon Lock Nut Bolts. SS Frame Shall be Buffed for Mirror Finish. Caps are fitted to Resonators so no sharp edges are exposed

Rumba Drums - 2 The Stand Shall is made up of Stainless Steel Pipe 88mm OD of 304 Grade. Drums with Special Caps are fixed with Bush. These are Fitted on SS Nut Bolts & SS Washers with Nylon Lock Nut Bolts on the main pipe. SS stand Shall be Buffed for Mirror Finish.

Carillon - 11 Indian Notes -The Stand is made up of Stainless Steel Pipe 88 OD of 304 Grade. Anodised Aluminium TUNED notes are fixed to SS 304 Grade Clamps. These are Fitted on STRIP as per arrangement of notes with SS Nut Bolts & SS Washers with Nylon Lock Nut Bolts. Two Nos Beaters Provided which are attached with wire. Instrument is Mounted Nylon Lock Nut Bolts. SS Frame Shall be Buffed for Mirror Finish. Finishing of Notes is very important so no sharp edges are exposed.

Lyra Gong - The Stand is made up of Stainless Steel Pipe 88mm OD of 304 Grade. The Curved Frame is made of SS Pipe 38mm OD of 304 Grade. The Stainless Steel Bells Grade 304 are fixed with SS Nut Bolt & SS Washer with Nylon Lock Nut Bolts on the main pipe. SS stand and Bells are Buffed for Mirror Finish. Two Nos Beaters Provided which are attached with wire.

Riders - Providing and fixing FRP (Fibreglass reinforced plastic) riders.

Providing and fixing Double Toddler Swing (PASW04) Equipment area - 1.8m x 0.97m Safe Play Area - 3.0m x 3.5m Ideal for age - 2-5yrs

Providing and fixing Multi-purpose Play System Equipment area - 13.0m x 8.4m Safe Play Area - 16.0m x 11.4m Ideal for age - 4-12yrs

Providing and fixing play area Combination Set made in metal and FRP

Providing and fixing Double Arch Swing (PASW05) Equipment area - 3.1m x 1.08m Safe Play Area - 4.3m x 5.0m Ideal for age - 5-10yrs

Providing and fixing FRP multi see-saw. (PASE03) Equipment area - 3.0m x 0.5m Safe Play Area - 4.5m x 1.5m Ideal for age - 4-12yrs

Providing and fixing Scrambler Set (PARS07) Equipment area - 6.2m x 6.7m Safe Play Area - 9m x 9m Ideal for age - 8-13yrs

Kilkari MS with Powder Coated Merry Go Round 04 Seater Shape:- Round Material:- MS with Powder Coated Age Group:- 6-12 Safe Play Area:- 2.2 m Dia

Providing & Supplying & installation of Aerial Stroller (ODFE01) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.12m x 0.35m Safe Area - 2.12m x 2.55m

Providing & Supplying & installation of Chest Press Single (ODFE02) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.2m x 0.7m Safe Area - 2.8m x 2.2m

Providing & Supplying & installation of Chest Press Double (ODFE02) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2.1m x 0.7m Safe Area - 4.0m x 2.2m

Providing & Supplying & installation of Seated Puller Single (ODFE04) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.2m x 0.8m Safe Area - 3m x 2m

Providing & Supplying & installation of Leg Press Double (ODFE05) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2m x 1.1m Safe Area - 3.5m x 2m

Providing & Supplying & installation of Triple Standing twister (ODFE08) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.6m x 1.5m Safe Area - 5m x 3.5m

Providing & Supplying & installation of Elliptical (ODFE09) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.1m x 0.6m Safe Area - 3.5m x 2m

Providing & Supplying & installation of Arm Spinner - 2 wheel (ODFE10) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 0.7m x 1.3m Safe Area - 2m x 3m

Providing & Supplying & installation of Abs Board Double (ODFE17) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2.4m x 1.4m Safe Area - 4.5m x 2.2m

Providing & Supplying & installation of Knee Hip Riser (ODFE18) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.06m x 0.95m Safe Area - 3m x 1.8m

Gazebo-Providing, hoisting and fixing at all level precast or reinforced cement concrete gazebo with all elements like roofing, string courses, bands, copings, columns, pillars beams, plinth beams, railings, benches, flooring, foundations including architectural design, moulding, arches, shapes, and applying proper texture and painting coats to suit a particular asthetic elements(trunck of tree, shapes of animals, birds, timber benching any element or structure representing culture or tradition) the cost of required centering, shttering and reinforcement of 25 grade and fibrous material etc. complete as per the instructions of Architect or Engineer - in- Charge

Providing and fixing in position UV resistant, fire retardant, virtually unbreakable and temperature resistant (-40° C to +130° C) Polycarbonate corrugated sheet of 2mm thickness for roof of approved make to match the roof profile at any height with G.I. J hooks bolts of G.I. clamps nuts & bolts or with self drilling fastener and EPDM washer etc. complete as directed.

Providing and fixing kerbstone with led lighting system as per following specifications: dimensions with vertical mounting legs with 10mm horizontal square shape mild steel reinforcements. Illuminated kerb stone having visible dimensions :-500mm x 150mm x 150mm.(as per irc - 86-1983 ) 80mm legs having ms reinforcements shal be embedded in bt/concrete road surface.the kerb stone should have kerb angle of 45 degree, with rubber plugs at both ends of the kerbstones (2 nos)having load carrying capacity - vertical : 1465kg, horizontal : 2349 (certified by govt. Recoganized bodies)having thermal stability -: -40 to +120 degree celcius (certified by govt. Recoganized bodies. Illuminated kerb stones including : ingrace protection and connector rating ip67, electrical wire -(as per is: 694), led strip (as per lm:80) standard. Including for electrical fixing -frp junction box consisting of - 10amp. Switch module power supply(smps)having input voltage - 230v ac, output voltage 36v dc, 2 pole mcb. Illuminated kerb stones having warranty for 3 years. illuminated kerbstone shall be fixed into cast-in-situ cement concrete of m20 grade at base, back filling and grooves, including dismantling, fixing, removal of dismantled material and cleaning etc. Complete. The colour of kerb stone shall be provided as directed by engineer in charge.

Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types,of exteri or grade,as per detailed drawings,conforming to I.S.:2202-1962 (Revised) with approved face veneers on both faces with /with out glazing and venetians in the positions shown on the drawings or as directed,all necessary beads,moulding and lipping,hold fasts,mat finishs tainless steel fixtures fastenings,finishing with french-polish /waxing complete. (with out door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter

Providing and fixing fiber glass rein forced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) with out ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete.

Providing and fixing in position,Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75 mm, 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick to prails 47.62 x 44.45 mm x 3.00 mm thick, vertical style 47.62 x 44.45 mm,3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12 mm thick both side laminated phenol bonded particle board panels for bottom panels etc.,I.S.I.mark,heavy duty,Hydraulic floor spring of 150 Kilogram capacity,having heavy duty concealed lock,necessary beading,glazing clips,PVC gaskets,250 mm length aluminium to wer bolts,150 mm dia.padhandle,etc.as per detailed designand drawing or as directed by engineer in charge including allmaterials,labours,andequipment etc.complete

Providing and fixing collapsible steel gate in one/two leaves with hot rolle dvertical channels of 18x9 x3 mm minimum size,crossings of M.S. flats of size 18 x 5mm Tor Esection forrunner of minimum 40 x 6 mm size for flange,M.S.flat for top runner of minimum size 40 x12 mm with roller wheels confirming to grade F.G.150 fitted with snap heade drivets of minimum size 6 mm max.spacing of vertical channels be 100 mmen closed gate position and clears pace of 150 mm between two sets of crossings with hold fasts,stoppers,spaces,handles,locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983).

Providing and fixing in position (as per 1868/1982) Alluminium sliding window of three tracks with rectangular pipe 95x38.10x0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92x31.75x1.30 mm at weight 1.070 Kilogram/One Running Metre. Top and side track section 92x31.75x1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40x18x1.25 mm at weight 0.417 Kilogram/One Running Metre. Interlocking section 40x18x1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40x18x1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer incharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing innyl on casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box

Providing and fixing frame with / without ventilator of size as specified with Country cut teakwood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Providing and fixing in position powde rcoated aluminium louvered windows /ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type,5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing and laying telephone black /Amba White /Cadbury brown/ Rubyred/ Ocean Brown granite stone of 18 to 20 mm thick for door frame /dado /window boxing etc.On C.M.1:6 including filling joints with polymer base fill ernosing /moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black backlite seat with all necessary pipe connection etc. complete.

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing white glazed earthen ware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Providing and fixing 450 mm x 550 mm size superior type Belgium mirror with 16 mm dia. nickel plated towel rod etc. complete.

Providing and fixing chromium plated towel rod 16 mm dia and 75cm. In length including all accessories complete.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing on walls/ ceiling /floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stackingt he same in PWD chowky or as directed etc. Complete

Providing and fixing on walls/ ceiling /floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls /ceiling /floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing 15 mm dia. Screw down bib /stop tap of brass including necessary socket union nut complete.

Providing and fixing 25 mm dia. Screw down bib / stop tap of brass including necessary socket union nut complete.

Providing and fixing screw down 15 mm dia. Wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 25 mm dia. Wheeled stop tap of brass including necessary sockets /union nut complete.

Providing and fixing screw down for 50 mm dia. Wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing push cock (Self closing tap) symet type of 15mm dia.including necessary socket, testing etc. complete.

Providing and laying for 225. mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and fixing 50 mm dia meter water meter with non-return valve including strainer, sockets /union nut and including water meter box making locking arrangement and lock. [without chamber]

Providing andc onstructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channel shalf round G.S.W. pipes, Brick Masonry, plastering from inside and air tight with 75 mm thick R.C.C. cover medium duty 140 Kilogram etc. complete.

Providing and fixing ISI1729/2002 grade 100mm dia Cast Iron Soil Pipes With lugs including plug bend necessary fittings such as bends, tees, single junction, double junction, slottedvent, off sets on wall orinto the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means of galvanised Mild Steel bracket of 30x5mm plate and 8mm square rod with Galvanised Iron clamp with wash erasper design, drawing and as directed to keep pipe 50mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of white oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Providing and fixing P.V.C. Rain water pipes of 160 mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming toI.S.13592-1992 including proper rain water receiving recess with P.V.C. plug ,bend, necessary fittings ,suchas ,offsets,shoes,inluding fixing the pipe on wall lusing approved wooden cleats projecting 25 mm to 40 mm from face of wall a fixing with clips of approved quality and One Number filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. ormasonry blocks, including necessary scaf folding and maintenance for 3 yrs for any leakages or dislocations of pipes.All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing H.D. P container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as in let,outlet over flow pipe inclusive of all tanks capacity between 1000 to 20000 liters

Providing and fixing 45 cm wide mild steel ladder of 40 mm x 6mm mild steel flat stringers and steps of 18 mm dia.mild steel bar for water tank including fixing it in(1:2:4)M-15 cement concrete block 60 cm x 30 cm x 30 cmand painting the ladder complete.

Excavation for foundation in soft strata which does not required blasting up to 1.5 Mtr. depth including removing the Excavated material up to a distance of 50 Mts. beyond the building area and lift. (PWD-DSR 2015-2016) P-5 / I-A-1

GARDEN SOIL :- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size Free from stones rubbish like dried grass roots and other such materials. The soil should be fresh be measured by measuring box (Farma) Item includes royalty charges, octroi, corporation Tax Transporting, loading – unloading etc As derected by Engineer-Incharge.

Preparing Shrubbery :- Excavating the round to required depth of 30cms, removing and conveying unwanted stuff to a required excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil & manure toughly well, leveling , watering on previous As derected by Engineer-Incharge.

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms.

Providing and fixing mild steel grill gate as per the detailed drawing including hinges,locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogram. to 20 Kilogram. Per Sq.m.)Spec.One Number: As directed by Engineer- in-charge.

Providing & Fixing FRP Entrance Gate 5.6 mt Length and 2.5 mt height (Quation) As derected by Enginner -in- Charge. Quotation TMC/CE/405 dated 02/12/2022

Providing and fabricating structural steel work in rolled sections like joists, channels ,angles,tees etc.as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted /welded connections with out connecting plates, braces etc.and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Providing and applying Ferro cement cladding of reinforced concrete with thin walls that's made of cement mortar and closely spaced layers of wire mesh on existing M.S. framework with thickness of 20-25 mm.

Providing, supplying, fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/ One Square Metre)

Aviary - Providing and fixing Galvanized Iron Woven GI Wire Meshes made up of 0.6 cm spacing and 3.00 mm diameter wiring on the existing MS Sturctural Framework and finished with approved shade of powder coated paint. Area - 2500 sq.m

Providing and fixing of seating for Play area in FRP (Fibreglass Reinforced Plastic) Umbrella - Size - 1.2m Dia x 3m height. To be made in FRP cladding on premade MS framework on RCC foundation to support MS structure. Stools - 0.45m Height x 0.4 m Radius

SITC, erection and transportation of LED Signage of 'GLOW GARDEN' made in 4mm Arcylic male and female covers Lazercut and Moulded, each letter of size 15m x 1.5m x 0.2m. Source: LED Modules, Power :3Watt, Color: RGB, IP 65 with IP67 Meanwell driver. Cost includes the Stress to mount the signage. Cat.Ref: GLO-SIGN of make Lumen craft/Lightman/departmental approved make including cost of material and conveyance to work spot etc complete as directed by the departmental authorities

Providing and supplying FRP (Fibreglass reinforced plastic) Statue of the given shapes and designs of size: 1m (Length) x 1.2m (width) x 0.15m (depth)

Providing and supplying FRP (Fibreglass reinforced plastic) Statue of the given shapes and designs of size: 0.6m(Length) x 0.3m(width) x 0.45m (height)

Watch Tower (Tabla Theme)– 4m Dia. 7m Height. Viewing deck height - 4.5m Circular RCC column of 750mm dia. to be erected to support deck area. Deck slab to be constructed in RCC 150mm thick. Casting of slant round beams supporting deck slab to be rested on central RCC column. Staircase of 1.2m in width in RCC along the MS frame structure Cladding - MS framing around central RCC column . base radius -2.5m and top radius acting like railing - 4m. Application of epoxy coat and oil paint as approved by Architect. Roof - Tensile roof supported on MS frame structure - Radius - 3.5m

Providing and Fixing Topiary Garden Sculpture – Mural made in MS structure frame work covered in wire mesh from outside with vegetation on framework to get desired shape Height 2.5m x width 1.0-1.2m x thickness 0.75m

Providing and Fixing FRP Musical Notations of size 12m (length) x 2.5m (height) x 0.15m(thickness) on existing Stage Backwall supported with MS base structure.

Providing and fixing sculpture in FRP (Fibreglass reinforced plastic) . Premade in MS framework or clay as per desired shape and design. 0.75m x 0.50mm x 0.1m PCC base, Statue Dimension – 0.6m(width)x 1m(height) x 0.3m (depth)

Providing and Fixing FRP notation Sculpture, free standing made up of FRP Cladding and MS support framework as per given designs. Size - 2.5m(width) x 0.45m(thickness) x 6m(height).

Providing and Fixing FRP notation Sculpture installation made up of RCC base structure of size 0.9m x 0.9m x 0.3m and Notation installation attached on it made up of MS Structure framework and FRP Cladding of size 1.5m x 4m Base in RCC and finished in FRP. Base size – 900mm x 900m. FRP installation size – 1.5m x 1.5m x 4m height

Providing and fixing 50mm diameter and 1.5 mm thick vertical and top Stainless steel hand railing in S.S.304 Grade with Stainless steel square / circular pipe bracing of size 32 mm x32mm x1.5 mm in 3 rows including fabricating ,fixtures, errecting, ecessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

GRC - Glass Reinforced Concrete Roman columns to be provided and fixed of 12' height and 0.5m dia (as per design shared by architect)

Providing and fixing GRC (Glass reinforced concrete) cladding on the premade m.s framework for are above column comprising of (Architrave/Frieze/Cornice) size - 1.5m(height) x 25m(length) x 0.75m (Thickness) to be made as per design shared by architect

Providing and fixing M.S. pergola a structure. Column height - 2.7m dia. 200mm. Rafter pipe - 1.8m length and 50mm diameter with metal swing in powder coating size - 0.6m x 1m

Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types, of exterior grade, as per detailed drawings, conforming to I.S.:2202 - 1962 (Revised) with approved face veneers on both faces with/without glazing and venetians in the positions shown on the drawings or as directed, all necessary beads, moulding and lipping, holdfasts, mat finish stainless steel fixtures fastenings , finishing with french-polish/ waxing complete. (without door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter

Providing and fixing in position.(as per I.S.1868/1982)Aluminium sliding window of two tracks with rectangular pipe having over all dimension 63.50x38.10x1.02mm at weight 0.547 Kilogram /One Running Metre.and window frame bottom track section 61.85x31.75x1.20 mm at weight 0.695 Kilogram /One Running Metre.Top and side track section 61.85x31.75x1.30 mm at weight 0.659 Kilogram /One Running Metre.The shutte rshould be of bearing bottom 40 x18 x1.25 mm at weight 0.417 Kilogram /One Running Metre.Inter locking section 40x18x1.10mm at weight 0.469 Kilogram /One Running Metre.And handle section 40x18x1.25 mm at weight 0.417 Kilogram /One Running Metre.and top section 40x18x1.25 mm at weight 0.417 Kilogram /Running metre.As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking latch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc,complete.With powder coating with box

Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 gms per sqm using surface roller and protecting from falling dust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1 :8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )

Providing and laying of cobble stone of size 4"x4"x3" with 25mm thickness

SS Dust Bin two sides for extra strength during oscillating movement. Oscillating arrangement for easy unloading of Garbage. Area :0.765 Sqm , Capacity In Litres 42 Ltrs, Height : 0.92m

Providing and fixing of fountain above existing well along with necessary fabrication, lights and support as per design and well diameter

Excavation for foundation in earth,soil soft all types,sand,gravel,soft murum including shoring and strutting,dewatering as necessary and disposing off excavated stuffas directed etc. complete. ( By /manaual Means )a) Upto 1.50m lift Normal Rate

Excavation for foundation in hard murum includings horing and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.a) Upto 1.50m lift Normal Rate.

Excavation for foundation in soft rock ingcluding shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.a) Upto 1.50m lift Normal Rate

Excavation for foundation in hard rock by chiselling and we dging orline drilling including shoring and strutting,dewatering as necessary and disposing off excavated stuffas directed etc. complete.a) Upto 1.50m lift Normal Rate.

Excavation for foundation of structure as per drawing and technical specifications including setting out,construction of shoring, brushing, removal of stumps and other deleterious matter,dressing of side and bottom and back filling with approved material etc. complete. (in marshy soil by mechanical means)

Dewatering on BHP basis by using water pump including diversion of stream,providing coffer dams,earthern bunds etc.as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 10.0to19.0BHP pump etc.complete.(prior approval of Super intending Engineer will be necessary)

Providing and laying plainin situ/ready mix M-30 cement concrete of trap /granite /quartzite /gneiss/ crushed stone metal mechanically mixed,placed in foundation and compacted by vibration including necessary bailing out water,curing curing concrete batch mix plant/pan mixer with fine agree gates of required specifications (VSIs and finely was hed etc)(excluding dewatering by pump) for 14 days RCC Grade.With Concrete Mixer

Providing and laying in situ/ready mix M-30 plaince ment concrete of trap /granite /quartzite /gneiss metal for cast incitupiers, abutment, returns,wings etc.including provision of "V"shaped false joints to form suitable panels on the faces to approve design with compacting by vibrating and curing complete,including plywood /steel form work centering (excluding dewatering by means of pump)and including bailling out water and curing finishing in CM1:3etc.complete.as directed by engineer incharge basic rate shall be increased for height above 5.00 m in following hmanners

Providing and laying in situ/ready mix controlled M-30 cement concrete of trap /granite /quartzite /gniess metal for reinforced cement concrete caps over piers and abutments including necessary sacffolding plywood/ steel form work,compacting by vibrating,finishing in CM 1:3 and curing etc complete (Excluding reinforcement) With reversible drum type mixer /concrete batch mix plant (panmixer).with fine agreegates of required specifications ( VSI sand finely washed etc )

Providing and laying in situ/ready mix M-30 controlled cement concrete of trap/ granite / quartzite /gneiss metal for RCC work in solid /deck slab etc.including ramming, vibrating, curing, formwork,centering and finishing in cement plaster excluding rein force ment etc.complete.(with fully automatic micro process or based PLC with SCADA enabled concrete batch mix plant /pan mixerand fine agreeg at es of required specifications (VSIs and finely was hed etc) i)Height upto 5m,norma lrate.

Providing, cutting, bending, hooking,tying and laying in position TMTFE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete.

Providing tar paper bearing including laying in proper position etc. complete.

Providing expansion joints with 25 mm thick bituminous pad as per detailed drawings etc.complete.

Providing vent holes 100 mm diameter GI pipe in the slab and wearing course with iron grill at the top and GI pipe at bottom as per drawing etc. complete.

Providing railing of cast in situ R.C.C posts with (M-20) cement concrete trap/ granite /quartzite /gneiss metal size 150 mm x150 mm x1.240 mm and horizantal 3 nos.at distance 370 mm C/C and bottom bar 150 mm above kerb as per the detailed drawings (including cost of reinforcement) scaffolding,steel centering,plywood /steel form work etc.complete.The C.M.1:3 plaster is considered for rendering uneven and honey combed surface only.Newly laid concrete shall be covered by gunny bag,plastic,tarpaulin etc.(Wooden centering /form work will not be allowed).

Providing and laying 12 mm thick mastic asphalt wearing course on top of deck slab excluding prime coat with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface including providing antiskid surface with bitumen precoated fine grained hard stone chipping of 4.75 mm nominal size at the rate of 0.005 cum per 10 One Square Metre and at an approximate spacing of 10 cm center to center in both directions, pressed in to surface when the temperature of surfaces not less than 100 deg C,protruding 1mm to 4 mm over mastic surface as per clause 515 etc. complete.

Back filling behind abutment, wing wall and return wall as per drawings and technical specifications etc. complete. (by granular material)

Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Removing iron pipe raling having wooden R.C.C. or C.C. or iron post and stacking the materials as directed etc. complete.

Providing and fixing coloured glazed earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting,inlet pipes and stop tap brackets for fixing the cistern 32 mm dia. P.V.C.flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap soil pipe connection up to the outside face of the wall.

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite /Amba White /Catbary brown /RBIred/ Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

SITC of Interactive Touch Floor Dimensions: Ø50; Material : Stainless steel +12mm tempered glass; Voltage: AC24V ; Power:25W ; without driver

Providing and fixing Multi Purpose Scrambler Set(PACL26) Equipment area - 11.8m x 3.4m. Ideal for age - 8-13yrs

Providing and fixing Balancing Bridge (PACL03) Equipment area - 6.2m x 1.05m Safe Play Area - 8.6m x 2.5m Ideal for age - 6-12yrs

Providing and fixing Topiary plants- Approximate height of the plants 5m to 6m planted in pots of various diameter.

Providing and fixing Topiary plants- Approximate height of the plants 3m to 4m planted in pots of various diameter.

Providing and fixing Topiary plants- Approximate height of the plants 6.5m to 7m planted in pots of various diameter.

Providing and fixing Topiary plants- Approximate height of the plants 6.5m to 7m planted of various diameter.

Providing and fixing Drinking water fountain with front push button - Vandal resistant button to activate the water flow. Net weight approximately 23.6kgs. Brush stainless steel finish. Waterways are lead-free in materials and contruction. Limited 1 year warranty

Providing and laying in situ/ready mix M20 RCC of trap/granite/quartzite/gneiss metal for RCC work of kerbs including scaffolding, compaction, formwork finishing and curing etc. complete. (excluding reinforcement, with fully automatic microprocessor based PLC with SCADA enabled concrete batch mix plant/pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc ).

Providing cast in situ/ready mix M20 grade cement concrete for head walls of retaining walls etc. including necessary formwork, compaction, finishing and curing etc. complete. (with reversible drum type mixer/concrete batch mix plant (panmixer) with SCADA

Providing and supplying waterproof tensile mild steel Modular Roof Terrace Structure with 15 Feet height as per drawing and as per instructions from Engineer in charge.

Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 80 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both sides, fixing in cement mortar 1:3 and curing etc .complete.

Excavation for foundation of structure as per drawing and technical specifications including setting out,construction of shoring,brushing,removal of stumps and other deleterious matter,dressing of side and bottom and back filling with approved material etc. complete. (in marshy soil by mechanical means)

Removing excavated material including loading and unloading with 20 km lead

Providing and suppying natural exterior pebbles stone of different sizes ranging from 10 mm to 80 mm wih transport and loading.

Providing and laying Polished Tandur Stone flooring 25mm to 30mm thick required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

Supplying natural sand for sand pit

Providing and fixing of Butterfly mural for photo booth to be made in FRP - Size 1.2m (width)x 1.5m(height)x 0.05m (thick). FRP cladding on MS frame structure with MS support from ground to be fixed on RCC base of 150mm.

Butterfly mural for photo booth to be made in Metal - Size 1.8m (width)x 1.2m(height). MS plate structure with MS support from ground for mural and forming seat out of it, to be fixed on RCC base of 150mm.

Providing and fixing Metal Sculpture - size 2m(length) x 2.5m(height) Stainless Sreel frame structure as per design with oil paint and epoxy coating paint finish to be fitted on on RCC base of 100mm.

Providing and supplying of Butterly size - 0.8m x 0.8m. Make FRP

Gate in FRP 3M(length) X 2.7M(height). Thickness 0.45m dia Providing and fixing FRP (Fibreglass reinforced plastic) cladding on the premade m.s framework. Excavation for colum footing to be made till 750mm deep with rubble soling and PCC base of thickness 100 mm with footing of RCC.

Providing and supplying metal letter in SS 304 for name of the park at entrance. Each letter size approx 0.6 (width) x 1.2m (height)x 0.15m (thickness)

GRC Statues - Mould made in Clay and MS framing and cladded with GRC fitted on pedestal (0.75m x 0.75m x 0.75m) made in brick work and GRC cladding for same. Statue dimension - 0.6m x 0.6m x 4.5ft height. Transport & fitting extra

Sandstone square paving stones, for pavement of thickness 20-30 mm and of mix sizes, colour: Beige, Brown, Grey, Red, White.

Providing and fixing in position coloured anodized aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening such as 5mm thick clear float glass etc. complete. Note While arriving at the rate of item of item weight at 6.90 Kilogram/ One Square Metre is considered.

Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area .

Providing and fixing metal frame structure, interconnected with metal supports to each other from top and anchored at bottom to be covered with ACP cladding & provision of outdoor LED lights inside. 10ft height & 10ft wide. To be provided at a distance of 0.75m centre to centre distance. Total - 12Nos.

Providing anf fixing FRP hand installation around existing trees

Providing and fixing curve, arched basalt stone door lintel in wall of given size. The stone of size given by architect cut in shape and two adhacent side to dressed fixed in 1:1 cement mortar in superstructure including carving dressing, scaffolding and watering including transportation loading unloading and all labour artistic work complete to the entire pecification of the architect and engineer-in-charge include etc. complete. (Sanctioned rate from Naglabunder estimate)

Supply Installation testing and commissioning of Decorative Pole Technical Description :- 2955mm pole made of gravity die cast aluminium (LM6). Bottom Florus decorative element dimension details (245mm Dia x 206mm Height). Decorative base made of gravity die cast aluminium (340mm dia x 516mm Height). Decorative element (190mm dia x 550mm height) mounted on base and continuously tappered decorative flutted pipe made of gravity die cast aluminium (126mm Bottom Dia & 112mm Top Dia x 1000mm Height) fitted on decorative element with decorative die cast aluminium embellishment for mounting four arm bracket. Bracket stem made of MS square 120mm with decorative die cast aluminium embellishment of 375mm height with flower bud design on top 202mm. The four arm bracket made of gravity die cast aluminium extending from stem is spruced up with Leaf designer embellishment and facilitates the fitment of post top luminaire at 445mm on four side from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 200mm square x 12mm thick steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at CC 140. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension within +/- 5% tolerance. After fabrication, entire pole is shot blasted (Inhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options and Gold / Antique shade as special colour options.

Fitting:Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Pole-top luminaire with Symmetrical light distribution. Luminaire made of spun aluminium, die cast aluminium and non corrosive stainless steel fasteners. Cast aluminium magudam attachment added for aesthetics. Prismatic diffuser. Suitable for mounting on Ø76 mm OD pipe. Pure polyester powder coated graphite grey & gold / anthracite grey & gold / jet black & gold. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 495mm diameter x 960mm height. BIS Certified for Luminaire.

Supply, Installation, Testing and commissioning of 3660mm height Pole made of circular mild steel pipe of two section (grade YST 210) Bottom section 139.7mm Dia x 3.6mm thick with 1000mm Height & Top section 76.1mm Dia x 2.6mm thick with 2648mm Height. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 110mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500 mm from its base plate. The control gear tray is prewired with single core 2.5 Sq.mm PVC wire, 6A SP MCB of Approved make and 32A stud type 4 way terminal block for loop-in / loop-out arrangement and to be connected with lugs and has a 5amp, 2 way terminal connector for luminiare and a provision for earthing. Mild steel mounting plate (Base Plate) 200mm 16 Square x 12mm thick Steel of grade E250 to IS 2062: 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at center to center 140mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication, entire pole is to be shot blasted (Inhouse). After shot blasting the pole is to be coated with Epoxy zinc rich phosphate primer and subsequently finished with pure polyester powder coating or using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply Installation testing and commissioning of 2 x 6W Decorative up down light Technical Description :- Wall-mounted compact downlight. Beam angle 15° / 25° / 40°. Luminaire made of extruded aluminium section with inner grooves to fix the top and bottom frame (grade 6063) Ø100 x 2.5mm thickness, pressure die-cast aluminium glass fixing top and bottom ring of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass of 4mm thickness. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression. 3 core 1sqmm cable & 200mm length cable via black PG7 cable gland. Pressure die cast aluminium base for surface mounting on wall. Protection class IP65. Mechanical resistance IK07. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 6500K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Driver shall be of approved make or Equivalent. Driver is a Fixed constant current driver with an output current of 300MA, 36Vdc ,12W Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >80%, Power factor >0.95, THD <10%, Surge protection 4KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Luminaire dimension : 145mm length x Dia 100mm width x 210mm height. Led Source shall be of Nichia or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. BIS Certified for Luminaire.

Supply installation testing and comissioning of Decorative Pole of 4.13m The Total height of decorative post top with MS Conical pole shall be of 5.7 meter height. Pole Description : A Pole made of continuously tapered circular hot rolled steel grade E250 to host the decorative post top Light fixture shall be of conical shape with bottom dimension of 230 mm at the top of base plate to 180 mm at the top of the pole to host a decortaive post top lantern. A decorative base of extruded aluminium is of 400 mm dia x 1240 mm height x 5 mm thick shall engulf the conical pole and in aluminium shall have circular ring at its top with a vertical groove design. Bottom of the- MS conical pole shall be with a base plate of aluminium Base plate made of steel grade E250 & foundation bolt of grade 4.6. with a size 450 mm x 450 mm x 16 mm thick having a center to center distance of 375 mm with gusset welded between pole and base plate for additional support and stability. The base plate shall have 4 elongated holes of 38 mm x 19 mm to suit M16 bolts @PCD of 530 mm. Galvanised Founation bolts of 4 nos of M16 x 750 mm along with 2 sets of Plain washer and Spring washer along with 2 nos of M16 nut. per foundation bolt. Inner service door made of MS at 320 mm height x 90 mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. Outer portion of the junction box will be covered with extruded aluminium with a single door. The bottom of the door is loacted at a height of 500mm from its base plate. The Bottom of the decorative base has a aluminium cover of dia 650 mm to cover the base plate. The Service door with stainless steel harness at the bottom of decorative aluminium base shall have access to control gear tray to house a 32 amp TPN Stud type terminal block along with Three pole 6 amp MCB which are prewired with 2.5 Sqm copper wire to the 10A ,3 way terminal connectors for dual light source in the decortive post top. Pole Coated with zinc rich primer and pure polyester powder coating or epoxy zine phosphate primer and finished using environmentally stable polyurethane paint.

Supply installation testing and comissioning of Decorative post top lantern in 6061 grade aluminium with twin ring caps one at the top and other at the bottom located on the lantern along with MS concial post of thickess 3.0 mm varying from diameter of 216 mm to 180 mm to host post top lantern. Post Top Description: Decorative Post Top Light fixture in spun aluminium and with Cast aluminium componenets to have a diffusion at the top between the twin cap rings of spun aluminium, one ring at the top and other ring at the bottom seperated by a UV stablised opal PMMA diffuser with suitable gasket and caged in a decorative pattern of rectangular stripes in die-cast aluminium with a sectional dimension of 25mm x 10 mm for each strips. The over all height of the Post top is of 1570 mm height and outer dimension shall be of 585mm. Internal Dimension are circular caged pattern are of 410 mm dia with a height of 360 mm with 40W Led, available colour temperature of 3000K / 4000K / 5700K. Bottom cap aluminium ring houses a 60W led with suitable optics for a asymmetric forward throw light distribution as a fuctional illumination of the road and shall be with a co-related colour temperature of 3000K having a luminiare efficacy of minimum 75-80 lumens/watt. Both the top decorative symmetrical illumination and functional 23 illumination shall have a minimum CRI of 80. The Fixture shall have an IP rating of IP65 and IK rating of IK08 and with a light source of nichia / bridgelux / cree or near equivalent of SDCM 3 or less with L70B10@50,000 burning hrs. The constant current driver for 3000K and the functional illumination shall be of constant current non dimmable driver. Driver shall be of approved make. Driver shall have a PF of >0.95 and with a built in surge protection of minimum 2.5KV and shall be suitable for 230V/50Hz operation with +10% voltage tolerance. The entire Post top body shall be of aluminium in grade 6061 and duly coated with pure polyster powder coat of 80 micron thickness as per Specific RAL shade of Engineer in charge. External SPD of 10KV to be provided. Post Top Coated with zinc rich primer and pure polyester powder coating or epoxy zine phosphate primer and finished using environmentally stable polyurethane paint in brown. BIS Certified for Luminaire.

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Supply and erection of Hot dip galvanized Ring for installation of mini high mast suitable for 4 Nos of LED Flood lights. The outer dia of ring shall be 600 mm. The ring shall be of 50 mm dia B class pipe with three supports to Sleeve, the sleeve shall be of 500 mm length and 4 mm thick duly provision of 4 nos bols and shall be suitable to fit on Octagonal pole of 70 mm AF .

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Flood light luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 120W. Details as per technical specification attached.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative double bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The Tentative shape is enclosed herewith .The final design shall be got approved from Engineer in charge.

Supply, Installation, Testing and commissioning of 4270mm height pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2788mm Height. Decorative base made of Gravity Die- cast aluminium (245mm Dia x 206mm Height) in gold or black finish. The single arm bracket is a split constructed type, bracket stem made of MS Pipe 60.3mm Dia x 2.6mm thick, emerging from a Gravity Die cast mid section Aluminium embellishment in gold or black finish of 60mm with a clear height of 1150mm crowned at top from the collar and with a cast Iron decorative finial of 260mm clear height. The artistically curved single arm made of MS pipe 38.1mm Dia x 2mm thick, spruced up with MS Scroll with leafy embellishment at Center in gold or black finsh, is firmly held to the stem by way of cast iron clamps and the arm bears cast iron knobs at the one ends and other end facilitates the fitment of luminaire at 624mm from the vertical axis of the bracket stem. Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500mm from its base plate. The control gear tray is prewired with single Core 2.5 Sq.mm PVC wire, 6A SP MCB of approved make and with 32A stud type 4 way terminal block to take incoming cables with loop-in / loop-out arrangement and to be connected with lugs and has a 5 amp, 2 way terminal connector for luminiare and a provision for earthing. Any other internal cables and connections shall be covered in the contractors scope. Mild steel mounting plate (Base Plate) 230mm Dia x 12mm thick Steel of grade E250 to IS 2062: 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at Pitch Center Distance 180mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension and are within +/- 5% tolerance. After fabrication, entire pole should be shot blasted (Inhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey/ Anthracite grey / Black as standard colour options.

Supply installation testing and commissioning of Tier drop Luminaire of 40/50W. Decorative pendant / Hanging mounted compact street light. Type IV (Asymmetrical light distribution). Decorative luminaire made of specially contoured spun aluminium body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The luminaire have extruded aluminium heatsink for thermal management with vertical fin design for longerlife of the LEDs. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitablefor mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK09 (Polycarbonate diffuser). Pure polyester powder coated graphite grey / anthracite grey/jet black. Available colour temperature 3000K/4000K / 5700K as per TMC Engineer and as per application. Colour rendering index (CRI)>70. Standard Deviation colour matching 3 MacAdam. Led module with expected service life of at least 72,000 operating hours. Driver shall be of approved make and are a Fixed constant current driver with an output current of 1200 MA, 48Vdc,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency > 85%, power factor > 0.95, THD < 10%, internal Surge Protection 6KV of the driver. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / Lumiled/ cree or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension: 425mm diameter x height 407 mm / 437mm. BIS Certified for Luminaire.

Supplying and erecting LED Strip light 5m Length Max. 8 W/mtr IP65 class including necessary components. The LED Strip shall be protected with transperent PVC material.

Supplying and erecting LED Green Flood light fitting of 50W, including lamp, with PF>0.95, Class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specs no. FGODF/FLS-2

Supply and erection of BREEZA type decorative hot dip Galvanized single arm bracket of 1 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Supply and erection of BREEZA type decorative hot dip Galvanized double arm bracket of 1 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 7 mtr long pole

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 5 mtr long pole

Supplying and erecting integrated LED flood light fitting Max. 20W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 2000 Lumens, min. efficacy of 100 lumen/W, CRl>70, CCT upto 6500K, THD<10%, p.f.>0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70850, including driver with U shaped bracket with 5 Years warranty as per specification No FGODF/FLS2.

Supplying and erecting LED square / circular Max. 18 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED

SITC of high quality multicolour spot light,Power: 20W,Colour: RGB, Protection. Rating : IP65, Beam Angle: 20⁰/40⁰, Body:Die casted, additional wall mount arrangements for fixing the lights. Optics: Specially designed to minimized hot spots & fringing, in colour mixing applications. Power Input: DC 24V ( without DC Driver) Make: Leksa Lighting/ Guzzini/Aultra Lighting/ LaMartinie

SITC of high quality long throw multicolour linear wash light, Protection Rating: IP65, complying to BIS standards IS 10322 (Part 5/Sec 1): 2012, and having CEcertification against standard EN 61547: 2009, EN 60598-1:2015, and EN 61347-2-13:2014. Mounting Structure: Additional wall mount yoke arrangements for fixing the lights. Rotation view: Inbuilt body rotating angle in degrees punched in the yoke/ rear sides for uniform rotation angle to get the desired effects. Power consumption : 50w, CCT : RGB, (as per the design approval) Beam Angle 25⁰x 25⁰, Control: DMX 512, Channel: 4 CH, Body : DIE casted / extruded aluminium, Hot and light distribution: Optics designed to minimix=ze hot spots & fringing in colour mixing applications.

SITC of Power Driver for above lights, Power : 200W, INPUT: AC 110-240V AC, 50HZ,OUTPUT: DC 24V, Protection rating IP66, Constant Voltage (CV) +Constant Current (C.C) output, High efficiency up to 93%, orking temperature (case temperature)-45-+45⁰C, Protection: Short circuit / Over current/Over voltage/ Over Temperature, Comply with harmonic current limit per EN61000-302 Class C( 50% load), Meet 4kV surge immunity level.

Supplying LED concealed type foot / step light with aluminium body for indoor / outdoor application suitable for 4W - 6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with minimum 1 year warranty as per specification No. FG-IDF/LED.

SITC of 5 core DMX cable comprises tristed pairs with shield support for carrying of data. Featuring five/ threee pin connector support, these DMX-cable options are suitable to use with different type of fixtures. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. Comprises pairs with a cross-section of 0.34 mm2 and general double screening. The external ultra-flexible sheath provides mobility of use and is very easy to coil. Make: FALCON/BELDENL/GURASTRONICS

Supply Testing Commissionning of DMX controller, 2 ports output which can control 2048 plus DMX pixels. IT shall support Off-line control & play back content stored in the SD card up to 64GB and also i support at least 50 different scenes. It should be with digital touch screen dispaly for changing modes, it support master slave configuration to accommodate more DMX addresses (8x 512 pixels Slave device) with outdoor encloser to protect from sunlight dust and water.

Supply, installation, Testing and Commissionning of 24V 5W RGBW or single colour as per requirement,DMX addressable Dot (coin) with buit-in decoder along eith IP66 with clear/milk diffuser, arrangement for connecting supply and control signal cable complete with all fixing mechanism such as screw or silicon gum. The coin shall have chipset of Cree/Osram/bridgelux.

Supply, installation, Testing and Commissionning of 24V max 2.1W RGB SPI addressable Dot ( Dome coin) with ic uc 1903 or equivalent chip/ built in decoder along with IP66 clear/milk diffuser, having 6/8 inch 4 core 1.5 sqmm copper fixture interconnecting cable of suitable size,T connector for supply and control complete with all fixing mechanism such as screw or silicon gum or industrial high strength adhesive tape.

Supply, installation, Testing and Commissioning of 24V max 2.1W RGB SPI addressable Dot ( Dome coin) with ic uc 1903 or equivalent chip/ built in decoder to be installed at height more than 10 mtr, along with IP66, having 6/8 inch 4 core 1.5 sqmm copper fixture interconnecting cable, T connector of suitable size for supply and control complete with all fixing mechanism such as screw or silicon gum or industrial high stregth addhesive tape. the job includes erecting the coin with the use of Hydra or hydraulic vehicle.

Supply, installation, Testing and Commissioning of SPI pixel controller, it shall support off line control & play back content stored in the internal memory and also support at least 200 different scenes and min 7 custom effect options. With wifi connectivity for changing modes along with out FRP/ PVC enclosure box to protect from sunlight, dust and water.

S &EM 15 Female Supply Cable 1M 3 Pin

S &EM 15 Extension Cable 1M 3 Pin

16 W Bollard Lights

S & E LED driver CV250W24V10.5AEBV250S024SV

S & EDMX DECODER_RGBW_12V_480W

S & E Instruction Forwarder Ranger/Compass (AC) / Strip

S & E 1Mtr wire 5pin IP67 Female Connector RGBW

S & E 1M EXTENSION WIRE 5PIN IP67 RGBW

S & E Aliminium Channel with Diffuser ( Running Meter)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 4 core 4 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Providing & erecting epoxy outdoor / indoor end termination kit for LT PVC armoured cable 2.5 to 16 sq mm. cable, with necessary material as per specification No. CB-JT/LT

Providing & erecting epoxy outdoor / indoor end termination kit for LT PVC armoured cable 25 to 50 sq mm. cable, with necessary material as per specification No. CB-JT/LT

Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and erecting mini feeder pillar with 415V, 200A FP MCCB as incomer and 2 outgoing circuits with HRC fuse base and cartridge of 100A with aluminium bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket and enclosure must be dust proof, rust proof, vermin and water resistant, having slanting top and erected on angle iron/ GI frame in provided C.C. foundation complete as per specification no. SW-MFP.

Supplying, erecting & marking SP MCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Supplying, erecting & marking FP MCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FP MCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no.SW-RCCB/RCCB

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Point wiring for light/fan/bell in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification no. WG-PW/SW

Point wiring for independent plug in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire,flush type switch, earthing and required accessories as per specification no. WG-PW/SW

Wiring for plug on board with flush Switch socket, copper wiring and earthing as per specification no. WG-PW/SW

Supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame

Supplying and erecting PVC Surface modular double mounting plate 12 module complete duly erected

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation

Supplying, installation, testing and commissioning of IP camera 4MP 1/3" CMOS image sensor full HD video resolution max 2688 x 1520, 20/30 fps True D/N IR Bullet / Box camera, 2.8-12 mm motorised lens, Auto Back Focus, High Light compensation, 120 dB and above True WDR, audio capture capability, 3 streams, ONVIF compliant, SD card Slot,with IP67 housing and mount with dehumidification feature with accessories such as mounting brackets/structures /fixtures etc. necessary to mount the camera on pole, etc. Smart codec H.264+ / H.265+, Certification from EU,UL & CE-EMC,FCC.

Supplying, installing, testing & commissioning of 32/40 Ch. Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI/VGA outputs, provided HDMI output of 4K resolution or VGA output with output up to 1920 × 1080. Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 250Mbps with minimum 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps selfadaptive Ethernet interface, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specification no. CCTV-NVR

Supplying, installation, testing and commissioning of 6000 GB Hard Disk for video Survelliance Equivalent to : Western Digital

Supplying & erecting 32" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x550x480 mm) as per specification no. WG-NAS/RAK

Supplying, fixing, and configuring 4 -ports unmanaged Din -Rail Industrial POE gigabit switch with 4 nos. 10/100/1000M POE Ports, 2 nos. 1000 Mbps SFP for uplink

SITC UPS - 600 VA at Junctions with 2 hrs back up to be housed with POE switch rack.

Supplying, erecting, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS, with backup time of .......hrs. PWM & IGBT based, with 0.8 to unity output pf complete with all protections as per specification no. AP-UPS

Supplying and installing FR PVC sheathed Aluminum foiled wrapped over all tinned copper braided HDPE insulated copper cat-6 STP cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying, erecting & terminating XLPE armoured cable 2 core 10 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no.CB-LT/AL

Power supply kiosk of size of 400 mm x 400 mm slanted made from 14 swg powder qouted GI sheet duly equipped with lock & key and magnet lock supported on GI pipe of min 100 mm dia & suitable height and complete with earthing stud necessary foundation and pipe type earthing as per drawing enclosed. Job includes erection of provided MSEDCL energy meter

Supplying and installing PBT loose tube HDPE sheathed armoured single mode optical fiber cable with 6 fiber, core dia 9/125μm (OS1/OS2) 10 GBPS speed compliant to IEC 60793/IEC 60794 standards in provided pipe/trench complete

Supplying and erecting brackets for installing CCTV camera on pole

Supplying and erecting ISI mark G.I. pipe pole ‘B’ grade 80 mm dia 6 m long with pole cap, base plate in provided foundation as per specification no. OH-PL/GIP

Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal,(45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered,with necessary curing and finishing complete. (for 6 m pole)

Second Year Comprehensive Maintenance of all electrical works (2.5% of electrical Cost)

Third Year Comprehensive Maintenance of all electrical works (4% of electrical Cost)

Fourth Year Comprehensive Maintenance of all electrical works (5.5% of electrical Cost)

Fifth Year Comprehensive Maintenance of all electrical works (7% of electrical Cost)

MSEDCL Charges

Hiravati Enterprises