138WE/L-132/2025-26

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exc 15cm thick (below or above ground level ) and removing debris off the premises complete all as specified and as directed by Engr-in-Charge.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or as directed by the Engr-in-Charge.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and as directed

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and/ or as directed by Engr-in-Charge.

M&L for preparation of new plastered wall surface of any description and applying two coats of cement based paint over a coat of chalk whiting complete all as specified and as directed.

Taking down shutters of any description not exc. 1 sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description exc 1 sqm not exc 2 sqm each complete all as directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and/ or as directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge or thickness including nainital or similar pattern complete all as specified and/ or as directed by Engr-in-Charge.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and/ or as directed by Engr-in-Charge.

S&F 0.63mm thick black, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and/ or as directed by Engr-in-Charge.

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and/ or as directed by Engr-in-Charge.

S&F fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and/ or as directed by Engr-in-Charge.

Preparation of newly or previously untreated steel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and/ or as directed by Engr-in-Charge.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section including dismantling, complete all as specified and/ or as directed by Engr-in-Charge.

M&L for 2nd class soft wood clean sawn as in beading for edges of Ceiling, lining or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section including dismantling complete all as specified and/ or as directed by Engr-in-Charge..

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding including dismantling complete all as specified and/ or as directed by Engr-in-Charge.

All as per serial item No. 17 above, but as in ceiling.

M&L 6mm (5 Nos. ply) thick veneered decorative (Knotty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work, including dismantling complete all as specified and as directed.

All as per serial item No. 19 above, but as in ceiling.

M & L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:4 screed bed or bedding layer of mortar and dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated , including backing with thermocol sheets or as specified by manufacturers including dismantling all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc. laid bedded and pointed in any mortar.

M&L for cement concrete 1:4:8, type D-2, (40mm graded stone aggregate) 75 mm thick as in sub -floors, sub- bases, floors and pavings, etc. complete all as specified and/ or as directed by Engr-in-Charge.

M&L for Chequered cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments, laid over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.

M & L for 75 mm PCC 1:2:4 type B-1 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement complete all as specified and/ or as directed by Engr-in-Charge.

M&L forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection.

Material and Labour precast cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry with solid blocks, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

S&F for 30 mm thick 2nd class soft wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as directed by Engr-in-charge.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, including aluminium jali fixed in one side, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 Nos) hinges type B-21 100mm long (3 Nos) suitable handle (1 Nos) etc. complete all as specified

M&L sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F floor door stopper (Length of cover plate ) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed.

S & F 1000 litres capacity rotational moulded polyethylene water storage tanks inner and out white, two layers ISI marked (Cylindrical vertical, with closed top), hoisted with threaded cap and fixed in position all as specified in SSR Part I including all accessories (i.e. GI nipple etc), including provn of 20/25 mm dia spout for connecting inlet, outlet, over flow and washout pipes and including dismantling water tanks and removing to store exc 500 and not exc 1000 ltrs capacity complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 25mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

S&F 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR pipe and fixed in repair.

S&F in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule.

Taking up or down steel tubing 25mm to 32 mm bore including cleaning for refixing or removal to store. complete all as specified.

S&F 3-layer PP-R Polypropylene random copolymer) pipes 25mm dia SDR 7.4 (PN 16) stabilized and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain an brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floor etc. all as specified and directed.

All as per serial item No.44 above, but 32 mm bore pipe.

S & F Vitreous china wash basin white flat back size 550 x 400 mm excluding taps, waste, chain, plug and porcelain stopper including CI brackets of angle iron 65 x 65 x 6mm embeded in PCC block with PCC 1:2:4 type B-1 & CP grating with holes fixed in repairs, complete all as specified and/or as directed by Engr-in-Charge.

S&F in repairs, 15 mm bore, PVC connection pipe 600 mm long with PTMT nuts at both ends complete all as specified and directed.

S&F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible waste pipe for sinks / wash hand basins.

Supply only 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams).

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs all as specified and as directed by Engr-in-charge.

S&F in repair Soap dish fixed with and incl CP brass screws complete all a specified and directed.

S&F in repairs toilet paper holder of brass, chromium plated or stainless steel complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs CP wall mixer 3-in-1 system with provision for bath telephone shower and over head shower with bend pipe complete all as specified and directed by the Engr-in-Charge.

S&F in repair vitreous china wash down water closet (Pedestal), white (EWC) excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including connection to drain pipe and to flushing pipe antisyphonage pipe etc complete all as specified and directed by Engr-in-Charge. Make : CERA/JAQUAR/KOHLER.

S&F in repairs vitreous China squatting pan or Orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern and flush pipe) but including connection to 100mm dia trap 'P' or 'S', anti syphonage pipe etc complete all as specified and as directed by Engr-in-Charge.Make : Cera/Jaquar or equivalent approved make as approved by GE.

Supply only 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level, white, with inlet, ball valve, float and handle including bracket & flush pipe of polyethylene of low or high density or high density or PVC, 32mm dia, for low level cistern complete all as specified & directed by Engr-in-charge.

Supply only fancy type 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as specified and/ or as directed by Engr-in-Charge.

Taking down carefully sub main wiring/service wire of any description complete all as specified and directed.

Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead all as specified and directed for the following:-

One light/exhaust fan point controlled by one way switch complete all as specified and directed.

One switch socket outlet 6 Amps, 230 volts point on same board complete all as specified and directed.

One switch socket outlet 6 Amps, 230 volts point on independent board complete all as specified and directed.

All as item No 64 above, but using cables 4 Sq mm size.

Supply and fix lamp holder insulated body with back plate complete all as specified and directed.

Supply and fix switch piano flush button single pole 6 Amps 230 volts one way complete all as directed.

Supply and fix Socket 2 in 1, 6A flush type 5 pin 230 volts complete all as directed.

Supply and fix switch Socket combination 2 in 1, 6A flush type 5 pin 230 volts complete all as directed.

Supply and fix switch Socket combination out let multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as specified and directed..

Supply and fix ceiling rose, surface Bakelite three terminals complete all as specified and directed..

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways complete all as specified and directed.

Supply and fix in replacement of MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and directed. Make : Havells or equivalent of Indo Asian/Standard Havells.

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as directed. Make : Havells or equivalent of Indo Asian/Standard Havells.

Supply and fix submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x6.0 sq. mm + 1x6.0 sq. mm earth wire complete all as specified and directed.

Supply and fix in replacement LED light fitting 1 x 20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repalcement connecting and testing LED security light fitting 35 watt, 230 volt, AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp and bracket with impact and corrosion resistant incl thermal management in multiple optics including taking down complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 600 X 600 X 6mm thick buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the earth plate not less than 1.5 meters deep below normal ground level, connected with and including galvanised iron strip of size 25 x 4mm connected to main test point as directed as earthing lead by means of nuts, bolts and washers of galvanised iron protected by 40mm dia (medium grade) GI tubing, funnel, wire mesh, 20mm bore GI tubing (light grade) watering pipe, including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab of size 350 x 350 x 50mm reinforced with 8mm dia TMT bars @ 15cm c/c in both ways and 10mm dia MS handle (01 No) of suitable size for lifting of cover slab, charcoal and salt in alternate layers including necessary excavation and earth work in soft/loose soil all as shown in Electrical Plate No 3 of SSR Part-I and testing on completion complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement Air Circulator with electric driver steel body AC single Phase 230V of size 300mm with blades, and frame and louvers, and to be deposited to MES store yard complete all as specified and directed.

Supply, laying and testing cable XLPE in replacement Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 4 core.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth, for foundation, laying of cable etc or for shafts, wells cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5m in depth in hard/ dense soil and getting out, complete all as specified and as directed.

Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed by Engr in Charge.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and directed by Engr in Charge.

M&L for Sand cushioning to under ground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, 2009. Note : Punned thickness only will be measured and paid.

Supply and laying of factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-1 flat size 250 mm x 150 mm x 40mm, complete all as specified and directed.

Supply and fix GI Pipe Light grade with all connected accessories of size 40 mm dia complete all as specified and directed.

Please Enable Macros to View BoQ information