Loading…
Loading…
Tender Value
₹1.9 Cr
EMD Value
₹3.8 L
Closing Date
30 Jun 2026, 3:00 pm
Construction of one additional room of 22 free Bungalow and Officer Bungalow at Rail Saurabh Colony Jabalpur under Assistant Divisional Engineer(HQ) Jabalpur sub- division.
DRMW-JBP-90-2026
DRMW-JBP-90-2026
Open
12 Months
Jabalpur, Madhya Pradesh
₹0
₹3.8 L
4 Jun 2026
4 Jun 2026
16 Jun 2026
Rail Saurabh colony Jabalpur under ADEN(HQ)/JBP sub-division.
Item- 1 All Schedule item of DSR 2021
S No. Item No Description of Item Unit Qty Rate Amount
2.0 EARTH WORK
Earth work in excavation by mechanical means
(Hydraulic excavator)/manual means over areas
(exceeding 30 cm in depth, 1.5 m in width as
2.6 well as 10 sqm on plan) including getting out
and disposal of excavated earth lead upto 50 m
and lift upto 1.5 m, as directed by Engineer-in-
2.25 Filling available excavated earth (excluding cum 200 253.95 50790
rock) in trenches, plinth, sides of foundations
etc. in layers not exceeding 20cm in depth,
consolidating each deposited layer by ramming
and watering, lead up to 50 m and lift upto 1.5
4.0 CONCRETE WORK
4.1S CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position cement
concrete of specified grade excluding the cost
of centering and shuttering - All work up to
derived from natural sources : 4 graded stone
aggregate 20 mm nominal size derived from
natural sources)
Providing and fixing at or near ground level
precast cement concrete in kerbs, edgings etc.
as per approved pattern and setting in position
with cement mortar 1:3 (1 Cement : 3 coarse
sand), including the cost of required centering,
shuttering complete.
derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from
natural sources).
5.0 REINFORCED CEMENT CONCRETE
5.1S CAST IN SITU
Providing and laying in position specified grade
of reinforced cement concrete, excluding the
cost of centering, shuttering, finishing and
reinforcement - All work up to plinth level :
derived from natural sources: 3 graded stone
aggregate 20 mm nominal size derived from
natural sources)
5.9S FORM WORK
Centering and shuttering including strutting,
propping etc. and removal of form for
5.9.1 Foundations, footings, bases of columns, etc. Sqm 104 307.95 32026.8
for mass concrete
5.9.3 Suspended floors, roofs, landings, balconies and Sqm 851 766.55 652334.05
access platform
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
5.9.5 Lintels, beams, plinth beams, girders, Sqm 630 608.35 383260.5
bressumers and cantilevers
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 180 804.25 144765
5.22S STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete above plinth
5.22A.6 Thermo-Mechanically Treated bars of grade Fe- Kg 35000 89.65 3137750
6.0 MASONRY WORK
Brick work with common burnt clay F.P.S. (non
6.1 modular) bricks of class designation 7.5 in
foundation and plinth in:
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V
level in all shapes and sizes in :
8.0 CLADDING WORK
Providing and fixing 18 mm thick gang saw cut,
mirror polished, premoulded and prepolished,
machine cut for kitchen platforms, vanity
counters, window sills, facias and similar
locations of required size, approved shade,
colour and texture laid over 20 mm thick base
cement mortar 1:4 (1 cement : 4 coarse sand),
joints treated with white cement, mixed with
matching pigment, epoxy touch ups, including
rubbing, curing, moulding and polishing of
edges to give high gloss finish etc. complete at
Providing edge moulding to 18 mm thick marble
stone counters, Vanities etc., including machine
8.3 polishing to edge to give high gloss finish etc.
complete as per design approved by Engineer-
8.20S STONE WORK DRY CLADDING
8.31 Providing and fixing Ist quality ceramic glazed Sqm 45 1063.45 47855.25
wall tiles conforming to IS: 15622 (thickness to
be specified by the manufacturer), of approved
make, in all colours, shades except burgundy,
bottle green, black of any size as approved by
14 Engineer-in-Charge, in skirting, risers of steps
and dados, over 12 mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) and
jointing with grey cement slurry @ 3.3kg per
sqm, including pointing in white cement mixed
with pigment of matching shade complete.
9.0 WOOD AND P.V.C. WORK
Providing and fixing panelled or panelled and
glazed shutters for doors, windows and
clerestory windows, fixing with butt hinges of
required size with necessary screws, excluding
panelling which will be paid for separately, all
complete as per direction of Engineer-in-charge.
(Note:- Butt hinges and necessary screws shall
be paid separately)
9.7.7 Float glass panes
9.7.7.1 4 mm thick glass pane (weight not less than Sqm 64 1897.1 121414.4
Providing and fixing 25 mm thick shutters for
cup board etc. :
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
Providing and fixing ISI marked flush door
shutters conforming to IS : 2202 (Part I)
decorative type, core of block board
9.20 construction with frame of 1st class hard wood
and well matched teak 3 ply veneering with
vertical grains or cross bands and face veneers
on both faces of shutters.
9.20.2 30 mm thick including ISI marked Stainless Sqm 64 2818.5 180384
Steel butt hinges with necessary screws
ANODISED ALUMINIUM FITTINGS (ALL FITTINGS
SHALL BE ISI MARKED)
Providing and fixing aluminium sliding door
bolts, ISI marked anodised (anodic coating not
9.96 less than grade AC 10 as per IS : 1868),
transparent or dyed to required colour or shade,
with nuts and screws etc. complete :
Providing and fixing aluminium tower bolts, ISI
marked, anodised (anodic coating not less than
9.97 grade AC 10 as per IS : 1868 ) transparent or
dyed to required colour or shade, with
necessary screws etc. complete :
Providing and fixing aluminium handles, ISI
marked, anodised (anodic coating not less than
9.100 grade AC 10 as per IS : 1868) transparent or
dyed to required colour or shade, with
necessary screws etc. complete :
Providing and fixing aluminium hanging floor
door stopper, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS :
1868) transparent or dyed to required colour
and shade, with necessary screws etc.
9.105S GYPSUM BOARD PARTITIONS
9.168 Providing and fixing cupboard shutter with Sqm 400 2563.75 1025500
19mm thick one side decorative and other side
balancing lamination factory pressed BWP
grade marine ply as per IS 710 of approved
brand including 2mm thick PVC edge banding
21 tape with hot glue by edge bending machine
etc. with auto closing spring loaded hinges
(hydraulic type) etc. complete as per direction
of Engineer-in-charge.(Payment of providing
and fixing auto closing hinges shall be paid
9.171 Providing and fixing stainless steel soft closing Each 200 226.75 45350
spring hinges at 0 degree hinges (hydraulic
type) of approved make/brand to cupboard
22 shutters with full threaded steel screws
including making necessary recess in board and
finished etc. complete as per direction of
Engineer-in-charge.
9.172 Providing and fixing stainless steel soft closing Set 50 749.7 37485
heavy type telescopic drawer channels of
23 approved make 500 mm long with screws etc.
complete as per directions of Engineer- in-
10.0 STEEL WORK
10.2 Structural steel work riveted, bolted or welded Kg 2000 111.95 223900
in built up sections, trusses and framed work,
24 including cutting, hoisting, fixing in position and
applying a priming coat of approved steel
primer all complete.
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
Providing and fixing pressed steel door frames
conforming to IS: 4351, manufactured from
commercial mild steel sheet of 1.60 mm
thickness, including hinges, jamb, lock jamb,
bead and if required angle threshold of mild
steel angle of section 50x25 mm, or base ties of
10.14 1.60 mm, pressed mild steel welded or rigidly
fixed together by mechanical means, including
M.S. pressed butt hinges 2.5 mm thick with
mortar guards, lock strike-plate and shock
absorbers as specified and applying a coat of
approved steel primer after pre-treatment of
the surface as directed by Engineer-in-charge:
10.14.2 Profile C
10.14.2.1 Fixing with adjustable lugs with split end tail to Metre 135 471.25 63618.75
11.0 FLOORING
11.16S TILE FLOORING
Chequered terrazo tiles 22 mm thick with
graded marble chips of size up to 6 mm in
floors, jointed with neat cement slurry mixed
11.19 with pigment to match the shade of the tiles,
including rubbing and polishing complete, on 20
mm thick bed of cement mortar 1:4 (1 cement
:4 coarse sand) :
26 11.19.1 Light shade pigment using white cement Sqm 750 1295.2 971400
11.37S CERAMIC GLAZED TILES
11.40 Providing and laying rectified Glazed Ceramic Sqm 72 1225.1 88207.2
floor tiles of size 300x300 mm or more
(thickness to be specified by the manufacturer),
of 1st quality conforming to IS : 15622, of
approved make, in all colours, shades, except
27 White, Ivory, Grey, Fume Red Brown, laid on 20
mm thick Cement Mortar 1:4 (1 Cement : 4
Coarse sand), jointing with grey cement slurry
@ 3.3 kg/ sqm including pointing the joints with
white cement and matching pigments etc.,
11.41S VITRIFIED FLOOR TILES
Providing and laying Vitrified tiles in floor in
different sizes (thickness to be specified by the
manufacturer) with water absorption less than
0.08% and conforming to IS:15622, of approved
brand & manufacturer, in all colours and shade,
laid on 20 mm thick cement mortar 1:4 (1
cement: 4 coarse sand) jointing with grey
11.41A cement slurry @3.3 kg/sqm including grouting
t h e joints with white cement and matching
pigments etc. The tiles must be cut with the
zero chipping diamond cutter only . Laying of
tiles will be done with the notch trowel, plier,
wedge, clips of required thickness, leveling
system and rubber mallet for placing the tiles
gently and easily.
11.41A.2 Glazed vitrified floor tiles polished finish of size
12.0 ROOFING
Providing, fixing and embedding sand cast iron
accessories for rain water pipes in the masonry
12.40 surrounded with 12 mm thick cement mortar of
the same mix, as that of masonry (lead caulking
will be paid for separately):
Providing and fixing on wall face unplasticised
Rigid PVC rain water pipes conforming to IS :
12.41 13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap for
thermal expansion, (i) Single socketed pipes.
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
13.0 FINISHING
13.4S CEMENT PLASTER (IN COARSE SAND)
13.4 12 mm cement plaster of mix :
13.25 Extra for plastering:
13.26 Providing and applying plaster of paris putty of Sqm 7504 214.3 1608107.2
31 2 mm thickness over plastered surface to
prepare the surface even and smooth complete.
13.44S EXTERIOR FINISHING
Finishing with Deluxe Multi surface paint system
13.48 for interiors and exteriors using Primer as per
manufacturers specifications :
13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 90 140.05 12604.5
Paint to give an even shade. Two or more coat
32 applied @ 0.90 ltr/10 sqm over an under coat of
primer applied @ 0.80 ltr/10 sqm of approved
brand and manufacture
Finishing walls with 100% Premium acrylic
emulsion paint having VOC less than 50 gm/litre
and UV resistance as per IS 15489:2004, Alkali
& fungal resistance, dirt resistance exterior
paint of required shade (Company Depot
Tinted) with silicon additives.
13.48A.1 New work (Two or more coats applied @ 1.43 Sqm 7000 154.45 1081150
33 litre/ 10 sqm. Over and including priming coat
of exterior primer applied @ 0.90 litre/10 sqm.
15.0 DISMANTLING AND DEMOLISHING
15.3 Demolishing R.C.C. work manually/ by cum 54 2928.1 158117.4
mechanical means including stacking of steel
34 bars and disposal of unserviceable material
within 50 metres lead as per direction of
Engineer - in- charge.
Demolishing brick work manually/ by
mechanical means including stacking of
15.7 serviceable material and disposal of
unserviceable material within 50 metres lead as
per direction of Engineer-in-charge.
Taking out doors, windows and clerestory
15.13 window shutters (steel or wood) including
stacking within 50 metres lead :
15.60 Disposal of building rubbish / malba / similar cum 800 219.35 175480
unserviceable, dismantled or waste materials
by mechanical means, including loading,
37 transporting, unloading to approved municipal
dumping ground or as approved by Engineer-in-
charge, beyond 50 m initial lead, for all leads
including all lifts involved.
17.0 SANITARY INSTALLATIONS
Providing and fixing white vitreous china
pedestal type water closet (European type W.C.
pan) with seat and lid, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with
manually controlled device (handle lever),
conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making
good the walls and floors wherever required :
17.2.1 W.C. pan with ISI marked white solid plastic Each 5 5540.55 27702.75
17.8 Providing and fixing white vitreous china Each 18 1500.05 27000.9
39 pedestal for wash basin completely recessed at
the back for the reception of pipes and fittings.
18.0 WATER SUPPLY
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
18.7S C.P.V.C. PIPES
Providing and fixing G.I. Pipes complete with
G.I. fittings and clamps, i/c making good the
18.11 walls etc. concealed pipe, including painting
with anti corrosive bitumastic paint, cutting
chases and making good the wall :
Providing and fixing G.I. pipes complete with
18.12 G.I. fittings including trenching and refilling etc.-
Making connection of G.I. distribution branch
with G.I. main of following sizes by providing
and fixing tee, including cutting and threading
the pipe etc. complete :
18.15S BRASS FITTINGS
Providing and fixing brass bib cock of approved
Providing and fixing gun metal gate valve with
C.I. wheel of approved quality (screwed end) :
C.I. SLUICE VALVES/ FIRE HYDRANTS &
Providing and fixing G.I. Union in G.I. pipe
18.46 including cutting and threading the pipe and
making long screws etc. complete (New work) :
18.49S C.P. BRASS FITTINGS
Providing and fixing C.P. brass bib cock of
approved quality conforming to IS:8931 :
Providing and fixing C.P. brass angle valve for
18.53 basin mixer and geyser points of approved
quality conforming to IS:8931
18.59S AIR VALVE & WATER METER (BULK TYPE)
Providing and fixing PTMT Ball cock of approved
quality, colour and make complete with Epoxy
coated aluminium rod with L.P./ H.P.H.D. plastic
not less than 440 gms
19.0 DRAINAGE
19.1S STONE WARE PIPES AND FITTINGS
Providing, laying and jointing glazed stoneware
pipes class SP-1 with stiff mixture of cement
19.1 mortar in the proportion of 1:1 (1 cement : 1
fine sand) including testing of joints etc.
21.0 ALUMINIUM WORK
JABALPUR DIVISION-ENGG/WEST CENTRAL RLY
Providing and fixing aluminium work for doors,
windows, ventilators and partitions with
extruded built up standard tubular sections/
appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS:
1285, fixing with dash fasteners of required dia
and size, including necessary filling up the gaps
at junctions, i.e. at top, bottom and sides with
21.1 required EPDM rubber/ neoprene gasket etc.
Aluminium sections shall be smooth, rust free,
straight, mitred and jointed mechanically
wherever required including cleat angle,
Aluminium snap beading for glazing / paneling,
C.P. brass / stainless steel screws, all complete
as per architectural drawings and the directions
of Engineer-in-charge. (Glazing, paneling and
dash fasteners to be paid for separately) :
21.1.1 For fixed portion
21.1.1.2 Powder coated aluminium (minimum thickness Kg 356 466.3 166002.8
of powder coating 50 micron)
For shutters of doors, windows & ventilators
including providing and fixing hinges/ pivots
and making provision for fixing of fittings
wherever required including the cost of EPDM
rubber / neoprene gasket required (Fittings
shall be paid for separately)
21.1.2.2 Powder coated aluminium (minimum thickness Kg 184 564.8 103923.2
of powder coating 50 micron)
22.0 WATER PROOFING
22.6 Providing and laying water proofing treatment Sqm 1000 585.55 585550
on roofs of slabs by applying cement slurry
mixed with water proofing cement compound
consisting of applying: (a) after surface
preparation, first layer of slurry of cement @
0.488 kg/sqm mixed with water proofing
cement compound @ 0.253 kg/sqm. (b) laying
second layer of Fibre glass cloth when the first
layer is still green. Overlaps of joints of fibre
cloth should not be less than 10 cm. (c) third
layer of 1.5 mm thickness consisting of slurry of
cement @ 1.289 kg/sqm mixed with water
proofing cement compound @ 0.670 kg/sqm
and coarse sand @ 1.289 kg/sqm. This will be
allowed to air cure for 4 hours followed by water
curing for 48 hours. The entire treatment will be
taken upto 30 cm on parapet wall and tucked
into groove in parapet all around. (d) fourth and
final layer of brick tiling with cement mortar
(which will be paid for separately. For the
purpose of measurement the entire treated
surface will be measured.
26.0 NEW TECHNOLOGIES AND MATERIALS
26.28S REPAIR AND REHABILITATION ITEMS
Providing and injecting approved grout in
proportion recommended by the manufacturer
into cracks/honey-comb area of
26.35 concrete/masonry by suitable gun/pump at
required pressure including cutting of nipples
after curing etc. complete as per directions of
Engineer-in-Charge.
26.35.1 Stirrer mixed Acrylic Polymer of approved make Kg 2000 102.85 205700
@ 2% of weight of cement used) modified
Cement slurry made with non shrink compound
in concrete/RCC work
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TDConstof22FeeBungalow.pdf
ATTACHMENT
specialcondition.pdf
ATTACHMENT
AnnexureVIB.pdf
ATTACHMENT
letterforcredit.pdf
ATTACHMENT
RlyBdsletterdated03.6.24JPO-CableCut.pdf
ATTACHMENT
Listofapprovedbrand.pdf
ATTACHMENT
SGCCApril22ACSNo.8to11.pdf
ATTACHMENT
Download all tender documents and submit your bid