ADDITION/ALTREATION AND SPECIAL REPAIRS TO BUILDING NO 36 SHED NEAR TRIBOLOGY GROUP FOR HOUSING CYLINDERICAL MAGNETRON SPUTTERING SYSTEM AT DMRL AND CERTAIN SANCTIONED WORKS AT DMRL HYDERABAD

Amount

Dismantling of AC sheets in roof coverings including ridge pieces all as specified and as directed by Engineer-in-charge.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws as specified.

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges / roof coverings/cladding to wall, fixed with self tapping screws as specified.

Taking down existing unserviceable false ceiling of any description, in any position including channels, sections angles etc, complete all as directed.

S&F Gypsum board false ceiling with GI grid suspended with 2mm dia GI wire at 600mm c/c , holding and level clips, Gypsum board of 12.5mm thick with white paper layer on face side of size 600 x 600 mm as directed and applying two coats of acrylic emulsion over a coat of primer all as directed.

Demolition of cement Concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level). Note : The debries will be disposed off out side the Govt land without any extra cost.

M&L 75 mm thick Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base/floors all as specified .

M&L 50mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in floors

S & F Glass dividing strips, 3mm thick and 38mm width, inserted in position, confirm to design as in PCC flooring

Treating cement concrete or granolithic concrete surfaces with three dressing of sodium silicate solution complete all as specified

S&F rectangular aluminium hollow section, powder coated of approved colour, of size 101.60 mm x44 mmx2 mm thick as in partition including fixing with suitable size of nuts, bolts in fllors and walls by drilling holes, both vertical and horizontal members including provision of sheet glass 5.5 mm thick and 12 mm thick particle board prelaminated on both side with decorative choice lamination, aluminium legs, suncontrol film, aluminium glazing channel, rubber beading, including takingdown old unserviceable wooden/aluminium partition complete all as specified and directed

S&F Powder coated (thickness of powder coating not less than 50 micron) aluminium door shutters,with chowkat, aluminium section weighing 0.55 kg/m including necessary hydrolluic door closer, suncontrol film joining cleats, galzing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc, all accessories including takingdown old UNSV wooden/Aliminium doors complete all as specified and directed

S & F Powder coated aluminium sliding window of standard sections, 2 mm thick (Jindal code No 21516 for bottom track, code No 21517 for top & sides, 21514 for interlock, code No. 21515 for shutter side, top bottom) or equivalent make as approved by GE, powder coated of approved colour incluidng aluminium grill, 4mm thick sheet glass, aluminium handle, bearings, sliding rails, rubber beading, suncontrol film incldung taking down existing unserviceable one, complete all as specified and directed

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, properly rolled on glass panes without any wrinkle including removal of existing unserviceable film on windows/doors complete all as directed by Engr-in-Charge. Make : GARWARE OR EQUIVALENT

S&F Steel rolling shutters gear operated type with bevel gear box and crank handle, with thickness of laths 1.25mm, with out ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as including, complete with and including provision of one shop coat of red-oxide primer, push pull or manual type, fixed in repairs complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/ dense soil.

M&L Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete.

M&L for brick work with flyash bricks sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:4 complete .

M&L for Walling of random rubble masonry regular coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as directed.

M&L 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

M&L for preparation of new plastered unplastered surfaces of walls and applying two coat of cement base paint complete all as specified and as directed

S&F in repairs steel work in tubular trusses, purlins and tubular posts including special shaped washers etc., complete using ERW or induction but welded tubes confirming to IS 1161- 1979 grade St 240 with one shop coat of zinc chromate primer paint at contractor's work shop before fabrication.

S & F in repairs Rolled Mild Steel Plates (plain or Chequered) channels, square cut or notched, forming holes, without any attachment confirming to Fe 410 - W (grade E - 250) quality "A".

S&F Rolled Mild Steel Plate girder or single stanchions confirming to Fe 410 - S built up of one beam or channel section with flanged plates, caps, bases, anchor bolts, angle brackets, splices, cleats and other connections complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils exceeding 1 KM but not exceeding 1.5 KM and depositing where directed.

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of anti corrisive primer.

Taking down cement plaster of any description on stone or brick walls etc including taking out joints, hacking for key, scrubbing down with water etc complete all as per directed.

M&L 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

M&L 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

Supply only integral waterproofing compound complete all as directed by Engineer-in-Charge

M & L for preparation of new plastered wall surfaces and applying two coat of oil bound distemper of any tint including priming plastered surfaces with alkali resistant priming paint

M&L for preparation of new plastered surfaces and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm thick each layer to level the surface and finished smooth with emery paper No.180 followed by emery paper No.320 or 400 and wipe it clean complete all as specified and as directed . Make:- APEX ULTIMA of ASIAN PAINT/ WEATHER COAT SMOOTH(BERGER PAINTS)/ WEATHER SHIELD MAX EXTERIOR ACRYLIC(DULUX)

Taking down chowkhats or frames exc 1.5 sqm but not exc 4.00 sqm without taking off shutters from the frame complete all as directed .

S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

M & L for 35 mm thick factory made 2nd class HW rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated. complete all as specified as directed by Engr-in-charge.

S& F in repair 250mm long alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete.

S&F in 100mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin

S&F aluminium anodised berral tower bolts 150mm long

S&F 150mm extruded aluminium alloy handle fabricated type anodised

Demolition of old existing unserviceable WHB and S&F vitreous china wash hand basin white of size 550 x 400mm flat back excluding taps, waste china and plug but including brackets, CP waste fittings 32mm dia including cutting for and pinning in ends of brackets or erecting stand complete in repair. Make : CERA /NEYCER/ PARRYWARE

S&F in repairs 15mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan head screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as directed.

S& F PVC waste pipe 40 mm dia incl waste coupling of PTMT 40 mm dia for WHB/Urinal

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as directed. Make :- Prayag or equivalent

S&F in repair PVC connection 15mm dia 600mm long with 2 Nos brass check nuts with washer complete all as specified Make :- Prayag or equivalent

S&F 15mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc., including taking down existing old GI tubing complete all as directed.

S&F 20mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc., including taking down existing old GI tubing complete all as directed

S&F in repairs chromium plated, fancy type 15mm dia stop valves /angle cock / concealed stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as directed.

S&F in repairs chromium plated, fancy type 15mm dia bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as directed.

S&F in repairs gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, 20mm bore complete all as directed.

Dismantling existing water tanks of 2000 ltr capacity and removing to store

S&F 2000 ltr Rotational moulded polythelene water storage tanks three layered with hoisted and fixed in position all as specified including PVC float valve 20mm dia complete all as directed.

M&L 75 mm thick cement concrete type C-2 1:3:6 (40 mm graded aggregate) for plinth protection.

S&F venetian blinds (vertical type) of 100mm wide straps with all fittings (to be matched with existing patters) & taking down old venetian blinds complete all as specified and as directed by Engr-in-Charge. Make : MAC/VISTA/MARC/AMAR

M&L for Complete removal of existing treatment and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wall putty to make surfaces smooth.

M&L for complete removal of existing treatment from external surfaces of walls/ ceiling, washing with water and applying two coats of weather proof antifungal exterior paint as per manufacturers instructions over a coat of true care exterior wall primer over two coats of external birla putty 1.5mm thick each layer each to level the surface and finished smooth with emery paper No.180 followed by emery paper No.320 or 400 and wipe it clean complete all as specified and as directed by Eng-in-charge. Make:- APEX ULTIMA of ASIAN PAINT/ WEATHER COAT SMOOTH(BERGER PAINTS)/ WEATHER SHIELD MAX EXTERIOR ACRYLIC(DULUX)

Surface excavation n exc 30cm deep and averaging 15 cm deep and getting out hard/dence soil

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

M&L cement concrete type D-2, 1:3:6 (40 mm graded aggregate) as in sub base, mass concrete complete

S&F machine pressed precast concrete interlocking paver block any shape and size with gray cement and pigment (approved by GE) confirming to IS 15658-2006 of 80 mm thick, M-35 grade for laying over sand cushion bed 40mm thick including watering and consideration with mechanical vibrator complete all as directed.

M&L cement concrete type B-1, 1:2:4 (20mm graded aggregate ) 100mm thick as in paths/ hardstanding finishing cement concrete surface even and smooth without using extra cement includng spike rolling to surfaces or making impressions of expanded metal whilst the concrete is green complete.

Forming 12mm thick expansion joints for 100mm thick concrete slabs filled with pre- formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'A' complete

M & L for reinforced cement concrete (Nominal mix ) type B-1, 1:2:4 (20 mm graded aggregate) in foundation includng rafts, footings, foundation beams, plinth beams, bases for columns etc , basement slabs under reamed piles and mass concrete complete

M & L for rough finish flat surface of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter

M & L mild steel bars TMT 10 mm dia and over, cut to length,bent to shape required, including cranking, bending spirally for hooping for coh, .nns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified .

All as per item No.66 above but 5 mm over upto and including 10 mm dia in stirrups, spacers and binders.

S&F expanded metal not exc 4 Kg weight per square metre cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples complete to steel members complete

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc incluidng stainless steel square mesh welding , grinding buffing, polishing and making curvature ( where ever required) and fitting the same with necessary stainless steel nuts and bolts complete incluidng fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size on the top of floor or the side of waist slab with suitable arrangement complete. Make: JINDAL 304 grade

S&F mild steel screw bolts diameter of neck 11 to 15mm ( machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends to be fitted with washers and one hexagonal or square nut exc 5cm but not exc 10cm long

M&L for preparation of new plastered surface of wall and applying three coats of white wash to wall complete

Taking down carefully of any type point wiring light fans socket or power complete fitting such as switch ceiling roses, pendent, regulator, sockets etc removing material and making good disturb surface of wall floor etc complete all as directed.

M&L for wiring point wiring complete with 1.5 Sqmm PVC insulated FRLS unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20 mm dia PVC conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc. and Terminated to sunken box of modular type including white cover plates suitable for fixing switches, sockets etc including 1.5 Sqmm PVC insulated FRLS Copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for the following:-

One light point controlled by one way modular switch 6 Amps

One ceiling fan point /Exh fan point controlled by one 5 Amps one way switch and regulator

One 3 pin 5 Amps switch socket outlet point on independent board

One 3 pin socket outlet 5 Amps on the same board with other switches.

M&L for point wiring complete with 2.5 Sqmm PVC insulated FRLS unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20 mm dia pvc conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc on Ceiling and Terminated to sunken box of modular type including white cover plates suitable for fixing switches, sockets etc including 2.5 Sqmm PVC insulated FRLS Copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for 3 in one 3 pin socket outlet. 15 amps,independent:- Make:- Conductor: Finolex/Finecab/Polycab/Plaza PVC Conduit: Finolex/Tirupati/Supreme/Prince/Avon plast/ Plaza

S&F modular switch one way 6 amps 1 module

S&F modular switch one way 16 amps 1 module

S&F modular fan step type regulator two module

S&F modular socket out let 6 Amps 230 volts AC 3 pin multipurpose type complete all as directed.

S&F modular socket out let 6/16 Amps multipurpose complete all as directed by Engineer-in-Charge.

S&F ceiling rose two to three terminal surface backallite type AC 50Hz 230 volts complete

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC, 5700K industrial luminaries recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Taking down Ceiling fan/Exhaust fan of any make and sweep dismantling, cleaning greasing/ overhauling, adjustment of down rod including replacement of rubber , bolt & nuts etc including new painting in two coats with existing colour and refixing in existing position with new cable wire connection between ceiling rose to fan connector complete all as directed by Engr-in-charge.

S&F MCB single pole 5 Amp to 32 Amps complete all as directed by Engr-in-charge.

S&F MCB SPN 240 Volts 40 Amps complete

S&F MCB TPN 415 Volts 40to 100 Amps complete

S&F sheet metal enclosure MCB DB TPN double door type AC 415V 4 way with 200 Amps rated bus bar, including taking down old one complete and making good of distructed surfaces

S&F sheet metal enclosure MCB DB SPN double door type AC 240 V 8 way with 200 Amps rated bus bar, including taking down old one complete and making good of distructed surfaces

M&L for sub main wiring complete with 2 runs of 6.0 Sqmm PVC insulated FRLS heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including stove enamelled steel conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 6.0 Sqmm PVC insulated FRLS copper cable for earth continuity conductor and connecting to earth dolly including taking down old u/s one complete

M&L for sub main wiring complete with 2 runs of 04 Sqmm PVC insulated FRLS heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including stove enamelled steel conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 04 Sqmm PVC insulated FRLS copper cable for earth continuity conductor and connecting to earth dolly including taking down old u/s one complete

M&L Chemical earthing with copper earth plate 90x60cmx5mm buried directly in ground vertically to a depth of not less than 2.25mtr below ground level than 1.5mtr below ground level connected to & copper earth strip 50x6mm by means of bolts washers etc and using required qty of chemical power fill and power set compound from bottom to top edge of the copper earth plate complete (as per IEEE80 and IEC 62561) made out of copper strip will be protected by galvanized iron pipe medium grade 80mm bore up to main distribution board/main switch including necessary excavation and earth work PCC 1:3:6 type CI (using 20mm graded stone aggregate) RCC cover 1:2:4 type B1 including necessary reinforcement etc complete all as shown electric plate No.3 of MES Sch Part-I.

M&L Earthing complete with GI earth plate electrode 600x600x6mm buried directly in ground vertically to a depth of not less than 2.25mtr below ground level connected to GI strip 25x4 dia by means of bolts washers etc made out of strip will be protected by galvanized iron pipe medium grade 15mm bore up to main distribution board/main switch including necessary excavation and earth work PCC 1:3:6 type CI (using 20mm graded stone aggregate) RCC cover 1:2:4 type B1 including necessary reinforcement etc complete all as shown electric plate No.3 of MES Sch Part-I.,

M&L Earthing continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25x4mm dia galvanised iron all as directed

M&L Earthing continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm dia Copper Strip complete all as directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver in existing brick wall by making hole of suitable size and making good the disturbed surface and match the color with existing color of wall complete all as specified and as directed.

Supply & fix Air Circulator fans 230 volts single phase oscillating 600 mm sweep, RPM 1440, Air Delivery : 250CMM to be fix on wall complete all as specified and directed. Make: ALMONARD/ CROMPTON GREAVES/ HAVELLS

Supply and spreading of natural, clean, dry, river sand in trenches for cable protection / transformer yard/ two pole structure yard complete all as directed. Note:- Punned thickness only shall be measured for payment purpose.

M&L for laying of common burnt bricks, sub class 'B', old size 230 x 115 x 75 mm in trenches for cable protection complete all as directed.

Cutting the road/hard standing to a size not exceeding 30cm in width not exceeding 75cm in depth for laying /removal of LT UG cable /protection including making good so as to match with existing finishing with PCC (1:4:8) type D2 (using 40mm grade stone aggregate) for 100mm thick on top including fair finishing.

Supply and lay GI tubing 80mm dia, light grade for cable protection at road crossing/on poles and tubing sealed at both ends after laying the cables complete all as specified and directed by Engineer - in - Charge.

Supply, laying, testing and commissioning in trenches/ ducts, fixed on walls/panels of XLPE cable, 1100 volts grade, PVC insulated, unsheathed armoured with aluminum conductor cable complete including lugs of requied sizes all as directed for the following nominal cross sectional areas of cables 240 Sqmm 3.5 core complete all as specified and directed

Design, Supply, erect, Testing & Commissioning of Automatic Rolling Shutter motor (motorization including motor & mechanisation eqpt) for existing mechanical rolling shutter (any size upto 2000Kgs) in one single unit with 2 Ton lifting capacity by replacing the rolling spring assembly with new cylindrical type rolling assembly and chain crank in absence of power complete with ball bearing and springs minimum cost of maintenance with single phase motor 750W , Speed upto 6.2 RPM , output Torque 1102N.M contorlled by push button startor with all connection copper wiring complete, limit switches, control wiring with copper conductor including necessary dismantling/refixing of shutter, addition/alteration civil works any required on site complete all as specified and directed

M&L for disconnecting , dismantling of existing cantilver type elecric operated crane of any capacity by mechanical/manpower means with all laid down safety measure and shifted the entire dismanteld crane and its parts to E/M store in DMRL area only by making detail inventory all parts of crane and deposit the same in E/M store yard all as specified and directed.

Supply and install hi wall split unit indoor & outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of Capacity 2.0TR, Invertor type, minimum 3 star rating working on non CFC refrigerant complete all as specified and directed. Make: BLUE STAR/HITACHI/ VOLTAS

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA.

M&L Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps, 240V Cap\cacity complete all as specified and directed

M&L for sub main wiring for AC (from DB to AC metal clad box)complete with 2 runs of 4 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including stove enamelled steel conduit concealed on walls/fixing it with existing iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 4 Sqmm insulated copper cable for earth continuity conductor and connecting to earth dolly and taking down old u/s one complete all as directed by Eng-in-charge

M&L for wiring point wiring complete with 1.5 Sqmm FRLS PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20 mm dia pvc conduit concealed on walls/fixing it with iron canopoy of shed with and including suitable size MS clamps etc. and Terminated to surface mounting PVC box with and including suitable size MS clamps to fix these boxes to column Poles of shed modular type including 1.5 Sqmm FRLS PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for the following:-

One light point controlled by one way modular switch 6 Amps

One 3 pin 5 Amps switch socket outlet point on independent board

One 3 pin socket outlet 5 Amps on the same board with other switches.

M&L for point wiring complete with 2.5 Sqmm FRLS PVC insulated unsheathed single core multi standard copper conductor 1100 V grade drawn through in and including 20 mm dia spvcconduit concealed on walls/fixing it with iron canopoy of shed with and including suitable size MS clamps etc on Ceiling and Terminated to surface mounting PVC box with and including suitable size MS clamps to fix these boxes to column Poles of shed modular type including white cover plates suitable for fixing switches, sockets etc including 2.5 Sqmm FRLS PVC insulated Copper conductor cable as earth continuity conductor and connecting to common earth dolly and taking down old one complete all as specified and directed for 3 One 3 pin socket outlet. 15 amps,independent:- Make:- Conductor: Finolex/Finecab/Polycab/Plaza PVC Conduit: Finolex/Tirupati/Supreme/Prince/Avon plast/ Plaza

Supply and fixing LED security light fitting 35 Watt 230 V AC, high performance IP 66 Protection, 5700K color temp, made up of die cast aluminium housing with high power LED as lightening source and lens embedded PC lens having complete and fixing with GI bracket made out of 40mm bore GI light grade 1.5 mtr length bend to shape and fixed to pole /wall with inecessary MS clamp and accessories complete all as specified and directed .

Supply and fixing LED lights fitting 1x 18/20W, 230V,Surface/wall e AC decorative box type with driver, Lumen efficiency of 6500K in CDL varient , 2.5 KV voltage surge protection , PF > 0.9, made out of powder coatted extruded aluminium housng elgent endcap holder including LED tube light connecting up with three core flexiblecopper conductor cable of suitable size from ceiling rose complete

S&F sheet metal enclosure MCB DB SPN double door type AC 240 V 4 way with 200 Amps rated bus bar, complete

M&L for sub main wiring complete with 2 runs of 04 Sqmm FRLS PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through in and including PVC conduit concealed on walls/fixing it with iron canopoy of shed with and including suitable size MS clamps etc and connecting terminal ends to meters and DB's including provision of 1 run of 04 Sqmm FRLS PVC insulated copper cable for earth continuity conductor and connecting to earth dolly and taking down old u/s one complete

Earthing complete with GI earth plate electrode 600x600x6mm buried directly in ground vertically to a depth of not less than 2.25mtr below ground level than 1.5mtr below ground level connected to GI wire 4.0 dia by means of bolts washers etc made out of strip wire will be protected by galvanized iron pipe medium grade 15mm bore up to main distribution board/main switch including necessary excavation and earth work PCC 1:3:6 type CI (using 20mm graded stone aggregate) RCC cover 1:2:4 type B1 including necessary reinforcement etc complete all as show electric plate No.3 of MES Such Part-I.,

Supply and lay XLPE indulated, screened, PVC bedded, electirc power cable( heavy duty) ,galvanized steel strip or wire armoured, 1100volts grade with stranded aluminium conductor of size 10.0 sqm 2 core complete

Supply and lay GI tubing 50mm dia, light grade for cable protection at road crossing/on poles and tubing sealed at bith ends after laying the cables complete all as specified and directed by Engineer - in - Charge.

M&L cutting to existing steel tubing for alterations upto 50 mm GI tubing

S&F 50 mm bore dia steel water tubing medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors incl taking down old pipes andcutting/chasing in wall/floor complete all as specified

S&F 40 mm bore dia steel water tubing medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors incl taking down old pipes andcutting/chasing in wall/floor complete all as specified

S&F 25 mm bore dia steel water tubing medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors incl taking down old pipes andcutting/chasing in wall/floor complete all as specified

S&F Cast copper alloy Stop Valve, 50 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

S&F Cast copper alloy Stop Valve, 25 mm size screwed down, high pressure, with butterfly handle screwed both end for iorn pipe.

M/S AKSHATHA ENTERPRISES

Bismi Engineering

SHAH ENTERPRISES

M/S C MALLIAH & SONS

CHAVA CONSTRUCTIONS AND ELECTRICAL PROJECTS