28/EDC(G)/2025-26

Amount

All these below items/materials from S.N. 1.01 to 1.36 shall be given by the contractor on his own cost as per estimate/Resspo Norms.

Holding clamp for TPMO, fuse set, Top, T-off, dropper etc.

V-Type X-arm holding clamp

F-Bracket with clamp

Nut and bolt off. Size with washer

LT Clamp for PCC/STP

LT shackle Insulator

Stay Insulator

S/S base angle for 11 KV

S/S base angle for 33 KV

Danger Board

Distribution box with clamp of Three phase

Distribution box with clamp of single phase

I hook with clamp for PCC/STP

Dead end clamp for PCC/STP

Suspension clamp for PCC/STP

Stay clamp for PCC/STP

Top Channel for 11 KV

Top Channel for 33 KV

T-off Channel for 11 KV

T-off Channel for 33 KV

Dropper Channel for 11 KV

Dropper Channel for 33 KV

TPMO set for 11 KV with complete fitting

TPMO set for 33 KV with complete fitting

D.O. Fuse set for 11 KV with complete fitting

D.O. Fuse set for 33 KV with complete fitting

Fuse set installed in SMC Box

Tailless unit with lead as estimates requirement

X basing angle

Stone Pad

Earthing Rod

Straight through for 11 KV of different size

Straight through for 33 KV of different size

11 KV CJ kit of different size

33 KV CJ kit of different size

Guarding angle with clamp

Loading, Unloading and safe cartage of the following materials (S.N. 2.01 to 2.15) from Electricity Store Centre, Gonda to the work site/dump site (Within geographical area of EDC, Gonda)

25/63/100 KVA T/F

250/400 KVA T/F

PVC Cable

PCC/STP Pole

ACSR Weasal Cond.

AB Cable of different size

XLPE Cable of different size

GI wire 10 swg

Barbed wire

33/11 kv disk insulator with Complete fitting

33/11 KV pin insulator with Pin with Complete fitting

Stay set complete

Pilfer Cubical unit of different capacity

11 KV VCB of different capacity

other line material

Erection of single PCC/ST Poles for 11 KV/L.T. line alongwith fitting of all accessories on pole.

Erection of sectional double pole sectional PCC/STP pole alongwith fitting of all accessories.

Earthing of pole with complete fitting

Erection and Grouting of stay sets alongwith complete fittings. Cement, Sand & Brick ballast provided by the contractor at his own cost.

Grouting of Poles with 1:4:8 CC ratio of cement, sand & brick ballast, backfilling of pits with mud completely.All required materials provided by the contractor at his own cost.

Construction of 11/0.4 KV S/S for following capacity of T/F with mounting and fitting of T/F on plinth/double pole with proper fitting of all acessories and connecting with all circuit including earthing of T/F fitting with all accessories.

25/63/100 KVA T/F

250/400 KVA T/F

Laying, Stringing & Sagging of ABC Cable up to proper sag of different size as per estimate/resspo norms

Laying, stringing, sagging & binding of conductors of 11 KV in 3 phase, 3 wire line with jumpering (where as required)

Laying, stringing, sagging & binding of XLPE Cable of different size with complete fitting by digging of trench/drill method as per estimate/RESSPO norms.

Complete jumpering with help of G.I. pipe as per RSSPO norms. G.I. Pipe and other required material shall be supplied by the contractor on his own cost.

Bore type Earthing and lowering "B" class G.I. Pipe (Gindal) of 50mm dia from ground upto water level not less than 20mtr. As per standard /Estimate/Resspo Norms. (All the required material shall be given by contractor on his own cost.)

Chemical earthing of Pole/Transformer as per Estimate/Resspo Norms(all the material shall be provided by contractor on his own cost.)

Construction of T/F plinth of size 2x2x1.5 mtr on a padding 0.25M deep in ground 1:5:10 cement sand and brick ballast on the top of padding brick work Ist class brick of 0.95 mtr. Height and 0.35 mtr wall will be constructed. Rest wall should be 0.23 mtr thick. brick work in ratio 1:4 cement and cores sand in the hollow portion the sand should be filled from the ground level up to 15 centimeter below from the top of wall, cement, sand and brick ballasts should be filled up to 15 centimeer. Two no. of channel 100x50 in length 1500mm will be grouted. 0.35 cm RCC will be done with cores sand, cement and stone ballast in the ratio of 1:2:4. The T/F's plinth should be plastered on all sides 12mm thick in ration 1:6 by cement and cores sand. (All the required material shall be given the contractor on his own cost.)

Fabrication, installation and grouting of M.S. frame as well as fixing Tailless unit as per requirement (2/3/4 nos.) for Distribution Transformer LT side of capacity 160/250/400/630/1000 KVA. The size of M.S. frame is of following dimension- MS Angle of 35X5 mm., Height 8 feet, grouting 01 feet with wire mesh fencing as per drawing/sample. Aluminium patia 04 Number-dimension 10X50X700 mm. With properly paint with Red Oxide paint and Yellow colour paint as well as required, Lug, copper L Piece, fuse wire and nut & bolt. (All the material required for above work shall be provided by the Contractor on his own cost)

Fencing of Transformer as per estimate requirement as per RESSPO norms.

Cutting of tree branches for cleaning route of 11 KV/LT line at the work site (25 mtr.= 1 Job)

Carrage of scrap/conductor from site to store

Guarding of line

Installation/Errection/Laying/stringing of the following items with complete fitting as per estimate/resspo norms.

Danger Board with complete fitting

Distribution box with clamp of Three phase

Distribution box with clamp of single phase

TPMO set for 11 KV with complete fitting

TPMO set for 33 KV with complete fitting

D.O. Fuse set for 11 KV with complete fitting

D.O. Fuse set for 33 KV with complete fitting

Fuse set installed in SMC Box

PVC Cable

11 KV VCB of different capacity

Pilfer Cubical unit of different capacity with complete fitting

M/s S S Associates (BID ID -5289386)

Hindustan Electric Work (BID ID -5289817)