MGU

Providing post construction anti termite treatment by drilling 1/2 inch dia., holes at the edges of wall floor junction and pouring anti termite chemical (Imidacloprid 30.5 SC, 10.5 ml for 5 Liters of water as per IS 16131.) with a hand operated pressure pump until refusal or to a maximum of one liter per hole. Holes shall be sealed with cement motor after treatment and providing spraying and injecting termiticides for treating and applying to doors, windows, frames, removing, crusting treating in Treatment along outside of foundations (i.e., Soil in contact with external walls around the building and Concrete or Masonry apron around the building), Treatment of soil under floors - Inside Building, Treatment to voids in masonry, Treatment at points of contact of woodwork, Treatment of Wood Work, Treatment of Electrical Fixtures, as directed in IS 6313 Part 3 2013 with preventive chemicals duly taking precautions for health hazards and safety measures for the occupants including all costs, conveyances of all materials and labour charges etc for finished item of work to the satisfaction of the Engineer-in-Charge. The plinth area of the building each floor shall be taken for the purpose of payment.

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For Columns in First floor

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For Roof Beams

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For Roof Slab 150 mm thick

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For WAIST SLAB 150MM THICK

Supply and placing of Design Mix Concrete M 25 grade corresponding to IS 456 with minimum cement content of 380 kgs per 1 cum of concrete using Batching Plant of capacity 50 cum per hour and transporting concrete to site by Transit mixer of 2cum capacity and pumping concrete; using pump and with 20mm size graded machine crushed hard Granite metal (coarse aggregate)(consisting of nominal size metal 60% of 20mm, 15% of 13.20/12.50mm, 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing and cost of overheads & contractors profit etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402). RCC M25 grade for Steps

Supply and placing of Design Mix Concrete M20 grade corresponding to IS 456 with minimum cement content of 350 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard Granite metal (coarse aggregate)(consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing and cost of overheads & contractors profit etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) FOR , LINTELS

Supply and placing of the Design Mix Concrete M 20 grade corresponding to IS 456 with minimum cement content of 350 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard Granite metal (coarse aggregate) ( consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., for 60 cm wide sun-shades 7.5cm thick at fixed end and 5cm thick at free end with an average thickness of 6.25cm including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting concrete, laying concrete, curing, cost of overheads & contractors profit complete etc., but excluding cost of steel and its fabrication charges for finished item of work for sunshades (APSS No. 402, 403 & 903) & 903)

Solid Fly-ash Block masonry 225 mm thick for panel walls in super structure, parapet walls with cement mortar (1:6) prop (Cement:sand) using solid fly-ash blocks of size 290 x 225 x 140 mm from approved source having minimum crushing strength of 5 N/sq.mm. including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), bricks, water etc., to site, excluding seigniorage on all materials but including all incidental and operational, labour charges like mixing cement mortar, scaffolding charges (with MS Jack Prop Cup lock Pipe Scaffolds, constructing masonry, lift charges, curing overheads & contractors profit etc., complete for finished item of work as per SS 504. for:-Fly Ash Block Masonry in CM 1:6 (290x225x140)

Reinforced Solid Fly-ash Block Masonry for partition walls (100 mm thick) for panel walls in super structure, parapet walls with cement mortar (1:6) prop (Cement:sand) using solid fly-ash blocks of size 290 x 100 x 140 mm for manufacturing of flyash solid blocks from approved source having minimum crushing strength of 5 N/sq.mm. and placing 2 nos of 6mm M.S plain rods in every third layer with free ends of the reinforcement pegged into mortar joints of main brick walls wherever applicable including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), bricks, water etc., to site, excluding cost of seigniorage charges on all materials, but including cost of scaffolding charges (with MS Jack Prop Cup lock Pipe Scaffolds) and all operational, incidental , labour charges like mixing cement mortar, lift charges, curing, overheads & contractors profit etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 509 & 501)

Ornamental ceiling plastering 12mm thick using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8 mm thick in CM(1:5) and top coat of 4mm thick in CM(1:3) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work .(SS 901,903 & 904)

Plastering 12mm thick in two coats using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials, cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Plastering 12mm thick in two coats using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials, cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Providing and applying synthetic plaster putty or equivalent putty of white cement or polymer or cement based such as birla wall care putty or equivalent of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying putty paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work for internal walls - :-Internal Colouring - Providing Putty.

Providing and applying synthetic plaster putty or equivalent putty of white cement or polymer or cement based such as birla wall care putty or equivalent of average 2 to 3 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying putty paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads and contractors profit for finished item of work for external walls - including cost of access scaffolding(with MS Jack Prop Cup lock Pipe Scaffolds) for:-External Putty

Painting to new walls with 2 coats of acrylic emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 30 grams/ litre of approved brand and shade over a base coat of approved water based Cement Primer of Interior Grade- 1 making 3 coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads & contractors profit for finished item of work as per SS 912 for Internal walls - Plastic emulsion paint - 2 Coats + 1 coat primer.

Providing and applying Exterior grade texture ready mixed paint with sand texture added sand particles Acrylic copolymers and mineral compounds, bactericides and various additives having VOC (Volatile Organic Compound) content less than 30 grams/ Lit or equivalent of average 2 to 3 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying texture paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads and contractors profit for finished item of work for external walls - including cost of access scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) for:-External Colouring - Providing / Texture to External walls.

Painting to new walls with 2 coats of acrylic emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 30 grams/ litre of approved brand and shade over a base coat of approved water based Cement Primer of Exterior Grade- 2 making 3 coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads & contractors profit for finished item of work as per SS 912 for external walls for:-External Colouring - Plastic emulsion paint - 3 Coats.

Painting to new wood work with luppam finish to give even & smooth surface and painting two coats with ready mixed Synthetic Enamel in all shades Grade - I / Polyurethane full gloss Enamel (IS - 13213) paints having VOC (Volatile Organic Compound) content less than 30 grams/ Lit over wood primer coat, including cost and conveyance of all materials to site, all labour charges , including sand paper on lappam coats for neat even and glossy surface, including cost of overheads & contractors profit, etc. complete for finished item of work as directed by Engineer-in-charge during exection - for all floors.

Painting to new iron works with 2 coats of Synthetic Enamel paints in all shades Grade - I having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade over 1 coat of Red Oxide Primer Paint for iron works of Grade -1 of approved brand to give an even shade after thoroughly cleaning and sand papering the surface to remove all dirt and remains, including cost and conveyance of all materials to work site including cost of primer coat and all operational, incidental, labour charges etc. complete etc., complete including cost of overheads & contractors profit (APSS No.1200, 1207 & 1211) in all floors.

Flooring with high polished granite 16 to 18 mm thick up to 8'-00 (2.43 M) of regular colours including black set over a base coat of CM (1:8) prop, (fine aggregate to be used as (50% sand + 50% manufactured sand)). 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of granite to full depth including cost and conveyance of all materials like cement, sand, water, granite, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying granite to required slope as directed by the Engineer- in-charge, cost of overheads & contractors profit etc., complete for finished item of work . (APSS No.701 & 707)

Flooring with high polished granite 16 to 18 mm thick up to 8'-00 (2.43 M) of regular colours including black set over a base coat of CM (1:8) prop, (fine aggregate to be used as (50% sand + 50% manufactured sand)). 20mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of granite to full depth including cost and conveyance of all materials like cement, sand, water, granite, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying granite to required slope as directed by the Engineer- in-charge, cost of overheads & contractors profit etc., complete for finished item of work . (APSS No.701 & 707) Treads 0.30m wide

Providing 16 to 18mm thick high polished granite stone slabs of regular colours including balck, with borders and design as per the pattern approved by the Engineer-in-Charge of length not less than 2.43 mts set over base coat of cement mortar (1:5) , 12mm thick using screened sand over CC bed already laid or RCC roof slab including neat grey cement slurry of honey like consistency spread @ 3.3 Kg per sqm and jointed neatly with white cement paste mixed with pigment of matching shade to full depth including cost and conveyance of all materials like cement , sand , water , granite slabs etc., to work site and all operational, incidental labour & lift charges, half rounding the edges of treads , polishing charges and cost of base coat and overheads & contractors profit, complete for finished item of work for Risers (S.S.701 & special)

Flooring with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 40mm thick over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) excluding cost of seigniorage charges on all materials, but including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc., including overheads & contractors profit complete for finished item of work. (APSS No.701 & 707) - TBSC-C.II-03

Skirting with Nano polished /stain free soluble salt porcelain vitrified tiles screen printed of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with length equal to flooring stones and matching the flooring joint lines and set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth, including cost and conveyane of all materials like tiles, cement, sand and water etc., to site excluding cost of seigniorage charges but including overheads and contractor profit complete for finished item of work.(APSS No.701 &707) The skirting should flush online with plastering. - TBSC-C.II-03

Flooring with full body heavy duty industrial variety porcelain vitrified tile of size 600 x 600 mm and thickness between 10 - 12 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 40mm thick over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) excluding cost of seigniorage charges on all materials, but including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc., including overheads & contractors profit complete for finished item of work. (APSS No.701 & 707) - TBSC-C.II-16

Skirting with full body heavy duty industrial variety porcelain vitrified tile of size 600 x 600 mm and thickness between 10 - 12 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with length equal to flooring stones and matching the flooring joint lines and set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to match the shade of tiles to full depth, including cost and conveyane of all materials like tiles, cement, sand and water etc., to site excluding cost of seigniorage charges but including overheads and contractor profit complete for finished item of work.(APSS No.701 &707) The skirting should flush online with plastering. - TBSC-C.II-16

Flooring with Non-skid red or white full body Ceramic floor tiles of size 300 x 300 mm and thickness between 7-8 mm 1st quality conforming to IS:15622 - 2017, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 12mm thick including neat cement slurry of honey like consistancy spread at the rate of 3.3kg per sqm and filling the joints with white cement mixed with pigment of matching shade to match the shade of tiles over a bed of C.C. or R.C.C. slab, including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), water, ceramic tiles, white cement etc., to site (excluding cost of C.C. bed), cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer-in-charge curing etc., complete and cost of overheads and contractor profit for finished item of work. (APSS No.707 & 701)

Dadooing to walls with any color glazed tiles 1st. quality of any size of brand as approved by Engineer - in - charge and set over a base coat of CM (1:5), 12mm thick and neat cement paste at the rate of 3.3 Kg/Sqmt. and jointed with white cement paste mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, etc. to site, sales and other taxes on all materials, C921 such as mixing of cement mortar, laying in position, curing, lift charges etc., complete but excluding seigniorage charges for finished item of work (APSS No.701 & 707) in All Floors

Providing impervious coat to exposed RCC roof slab surfaces to required slopes with CM (1:3) prop. using screened sand 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by Engineer-in-charge at 1 Kg per one bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), water proofing compound, water etc., to site, all operational, incidental, and labour charges for mixing mortar, laying, lift charges, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., and overheads & contractors profit complete for finished item of work. (APSS No. 901 & 903).

Supplying and fixing of single / double shutter doors with Mild Steel Hallow single rebate general purpose door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile-B of size 105 x 60 mm conforming to IS 4351 - 2003 including pretreatment, phosphating with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for Flush door shutters with solid bond wood block board type with commercial ply on both faces.: 35 mm thick conforming to IS:2202 as per drawing including including cost of Stainless Steel fixtures of 1 No tower bolts of 250x10mm dia, 1 No. Aldrops - 300 mm long and 2 Nos. handles of 150 mm size, 1 No. door stopper, 1 Nos. rubber bushes including fixing the fixtures to door with required no. of screws, bolts and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame etc., including overheads and contractor profit etc., complete for finished item of work

Supplying and fixing of single / double shutter doors with Mild Steel Hallow single rebate general purpose door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile-B of size 105 x 60 mm conforming to IS 4351 - 2003 including pretreatment, phosphating with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for Flush door shutters with solid bond wood block board type with commercial ply on both faces.: 35 mm thick conforming to IS:2202 as per drawing including including cost of Stainless Steel fixtures of 1 No tower bolts of 250x10mm dia, 1 No. Aldrops - 300 mm long and 2 Nos. handles of 150 mm size, 1 No. door stopper, 1 Nos. rubber bushes including fixing the fixtures to door with required no. of screws, bolts and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame etc., including overheads and contractor profit etc., complete for finished item of work Door size - 1.20 x 2.10

Supplying and fixing of single / double shutter doors with Mild Steel Hallow single rebate general purpose door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile-B of size 105 x 60 mm conforming to IS 4351 - 2003 including pretreatment, phosphating with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for Flush door shutters with solid bond wood block board type with commercial ply on both faces.: 35 mm thick conforming to IS:2202 as per drawing including including cost of Stainless Steel fixtures of 1 No tower bolts of 250x10mm dia, 1 No. Aldrops - 300 mm long and 2 Nos. handles of 150 mm size, 1 No. door stopper, 1 Nos. rubber bushes including fixing the fixtures to door with required no. of screws, bolts and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame etc., including overheads and contractor profit etc., complete for finished item of work Door size - 1.00 x 2.10

Providing of Factory made prelaminated FPVC (Foamed Polyvinyl Chloride) Door frame of the size 105x40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6 Nos. of 50mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 no's to be provided for each vertical member, GI stiffeners of ("U" channel of size 29x9x1mm, 150mm long) -3 no's at hinge point, Frame reinforcement of("U" GI channel of size 46x22x.06mm), Bottom tie rod of ("U" GI channel size of 15x15x1mm) etc. complete as per manufacturers specification for finished item of work. Maximum door frame size : 980 x 2070 including providing of 35mm thick Factory made Prelaminated ABS (Acrylonitrile Butadiene Styrene) Door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32x 32mm - 2 nos. for vertical made out of LVL (Laminated Veneer Lumber), core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with prelaminated ABS sheet thickness of 1.5mm . PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos. for each shutter and ISI make S.S round lock completes for finished item of work. Maximum shutter size of : 910 x 2030 mm, including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site, overheads and contractor's profit, etc complete for finished item of work.

Supplying and fixing of Unplasticized Poly Vinyl Chloride (UPVC) 3 track sliding windows with mesh shutter – (2-glass shutters and 1-mesh shutter) duly manufactured using UPVC reinforced profiles (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin) of (94 mm x 45 mm)/(80 mm x 52mm) x 2.20 mm for outer frames, (58 mm x 39 mm)/(54 mm x 38 mm) x 2.20 mm for sliding shutter frames capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.0/1.2 mm prefabricated & welded through fusion welding. The window sash shall be fitted with 5 mm thick clear float glass of reputed make and mesh shutter frame shall be (42 mm x 25mm)/(52 mm x 21.5 mm) x 2.0 mm fitted with Vinyl Coated Fibre mesh- on rollers/ pulley duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC. System shall have single point locking with Touch Lock and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories,labour charges for transportation, erection at site complete for finished item of work. including all incidental, labour charges, overheads and contractor's profit, etc. complete for finished item of work.

Providing, supplying & fixing of Fixed Louvered Ventilator made out of multi chambered uPVC sections with Glazing bead shall be co-extruded with Grey colour soft PVC. having isolated drainage and reinforced with Galvanized Iron profiles throughout the window. The outer frame having an overall size of 60 mm x 55 mm x 2.40 with reinforcement of 1 mm thickness and Mullion with overall size of 74 mm x 60 mm x 2.40mm with reinforcement of 1 mm thickness. (Composition of profile shall consists a minimum of 5.5 PHR of TiO2 and not more than 12 PHR of CaCo3 for every 100 parts of PVC resin).Ventilator shall be provided with 4.5 mm Pin Head glass, standard hardware. Wall thickness of frame & Mullion shall be 2.4mm., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site, overheads and contractor's profit, etc complete for finished item of work.

Supplying and fixing ornamental MS Grills including fabrication and erection in position using MS square bar rods including cost and conveyance of all materials to work site, all operational, incidental Labour charges for fabrication, cost of welding rods, power charges, cost of fixing in position, overheads & contractors profit etc., complete for finished item of work.

Supplying and fixing stainless steel works such as raling, hand rail, grills etc., using Stainless Steel Tubes, sections, plates, sheets & pipes of all sizes & Diameters for - 304 Grade as per the approved drawing including cost and conveyance of all materials to site, Labour charges for Fabrication of stainless steel works using stainless steel welding rods including buffing, polishing, lacquer finishing, to present seamless finish, overheads & contractors profit etc ., complete for finished item of work.

Supplying and providing of expansion joint filler board conforming to IS: 1838 - 25 mm THICK between the members while casting (columns, beams, slabs etc) as directed by the Engineer-in-Charge including cost of and overheads & contractors profit etc., complete for fnished item of work

Providing specialized polysulphide sealant treatment to the expansion joints (Size : 25 mm x 25 mm) duly a]. Chipping and removing of existing covering on expansion joints b]. Cleaning of the surface from dirt, dust and other contaminations c].Application of one coat of - High performance specially designed SBR latex polymer based bonding agent d]. Providing and application of Acrylic Polymer modified reinstatement concrete /mortar to the damaged edges of joint and making the groove. e]. Providing and fixing of masking tape on top of the joint both sides f]. Providing and fixing of Back up support material of PVC Solid Backer rod to leave the depth of 25 mm on the joint g]. Providing and application of one coat of polysulphide primer on inner edges of Joint. h]. Providing and application of Two part Polysulphide sealant to a width of 25 mm and depth of 25 mm with putty knife and neat finish i]. Removing of masking tape and providing and application of two coats of Acrylic elastomeric cementitious coating

Providing 10mm thick UV resistant multiwall polycarbonate sheets fixed to the purlins with aluminum universal glazing set 40mm wide for jointing and fixing sheets and 14 size self-drilling screws with neoprene washer. Side laps are stitched with self-tapping / drilling screws. End laps are to be sealed with 25x3 mm Butyl tape including cost and conveyance of all materials and labour charges, overheads and contractor's profits, etc. complete for finished item of work

Providing 110 mm dia 3 M Single Socket PVC/SWR pipe - 4 Kg/sq.cm of ISI marked including cost of necessary PVC Bends, shoes, PVC clamps and all other accessories and fixing in position including cost and conveyance of all materials to site, operational & incidental charges, all labour charges for fixing at site etc., and Overheads & Contractors profit complete for finished item of work. (APSS No. 1328)

Supplying, fitting and placing thermo Mechanically Treated (TMT) (Fe 500/500D/550D grade as per IS 1786-1979 manufactured by Category A Major Steel Manufacturers including PSUS's with minimum installed Production Capacity above l0 Lakh MT Per annum (SAIL,VSP STEEL, TATA, JINDAL PANTHER ) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars to site, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying on all materials etc. ,and cost of overheads & contractors profit etc., complete for finished item of work ( APSS No.126)

Providing Mild steel (MS) steel bars ( (Fe 250 grade as per IS 432) of different diameters including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars to bars, including all wastages such as overlaps, couplings, chairs, spacer bars, including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying on all materials and cost of overheads & contractors profit etc., complete for finished item of work in all floors.( APSS No.126)

THIRD FLOOR : Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For Columns in

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) Fo rWALL 200 MM

Vibrated Reinforced Cement Concrete M 25 Design Mix ( by weigh batching / Mixer ) using 20mm size (SS5) hard blasted Trap crushed graded metal (Coarse aggregate) from approved quarry, using a minimum quantity of 380 kgs. of cement per 1 cum of concreteincluding cost and conveyance of all materials like cement, fine aggregate (Sand), coarse aggregate, water etc., to site and cost of all materials including centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates,etc., shuttering , machine mixing, laying concrete, vibrating,lift charges, curing etc., complete but excluding cost of steel and it’s fabrication charges but excluding seigniorage charges for finished item of work (APSS No. 402 & 403) For Roof Beams

Supply and placing of Design Mix Concrete M 25 grade corresponding to IS 456 with minimum cement content of 380 kgs per 1 cum of concrete using Batching Plant of capacity 50 cum per hour and transporting concrete to site by Transit mixer of 2cum capacity and pumping concrete; using pump and with 20mm size graded machine crushed hard Granite metal (coarse aggregate)(consisting of nominal size metal 60% of 20mm, 15% of 13.20/12.50mm, 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing and cost of overheads & contractors profit etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) FOR Slab 150mm thick

Supply and placing of Design Mix Concrete M20 grade corresponding to IS 456 with minimum cement content of 350 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard Granite metal (coarse aggregate)(consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing and cost of overheads & contractors profit etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) FOR LINTELS

Supply and placing of the Design Mix Concrete M 20 grade corresponding to IS 456 with minimum cement content of 350 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard Granite metal (coarse aggregate) ( consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) (with 50% river sand & 50% manufactured sand) coarse aggregate, water etc., to site, centering using Steel scaffolding pipes, jack Props, wallers, Foot plates, brackets, steel Centering Plates, etc., for 60 cm wide sun-shades 7.5cm thick at fixed end and 5cm thick at free end with an average thickness of 6.25cm including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting concrete, laying concrete, curing, cost of overheads & contractors profit complete etc., but excluding cost of steel and its fabrication charges for finished item of work for sunshades (APSS No. 402, 403 & 903) & 903)

Solid Fly-ash Block masonry 225 mm thick for panel walls in super structure, parapet walls with cement mortar (1:6) prop (Cement:sand) using solid fly-ash blocks of size 290 x 225 x 140 mm from approved source having minimum crushing strength of 5 N/sq.mm. including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), bricks, water etc., to site, excluding seigniorage on all materials but including all incidental and operational, labour charges like mixing cement mortar, scaffolding charges (with MS Jack Prop Cup lock Pipe Scaffolds, constructing masonry, lift charges, curing overheads & contractors profit etc., complete for finished item of work as per SS 504. for:-Fly Ash Block Masonry in CM 1:6 (290x225x140)

Ornamental ceiling plastering 12mm thick using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8 mm thick in CM(1:5) and top coat of 4mm thick in CM(1:3) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work .(SS 901,903 & 904)

Plastering 12mm thick in two coats using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials, cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Plastering 12mm thick in two coats using screened sand (with 50% river sand and 50% Manufactured sand) with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site, all operational, incidental charges on materials, cost of all labour charges for mixing mortar, finishing, scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) , lift charges, curing, cutting grooves as directed by Engineer - in - charge etc., and overheads & contractors profit complete for finished item of work. (SS 901,903 & 904)

Providing and applying synthetic plaster putty or equivalent putty of white cement or polymer or cement based such as birla wall care putty or equivalent of average 2 to 3 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying putty paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads and contractors profit for finished item of work for external walls - including cost of access scaffolding(with MS Jack Prop Cup lock Pipe Scaffolds) for:-External Putty

Providing and applying Exterior grade texture ready mixed paint with sand texture added sand particles Acrylic copolymers and mineral compounds, bactericides and various additives having VOC (Volatile Organic Compound) content less than 30 grams/ Lit or equivalent of average 2 to 3 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying texture paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads and contractors profit for finished item of work for external walls - including cost of access scaffolding (with MS Jack Prop Cup lock Pipe Scaffolds) for:-External Colouring - Providing / Texture to External walls.

Providing impervious coat to exposed RCC roof slab surfaces to required slopes with CM (1:3) prop. using screened sand 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by Engineer-in-charge at 1 Kg per one bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand (with 50% river sand & 50% manufactured sand), water proofing compound, water etc., to site, all operational, incidental, and labour charges for mixing mortar, laying, lift charges, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc., and overheads & contractors profit complete for finished item of work. (APSS No. 901 & 903).

Supplying, fitting and placing thermo Mechanically Treated (TMT) (Fe 500/500D/550D grade as per IS 1786-1979 manufactured by Category A Major Steel Manufacturers including PSUS's with minimum installed Production Capacity above l0 Lakh MT Per annum (SAIL,VSP STEEL, TATA, JINDAL PANTHER ) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars to site, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying on all materials etc. ,and cost of overheads & contractors profit etc., complete for finished item of work ( APSS No.126)

WATER SUPPLY ARRANGEMENTS : Supplying & fixing of 3" (75 mm nominal size ) Nahany Trap with Jali - UPVC/SWR Pipe fittings, including cost and conveyance of all materials to site, all operational, incidental, labour charges, overheads & contractors profit etc. complete for finished item of work.

Supplying & Fixing Orissa Pan White glazed W.C 1st quality ISI marked conforming to IS:2556-Part-3-2004 with "P" or "S" trap : 580 mm x 440 mm duly providing constructing Brick masonry seat using 2nd class bricks, CC Squatting plate in P.C.C 1:2:4, S&F PVC Low level system with internal components & short bend: 10 Litres capacity Single Flush, S&F of 15 mm brass angle stop valve of quarter turn spindle type of not less than 400 grams weight with internal threaded conforming to IS 8931 and S&F 15 mm nominal size PVC connection with brass union nut C.P coated including cost and conveyance of all materials , operational, incidental, labour charges, overheads and contractor's profit etc.,. complete as per standard practice for finished item of work.

Supplying and fixing approved make wash down European Water Closet of 1st quality conforming to IS:2556-Part-2- 2004 of white glazed with 'S' trap with CI short Connector & 4" dia CP thimble pipe: 150 mm long, best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996, PVC low level system with internal components & short bend: 10 Litres capacity Single Flush, 15 mm brass angle stop valve of quarter turn spindle type of not less than 400 grams weight with internal threaded conforming to IS 8931 and 15 mm nominal size PVC connection with brass union nut C.P coated all of approved make, including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc.,. complete as per standard practice for finished item of work.

Supplying & Fixing Indian make below counter Wash Hand Basin 1st quality with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/ Senior/ Nice/ Esso or equivalent complete with standard CI brackets including wooden block with single CP pillar cock, including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all respects.

Supplying & Fixing white glazed flat back half stall urinals 1st quality conforming to IS:2556-1995 with standard C.P. Spreader fixed with screws complete Indian make : 590 x 375 x 390 mm, fitted with 15 mm brass body CP finish self closing tap push type conforming to IS 1711 and 30 mm nominal size dia PVC flexible waste pipe of 914.4 mm length of Ist quality including cost and conveyance of all materials to site, all operational,incidental, labour charges, overheads and contractor's profit etc. complete for finished item of work in all respects.

Supplying and fixing of SWR PVC pipes of 6 Kg/Sq.cm. and fixing all specials such as plain bends, off sets, door bends, single junctions, double junctions etc., as per site requirement, fixing with PVC clamps with required number of Bombay nails etc., with solvent jointing as per standard practice including cost and conveyance of all materials to site, all operational, incidental, labour charges, overheads & contractors profit etc., complete for finished item of work at all floor levels . (APSS No. 1302 1319 & 1326) 160mm dia

Supplying and fixing of SWR PVC pipes of 4 Kg/Sq.cm. and fixing all specials such as plain bends, off sets, door bends, single junctions, double junctions etc., as per site requirement, fixing with PVC clamps with required number of Bombay nails etc., with solvent jointing as per standard practice including cost and conveyance of all materials to site, all operational, incidental, labour charges, overheads & contractors profit etc., complete for finished item of work at all floor levels . (APSS No. 1302 1319 & 1326) 75mm dia

Supplying and fixing of SWR PVC pipes of 4 Kg/Sq.cm. and fixing all specials such as plain bends, off sets, door bends, single junctions, double junctions etc., as per site requirement, fixing with PVC clamps with required number of Bombay nails etc., with solvent jointing as per standard practice including cost and conveyance of all materials to site, all operational, incidental, labour charges, overheads & contractors profit etc., complete for finished item of work at all floor levels . (APSS No. 1302 1319 & 1326) 110mm dia

S & F 65 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs including excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent, with necessary excavation in all types of soils (except rock requiring blasting) refilling and making good the walls and floors to the original surface, fixing M.S. clamps and T.W. block on walls wherever required, including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit, etc. complete for finished item of work as directed by Engineer-in-charge.

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for 15.90mm dia OD Pipe SDR 11..rate inclusive of CP & OH

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for 22.20 mm dia OD Pipe SDR 11..rate inclusive of CP & OH

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for 28.60 mm dia OD Pipe SDR 11..rate inclusive of CP & OH

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for 34.90 mm dia OD Pipe SDR 11..rate inclusive of CP & OH

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for41.30 mm dia OD Pipe SDR 11..rate inclusive of CP & OH

Supply and laying of ASHIRVAD or equivalent CPVC Pipes and Fittings or equalant for Hot & Cold conforming to IS 15778:2007 with malleable specials such as Tees, Elbows, check nuts, unions, bushes, etc, with hot pressed joints with required solution including fixing in walls ceiling floors Include for necessary excavation in all sorts of soils, chasing in the walls etc, refilling consolidation with the excavated earth & Making bores in walls ceiling etc. and making good the chased surface in cement mortar and complete. When making a transition use metal threads fittings, including cost, all taxes and all labour charges for all operations and transportation etc., complete for finished item of work as directed by the Engineer In charge for 54.00 mm dia OD Pipe SDR 11..rate inclusive of CP & OH

S & F 15mm Bronze Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all floors as directed by Engineer-in-charge.

S & F 25mm Bronze Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all floors as directed by Engineer-in-charge.

S & F 32 mm Bronze Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all floors as directed by Engineer-in-charge.

S & F 40mm Bronze Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all floors as directed by Engineer-in-charge.

S & F 50mm Bronze Ball valve with SS Ball and SS Spindle as per IS - Class - I, Indian make heavy type including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit etc. complete for finished item of work in all floors as directed by Engineer-in-charge.

S&F of Chromium plated finish brass body quarter turn Bibcock cum Health Faucet with 1m long tube and wall hook with 10 years warranty, including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit, etc. complete for finished item of work.

S&F of 15 mm brass body CP finish bib tap of not less than 300 grams weight with quarter turn spindle with either internal or external threaded conenction conforming to IS 8931, including cost and conveyance of all materials to site, all operational,incidental , labour charges, overheads and contractor's profit, etc. complete for finished item of work.

Electrical :- Supply and Laying of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in Roof Slabs with all required PVC Deep Boxes including masonary work and labour charges etc., complete. Makes : Sudhakar / Finolex / Modi / VIP/ Precision

Supply and laying of ISI 25mm outer dia medium grade with IS:9537 part 3 regid PVC pipe consealed in wall with Metallic junction boxes and all required accessories including masonary work for light, fan and separate plug point with including all labour charges etc., complete. Makes : Sudhakar / Finolex / Modi / VIP / Precision

Supply and laying of ISI 25mm outer dia medium grade, with IS:9537 part 3 rigid PVC concealed in wall with all required PVC Junction Boxes including masonary work and labour charges etc., Makes : Sudhakar / Finolex / Modi / VIP/ Precision

Supply and erecting GI / MS Galvanished fan hook box with hook in RCC slab including all labour charges etc.,complete.

Wiring with run of 2 of 1.5 Sqm HFFR PVC insulated 1100V grade class-II Conductor IS:694 / 2010, IS17048 specification for Copper cable make in existing consealed pipe ferrules including supply and fixing of 3 Plate Jumbo Ceiling rose/batten holder of Anchor / Gold Medal Olive / Million Zoom make and 6A ISI marked Modular type switch including cost and conveyance of all material and all labour charges etc., complete for light and bell points in N.R.B. Wire Makes: Makes: Finolex/ RR kabel/ Havells. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Wiring with run of 2 of 1.5 Sqmm class-II Conductor HFFR PVC insulated 1100V grade as per IS:694/2010 , IS 17048 specification for Copper cable in existing PVC conduit pipe ferrules including Supply and fixing of Jumbo Ceiling rose and 6 / 10A ISI Mark 1way Modular switch with required modular box and cover frame in existing Surface or Concealed pipe wiring including cost and conveyance of all material and all labour charges etc., complete for Stair case light points in N.R.B. Wire Makes: Finolex/ RR kabel/ Havells. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Wiring with run of 3 of 1.5 Sqmm class-II Conductor HFFR PVC insulated 1100V grade as per IS:694/2010 , IS 17048 specification for Copper cable in existing PVC conduit pipe ferrules including Supply and fixing of Jumbo Ceiling rose and 6 / 10A ISI Mark 1way Modular switch with required modular box and cover frame in existing Surface or Concealed pipe wiring,ferrules including cost and conveyance of all material and all labour charges etc., complete for fan and exhaust fan points in R.B. Wire Makes: Makes : Finolex / RR kabel / Havells. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Supply and fixing of 10A 3 Pin 2 Module Modular Socket with shutter with 6 / 10A 1 Way 1 Module Modular Switch, 3 Module box with cover frame in Common switch board including cost and conveyance of all materials and all labour charges etc., complete in N.R.B. / R.B. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Supply and fixing of 16A / 6A 2 Module Combi Socket Modular Socket with shutter with 16A/20A 1 Way 1 Module Modular Switch fixed on suitable size Modular box with required cover frame including with connections, cost and conveyance of all material and all labour charges etc., complete in N.R.B. / R.B. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Supply and fixing of 6 / 10A 1 Way 1 Module Modular Switches - 2 Nos and 10A 3 Pin 2 Module Modular Socket with shutter - 2 Nos Modular type with cover plate and Modular box fixing on separate board including all labour charges etc., complete. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus /Panasonic Vision.

Supply and Run of 3 of 2.5 Sqmm class-II Conductor HFFR PVC insulated 1100V grade as per IS:694/2010 , IS 17048 specification for Copper cable in existing pipe with ferrules for run of mains,inlcuding all labour charges etc., complete. Wire Makes: Finolex / RR kabel / Havells.

Supply and Run of 3 of 4.0 sq mm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specifications for Copper cable in existing pipe with ferrules for power points and AC Sockets inlcuding all labour charges etc., complete. Makes : Finolex / RR kabel / Havells /Polycab

Supply and Run of 5 of 6.0 Sq.mm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specifications for Copper cable in the existing conduit pipe with ferrules for run of mains from VTPN / Panel Board to TPN DB"s with pin type lugs and connections etc., complete. [for LDBs] Makes : Finolex / RR kabel / Havells /Polycab

Supply and Run of 5 of 10.0 Sq.mm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specifications for Copper cable in the existing conduict pipe with ferrules for run of mains from VTPN / Panel Board to TPN DB"s with pin type lugs and connections etc., complete. [for PDBs] Makes : Finolex / RR kabel / Havells /Polycab

Supply, transportation and fixing of 18W +/- 10% (>=1800 Lumens) LED back lit LED Down Light Recessed / Surface mounting round / square with housing made of Powder coated Pressure die cast aluminium housing with extended heat sink, with Protruded high efficiency diffuser, IP20, with wide operating voltage range, Power factor > 0.9, Surge protection: > 2KV, System efficacy of >100 lumens/watt, CCT: 3000K - 6500K as desired by the department and as per IS, CRI >80, and THD is less than 15% etc., complete with 5 years warranty with BIS Certification. LUMINAIRE MAKE : Phillips / Wipro / Crompton / Havells LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.

Supply, transportation and Fixing of 22W, +/ 10% , >/ 2300 lumens, 1200mm(+/- 10%) length LED light housing made with alluminium anodised body, wide operating voltage with PF≥0.9, Surge protection: > 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 6500K as desired by the department as per IS, minimum CRI≥80 etc., complete with 5 years warranty with BIS Certification with BIS Certification. LUMINAIRE MAKE : Phillips / OSRAM / Wipro / Crompton / Havells LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.

Supply, Transportation and Fixing of 30-36W +/- 10% (>=3960Lumens) Back lit, 2' x2' grid false ceiling / zip board (595 mm x 595 mm) Recessed / Surface mounted LED luminaire made of CRCA sheet housing with powder coated with high efficiency acrylic wide diffuser, with wide operating voltage range, Power factor > 0.9, Surge protection >2KV, System efficacy of >110 lumens/watt, CCT: 3000K - 6500K as desired by the department, CRI >80, and THD is less than 15% etc., complete with 5 years warranty with BIS Certification. LUMINAIRE MAKE : Phillips / Wipro / Crompton / Bajaj / Havells LED Make: Philips Lumileds/Cree/Nichia/Osram/Samsung/LG LEDs.

Supply and transportation of 24W +/- 10% (>=2400 Lumens) LED back lit LED Down Light Recessed / Surface mounting round / square with housing made of Powder coated Pressure die cast aluminium housing with extended heat sink, with Protruded high efficiency diffuser, IP20, with wide operating voltage range, Power factor > 0.9, Surge protection: > 2KV, System efficacy of >100 lumens/watt, CCT: 3000K - 6500K as desired by the department and as per IS, CRI >80, and THD is less than 15% etc., complete with 5 years warranty with BIS Certification. LUMINAIRE MAKE : Phillips / Wipro / Crompton / Havells LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs.

Supply, Transportation and fixing of energy efficient decorative fan, 1200 mm sweep, aluminium body, consuming 28 W, BEE 5 star rated, ceiling fan with Brush Less Direct Current(BLDC)motor, class of insulation: F, 3 no's blades, 30 cm long down rod, 2 no's canopies, shackle kit, copper winding, Power Factor greater than 0.90, Service Value (CMM/W) greater than 8.6, Air delivery minimum 235 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%, remote or compatible to electronic step type regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75°C (max), insulation resistance more than 2 mega ohm, suitable for 230V, 50 HZ, single phase AC supply, earthing etc., complete.Makes : Atomberg / Havells / Orient / RR / Halonix / Crompton / Bajaj / Goldmedal / GM.

Supply and fixing of Modular type Stepped electronic regulator for sweep AC ceiling fans of 1200mm / 1400mm complete with connections. Makes : Legrand Lyncus / GM Four Five / Million Milltech / Goldmedal Curve / Anchor Roma Plus / Crabtree Verona / Panasonic Vision / Hager Insista / Benlo Vesta / Polycab Levana / Salzar Elite / Elleys E-Soft / Fybros Four-X

Supply, Transportation and Fixing of 12" (300mm) , 900 RPM Heavy duty exhaust fan with metallic blades for General Toilets with all labour charges etc., complete as directed at site.Makes: Crompton / Almonard / Havells Turbo Force SP. Twin Core Wire Makes: Finolex / RR kabel / Havells.

Supply and fixing of GI louver shutter including GI mesh to avoid birds entry with necessary materials suitable for 12" (300 mm) Exhaust fan.

Supply, Transportation and Run of Cat - 6 UTP cable for LAN in the existing conduit pipe and labour charges etc., complete. Makes : D Makes : D Link / AMP / Molex / Legrand/ Krone / R & M.

Supply and fixing of Cat 6 RJ-45 information outlets including single face plate of makes D Link / AMP / Molex / Legrand / Krone on required size Modular Box with cover frame with connections including cost and conveyance of all material and all labour charges etc., complete in N.R.B.

Supply, Transportation and Run of 1 of 2 Pair 0.5mm telephone copper cable in the existing conduit pipe and labour charges etc., complete. Makes : Finolex / / Surabi / Polycab.

Supply and fixing of Modular telephone Jack with connector on modular box with cover frame in existing consealed pipe wiring including cost and coveyance of all material and all labour charges etc., complete in N.R.B. / R.B. Makes : Legrand Lyncus / GM Four Five / Goldmedal Curve /Anchor Roma Plus / /Panasonic Vision

Supply and fixing of 7 feet length moulded patch cord including accessories and all labour charges etc complete.

Supply and fixing of 3 feet length moulded patch cord including accessories and all labour charges etc complete.

Supply and fixing of 24 Port 10/ 100/ 1000 Gigabit Unmanageable Ethernetswitches including accessories and all labour charges etc complete. Makes: TP Link / D link / Netfox .

Supply and fixing of 24 port patch panels including accessories and all labour charges etc complete. Makes : D Link / AMP / Molex / Legrand / Krone.

Supply and installation of 9U Wall 600 mm width x 500 mm depth UL certified wall mounting network rack with sheet steel revited metal frame,top and bottom cover with brush cable entry,confirming to following standards IEC 60529,EN 60529 ( IP 20), IEC 62262 EN 62622 (IK 08) , DIN 41494, EIA 310, IEC 60927 includingall accessories like horizontal PDU, metal cable manager, hardware packet and the cantilever shelf etc.,complete. Makes : Vallrack (Legrand) /Netrack.

Supply and installation of 15U Wall 600 mm width x 500 mm depth UL certified wall mounting network rack with sheet steel revited metal frame,top and bottom cover with brush cable entry,confirming to following standards IEC 60529,EN 60529 ( IP 20), IEC 62262 EN 62622 (IK 08) , DIN 41494, EIA 310, IEC 60927 includingall accessories like horizontal PDU, metal cable manager, hardware packet and the cantilever shelf etc.,complete. Makes : Vallrack (Legrand) /Netrack.

Supply and installation of IP 20, IK 08 42U 600mm Width x 1000mm Deep Floor mounting network rack with all accessories like front and rear doors, fans, castor wheels (2 with break and 2 without break), cable manager, cantilever shelf, horizontal and vertical power distribution unit, monitor shelf, brush at cable entry and hardware packet, etc. Mod cap floor stand : Modular construction of the rack made of 4 vertical , 4 Horizontal and 4 depth alloy extruded multi folded hallow profiles bolted and joined together with links and corner blocks. 3 Pairs of support channels to equate the load evenly and castor provision at bottom side. Painting shade : Combination of RAL 7035 / 7037 fine texture - 60 to 80 microns. or RAL 9005 fine texture - 60 to 80 microns complies with standards : UL 2416, Din 41494, IEC EN 60529, IEC EN 62262, IEC EN 60068-2-11, ISO 9001- 2008. Makes : Vallrack (Legrand) / Netrack.

P Based digtal Telephone (EPABX) system complied with following specifications: > IP @ Core, PCM/TDM, Non blocking, > Must Support PRI, E1, Analog Junctions > Must Support PC Console, > Must support Mobile SIP (Android and I O.S) > Must support Voice Mail > Must support Card based GSM > Inbuilt Call Details Software with search engine software > 4 Analog Trunks > 6 Digital Extensions > 64 Analog Extensions > 1 Digital Key Phone with minimum 16 Keys (Must work only on 2 wires) > Expandable to 96 Analog Extensions or more Makes: NEC/ Alcatel/ Karel/ Unify / Matrix

Supply and Installation of Digital Key Telephone with 2 line display, 16 programmable keys, fully handsfree talk back.

Supply and installation of Analog Push Button telephone with caller ID facility etc complete

Providing independent earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe gig earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

Supply and Run of 25mm x 6mm G.I Strip including cost of all accessories and labour charges etc., complete. (1.18Kgs/1Mtr)

Supply and fixing 4 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 1 No 4 pole Incomer of 63A FP RCBO and 12No. 6-32A 10kA ISI Marked C/D Curve SP MCBs with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc complete with inter connections and labour charges for Flush Mounting etc., complete. DB Makes : Legrand / Schneider. RCBO & MCB Makes : Legrand-DX3 / Schneider-Acti9

Supply and fixing 4 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 1 No 4 pole Incomer of 40A FP RCBO and 12No. 6-32A 10kA ISI Marked C/D Curve SP MCBs with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc complete with inter connections and labour charges for Flush Mounting etc., complete. DB Makes : Legrand / Schneider. MCB & Isolator Makes : Legrand-DX3 / Schneider-Acti9

Supply and fixing of 8 way VTPN DB IP 43 Protection as per IS:13032 With and suitable for 1 No 160A 4 pole MCCB Incomer and 8 Nos 63 A 10 kA TP MCB, ISI Marked C/D CURVE with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc complete with inter Connections and labour charges for Flush Mounting etc., complete. DB Makes : Legrand / Schneider. MCCB Make: L&T- D sine / Schneider-NS NSX/Legrand-DP X3/ Siemens-3VL / Hager-h3/C&S -Winbreak. MCB Makes : Legrand-DX3 / Schneider-Acti9

Supply and laying of 185 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I). Makes : Torrent / Unicab / Universal /Polycab / Havells /KEI /Finolex / Payal / RR kable

Supply and fixing of heavy duty long barrel alluminium lugs confirming to I.S specifications suitable for Up to 185 Sq.mm -cable etc complete with nuts, bolts and washers. Makes: DMI / Jainson / Dowels or equivalent make as approved by the department

Supply and fixing of heavy duty long barrel alluminium lugs confirming to I.S specifications suitable for Up to 95 Sq.mm -cable etc complete with nuts, bolts and washers. Makes: DMI / Jainson / Dowels or equivalent make as approved by the department

Supply of 16 sqmm 4 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:2010 including all transportation charges etc complete. Makes : Finolex / RR kabel / Havells / Polycab / RPG / KEI

Supply and fixing of heavy duty long barrel copper lugs confirming to I.S specifications suitable for Up to 16 Sq.mm -cable etc complete with nuts, bolts and washers. Makes: DMI / Jainson / Dowels or equivalent make as approved by the department

Supply and fixing of heavy duty type double compression weather proof type brass cable glands duly nickel plated as per BS 6121 and IP66 complete with brass checknut, outer sheath sealing gasket suitable for 16 Sqmm 4core - XLPE insulated armoured cable etc complete. Makes: SMI / Commet / Dowels

Supply, installation, testing and commissioning of floor mounting type panel board with Alluminium bus bars fabricated with 14/16 Gauge CRCA Sheet comprising of TPN bus bars of equal size in all phases and neutral equipped with bus bar chambers and cable chambers.The bus bars fault level shall be 50 KA and shall be as per the requirement of local CEIG, fire regulations, CPRI norms and other authorities etc. The painting of the complete system shall be powder coated duly processing the panel in 7 tank process. The panel shall be suitable for accomdating the following switch gear including supply of all components, hard wares etc including all necessary civil works, adequate reinforcement, foundation bolts, suitable G.I earth strip 50 x 6mm, door loop earthings, bus bars should be colour sleeved with heat shrinkable sleeves for phase and neutral duly supported at regular intervels by SMC supports,spider links /bus bar links and all cables shall have proper cable entry, danger board, feeder identification marks, rigid inter connections, cadmium plated bolts and nuts and shall be installed on flooring and consisting of the following as required and as per IS standards for Panel shall be manufacture only from CPRI approval Fabricators.

Supply, Transportation and Installation of 300mm x 50mm x 2mm thickhot dip GI perforated cable tray with cover along with coupler plates, T's, Bends, Reducers, Anchor bolts, nuts, washers and slotted channels / Angle Iron Channels etc complete and the tray should be fitted on the wall / Ceiling etc. complete for finished item of work. Makes: DEC / MNR / Aparna / H FAB or equivalent

Providing independent earthing by exacavating a pit to a depth of 2.25Mtr in all soils as per size specified in the data for Sophisticated Electronic equipment with 600mm x 600mm x 3.15mm thick copper plate rigidly fixed to 19mm dia 'B' Class G.I Pipe of 2.5Mtr lengthwith funnel as per National Electric Code and earth connection from electrode GI strip of 40mm x 5mm x 200mm length to be bolted with nut bolts to G.I.pipe including 25mm x 3mm copper strip of 6Mtrs length connected from plate to GI strip including filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe and providing CC / Brick massonry chamber 450mmX450mmX400mm and covered with R.C.C. Slab including all accessories and labour charges etc complete as per IS specification 732/1982 (Part II).

Supply, Transportation and installation of 20KVA on line UPS system IGBT based rectifier with input power factor correction with isolation transformers double conversion, SNMP controls, LCD display, Pure sine wave out put, with auto static switch three phase input / Single phase output with warranty up to three years.Makes: APC / Numeric / Emerson / Fuji Electric

Supply and fixing of 12V 42AH SMF battery including wire leads. Makes : Quanta / Racket / Exide / Amaron.

Supply and providing of UPS cum battery rack 11 to 20 batteries